Zanussi WD1601INPT Kasutusjuhend

Bränd: Zanussi

Mudel: WD1601INPT

Kategooria: Pesumasinad

Tüüp: Kasutusjuhend

WASHER-DRYER

STIRALWNO-SUﬁILNAÅ MAﬁINA

TVÄTT-/TORKMASKIN

PESU-/KUIVAUSKONE

WD 1601

RUKOVODSTVO PO ÈKSPLUATACII

INSTRUCTION BOOKLET

BRUKSANVISNING

KÄYTTÖOHJE

132982880

FIN

RUS

132982880rus.qxd 14-3-2006 8:31 Pagina 1

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use recycled paper.

132982880GB.qxd 15/03/2006 11.38 Pagina 2

ENGLISH

Contents

Maintenance 27

Door seal 27

Bodywork 27

Detergent dispenser drawer 27

Drain pump 27

Water inlet filter 28

Emergency emptying out 28

The dangers of freezing 28

Something not working? 29-30

Warnings 4-5

Disposal 5

Tips for environmental protection 5

Technical specifications 6

Installation 7

Unpacking 7

Positioning 7

Water inlet 7

Water drainage 8

Electrical connection 8

Your new washer-dryer 9

Description of the appliance 9

Door locked pilot light 9

Detergent dispenser drawer 9

Use 10

Control panel 10

Controls 10-15

Washing hints 16

Sorting the laundry 16

Temperatures 16

Before loading the laundry 16

Maximum loads 16

Laundry weights 16

Removing stains 16

Detergents and additives 17

Drying hints 18

International wash code symbols 19

Operating sequence 20-23

Washing only 20-22

Drying only 23

Automatic washing and drying 23

Washing programmes 24

Special programmes 25

Timed drying 26

132982880GB.qxd 15/03/2006 11.38 Pagina 3

Installation

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this appliance

must be carried out by a qualified electrician.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the

feet and the floor.

Use

• Never touch the machine while standing on a wet

floor or being barefoot.

• This appliance is designed for domestic use. It

must not be used for purposes other than those for

which it was designed.

• Only wash and dry fabrics which are designed to

be machine washed and dried. Follow the

instructions on each garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects such

as coins, safety pins, pins and screws can cause

extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing

garments in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

• If you use a liquid detergent with a dispenser which

has to be placed directly in the drum, remember to

remove this dispenser before drying.

Warnings

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes and

during the drying cycle the door glass may get hot.

Do not touch it!

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• Make sure that children or pets do not climb into

the drum.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

132982880GB.qxd 15/03/2006 11.38 Pagina 4

ENGLISH

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it shall be handed over to

the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment

and human health, which could otherwise be caused

by inappropriate waste handling of this product. For

more detailed information about recycling of this

product, please contact your local city office, your

household waste disposal service or the shop where

you purchased the product.

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded, but do not overload it (see maximum moad

on page 30).

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature, so saving energy.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

• The machine will consume less energy if the

laundry is adequately spun before being dried.

132982880GB.qxd 15/03/2006 11.38 Pagina 5

Technical specifications

DIMENSIONS Height 85 cm

Width 60 cm

Depth 58 cm

WASHING DRYING

MAXIMUM LOAD Cotton 5.5 kg 2.75 kg

Synthetics 3 kg 2 kg

Delicates 3 kg -

Woollens 2.0 kg -

SPIN SPEED 1600 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 0.05 MPa

Maximum 0.80 MPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

132982880GB.qxd 15/03/2006 11.38 Pagina 6

ENGLISH

Installation

Unpacking

All transit bolts and packing must be removed

before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

1. Using a spanner, unscrew and remove the rear

right-hand bolt and lay the machine on its back,

taking care not to squash the hoses. This can be

avoided by placing one of the corner packing

pieces between the machine and the floor.

2. Remove the polystyrene block from the bottom of

the machine and release the two plastic bags.

3. Carefully remove the right-hand bag (1) then the

left-hand bag (2) by pulling them towards the

centre of the machine.

4. Set the machine upright and remove the two

remaining bolts from the back.

5. Pull out the three plastic spacers from the holes

into which the bolts were fitted.

6. Plug the open holes with the plugs wchich you

will find in the envelope containing the instruction

booklet.

P0020

P0256

P1066

P1068

P0255

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with a 3/4" thread.

Do not use already employed hoses.

The other end of the inlet hose which connects to the

machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks.

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

P0021

P1088

P1051

132982880GB.qxd 15/03/2006 11.38 Pagina 7

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked. Run it along the

floor; only the part near the drainage point must be

raised.

P1118

P0022

Electrical connection

This machine is designed to operate on a 220-230 V,

single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to comply

with the above safety precaution.

Should the appliance power supply cable

need to be replaced, this should be carried

out by our Service Centre.

Please ensure that when the appliance is

installed the power supply cable is easily

accessible.

132982880GB.qxd 15/03/2006 11.38 Pagina 8

ENGLISH

Your new washer-dryer

This new washer-dryer, which is fitted with the Jet system, paited Zanussi, meets all modern needs for

effective treatment of laundry with low water, energy and detergent consumption.

• The possibility of selecting the temperature, spin speed and all the options offered by this machine gives

you truly “customised” washing.

• The DELAY START option allows you to delay starting of the wash programme to any time of day, so

allowing you for instance to make use of overnight economy electricity tariffs.

• The programme progress display shows the programme steps selected and the programme phase which

is running.

• The special wool programme with its new delicate wash system treats your woollens with extreme care.

• The balance control device ensures the machine is stable during the spin.

• The drying programmes will give your wash that soft, relaxed feel whatever the weather.

1 Detergent dispenser drawer

2 Control panel

3 Door locked pilot light

4 Drain filter

5 Adjustable feet

Door locked pilot light

It stays on during the whole programme indicating

that the door is locked.

When the light goes out, the door can be opened

(see page 48).

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Description of the appliance

P0260

132982880GB.qxd 15/03/2006 11.38 Pagina 9

Use

6 7 891011

Control panel

1. Funktion of MEMORY buttons

There are 4 Memory buttons at your disposal to

memorize and recall the four washing programmes

that are used more frequently.

•

Choose the washing programme as described on

page 20.

•

Choose the drying programme or NON-STOP

programme (automatic washing and drying) as

described on page 23.

•

Start the programme pressing the Start/Pause

button .

•

Press only one of the Memory buttons, until the

control light above the button lights up.

•

The control light will go out after about 5 seconds;

the programme is memorized.

Modification

If you want to modify a programme already

memorized, you can operate, with the appliance on,

by pressing the relevant buttons

(Fabrics ,

Temperatur , Spin speed ,

Options). Now you must press the Start/Pause

button to start the machine.

Memorization

Finally press the corresponding Memory button until

the control light lights up.

When the light goes out, the new programme is

memorized.

A memorized programme can be recalled pressing

the corresponding Memory button.

•

Switch the machine on

•

Press the Memory button 1/2/3 or 4. The lights

above the programme buttons indicate the chosen

programme.

•

Start the programme pressing the Start/Pause

button .

Note

If you press a Memory button to which no

programme corresponds, the display will show the

message “Err” for 2 seconds.

When you start the machine for the first time, it can

happen that there are some programmes already

memorized. This is due to an inspection test carried

out in the factory.

2 ON/OFF - CANCEL button

This button has 2 functions:

Recall

132982880GB.qxd 15/03/2006 11.38 Pagina 10

ENGLISH

Pressing the ON/OFF button the machine is

switched on and off; the machine can be

programmed when three dashes are blinking on the

display.

If you want to cancel a programme already started,

you must switch the machine off. The chosen

programme is cancelled in this way.

3 FABRIC button

After having switched the machine on, press this

button to set the type of fabric to be washed.

You can choose the following types of fabrics:

WHITE/COLOURED COTTON

SYNTHETIC

DELICATE

WOOL

HAND WASH

•

Press this button repeatedly until the light

corresponding to the type of fabric to be washed

lights up.

•

At the same time the machine suggests a

programme for the selected type of fabric. If the

programme suggested is acceptable, you can start

the machine; if instead you want to modify the

temperature or the spin speed, press the

corresponding buttons.

•

Choosing the type of fabric, the display will show

the duration of the chosen programme. The

indication of the time blinks until the programme is

started.

Important!

The FABRICS button must not be depressed

whenyou select the special programmes

•

SOAK

•

MINI

•

RINSES

•

DRAIN

•

SPIN

•

DRYING

Cancellation of a programme

Main switch

4 TEMPERATURE button

Pressing this button you can modify the washing

temperature proposed by the machine.

The light shows the set temperature.

On the position the washing is carried out with

cold water.

5 SPIN SPEED button

Pressing this button you can reduce the maximum

spin speed proposed by the machine according to

the type of fabric, or you can choose the option

“rinse hold”. The light shows the set position.

The maximum speed is automatically adjusted

according to the type of fabric.There are the

following speeds available:

cotton

700/900/1200/ max 1600 rpm

synthetic/wool/hand wash

700/ max. 900 rpm

delicate/mini

700 rpm

Choosing the position “rinse hold", the laundry

remains in the water of the last rinse. At the end of

the programme the light corresponding to “rinse

hold” remains on, to show that the water has still to

be drained before you can open the door.

A zero will light up on the display.

RINSE HOLD

Spin

132982880GB.qxd 15/03/2006 11.38 Pagina 11

There are 3 possibilities to drain the water:

•

Choose the “Drain” programme.

The water is drained without spin.

•

Press only the Start/Pause button .

The machine drains the water and carries out the

spin cycle provided for the type of fabric.

•

Select the spin speed

Select the desired spin speed with the

corresponding button and press the Start/Pause

button .

Note

The option (RINSE HOLD) can be selected

also with the programme (MINI) and

(RINSES).

Attention!

If the water is not drained, the machine empties

itself after 18 hours.

The RINSE HOLD option cannot be selected withthe

NON-STOP programme washing and drying.

Important! Pressing at the same time

theTEMPERATURE and SPIN SPEED

buttons, the sound signal activated by the

programme buttons and at the end of the programme

is switched off.

If you want to spin some items that you have washed

by hand proceed as follows:

•

switch the machine on by pressing the ON/OFF

button .

•

select the spin speed .

•

depress the Start/Pause - button to start the

machine .

6 OPTIONS button

With this button several functions can be added to

the set washing programme, or this one can be

modified to save energy.

You can choose the followings options:

Prewash – Quick wash – Ekonomy

Spin programme

Choose the desired function pressing the

corresponding button. The light shows the selected

function.

The machine carries out a prewash at 30°C max.;

the washing programme will last for about 20

minutes longer. With the programmes for cotton and

synthetic fabrics the prewash will end with a short

spin, while with the delicate programme there is only

the draining of the water. It is used for very soiled

laundry.With the wool and “Hand wash” programme

this function cannot be chosen.

With this function the washing cycle of the cotton,

synthetic and delicate programmes is shortened. It is

used for slightly soiled laundry. With the wool and

“Hand wash” programme this function cannot be

chosen.

You can choose this option only in the following

programmes:

White cotton 95°C

Coloured cotton 60°C

Synthetic 60°C

The temperature is reduced automatically from 95°

to 67°C or from 60° to 45°C. To balance the

temperature reduction, the duration of the washing

cycle is slightly extended. In this way it is possible to

save energy obtaining the same washing results. It is

used for normally soiled laundry.

Note

The “PREWASH

, QUICK WASH

, ECONOMY

“ functions cannot be selected at the same time.

One rules out the other.

By means of the same button you can select the

following special programmes:

The Soak programme is a separate programme; it is

started, after you have selected it, by pressing the

START/PAUSE button . It is used for heavily

soiled laundry.The washing temperature is 30°C and

the programme ends with "rinse hold" (water in tub).

To drain the water press the START/PAUSE button.

Soak

SPECIAL PROGRAMMES

Ekonomi

Quick wash

Prewash

132982880GB.qxd 15/03/2006 11.38 Pagina 12

ENGLISH

Note

•

If the laundry is not taken out within 18 hours, the

machine will drain the water automatically.

•

At the end of the soak time, that is set by the user,

and after the draining of the water, a zero appears

on the display. Now you can select the washing

programme or recall a memorized programme by

operating the MEMORY buttons; pressing the

START/PAUSE button the programme will start .

This programme can be used particularly for briefly

used and not very soiled laundry and for laundry

stained with sweat. It is possible to set a washing

temperature of 60° Cmax. Not suitable for wool and

for items bearing the “hand wash” label.

With this programme it is possible to rinse and spin

hand-washed items, especially delicate and synthetic

fabrics and some types of woollen fabrics that cannot

be machine washed. 3 rinses and the final spin at

the maximum speed are carried out. The spin speed

can be reduced pressing the "Spin" button. .

This programme can be used to drain the water of

the last rinse in the programmes with “Rinse hold”

option. Select the programme pressing the

corresponding button and then press the

START/PAUSE button. .

7 AUTOMATIC DRYING button

By means of this button you can choose the required

degree of drying for cottons and synthetics:

= Extra dry (cottons)

= Store dry (cottons and synthetics)

= Iron dry (cottons)

The corresponding pilot light illuminates.

The drying time is automatically adjusted by the

machine: the laundry will be dried to the selected

degree of dryness.

Drain

Rinses

MINI (Freshen up)

8 TIMED D

RYING

button

If you wish to carry out a timed programme instead

of an electronic programme push this button; the

light corresponding to the selected fabric (cotton or

synthetic) illuminates.

To commutate from “synthetic” to “cotton” press the

button for 2 seconds until the corresponding light

turns on.

To select the drying time push the button until the

drying time you want appears in the display. Every

time you push the button the time increases by 5

minutes.

For COTTON you can select a drying time from

10 minutes to 2 hours and 10 minutes (2.10).

For SINTHETIC you can select a time from 10

minutes to 1 hour and 40 minutes (1.40).

9 Display

The display shows the following pieces of

information:

Machine ready to receive data – Duration of

washing programme – Delayed start – Drying

time – Incorrect option selection – Alarm code

After having switched on the machine by pressing

the ON/OFF button , 3 dashes on the display

showthat the machine can be programmed.

Now you can set the programme.

- - -

Machine ready to receive data

132982880GB.qxd 15/03/2006 11.38 Pagina 13

After having set the programme, the display shows

the duration in hours and minutes (ex.. 2.05).

The time refers to the maximum load for each

programme. The figures blink until the programme is

started pressing the START/PAUSE button .

After the start, the indication of the remaining time

decreases by one unit every minute.

Many elements determine the duration of the

programme, e.g. the wash load, the temperature of

the incoming water, the formation of lather, etc.

These elements are recorded by the electronic

system and the indication of the remaining time is

updated accordingly.

The end of the programme is shown on the display

with a blinking zero.

The delayed start that was set with the button (11) is

shown on the display (max 24 hours).

The delay time value will decrease by one unit every

hour.

The selected drying time is displayed in minutes or

hours and minutes.

Drying time

Delayed start

2.05

Duration

After starting the programme, the remaining time

isupdated every minute.

If an option which is not compatible with the set wash

programme is selected, the message Err is

displayed.

This is also indicated by three sound signals and by

the corresponding lights that blink for about 2

seconds.

In case of breakdowns of the appliance, these are

indicated on the display with a special code, very

useful for the user and for the technical assistance,

e.g. “E20” (see pages 29-30).

10 START/PAUSE button

This button has 3 functions:

Start – Pause – Drain

E20

Alarm code

Incorrect option selection

132982880GB.qxd 15/03/2006 11.38 Pagina 14

ENGLISH

Pressing this button the selected programme is

started.

If the delayed start has been set, the countdown will

start.

Now on the display the duration of the programme or

the hours of the delayed start stops blinking.

Pressing this button a programme already started

can be interrupted in any moment; pressing again

the button, the programme restarts. During the

pause, the indication on the display is blinking.

Pressing this button::

•

the water of the programme “SOAK” is drained

•

the water in the programmes with "RINSE

HOLD”option is drained and a final spin is

carried out.

11 DELAY START button

With this button it is possible to delay the starting of

the programme by up to 24 hours max.

•

Switch the machine on

•

Select the programme

•

Set the delayed time

•

Press the START/PAUSE button. .

Now the countdown of the set time begins (it

decreases by one unit every hour).

During these hours it is possible, when the Pause

button is pressed, to open the door and to add

someclothes.

Depress Start button after closing the door. At the

end of the set time the programme starts.

Setting the delayed start

Drain

Pause

Start

•

Press the START/PAUSE button .

•

Press the DELAY START button repeatedly

until the desired time appears on the display. If the

setting has to be cancelled, press the button once,

the display will show the indication “0h” (0 hours).

•

Press again the START/PAUSE button ; when

the set time expires, the programme starts.

How to open the door

1. With the machine switched off

With power supply switched off (with the machine

off) it is possible to open the door in any moment. To

open it, pull forwards the handle A.

2. How to open the door during a programme

The door can be opened also during a programme

provided the following conditions exist:

•

The temperature of the water must be lowerthan

40°C.

•

The level of the water must be low

•

There must not be a spin or drying in progress.

Press the START/PAUSE button .

The “door locked” light B placed above the door

handle indicates the closing of the door. Only when

the light goes out, it is possible to open the door.

3. Emergency opening

If door opening is absolutely necessary and the

conditions described at point 2 do not exist, switch

the machine off by pressing the ON/OFF button

After about 3 minutes it is possible to open the door

(pay attention to the water level and temperature in

the drum).

P0353

Altering the delayed start

132982880GB.qxd 15/03/2006 11.38 Pagina 15

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95°

for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

60° for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g.

underwear).

(cold) for delicate items (e.g. net curtains),

30°-40°

mixed laundry including synthetic fibres

and woollens.

The wool wash cycle of this machine has

been approved by Woolmark for the

washing of machine washable Woolmark

products provided that the garments are

washed according to the instructions on

the garment label and those issued by the

manufacturer of this washing machine.

Licence N. M9605

Before loading the laundry

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towelling towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

132982880GB.qxd 15/03/2006 11.38 Pagina 16

ENGLISH

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees”

of hardness. Information on hardness of the water

in your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

Degrees of water hardness

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

Level Characteristic

Degrees

German

°dH

French

°T.H.

soft

medium

hard

very hard

0- 7

8-14

15-21

more than

0-15

16-25

26-37

more than

132982880GB.qxd 15/03/2006 11.38 Pagina 17

Drying hints

As a dryer, the machine works on the condensation

principle.

Therefore, the water tap must be open and the

drain hose must drain water into a sink or into

the drain pipe, even during the drying cycle.

Load

Warning:

Loads of washed laundry exceeding these values

must be divided before being dried, otherwise

poor results will be obtained.

Garments not suitable for drying

• Particularly delicate items such as synthetic

curtains, woollen and silk, garments with metal

inserts, nylon stockings, bulky garments such as

anoraks, bedcovers, quilts, sleeping bags and

duvets must not be machine dried.

• Garments padded with foam-rubber or materials

similar to foam-rubber must not be machine dried;

they represent a fire hazard.

• Also, fabrics containing residues of setting lotions

or hair sprays, nail solvents or similar solutions

must not be machine dried in order to avoid the

formation of harmful vapours.

Drying symbols on garment labels

Always look at the garment label to check whether

garments can be machine dried.

The following symbols refer to drying:

Machine drying is usually possible

Normal drying (normal temperature)

Gentle drying (reduced temperature)

Do not machine dry

Duration of the drying cycle

The drying time can vary according to

• the final spin speed;

• the required degree of drying (extra dry, store dry

or iron dry);

• the type of laundry;

• the size of load.

The usual drying times for the timed programmes are

indicated in the programme chart. As you become

more familiar with the appliance, you will discover

the drying times that best suit your needs according

to the various type of fabric. It is a good idea to make

a note of these times.

Fibre residue

After drying fluffy fabrics, such as new towels, it is

advisable to perform the rinse programme to be sure

that any residue that may remain in the tub is

completely removed and does not stick to garments

dried afterwards.

After each drying cycle the filter should be

checked and cleaned.

Additional drying

Should the laundry still be too wet at the end of the

programme, set another short drying cycle.

Warning! To prevent the formation of creases or

shrinking of fabrics, avoid excessive drying.

max. load

(dry weight)

2,75 kg

2 kg

Linen and cottons

Synthetics

Sort of laundry

132982880GB.qxd 15/03/2006 11.38 Pagina 18

ENGLISH

International wash code symbols

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

Energetic wash

Delicate wash

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

Hand wash Do not

wash

at all

Bleaching Bleach in cold water Do not bleach

Ironing Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning Dry cleaning

in all solvents

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

pure alcohol

and R 113

Do not

dry clean

Drying Flat On the line On clothes

hanger

Tumble dry

high

temperature

low

temperature

Do not

tumble dry

132982880GB.qxd 15/03/2006 11.39 Pagina 19

4. Switch the machine on

Press the ON/OFF button to switch the machine

on; the display will show three blinking dashes.

5. Choose the programme

Press the FABRICS button until you choose the

desired programme/fabric; the corresponding light

will light up.

6. Choose the temperature

Press the button until the desired washing

temperature illuminates.

- - -

P0226

P0223

Operating sequence

Wash only

Before washing your first load of laundry, we

recommend that you run a cotton cycle at 95°C, with

the machine empty, to remove any manufacturing

residue from the drum and tub. Pour half a measure

of detergent in the compartment of the detergent

drawer and start the machine.

Choosing the programme

There are 3 possibilities to select theprogramme:

• with the programme buttons

• with the Memory buttons

• with the special programmes

The setting of the programme is carried out as

indicated below.

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you wish to carry out the PREWASH or SOAK

pour detergent into the appropriate compartment

marked .

3. Measure out the additives

Pour any liquid additives, to soften or starch the

laundry, in the compartment .

Do not exceed the MAX level.

P0004

Setting with the programme buttons

132982880GB.qxd 15/03/2006 11.39 Pagina 20

Leht laadib ...

Zanussi WD1601INPT Kasutusjuhend

Bränd: Zanussi

Mudel: WD1601INPT

Kategooria: Pesumasinad

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

svenska: Zanussi WD1601INPT Användarmanual
English: Zanussi WD1601INPT User manual

Zanussi WD1601INPT Kasutusjuhend

Zanussi WD1601INPT Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid