POINT PORLMW1 ROBOTGRESSKLIPPER Kasutusjuhend

Robotic Lawn Mower

PORLMW1

User Manual

POINT Robotic Lawn Mower.

POINT Robotgressklipper.

POINT Robottiruohonleikkuri.

Robotplæneklipper POINT.

RobotgräSklippare POINT.

4 - 33

34 - 63

64 - 93

94 - 123

124 - 153

IMPORTANT SAFEGUARDS:

IMPORTANT:

READ ALL INSTRUCTIONS BEFORE USE.

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING:

Basic safety precautions should always be observed

when using an electrical appliance to reduce the risk of

ﬁre, electrical shock or serious injury.

Warning Label Descriptions

Warning/Caution.

Dangerous voltage.

Keep bystanders at a safe

distance (at least 5m).

Always keep the lawnmower on

the ground when mowing.Tilting

or lifting the lawnmower maycause

stones to be thrown out.

Do not dispose of Li-Ion

battery with general

household waste.

Read the instruction manual.

Guaranteed Sound Power

Level

65

Beware of severing toes or hands.

Do not put hands or feet near a

rotating blade.

Caution: Wait until blades

stop rotat-ing when

switched o.

Do not ride on the mower

or allow children or pets

to do so.

Pick up sticks, stones and

foreign objects before using.

• Please read this manual carefully. Familiarise yourself thoroughly with the

controls and proper use of this machine. You should know how the machine

works and how to immediately switch it o.

• Never let children use this mower. Never let adults work with this mower if

not properly trained.

• Do not let any persons, especially small children, or pets near you while the

mower is in operation.

4

Personal Safety:

• Only use the mower on grass and lawns, as described in this manual.

• Keep out of reach of children and animals at all times.

• Do not use while there are other people, especially children, nearby.

• Stay alert, watch what you are doing and use common sense when operat-

ing the mower.

• Do not use the mower while you are tired or under the inﬂuence of drugs,

alcohol or medication. This may result in serious personal injury.

• Use protective personal equipment such as safety glasses, non-skid safety

shoes, sturdy gloves to reduce the risk of personal injury.

• Do not operate when barefoot or wearing open toed shoes.

• Dress appropriately. Do not wear loose clothing or jewellery and keep hair,

clothing and gloves away from moving parts.

• Do not use on excessively steep slopes.

• Never touch the rotating blade.

• Never operate the mower over gravel, as this risks ﬂicking stones.

• Check the area where the mower is to be used and remove any objects that

could jam or be thrown by the mower, such as stones and sticks.

• Avoid operating the mower on wet grass.

• Remove any dog mess before mowing.

• Visually check the cutting tools and their fasteners for any damage before

each use.

• To prevent imbalance, any damaged or worn-out parts should be replaced.

• Do not operate the mower if it is incomplete or has unauthorised modiﬁca-

tions.

• Keep all body parts, especially hands and feet, away from the blade at all

times.

• Warning, the blade will continue to move after the motor is switched o.

• Ensure that the blade has fully stopped before:

- clearing a blockage

- adjusting the cutting height

- lifting or carrying the mower

- tilting the mower to move

- checking or cleaning the mower

- carrying out any maintenance

• If the mower vibrates intensively, stop the motor fully and identify the

cause.

5

• The operator is responsible for accidents or hazards occurring to other

people at their property.

• This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities or lack of experience or

knowledge.

• Never modify the mower in any way.

• It is recommended to program the product for use during hours when the

area is free from activity, e.g. at night. But consider that certain animals,

e.g. hedgehogs and moles are active at night. They can potentially be

harmed by the product.

• The product must never be allowed to collide with persons or other living

creatures. If a person or other living creature comes in the way of the

product, it shall be stopped immediately.

• Do not put anything on top of the product or its charging station.

• Do not allow the product to be used with a defective guard, blade disc or

body. Neither should it be used with defective blades, screws, nuts or

cables. Never connect a damaged cable, or touch a damaged cable before

it is disconnected from the supply.

• Do not use the product if the STOP button does not work.

• Always switch o the product when it is not in use. The product can only

start when the correct PIN code has been entered.

• The product must never be used at the same time as a sprinkler. Use the

Schedule function so the product and sprinkler never run simultaneously.

• Metal objects in the ground (for example buried electrical cables) can

result in a stoppage. The metal objects can cause interference with the

loop signal which then can lead to a stoppage.

• Be aware that pets may dig or disrupt the perimeter wire, so check

regularly.

• We do not guarantee full

compatibility between the product and other types of wireless systems

such as remote controls, radio transmitters, hearing loops, underground

electric animal fencing or similar.

Electrical safety:

• Do not operate the mower in explosive atmospheres, such as in the

presence of ﬂammable liquids, gases or dust. Mowers can sometimes

create sparks, which may ignite the dust and fumes.

• Avoid body contact with earthed or grounded surfaces, such as pipes.

6

There is an increased risk of electric shock if your body is earthed or

grounded.

• In the event of a thunderstorm: To reduce the risk of damage to electrical

components in the product and the charging station, we recommend that

all connections to the charging station are disconnected (power supply,

boundary wire and guide wire) if there is a risk of a thunderstorm.

• Do not handle the charge station or the mower with wet hands.

• Regularly check the power supply and charge station cables for signs of

damage or ageing.

• Do not expose the mower to temperatures exceeding 80ºC, for example

leaving the mower in direct sunlight or in the hot boot of a car for

prolonged periods.

Battery safety:

• This product contains Li-Ion batteries. Do not incinerate batteries or

expose to high temperatures, as they may explode.

• After heavy use or in high temperatures the battery may become warm.

Allow the product to cool for 30 minutes before charging.

• Operation and storage temperature is 0-50 °C / 32-122 °F. Temperature

range for charging is 0-45 °C / 32-113 °F. Too high temperatures might

cause damage to the product.

Service:

• Check all visible ﬁxing screws and nuts, especially on the cutter disc, to

ensure they are tightened properly.

• The mower and its charge station should be periodically checked and

cleaned and kept free of debris and obstructions. Note that some garden

creatures such as spiders, insects, snails and slugs can nest or hibernate

within crevices of the mower. These can attract small creatures / rodents

that can damage the mower if not deterred.

• Before using the mower and after any impact, check for signs of wear and

damage and repair or replace as necessary.

• Use only genuine replacement parts. This will ensure that the safety of

the mower is maintained.

• Do not attempt to repair any damaged parts on the mower unless you are

qualiﬁed to do so.

7

Thank you for choosing Point

“Welcome to the Point family. We started Point to create sensible, easy to

use products that do a great job, and hope you get many years of trou-

ble-free performance from your new product.”

Robot mowers work by making regular small cuts of the grass to maintain

a set height. To do this they must be able to mow the grass multiple times

per day every day. This will keep the grass level constantly in check. As it is

cutting small amounts regularly the clipping will fall to the ground and are

not collected. Over time these small clippings will compost and add nitro-

gen to the lawn. Eventually this will leave the lawn looking more green and

lush and enhance the general health of the lawn.

What’s in the box

8

6

10

11

5

4

2

1

5

6

7

8

9

10

11

3

8 9

42 31

Boundary wire x150m

Boundary wire peg x150

Charge station groundscrew x4

Blades x9

Blade screw x10

Wire splicer x4

Power supply

Allen tool

Charging terminal x2

Charging station

Robot Mower

7

Preparing your lawn for the Robot Mower

9

Min 2m

Anti-clockwise

Min 30cm

Min 1.2m

Max 1.5cm

Min 35cm Charge Station

Min 1.2m

Boundary wire

The mower needs a full and complete

perimeter loop in order to operate. The

loop carries a weak electrical signal that

the mower uses to know where it is in

the garden.

Don't cross wires No right angles No acute anglesObtuse angles Curves

There is a handy ruler you can

press out of the carton that will

help you measure 35cm all

around your garden.

There may be parts of your garden which will be challenging or even

impossible for your Robot Mower. Your Robot Mower will not stray beyond

the boundary wire you must lay around your garden.

It will change direction on making contact with things like:

• Posts and poles (e.g. washing lines)

• Fences and walls around trees

But it will need to be kept away from:

• Dug borders

• Trees with exposed roots

• Flower beds

• Ponds and water features

• Excessively uneven terrain.

The cable must be kept taut and never be allowed to loop or cross over

itself. Ideally if ground is particularly uneven the wire can be buried up to

15mm deep and pegged down to secure. This can be achieved easily with a

manual edging tool. If this is not desired or possible then the wire should

be ﬁrmly pegged around the garden with pegs at a minimum of 1m inter-

vals, keeping the cable taut to avoid it being cut by the mower, more so at

corners and over uneven terrain.The cable should be positioned a minimum

of 35cm from the edge of the garden, as the mower will overlap the wire,

although it will not stray past it.

On corners the cable should not be laid at a sharp angle or right angle, but

curved or a series of obtuse angles. The mower can detect a signal from the

wire from as much as 20m away. It should be noted that due to this set up

some areas of the lawn will not get mowed such as outside the perimeter

edges. These can be maintained using a suitable grass trimmer.If the

ground where the wires are to be laid is particularly dry and the soil hard

from lack of rain, it will help to thoroughly water the garden before

attempting to lay your perimeter wire.

10

Rectifying or avoiding problem areas

Obstacles such as tree roots on lawn

Excessively uneven areas of lawn

11

If a tree root is

protruding into the

perimeter of your

cutting area it would

present a problem for

the mower.

One solution is to take

the perimeter around

the tree root, leaving

this area unmowed.

Alternatively, cut the

tree root back with a

saw and ﬁll any

resulting uneven

surface, then set the

perimeter over it.

A deep enough dip in

the surface of you

lawn will also present

problems, possibly

causing the mower’s

wheels to lose their

grip and skid.

If you don’t want to

avoid mowing this

area, it’s best to ﬁll it

with soil, compact it

down and re-seed it

with grass.

If your mower encounters particularly long grass

it may treat it as an obstacle as it could bump

the mower’s obstacle sensor. The grass needs to

be at a reasonable level before the Robot Mower

can function correctly.

If the area is on the

perimeter line this can

the be pegged out as

normal. If it is within

the mowing area it

should no longer be a

problem.

Installing the charge station

12

Find a location with access to

power, ensuring the mower can

leave the charge station in an

anti-clockwise direction. Don’t peg

the plate down yet.

The boundary wire

goes into the front (1)

of the charge station

and comes out at the

back (2).

Push the boundary

wire into the tube at

the front (1) of the

charge station.

It will emerge at the

rear of the unit (2).

The location of the charge station

should be ﬂat and secure, without

risk of movement, if placed next to a

border edge that is unstable it can

slump and cause the station to be

uneven, this will cause problems for

the mower when returning to charge.

Min 2m Min 30cm

The location must be within 5m of a safe

power source – either a weatherproof

outdoor electrical socket or an indoor

power point in a garage, for example.

Ensure a minimum of 2m straight

perimeter from the front of the

charge station, and 30cm straight

from the rear.

Safe power source

WARNING: Trailing wires are a trip hazard. Take care when choosing your location.

2

1

13

You will need to strip the plastic

sheath from the end of the wire

before connecting.

Twisting the exposed wires after

exposing helps ensure a good

connection.

Push the charge station hood

forward to uncover the wiring

terminals.

The charge stand has a hood at the

back (shown in grey) that hinges

forwards.

The sprung terminal will need lifting

to expose the hole, ensure the wire

is full inserted before releasing the

red terminal clip.

14

When you have completed your

perimeter cable it must return to

the charge station and be fed up

through the unit and plugs in at

the black terminal.

Pay attention to the cable ﬁttings

as there is a keyway orientation

detail to ensure correct connection.

Feed the power lead up through the

other side of the base station

Push the power cable into place

15

Then screw on the outer ring to

secure the cable in place and

prevent water ingress.

Push the cover back to it’s

original position to cover the

wires and connections from water

ingress.

Once the base station has been fully

wired it can be secured in place with

the four screws provided. Use the

allen key provided to screw them in

securely ensuring they are fully

inserted and ﬂush with the station

base. Protruding screws can hinder

the mower from locating correctly.

Making sure the power is switched o

at the socket, screw the two charging

rods into the holes just below the

cover of the base station.Note: This is

where the LED status indicator is

situated.

LED status indicator

Laying the perimeter cable

16

Keep the cable straight for at least

the ﬁrst 2m. This is to allow the

mower to return to the charging

stand with ease.

Place the pegs at intervals of about

1m on straight and even ground,

30cm to 50cm on bends and corners.

Uneven ground and obstacles will

require more pegs.

The perimeter wire must be kept

tight. If it is loose it may well end

up being cut by the mower as it

passes over it.

If the wire passes over a moderate

dip in the lawn, more pegs will be

required to keep the wire ﬁrmly

pegged at ground level, or it risks

being cut.

Min 2m Min 30cm

Operating the mower

17

Place the mower on the base

station with the wheels on the

grips and the two pins engaged

into the front of the mower. Note:

the mower will require to be

charged to at least 70% capacity

before it will leave its station.

Press the STOP button

This will ﬂip open the control

panel and LCD display cover.

Hold the power button (1) down for

three seconds to activate the LCD

display.

1

Control panel

Cutting height adjustment

18

1. Open the knob lid.

2. Cutting height can be

adjusted from 2.5cm to

5.5cm by rotating the

adjustment knob.

20 : 13 Oct . 19

Mowing

98%

Time, date,

battery, Wiﬁ

Status

RETURN button

OK button

UP, DOWN, LEFT,

RIGHT buttons.

A, B, C, D for PIN code.

STOP button:

Emergency stop and open

the control panel hatch

Power button:

Power on/o.

START button:

Start mowing.

HOME button:

Back to station.

Getting started:

Set the cutting height

The ﬁrst cut of the season or long thick wet grass will need the highest

setting (5.5cm). Gradually reduce to desired height once all ground has

been covered. This may take a few days or a few weeks. If the perimeter

wire is pegged to the surface of the garden rather than buried, it is a good

idea to let the wire “bed in” to the surface of the lawn, during which time it

is advisable to keep the mower on an elevated blade setting. NOTE during

ﬁrst few days of mowing the grass may look stripy or patchy where the

mower has covered /not covered. This is normal and will become even after

several days once the full lawn area has been mowed.

First time out

The control panel will ask for a pass code. The default PIN is AAAA

Pressing the start button and closing the ﬂap will cause the mower to start

a perimeter circuit after which it will begin randomly mowing the lawn.

First time out

The ﬁrst few mows will appear random and unﬁnished, this is normal. With

the multiple passes the mower makes over time, this will even out, and by

using zoning and spiral spot mowing a desirable eect can be achieved in

less time. These methods are explained on page 21.

New season mowing

Between mowing seasons when the mower is not operating (during winter

months) the grass can become unkempt and thickets emerge. On new

season setup review mowing pass and address any problem areas.

19

Status

Standby

Mowing

Spot Mow

Returning

Charging

Charge to work

Emergency stop

Error

Firmware update

Meaning

Mower is ready to work

Mower is mowing automatically

Mower is mowing spirally

Mower is going back to station

Mower is charging

Mower is charging and will continue program when charged

Mower is stopped manually

Mower cannot work

Firmware is updating

20

1. Press the power button for 3

seconds.

2. Enter the 4-letter PIN code.

The default PIN code is

“AAAA”.

3. The mower will now await

further instruction in standby

mode.

1. Press START button

2. Close the cover to startNote: If

the battery is below 70% charge,

the mower enters ‘charge to

work’ mode until it reaches 90%

charge. If lower than 30% the

mower returns to base station to

charge.

In standard mowing mode the

mower will proceed in a random

fashion around your garden,

changing direction each time it

reaches the perimeter wire.

1. Press the power button for 3

seconds.

Start mowing

Power on Power o

2

1 1

20 : 13 Oct . 19

Mowing

98%

Leht laadib ...

POINT PORLMW1 ROBOTGRESSKLIPPER Kasutusjuhend

POINT PORLMW1 ROBOTGRESSKLIPPER Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid