SENZ SD5011 OPPVASKMASKIN Omaniku manuaal

Dishwasher

SD5011

User Manual

Thank you for purchasing your new SENZ dishwasher. These

operating instructions will help you use it properly and safely.

We recommend that you spend some time reading this

instruction manual in order that you fully understand all the

operational features it oers. Read all the safety instructions

carefully before use and keep this instruction manual for future

reference.

Takk for at du kjøpte din nye oppvaskmaskinen fra SENZ. Denne

bruksanvisningen vil hjelpe deg med å bruke den på en trygg

og riktig måte. Vi anbefaler at du tar deg tid til å lese gjennom

hele bruksanvisningen for å bli fortrolig med alle funksjonene

som tilbys. Les alle sikkerhetsanvisningene nøye før bruk, og

oppbevar bruksanvisningen for fremtidig referanse.

Kiitos, kun valitsit uuden SENZ-Astianpesukoneen. Nämä

käyttöohjeet opastavat sinua käyttämään laitetta oikein

ja turvallisesti. On suositeltavaa käyttää aikaa tämän

käyttöoppaan lukemiseen, jotta ymmärrät täysin, mitä

toiminnallisia ominaisuuksia tuote tarjoaa. Lue kaikki

turvallisuusohjeet huolellisesti ennen laitteen käyttöä ja

säilytä käyttöopas myöhempää käyttöä varten.

Tak for købet af din nye opvaskemaskine fra SENZ. Disse

brugervejledninger hjælper dig med at bruge dette

apparat rigtigt og sikkert. Vi anbefaler, at du læser denne

brugervejledning, så du får en fuld forståelse af hvordan alle

funktionerne virker. Læs sikkerhedsforskrifterne grundigt

inden brug, og gem denne brugervejledning til senere brug.

Tack för att du har köpt en ny diskmaskinen från SENZ. Denna

bruksanvisning hjälper dig att använda den på ett säkert och

korrekt sätt. Vi rekommenderar att du tar dig tid att läsa igenom

denna bruksanvisning för att till fullo förstå alla driftfunktioner

som den erbjuder. Läs noga igenom alla säkerhetsinstruktioner

före användning och spara bruksanvisningen för framtida bruk.

2

4

9

13

18

48

93

138

183

228

-

9 -

4 -

9 -

4 -

Instruction manual - English ........................page

Bruksanvisning - Norsk .................................. side

Käyttöopas - Suomi ........................................ sivu

Brugervejledning - Dansk .............................. side

Bruksanvisning - Svenska ..............................sida

3

5

SAFETY INFORMATION

WARNING

When using your dishwasher, follow the

precautions listed below:

•Installation and repair can only be carried out by

a qualified technician.

•This appliance is intended to be used in

household and similar applications such as:

- staff kitchen areas in shops, offices and other

working environments;

- farm houses;

- by clients in hotels, motels and other residential

type environments;

- bed and breakfast type environments.

•This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use

of the appliance in a safe way and understand

the hazards involved.

•Children shall not play with the appliance.

Cleaning and user maintenance shall not be

done by children without supervision. (For

EN60335-1) This appliance is not intended for

use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

4

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety. (For IEC60335-1)

•Packaging material could be dangerous for

children!

•This appliance is for indoor household use only.

To protect against the risk of electrical shock, do

not immerse the unit, mains power cable or plug

in water or other liquid.

•Unplug before cleaning and performing

maintenance on the appliance.

•Use a soft cloth moistened with mild soap, and

then use a dry cloth to wipe it again.

Earthing Instructions

•This appliance must be earthed. In the event

of a malfunction or breakdown, earthing will

reduce the risk of an electric shock by providing

a path of least resistance of electric current.

This appliance is equipped with an earthing

conductor plug.

•The plug must be plugged into an appropriate

mains power outlet that is installed and

earthed in accordance with all local codes and

ordinances.

•Improper connection of the equipment-earthing

conductor can result in the risk of an electric

shock.

5

7

•Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

•Do not modify the plug provided with the

appliance; If it does not fit the outlet.

•Have a proper mains power outlet installed by a

qualified electrician.

•Do not abuse, sit on, or stand on the door or dish

rack of the dishwasher.

•Do not operate your dishwasher unless all

enclosure panels are properly in place.

•Open the door very carefully if the dishwasher is

operating, there is a risk of water squirting out.

•Do not place any heavy objects on or stand on

the door when it is open. The appliance could tip

forward.

•When loading items to be washed:

1.Locate sharp items so that they are not likely

to damage the door seal;

2. Warning: Knives and other utensils with sharp

points must be loaded in the basket with their

points facing down or placed in a horizontal

position.

•Some dishwasher detergents are strongly

alkaline. They can be extremely dangerous if

swallowed. Avoid contact with the skin and eyes

and keep children away from the dishwasher

when the door is open.

6

•Check that the detergent powder is empty after

completion of the wash cycle.

•Do not wash plastic items unless they are

marked "dishwasher safe" or the equivalent.

•For unmarked plastic items not so marked, check

the manufacturer's recommendations.

•Use only detergent and rinse agents

recommended for use in an automatic

dishwasher.

•Never use soap, laundry detergent, or hand

washing detergent in your dishwasher.

•The door should not be left open, since this

could increase the risk of tripping.

•If the mains power cable is damaged, it must

be replaced by the manufacturer or its service

agent or a similarly qualied person in order to

avoid a hazard.

•During installation, the power supply must not

be excessively or dangerously bent or attened.

•Do not tamper with controls.

•The appliance needs to be connected to the

main water valve using new hose sets. Old sets

should not be reused.

•To save energy, in stand by mode, the appliance

will switch o automatically while there is no

any operation in 15 minutes.

The maximum number of place settings to be

washed is 12.

7

9

The maximum permissible inlet water pressure

is 1MPa.

The minimum permissible inlet water pressure is

0.04MPa.

Disposal

•For disposing of packaging and the appliance

go to a recycling center. Cut off the power

supply cable and make the door closing device

unusable.

•Cardboard packaging is manufactured from

recycled paper and should be disposed of in the

waste paper collection for recycling.

•By ensuring this product is disposed of correctly,

you will help prevent potential negative

consequences for the environment and human

health, which could otherwise be caused by

inappropriate waste handling of this product.

•For more detailed information about recycling

of this product, contact your local city office and

your household waste disposal service.

•DISPOSAL: Do not dispose this product as

unsorted municipal waste. Collection of such

waste separately for special treatment is

necessary.

8

PRODUCT OVERVIEW

IMPORTANT:

To get the best performance from your dishwasher, read all

operating instructions before using it for the rst time.

Inner pipe

Filter assembly

Cutlery basket

Lower basketUpper basket

Cup rack upper spray arm

Lower spray arm

Salt container

Dispenser

NOTE:

To make room for taller items in the

upper basket, raise the cup rack

upwards. You can then lean the tall

glasses against it. You can also remove

it when it is not required for use.

9

Funnel

USING YOUR DISHWASHER

Before using your dishwasher:

Inside Outside

1. Set the water softener

2. Loading the Salt Into the Softener

3. Loading the basket

4. Fill the dispenser

NOTE:

Check the section “Water Softener” If you need to set the water

softener.

Loading The Salt Into The Softener

NOTE:

If your model does not have any water softener, you may skip this

section.

Always use salt intended for dishwasher use.

The salt container is located beneath the lower basket and should be

lled as explained in the following:

WARNING

Only use salt specically designed for dishwashers use!

Every other type of salt not specically designed for dishwasher

use, especially table salt, will damage the water softener. In case

of damages caused by the use of unsuitable salt the manufacturer

does not give any warranty nor is liable for any damages caused.

Only ll with salt before running a cycle.

This will prevent any grains of salt or salty water, which may have

been spilled, remaining on the bottom of the machine for any

period of time, which may cause corrosion.

z

10

Follow the steps below for adding dishwasher salt:

1. Remove the lower basket and unscrew the reservoir cap.

2. Place the end of the funnel (supplied) into the hole and pour in

about 1.5kg of dishwasher salt.

3. Fill the salt container to its maximum limit with water, It is normal

for a small amount of water to come out of the salt container.

4. After lling the container, screw back the cap tightly.

5. The salt warning light will stop blinking after the salt container

has been lled with salt.

6. Immediately after lling the salt into the salt container, a washing

program should be started (We suggest to use a short program).

Otherwise the lter system, pump or other important parts of the

machine may be damaged by salty water. This is out of warranty.

NOTE:

The salt container must only be relled when the salt warning light

() in the control panel comes on. Depending on how well the salt

dissolves, the salt warning light may still be on even though the

salt container is lled. If there is no salt warning light in the control

panel (for some Models), you can estimate when to ll the salt into

the softener by the cycles that the dishwasher has run.

If salt has spilled, run a soak or quick program to remove it.

11

13

MAINTENANCE AND CLEANING

External Care

The door and the door seal

Clean the door seals regularly with a soft damp cloth to remove

food deposits. When the dishwasher is being loaded, food and drink

residues may drip onto the sides of the dishwasher door. These

surfaces are outside the wash cabinet and are not accessed by water

from the spray arms. Any deposits should be wiped off before the

door is closed.

The control panel

If cleaning is required, the control panel should be wiped with a soft

damp cloth only.

WARNING

zTo avoid penetration of water into the door lock and electrical

components, do not use a spray cleaner of any kind.

zNever use abrasive cleaners or scouring pads on the outer surfaces

because they may scratch the finish. Some paper towels may also

scratch or leave marks on the surface.

Internal Care

Filtering system

The filtering system in the base of the wash cabinet retains coarse

debris from the washing cycle. The collected coarse debris may cause

the filters to clog. Check the condition of the filters regularly and

clean them if necessary under running water. Follow the steps below

to clean the filters in the wash cabinet.

NOTE:

Pictures are only for reference, different models of the filtering

system and spray arms may be different.

12

Main lter

Coarse lter

Fine lter

1. Hold the coarse lter and

rotate it anticlockwise to

unlock the lter. Lift the lter

upwards and out of the

dishwasher.

2. The ne lter can be pulled o

the bottom of the lter

assembly. The coarse lter can

be detached from the main

lter by gently squeezing the

tabs at the top and pulling it

away.

3. Larger food remnants can be

cleaned by rinsing the lter

under running water. For a

more thorough clean, use a

soft cleaning brush.

4. Reassemble the lters in the

reverse order of the

disassembly, replace the lter

insert, and rotate clockwise to

the close arrow.

WARNING

Do not over tighten the lters. Put the lters back in sequence

securely, otherwise coarse debris could get into the system and

cause a blockage.

Never use the dishwasher without lters in place. Improper

replacement of the lter may reduce the performance level of the

appliance and damage dishes and utensils.

13

15

Spray arms

It is necessary to clean the spray arm regularly for hard water

chemicals will clog the spray arm jets and bearings.

To clean the spray arm, follow the instructions below:

1. To remove the upper spray

arm, hold the nut, rotate the

arm clockwise to remove it.

2. To remove the lower spray

arm, pull out the spray arm

upwards.

3. Wash the arms in soapy and

warm water and use a soft

brush to clean the jets. Replace

them after rinsing them

thoroughly.

Caring For The Dishwasher

Frost precaution

Take frost protection measures on the dishwasher in winter. Every

after washing cycles, operate as follows:

1. Cut off the electrical power to the dishwasher at the supply

source.

2. Turn off the water supply and disconnect the water inlet pipe from

the water valve.

14

3. Drain the water from the inlet pipe and water valve. (Use a pan to

gather the water)

4. Reconnect the water inlet pipe to the water valve.

5. Remove the lter at the bottom of the tub and use a sponge to

soak up water in the sump.

After every wash

After every wash, turn o the water supply to the appliance and

leave the door slightly open so that moisture and odors are not

trapped inside.

Remove the plug

Before cleaning or performing maintenance, always remove the plug

from the mains power socket.

No solvents or abrasive cleaning

To clean the exterior and rubber parts of the dishwasher, do not

use solvents or abrasive cleaning products. Only use a cloth with

warm soapy water. To remove spots or stains from the surface of

the interior, use a cloth dampened with water an a little vinegar, or a

cleaning product made specically for dishwashers.

When not in use for a longtime

It is recommend that you run a wash cycle with the dishwasher

empty and then remove the plug from the mains power socket, turn

o the water supply and leave the door of appliance slightly open.

This will help the door seals to last longer and prevent odors from

forming within the appliance.

Moving the appliance

If the appliance must be moved, try to keep it in the vertical position.

If absolutely necessary, it can be positioned on its back.

Seals

One of the factors that cause odours to form in the dishwasher is

food that remains trapped in the seals. Periodic cleaning with a damp

sponge will prevent this from occurring.

15

17

INSTALLATION INSTRUCTION

WARNING

Electrical Shock Hazard

Disconnect electrical power before installing

dishwasher.

Failure to do so could result in death or electrical shock.

Attention

The installation of the pipes and electrical equipments should be

done by professionals.

About Power Connection

WARNING

For personal safety:

zDo not use an extension cord or an adapter plug with this

appliance.

zDo not, under any circumstances, cut or remove the earthing

connection from the cable.

Electrical requirements

Look at the rating label to know the rating voltage and connect the

dishwasher to the appropriate power supply. Use the required fuse

10A/13A/16A, time delay fuse or circuit breaker recommended and

provide separate circuit serving only this appliance.

Electrical connection

Ensure the voltage and frequency of the power being corresponds

to those on the rating plate. Only insert the plug into an electrical

socket which is earthed properly. If the electrical socket to which the

appliance must be connected is not appropriate for the plug, replace

the socket, rather than using a adaptors or the like as they could

cause overheating and burns.

Ensure that proper earthing exists before use

Water Supply And Drain

Cold water connection

Connect the cold water supply hose to a threaded 3/4(inch)

connector and make sure that it is fastened tightly in place.

If the water pipes are new or have not been used for an extended

16

period of time, let the water run to make sure that the water is clear.

This precaution is needed to avoid the risk of the water inlet to be

blocked and damage the appliance.

ordinary supply hose

safety supply hose

About the safety supply hose

The safety supply hose consists of the double walls. The hose's

system guarantees its intervention by blocking the ow of water in

case of the supply hose breaking and when the air space between

the supply hose itself and the outer corrugated hose is full of water.

WARNING

A hose that attaches to a sink spray can burst if it is installed on

the same water line as the dishwasher. If your sink has one, it is

recommended that the hose be disconnected and the hole plugged.

How to connect the safety supply hose

1. Pull The safety supply hoses completely out from storage

compartment located at rear of dishwasher.

2. Tighten the screws of the safety supply hose to the faucet with

thread 3/4inch.

3. Turn water fully on before starting the dishwasher.

How to disconnect the safety supply hose

1. Turn o the water.

2. Unscrew the safety supply hose from the faucet.

Connection Of Drain Hoses

Insert the drain hose into a drain pipe with a minimum diameter

of 4 cm, or let it run into the sink, making sure to avoid bending or

crimping it. The height of drain pipe must be less than 1000mm. The

free end of the hose must not be immersed in water to avoid any

back ow occurring.

17

19

Securely fix the drain hose in either position A or position B

Back of dishwasher

Mains Cable

Drain pipe

Water Inlet

Drain hose

MAX 1000mm

Counter

How to drain excess water from hoses

If the sink is 1000mm higher from the floor, the excess water in

hoses cannot be drained directly into the sink. It will be necessary to

drain excess water from hoses into a bowl or suitable container that

is held outside and lower than the sink

Water outlet

Connect the water drain hose. The drain hose must be correctly

fitted to avoid water leaks. Ensure that the water drain hose is not

kinked or squashed.

Extension hose

If you need a drain hose extension, make sure to use a similar drain

hose. It must be no longer than 4 meters; otherwise the cleaning

effect of the dishwasher could be reduced.

Syphon connection

The waste connection must be at a height less than 100 cm

(maximum) from the bottom of the dishwasher. The water drain hose

should be fixed.

Position The Appliance

Position the appliance in the desired location. The back should rest

against the wall behind it, and the sides, along the adjacent cabinets

18

or walls. The dishwasher is equipped with water supply and drain

hoses that can be positioned either to the right or the left sides to

facilitate proper installation.

Levelling the appliance

Once the appliance is positioned for

levelling, the height of the dishwasher

may be altered via adjustment of the

screwing level of the feet. In any case,

the appliance should not be inclined more

than 2°.

NOTE:

Only apply to the free standing dishwasher.

Built-In Installation (for the integrated model)

Step 1. Selecting the best location for the dishwasher

The installation position of dishwasher should be near the existing

inlet and drain hoses and mains power cable.

Illustrations of cabinet dimensions and installation position of the

dishwasher.

1. Less than 5 mm between the top of dishwasher and cabinet and

the outer door aligned to cabinet.

Electrical, drain

and water supply

line entrances

Space between cabinet

bottom and oor

600 mm (for 60cm model)

450 mm (for 45cm model)

19

21

2. If dishwasher is in stalled at the corner of

the cabinet, there should be some space

when the door is opened.

NOTE:

Depending on where your electrical outlet

is, you may need to cut a hole in the opposite

cabinet side.

Step 3. Dishwasher installation steps

1. Affix the condensation strip under the work surface of cabinet.

Ensure the condensation strip is flush with edge of work surface.

(Step 2)

2. Connect the inlet hose to the cold water supply.

3. Connect the drain hose.

4. Connect the mains power cord.

5. Place the dishwasher into position. (Step 4)

6. Level the dishwasher. The rear feet can be adjusted from the front

of the dishwasher by turning the Philips screw in the middle of the

base of dishwasher use an Philips screw. To adjust the front feet,

use a flat screw driver and turn the front feet until the dishwasher

is level. (Step 5 to Step 6)

7. Install the furniture door to the outer door of the dishwasher.

(Step 7 to Step 10)

8. Adjust the tension of the door springs by using an Allen key

turning in a clockwise motion to tighten the left and right door

springs. Failure to do this could cause damage to your dishwasher.

(Step 11)

9. The dishwasher must be secured in place. Fix the side with

screws.

Dishwasher Cabinet

Door of

dishwasher

Minimum space of

50mm

20

Leht laadib ...

SENZ SD5011 OPPVASKMASKIN Omaniku manuaal

SENZ SD5011 OPPVASKMASKIN Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid