Bellman & Symfon Alarm Clock Pro BE1370 Kasutusjuhend

Kategooria
Äratuskellad
Tüüp
Kasutusjuhend

See käsiraamat sobib ka

In the box
BE1370 Pro alarm clock
BE1272 Bed shaker with sound
Power supply
4 x 1.2 V AAA NiMH batteries
Power and battery
Mains power
7.5 V DC / 1000 mA
External power supply unit
Backup batteries
4 x 1.2 V AAA NiMH rechargeable
batteries
Battery backup operating time
~ 24 h when fully charged
Battery backup charging time
~ 10 h from fully depleted
Output signals
Sound
100 dB @ 10 cm, 950 Hz – 3 kHz
Four high-intensity ashing LEDs
Bed shaker power: 2.0 – 4.0 VDC
The bed shaker emits a sound
Night light
Built in night light that guides you
back to bed with a mild blue light
Type: Electro Luminescent light (EL)
Night light timeout
On mains power: 1 hour
On backup battery: 15 minutes
Accessories
BE1270 Bed shaker
BE9250 Mobile phone sensor
Dimensions and weight
Height: 108 mm, 4.3"
Width: 121 mm, 4.7"
Depth: 92 mm, 3.6"
Weight: 390 g, 13.7 oz. incl. batteries
Display
Type: Twisted Nematic LCD
Adjustable backlight in 5 steps
Display timeout: 8 seconds
Alarm and snooze
Alarm timeout: 20 minutes
Decreasing snooze time interval
from 9 to 2 minutes
Snooze timeout: 20 minutes
Technical specications
Alarm clock Pro
Time dial
Flash and sound
on/o
Alarm indicatorAlarm on/o
Buttons and controls
Alarm dialSnooze
Wakeup Flashes Night lightSpeaker
2
3 4
Time format
1 – 3.5 mm external trigger input, 2 – Bed shaker
3 – Landline telephone, 4 – Power supply
1
The appearance may
dier with territory
BE1370
Getting started
1 Pull the battery tab on the bottom of the
alarm clock.
2 Connect the bed shaker on the back of the
alarm clock.
3 Connect the power supply to the alarm clock
and the mains outlet.
4 Tuck the bed shaker under the pillow or
mattress and place the alarm clock on the
bedside table.
Setting the time
Press the left dial and turn it to set hours.
To set minutes, press and turn the dial again.
Press once again to save your settings.
Setting the alarm
Press the right dial and turn it to set hours.
To set minutes, press and turn the dial again.
Press once again to save your settings.
Using the snooze and night light
Press the snooze button briey to snooze the alarm.
Press and hold the snooze button for 3 seconds to turn
on the night light. Press the button again to turn it o.
Activating the alarm
Press the alarm on/o button to activate the alarm.
The alarm indicator lights up in red. To turn o the
alarm, press the button again.
The appearance may
dier with territory
2
3
1
Alarm clock Pro
Alarm clock Pro
Troubleshooting
Alarm clock accessories
The alarm clock can be complemented with the following accessories:
BE9105 Telephone cord
Use it to connect the landline telephone to the alarm clock
RJ11 input and be alerted when the telephone rings.
BE9250 Mobile phone sensor
Connect it to the ext. trig. input and place it on the
display to be alerted by incoming calls or messages.
BE9024 Contact mat
Connect it to the ext. trig. input to be alerted when
your spouse leaves the bed.
If Try this
The alarm clock seems to be turned o
Check that the power supply is connected correctly, see Getting started.
Charge the backup batteries for a couple of hours.
The symbol on the clock face
starts to blink
The power supply is disconnected and the backup batteries are nearly depleted.
Connect the power supply and charge the backup batteries for a couple of hours.
A symbol appears on the clock face
The alarm clock detects no backup batteries. Pull the battery tab, see Getting
started. If the problem remains, check the backup batteries.
A symbol appears on the clock face
The ash is turned o. Press the ash and sound on/o button marked with
until the symbol disappears if you wish to turn it back on.
A symbol appears on the clock face
The sound is muted. Press the ash and sound on/o button marked with
until the symbol disappears if you wish to turn it back on.
The display is too bright or too dark or
I want it to be permanently lit
Press the button marked with repeatedly to adjust the intensity in 4 steps.
Choose step 5 that results in permanent backlight.
The bed shaker does not vibrate
Make sure it’s connected properly to the alarm clock, see Getting started.
The alarm volume is too low
The volume increases gradually and reaches over 100 dB.
Settings
Flash and sound on/o
Press the ash and sound on/o button marked with on the back of the alarm clock repeatedly to toggle between
the options. A symbol will appear on the clock face when the ash is turned o and a symbol when the sound is
muted.
Display backlight
Press the button marked with repeatedly to adjust the intensity in 4 steps. Step 5 results in permanent backlight.
Time format
Press the time format button marked with 12/24h on the back of the alarm clock to toggle between a 24h and a 12h setting.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Bellman & Symfon Alarm Clock Pro BE1370 Kasutusjuhend

Kategooria
Äratuskellad
Tüüp
Kasutusjuhend
See käsiraamat sobib ka