Samsung VR20R7250WC Kasutusjuhend

POWERbot

Quick reference guide

VR20R72**** Series

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 1 2020-01-13 오후 7:53:53

English-2

Parts list

1

Main

body

Basic

Parts

Remote

controller

Docking

Station

Batteries

(AAA type)

Quick reference

guide

Spare lter Power cord

Battery Charger Boundary markers Soft Action Brush /

Brush cover

Combo Brush /

Brush cover

 Accessories may differ depending on the models.

 Refer to page 9 for the installation of boundary markers.

 Battery Spec : Lithium-ion, 21.6V, 3600mAh, 12cell

 For VR20R726*** models, combo brush and soft action brush are provided.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 2 2020-01-13 오후 7:53:56

English-3

Safety information

2-1

• Before operating the appliance, please

read this manual thoroughly and retain it

for your reference.

• Because these following operating

instructions cover various models, the

characteristics of your vacuum cleaner

may differ slightly from those described

in this manual.

Caution/Warning symbols used

WARNING

Indicates that a danger of death or serious

injury exists.

CAUTION

Indicates that a risk of personal injury or

material damage exists.

Other symbols used

NOTE

Indicates that the following text contains

additional important information.

• For information on Samsung’s

environmental commitments

and product specic regulatory

obligations e.g. REACH (WEEE,

Batteries) visit: samsung.com/uk/

aboutsamsung/samsungelectronics/

corporatecitizenship/data_corner.html

Important safety instructions

When using an electrical appliance, basic

precautions should be observed, including

the following:

Read all instrucrions before using your

robot vacuum cleaner.

Unplug the charger / docking station

from outlet when not in use and before

conducting maintenance.

WARNING

To reduce the risk of re, electric shock,

or injury:

General

• Use only as described in this manual.

• Do not operate POWERbot or the

charger/docking station if it has been

damaged in any way.

• If the vacuum cleaner is not working as

it should, has been dropped, damaged,

left outdoors, or dropped in water, return

it to a customer care center.

• Do not handle the charger / docking

station or POWERbot with wet hands.

• Use only on dry, indoor surfaces.

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory

or mental capabilities or lack of

experience and knowledge if they have

been given supervision or instruction

concerning use of the appliance in a

safe way and understand the hazards

involved. Children shall not play with

the appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

• If the supply cord is damaged, it must

be replaced by the manufacturer or its

service agent or a similarly qualied

person in order to avoid a hazard.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 3 2020-01-13 오후 7:53:57

English-4

Safety information

2-2

Charger / Docking station

• Do not modify the polarized plug to t a

non-polarized outlet or extension cord.

• Do not use outdoors or on wet surfaces.

• Unplug the charger / docking station

from the outlet when not in use and

before servicing.

• Use only the charger / docking station

supplied by the manufacturer to

recharge.

• Do not use with a damaged cord or plug

or a loose power outlet.

• Do not pull or carry by the cord, use the

cord as a handle, close the door on the

cord, or pull the cord around sharp edges

or corners. Keep the cord away from

heated surfaces.

• Do not use extension cords or outlets

with inadequate current carrying

capacity.

• Do not unplug by pulling on the cord. To

unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as

they will explode at high temperatures.

• Do not attempt to open the charger /

docking station. Repairs should only be

carried out by a qualied customer care

center.

• Do not expose the charger / docking

station to high temperatures or allow

moisture or humidity of any kind to

come into contact with the charger /

docking station.

• Do not charge the non-rechargeable

batteries with the charger / docking

station.

• COMMISSION REGULATION (EU)

2019/1782

Ecodesign requirements for external

power supplies : www.samsung.com/

global/ecodesign_component

POWERbot

• Do not pick up hard or sharp objects

such as glass, nails, screws, coins, and

etc.

• Do not use without a lter in place.

When servicing the unit, never put

ngers or other objects into the fan

chamber in case the unit accidentally

turns on.

• Do not put any objects into openings.

Do not use with any openings blocked;

keep openings free of dust, lint, hair, and

anything that may reduce air ow.

• Do not pick up toxic materials (chlorine

bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning

or smoking, such as cigarettes, matches,

or hot ashes.

• Do not use to pick up ammable or

combustible liquids such as gasoline or

use in areas where they may be present.

Also do not use in:

– Locations with candles or desk lamps

on the oor.

– Locations with unattended res (re or

embers).

– Locations with distilled alcohol,

thinner, ashtrays with burning

cigarettes, etc.

• Do not use POWERbot in an enclosed

space lled with vapours given off by oil

based paint, paint thinner, moth proong

substances, ammable dust, or other

explosive or toxic vapours.

• Leaks from battery cells can occur

under extreme usage or temperature

conditions. If the liquid gets on

skin, wash quickly with water. If the

liquid gets into the eyes, ush them

immediately with clean water for a

minimum of 10 minutes. Seek medical

attention.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 4 2020-01-13 오후 7:53:58

English-5

Safety information

2-3

WARNING

Power related

• Please prevent any risk of electric shock

or re.

– Do not damage the power cord.

– Do not pull the power cord too hard or

touch the power plug with wet hands.

– Do not use a power source other than

100-240V~ and also do not use a

multi outlet to supply power to number

of devices at the same time. (Do not

leave the cord carelessly on the oor.)

– Do not use a damaged power plug,

power cord or loose power outlet.

• Clean dust or any foreign matters on the

pin and contact part of the power plug.

– There is a risk of electric shock or

malfunction.

Before use

• Do not use POWERbot near a heater or

combustible materials.

– Do not use powerbot near re or

ame such as a movable heater, a

candlelight, a desk lamp, a replace

etc. or in a place where combustible

materials such as gasoline, alcohol,

thinner etc. exist.

• Make sure there are no dangerous

objects around the POWERbot’s cleaning

area to prevent collision and unplug any

electric heaters or fans.

• The POWERbot is intended for household

use therefore do not use it in an attic,

basement, storage, industrial building,

out of indoor space, places with moisture

(such as bathroom, laundry), on the table

or shelves.

– The POWERbot can be damaged or

malfunction.

• Be sure POWERbot does not pass

through or touch any kind of liquids.

– The POWERbot can be severely

damaged and it may contaminate other

areas if the wheels pass through liquid.

• Attach the boundary markers to places

where the POWERbot may fall such as

the top of a staircase or a bannister to

prevent product damage and injury.

– Please keep the cliff sensor clean at all

times for safety.

• Do not spill any liquids on the docking

station.

– There is a risk of re or electric shock.

• Do not use the charger / docking station

for anything other than its intended

purpose.

– There is a risk of re or severe damage

to the docking station.

• Always keep the cliff sensor clean for

your safety.

In use

• If any abnormal sounds, smells or smoke

come from POWERbot, immediately shut

off the emergency switch at the bottom

of POWERbot and contact a service

center.

Cleaning and maintenance

• When power cord is damaged, contact

a service center to get it replaced by

certied repairman.

– There is a risk of re or electric shock.

• Please check with a Samsung Electronics

service center when exchanging

batteries.

– Using batteries from other products

can cause malfunction.

CAUTION

Before use

• Insert the dustbin before using POWERbot.

• Be careful with the followings for proper

automatic recharging.

– Always turn on the power of the

docking station.

– Install the docking station where the

POWERbot can nd it easily.

– Do not leave any object in front of the

docking station.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 5 2020-01-13 오후 7:53:59

English-6

Safety information

2-4

• When installing the docking station, do

not leave the cord carelessly on the oor

since POWERbot may get tangled by it.

• Do not use POWERbot on black colored

oors.

– The POWERbot may not be able to

operate normally.

• Do not pick up POWERbot by the dustbin

holder.

• Do not place any objects within 0.5 m

to both sides and 1 m to the front of the

docking station.

• Make sure the docking station’s charging

contact is not damaged or have any

foreign matters on it.

• Do not install the docking station in an

area with a dark oor.

– If the oor around the docking station

is dark, recharging is hindered.

• Move any obstacles that may disturb

POWERbot’s movement (such as children’s

indoor swing or slides) before cleaning.

• Do not use the POWERbot in a place

which is narrower than the turning

radius (0.5 m or less) of the POWERbot.

• To clean all areas of your house, open all

rooms and attach the boundary markers

on the places where the POWERbot

may get damaged such as a front door,

veranda, bathroom, and stairs for safety.

• For the very low areas where the

POWERbot may get stuck, attach the

boundary markers to prevent the

POWERbot from getting in.

• If a brush or brush cover is not assembled

correctly, scratches may occur on the

oor, or product malfunction may occur.

• Before operating the POWERbot, remove

the objects which could break such as

a frame, mirror, and porcelain items

so that the POWERbot works without

interruption.

In use

• Using POWERbot on thick carpet may

damage both POWERbot and the carpet.

– The POWERbot cannot pass over carpet

that is thicker than 1 cm.

• Do not use POWERbot on tables or other

high surfaces.

– There is a risk of damage if it falls.

• The POWERbot may bump into chair,

desk legs therefore move them away for

faster and efcient cleaning.

• When POWERbot is operating, do not lift

it up or carry it to another area.

• Do not hold by driving wheels of

POWERbot when carrying it to another

area.

• Do not put any objects on top

of POWERbot since it may cause

malfunction.

• Remove any large papers or plastic bags

immediately when using POWERbot

since they may block the intake.

• Do not aim the red pointer directly at

people or animals.

• Do not lie down around the POWERBOT

that is running.

– Your hair may be caught in the brush,

resulting in physical injury.

Cleaning and maintenance

• Prevent any damage to POWERbot by

complying the followings.

– Do not clean POWERbot by spraying

water directly onto it or use benzene,

thinner, acetone or alcohol to clean it.

• Do not disassemble or repair POWERbot.

This should only be done by a certied

repairman.

• Always keep the obstacle sensor and cliff

sensor clean.

– If foreign matter accumulates, sensors

may malfunction.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 6 2020-01-13 오후 7:54:01

English-7

3

Charging

Charge the POWERbot fully before using for the first time.

Please install the docking station in a place

where the oor is level and wall is straight.

How to turn on the

emergency switch

Hold the robot vacuum cleaner and

turn on the emergency switch without

pressing any buttons.

Check the charging status.

"

" will turn on according to

charging progress and "FULL" will

turn on when charging is complete.

When the product is purchased, the battery is not charged, so charging must initially be done manually.

0.5 m

1 m

0.5 m

Make sure the

charge pins on the

robot vacuum cleaner

and the charger are

aligned.

Ensure the power

cord is arranged

neatly next to the

wall.

Ú Install with the grain of wood oors.

Install the charger

where the robot vacuum

cleaner can easily nd

it.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 7 2020-01-13 오후 7:54:05

English-8

4-1

Using the robot vacuum cleaner

Starting Auto clean mode

The POWERbot moves and

automatically cleans the set

areas only once.

Stop cleaning:

Press and release the button

Starting Spot clean mode

Press and release this button.

The POWERbot cleans a

localized area intensely.

Recharging

You can command POWERbot

to recharge at the docking

station automatically while it is

cleaning by pressing this button.

Auto Clean Spot Clean Repeat clean

Manual Clean

Manual clean mode

can be selected by the

direction control buttons

of the remote controller.

Press the [

] on the

remote controller rst

and then press the [Start/

Stop ].

 POWERbot increases suction power in Spot clean and Point cleaning mode.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 8 2020-01-13 오후 7:54:07

English-9

Using the robot vacuum cleaner

4-2

About the boundary markers

To prevent the POWERbot from entering the following areas, attach

the boundary markers on the oor in the shape at an interval of

about 15cm.

About 15cm

Boundary

markers

About 5cm

About 15cm

Boundary

markers

where a raised spot is below 5cm where there is a slide, swing, replace or any

ammable substance or moisture.

Above 1.5cm

boundary

markers

Boundary

markers

where a threshold is above 1.5cm where there is risk of falling such as stairs, porches

or guardrails.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 9 2020-01-13 오후 7:54:09

English-10

1. Power

Turn POWERbot's power on/off

2. Recharging

Select to recharge POWERbot at the docking station

automatically

3. Start/Stop

Select to start or stop cleaning process

4. Auto clean

Select to clean all set areas only once and then

automatically return to the docking station

5. Spot clean

Select to clean a localized area intensely

6. Repeat clean

Select to clean repeatedly until the battery becomes

very low with indicator blinking

7. Turbo mode

Select to clean with the strongest suction power

8. Normal mode

Select to clean with moderate suction power

9. Quiet mode

Select to clean with lower operation noise

10. Sound

Select to set the voice guide

• Voice Guide (English)  Sound Effects  Mute

• Press and hold the sound button to change and set

a language.

11. Schedule / Cancel(3sec)

Refer to page 11

12. Clock

Refer to page 11

13. Remote control

Select to turn Wi-Fi function on or off

Using the robot vacuum cleaner

4-3

2

6

8

12

10

7

13

5

9

11

3 4

1

1_VR7200_Q_guide_EN_00827G-03_SB.indd 10 2020-01-13 오후 7:54:10

English-11

Setting time/schedule

Only Auto clean mode can be scheduled.

5

Setting the time

You must set the current time before using the One-time/daily schedule.

Setting the schedule

Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.

Setting complete

Start setting Select "Hour" Select "Minute"

Select "AM/PM"

Skip to previous,

next setting

Start setting

Setting complete Select "AM/PM" Select "Minute"

Select "One-time" or

"Daily" schedule

Select "Hour"

Skip to previous, next setting

Cancelling during setup

Setting will be canceled automatically when there's no input for

7seconds

Cancelling One-time/Daily schedule

When both One-time/

Daily schedule are set

or

Press for 3 sec. Select the schedule Cancel complete

When either One-time

or Daily schedule is set

Press for 3 sec.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 11 2020-01-13 오후 7:54:13

English-12

Cleaning and maintaining

You must turn off the emergency switch before cleaning POWERbot.

6-1

Dustbin

1

Press the button to

remove the dustbin

2

Remove the dustbin

cover

3

Remove dust in the

dustbin and cyclone

unit

'Click'

4

Detach the cyclone

unit from the dustbin

cover, and then wash

the dustbin and the

lter

5

Reassemble the

dustbin

6

Reinsert the dustbin

into the main body

until it clicks

1_VR7200_Q_guide_EN_00827G-03_SB.indd 12 2020-01-13 오후 7:54:15

English-13

Cleaning and maintaining

You must turn off the emergency switch before cleaning POWERbot.

6-2

Brush and Auto shutter tool

Soft Action Brush

Combo Brush

1

Remove the

brush cover

2

Remove the

brush

3

Clean the brush

Remove remaining dirt

on the soft action brush

with a wet tissue or a

dry cloth.

4

Clean the auto

shutter tool

5

Reassemble the brush

6

Reassemble the brush cover

For VR20R726*** models, check that the brush cover

is correct for the assembled brush.

 If a brush or brush cover is not assembled correctly after the maintenance work, scratches may occur on the

oor, or product malfunction may occur. Therefore, assemble them correctly by referring to the cleaning and

maintaining section of a user manual.

Information codes

 Refer to the user manual for steps to take for each Information code with mark on the display panel.

Brush design may differ depending on the model. Do not clean the brush with water.

1_VR7200_Q_guide_EN_00827G-03_SB.indd 13 2020-01-13 오후 7:54:19

English-14

Downloading the SmartThings App

f Download and install the SmartThings app from the markets (Google Play Store, Apple App Store, or

Samsung Galaxy Apps). To nd the app, use the keyword “SmartThings”.

NOTE

f SmartThings is incompatible with tablets and some mobile devices.

– Android 6.0 or later (at least 2GB of RAM) is recommended.

f iPad and some mobile devices may not be supported.

– iOS 10.0 or later / iPhone 6 or later is supported.

f Visit Play Store or App Store to see if your mobile device is compatible with SmartThings.

f The supported features are subject to change without any prior notice.

Setting up a Samsung account

f You must sign in to a Samsung account before using the SmartThings app.

f To set up a Samsung account, you can follow the directions provided by the SmartThings app.

f Or, if you have a Samsung smartphone, you can add your Samsung account in the setting app of your

smartphone. Then, it will automatically sign in to your Samsung account.

NOTE

f If you cannot complete the product registration, please take the following steps.

– Try the registration procedure again as you have directed by the pop-up messages.

– Conrm that the UPnP option of your wireless router is active, and then try the registration procedure again.

– Conrm that your wireless router is operating in wireless mode, and then try the registration procedure

again.

– If you have two or more POWERbots, turn off the other POWERbots, and then try to register your POWERbot

again.

– If there is any other wireless router that has the same SSID as your wireless router, the registration might be

failed.

f

Remote control and Wi-Fi indicator

On

Remote control is blocked. (The remote controller can still be

allowed.)

Off Remote control is allowed.

On The POWERbot is connected to the wireless router.

Off The POWERbot is trying to connect the wireless router.

 Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with Directive

2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

The ofcial Declaration of conformity may be found at http://www.samsung.com, go to Support > Search

Product Support and enter the model name.

Wi-Fi

Frequency range 2412 - 2472 MHz

Transmitter power(Max) 20 dBm

SmartThings App

The SmartThings App is only compatible with models that have a Wi-Fi

function.

7

1_VR7200_Q_guide_EN_00827G-03_SB.indd 14 2020-01-13 오후 7:54:21

English-15

Note

1_VR7200_Q_guide_EN_00827G-03_SB.indd 15 2020-01-13 오후 7:54:21

If you have any questions or comments relating to Samsung products,

please contact the SAMSUNG customer care center.

Country Contact Center Web Site

LITHUANIA 8-800-77777 www.samsung.com/lt/support

LATVIA 8000-7267 www.samsung.com/lv/support

ESTONIA 800-7267 www.samsung.com/ee/support

1_VR7200_Q_guide_EN_00827G-03_SB.indd 16 2020-01-13 오후 7:54:22

POWERbot

Kiirjuhend

VR20R72**** seeria

• Lugege suunised enne seadme kasutamist hoolikalt läbi.

• Kasutamiseks ainult siseruumides.

2_VR7200_Q_guide_ET_00827G-03_SB.indd 1 2020-01-14 오후 2:25:14

Eesti-2

Osade loend

1

Põhiseade

Põhiosad

Kaugjuhtimisseade

Dokkimisjaam

Akud

(AAA-tüüpi)

Kiirjuhend Varulter

Toitejuhe

Akulaadija Piirdemarkerid Kerge koristamise

hari / harja kate

Combo-hari / harja

kate

 Lisatarvikud võivad olenevalt mudelist erineda.

 Vt lk 15, kuidas paigaldada piirdemarkereid.

 Aku andmed: Liitiumioon, 21,6 V, 3600 mAh, 12 elementi

 VR20R726*** mudelitel on kaasas combo-hari ja kerge koristamise hari.

2_VR7200_Q_guide_ET_00827G-03_SB.indd 2 2020-01-14 오후 2:25:16

Eesti-3

Ohutusalane teave

2-1

• Enne seadme kasutamist lugege käesolev

kasutusjuhend hoolikalt läbi ja hoidke see

hilisemaks ülevaatuseks alles.

• Kuna järgnevad kasutussuunised hõlmavad

erinevaid mudeleid, võivad teie tolmuimeja

näitajad erineda veidi käesolevas juhendis

esitatutest.

KASUTATAVAD ETTEVAATUSABINÕUDE/

HOIATUSTE SÜMBOLID

HOIATUS

Tähistab surma- või tõsiste vigastuste ohtu.

ETTEVAATUST

Tähistab kehavigastuste või materiaalse kahju

ohtu.

TEISED KASUTATAVAD SÜMBOLID

MÄRKUS

Näitab, et järgnev tekst sisaldab olulist

lisateavet.

• Teabe saamiseks Samsungi

keskkonnakohustuste ja tootekohaste

regulatiivkohustuste, nt REACH-i (WEEE,

akud), kohta külastage veebilehte samsung.

com/uk/aboutsamsung/samsungelectronics/

corporatecitizenship/data_corner.html

Olulised ohutusalased suunised

Elektriseadme kasutamisel tuleb rakendada

üldiseid ettevaatusabinõusid, sh järgmisi.

LUGEGE KÕIK SUUNISED ENNE POWERboti

KASUTAMIST LÄBI.

Seadme mittekasutamisel ja enne hoolduse

teostamist eemaldage see pistikupesast.

HOIATUS

Tulekahju-, elektri- või vigastusohu

vähendamiseks järgige alltoodud

suuniseid.

ÜLDINE

• Kasutage seadet ainult selles

kasutusjuhendis kirjeldatud viisil.

• Ärge kasutage POWERboti ega akulaadijat/

dokkimisjaama, kui see on mis tahes viisil

kahjustunud.

• Kui tolmuimeja ei tööta nii, nagu peaks,

on maha kukkunud, õue jäetud, seda on

kahjustatud või vette pillatud, viige seade

klienditeeninduskeskusse.

• Ärge käsitsege akulaadijat/dokkimisjaama

ega POWERboti märgade kätega.

• Kasutage ainult siseruumis kuivadel

pindadel.

• Seadet võivad kasutada lapsed alates

8.eluaastast ning piiratud füüsiliste,

sensoorsete või vaimsete võimete või

vähese kogemuse või väheste teadmistega

inimesed, kui tagatud on järelevalve

või neid on juhendatud seoses seadme

ohutu kasutamisega ning nad mõistavad

kaasnevaid ohte. Lapsed ei tohi seadmega

mängida. Lapsed ei tohi teha puhastus- ega

hooldustoiminguid ilma järelevalveta.

• Kui toitejuhe on kahjustunud, peab

tootja, tema hooldustöötaja või sarnase

kvalikatsiooniga isik selle ohu vältimiseks

asendama.

2_VR7200_Q_guide_ET_00827G-03_SB.indd 3 2020-01-14 오후 2:25:17

Eesti-4

Ohutusalane teave

2-2

Akulaadija/dokkimisjaam

• Ärge muutke polariseeritud pistikut selle

sobitamiseks polariseerimata pistikupesa

või pikendusjuhtmega.

• Ärge kasutage õues ega märjal pinnal.

• Kui te akulaadijat/dokkimisjaama ei kasuta

või soovite seda hooldada, eemaldage see

pistikupesast.

• Kasutage laadimiseks ainult tootja tarnitud

akulaadijat/dokkimisjaama.

• Ärge kasutage, kui toitejuhe või pistik

on kahjustatud või pistikupesa lõdvalt

kinnitatud.

• Ärge tõmmake ega vedage seadet juhtmest,

kasutage juhet käepidemena, jätke juhet

ukse vahele ega tõmmake juhet ümber

teravate servade või nurkade. Hoidke juhe

eemal kuumadest pindadest.

• Ärge kasutage pikendusjuhet ega

pistikupesasid, mille võimsus pole piisav.

• Ärge eemaldage seadet vooluvõrgust

juhtmest tõmmates. Vooluvõrgust

eemaldamiseks võtke kinni pistikust, mitte

juhtmest.

• Ärge vigastage ega kuumutage akusid,

kuna need võivad kõrgetel temperatuuridel

plahvatada.

• Ärge proovige akulaadijat/dokkimisjaama

avada. Parandusi võivad teha ainult

volitatud hooldusmehaanikud.

• Ärge jätke akulaadijat/dokkimisjaama kõrge

temperatuuriga kohta ega laske mis tahes

laadi niiskusel akulaadija/dokkimisjaamaga

kokku puutuda.

• Ärge laadige akulaadijaga

mittetaaslaetavaid akusid.

• KOMISJONI MÄÄRUS (EL) 2019/1782

Välistoiteallikate ökodisaini nõuded :

www.samsung.com/global/ecodesign_

component

POWERbot

• Ärge imege seadmesse kõvasid või teravaid

esemeid, nt klaasi, naelu, kruvisid, münte

jms.

• Ärge kasutage seadet ilma ltrita. Ärge

pange seadme hooldamisel kunagi sõrmi

ega muid esemeid ventilaatorikambrisse,

sest seade võib kogemata sisse lülituda.

• Ärge pange avadesse esemeid. Ärge

kasutage seadet suletud avadega.

Hoidke avad vabana tolmust, kiududest,

juuksekarvadest ja muust, mis võib

õhuvoolu takistada.

• Ärge imege seadmega mürgiseid

aineid (kloorpleegiteid, ammoniaaki,

torupuhastusvahendeid jms).

• Ärge imege seadmega põlevaid või

suitsevaid esemeid, nt sigarette, tikke või

kuuma tuhka.

• Ärge kasutage seadet kergestisüttivate ega

põlevate vedelike (nt bensiin) koristamiseks

ega nende ainete läheduses.

Lisaks ärge kasutage toodet:

– Kohad, kus põrandal on küünlaid või

laualampe.

– Kohad, kus on järelevalveta tulease (tuli

või söed).

– Kohad, kus on destilleeritud alkoholi,

lahusteid, põlevate sigarettidega

tuhatoose jne.

• Ärge kasutage POWERboti suletud ruumis,

mis on täidetud õlivärvi, värvilahusti või

koitõrjevahendi aurude, kergestisüttivate

pulbrite või muude plahvatusohtlike või

toksiliste aurudega.

• Äärmuslikes tingimustes või ekstreemsel

temperatuuril kasutamisel võib aku hakata

lekkima. Kui akuvedelik satub nahale, peske

seda kiiresti veega. Kui vedelik satub silma,

loputage silmi kohe puhta veega vähemalt

10 minuti jooksul. Pöörduge arsti poole

2_VR7200_Q_guide_ET_00827G-03_SB.indd 4 2020-01-14 오후 2:25:17

Leht laadib ...

Samsung VR20R7250WC Kasutusjuhend

Samsung VR20R7250WC Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid