Simplex SafeLINC 4020-0160 Installation & Operation Instructions

Installation, Setup

& Operating

Instructions

SafeLINC

TM

Fire Panel

Internet Interface ( FPII )

579-349

Rev. H

i

Specifications and other information shown were current as of publication and are subject to

change without notice.

SafeLINC, TrueAlarm, Simplex, and the Simplex logo are trademarks of Tyco International

Ltd. and its affiliates and are used under license.

Microsoft is a registered trademark of Microsoft Corporation.

Windows is a trademark of the Microsoft Corporation.

All other logos and product names are trademarks or registered trademarks of their respective

companies.

Copyright and Trademarks

Copyright

Trademarks

ii

READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation

manual. These instructions must be followed to avoid damage to this product and associated

equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX

®

PRODUCT THAT APPEARS DAMAGED- Upon unpacking

your Simplex product, inspect the contents of the carton for shipping damage. If damage is

apparent, immediately file a claim with the carrier and notify an authorized Simplex product

supplier.

ELECTRICAL HAZARD - Disconnect electrical field power when making any internal

adjustments or repairs. All repairs should be performed by a representative or authorized agent of

your local Simplex product supplier.

EYE SAFETY HAZARD – Under certain fiber optic conditions, the optical output of this device

may exceed eye safety limits. Do not use magnification (such as a microscope or other focusing

equipment) when viewing the output of this device.

STATIC HAZARD - Static electricity can damage components. Handle as follows:

• Ground yourself before opening or installing components.

• Prior to installation, keep components wrapped in anti-static material at all times.

In the event of equipment malfunction, a representative of your local Simplex product supplier

should perform all repairs. It is the responsibility of users requiring service to report the need for

service to your local Simplex product supplier.

Cautions and Warnings

Cautions and

Warnings

Service

Requirements

iii



Introduction to the SafeLINC FPII .................................................................. 1

Introduction .................................................................................................. 1

Overview ...................................................................................................... 1

Requirements ............................................................................................... 2

SafeLINC FPII Card Illustration .................................................................. 2

SafeLINC FPII Card Specifications ................................................................. 3

General Temperature/Humidity Requirements ............................................ 3

Specific Temperature/Humidity Requirements ............................................ 3

Power Requirements .................................................................................... 3

Configuring the SafeLINC FPII Card .............................................................. 4

Overview ...................................................................................................... 4

Setting Communications .............................................................................. 4

Setting Computer Port Protocol (CPP) Functionality .................................. 4

Setting the Baud Rate and Address .............................................................. 5

Mounting the SafeLINC FPII Card .................................................................. 7

Overview ...................................................................................................... 7

4100U/4100ES Mounting ............................................................................ 7

4010ES Mounting ....................................................................................... 8

4100/4120 Mounting .................................................................................... 9

4020 Mounting ........................................................................................... 10

SafeLINC FPII Field Wiring.......................................................................... 11

Overview .................................................................................................... 11

4100U/4100ES/ 4010ES-Style Wiring ...................................................... 11

4100/4120 Legacy Wiring ......................................................................... 12

4020-Style Wiring ...................................................................................... 13

LED Indicators ............................................................................................... 14

Interpreting LED Indications ..................................................................... 14

Adding the SafeLINC FPII to the FACP via the Programmer ....................... 16

Overview .................................................................................................... 16

Using the DOS-Based Programmer ........................................................... 16

Using the Windows-Based Programmer .................................................... 21

Connecting a PC to the SafeLINC FPII Diagnostic & Configuration Port .... 26

Connecting SafeLINC FPII Card to a PC .................................................. 26

Configuring a Terminal Emulation Program ............................................. 26

Checking for Duplicate IP Addresses ........................................................ 26

Using the Boot Menu ..................................................................................... 28

Completing the MIS/IT Configuration Worksheet .................................... 28

Entering Data from the MIS/IT Configuration Worksheet ........................ 29

Starting Up the SafeLINC FPII ...................................................................... 31

Logging In as an Administrator ................................................................. 31

The Home Page .............................................................................................. 32

Overview .................................................................................................... 32

The Home Page .......................................................................................... 32

The Administration Menu .......................................................................... 32

Login Accounts .............................................................................................. 33

Overview .................................................................................................... 33

Setting Up a New User Account ................................................................ 33

Adding/Editing a User Account ................................................................. 33

Changing the Administrator Password ....................................................... 34

Email Configuration....................................................................................... 35

Overview .................................................................................................... 35

Configuring SafeLINC FPII Email ............................................................ 35

Disabling Outgoing Email ......................................................................... 36

Configuring the Email Health Status Check .............................................. 36

Customizing Event Messages .................................................................... 36

Understanding Email Event Notification ................................................... 37

Contents

iv

Security Settings ............................................................................................ 38



Overview .................................................................................................... 38

Description of Security Settings ................................................................ 38

Customize Links ............................................................................................ 40

Setting Up the Home and User Links Pages .............................................. 40

Updating Firmware ........................................................................................ 41

Overview .................................................................................................... 41

Firmware Update Procedure ...................................................................... 41

Summary ........................................................................................................ 43

Viewing a Summary of Administrative Changes ....................................... 43

General Operations ........................................................................................ 44

The System Menu ...................................................................................... 44

Checking the System Status ....................................................................... 44

Viewing System, Card, and Point Reports ..................................................... 46

Overview .................................................................................................... 46

Viewing TrueAlarm Service Reports ......................................................... 46

Viewing TrueAlarm Status Reports ........................................................... 46

Viewing Point Summaries ......................................................................... 46

Viewing Card Summaries .......................................................................... 47

Viewing the SafeLINC FPII/Host Panel Summary .................................... 47

Viewing Alarm and Trouble Logs ............................................................. 47

Basic Reports ................................................................................................. 48

Overview .................................................................................................... 48

Report Items ............................................................................................... 48

MIS/IT Configuration Worksheet .................................................................. 49

1

This document can be used with FPII installed on the 4100ES, 4100U, 4100, 4010ES, 4120, and

4020-Series Fire Alarm Systems. Table 1 lists SafeLINC FPII Product ID numbers (PIDs) and the

compatible Fire Alarm Control Panel (FACP) PIDs.

Table 1. SafeLINC FPII & Compatible FACP PIDs

SafeLINC FPII Product ID Compatible FACP Product ID

4100-6060 Any 4100U/4100ES FACP Product ID

4010-9913 Any 4010ES FACP Product ID

4120-0160 4120-8001, -8010, -8201, -8210, -8511,

-8601, -8700, -8701, & -8721

4100-0160 4100-8001, -8010, -8201, -8210, -8511,

-8601, & -8701

4020-0160 4020-8001

The Fire Panel Internet Interface (SafeLINC FPII) is a module that interfaces to a 4100ES, 4100U,

4100, 4010ES, 4120, or 4020 Fire Alarm Control Panel (FACP), and it provides the following:

• Ability to access FACP data using the Internet Explorer (IE) 5.0+ web browser in conjunction

with a Win98, ME, NT, or 2000 operating system.

• Ability to send email messages for prioritized event notification and scheduled email of

Dirty/Excessively Dirty detector status information. (The SafeLINC FPII functions as an

information kiosk that’s accessible via the Internet rather than as a remote annunciator.)

• Ability to email reports for TrueAlarm

®

Sensor Status, TrueAlarm Sensor Service, and

historical logs (fire alarm, Priority 2 alarm, trouble, and supervisory) on demand or via a

schedule (weekly, bi-weekly, or monthly).

This publication describes how to:

• Install the SafeLINC FPII card.

• Configure the SafeLINC FPII for operation on your local network.

• Configure the SafeLINC FPII Administrative Account.

• Configure the SafeLINC FPII to send email.

• Use the SafeLINC FPII.

Notes:

• It is strongly recommended that both your operating system and web browser contain

the latest patch updates.

• The SafeLINC FPII is for ancillary use only and does not provide any fire alarm or

burglary function other than reporting of system status.

Introduction to the SafeLINC FPII

Introduction

Overview

2

To use the SafeLINC FPII properly, you must meet the following requirements:

• Win98, ME, NT, or 2000 Operating System

• Internet Explorer (IE) 5.0+ web browser

• FACP System Firmware: V9.02.02, 10.61, 11.03, or greater

• 4100ES, 4100U, 4100, 4010ES, 4120, or 4020 FACP

Figure 1 depicts the SafeLINC FPII card.

NETWORK

LINK ACT

L7

Figure 1. The SafeLINC FPII Card

Introduction to the SafeLINC FPII, Continued

Requirements

SafeLINC FPII Card

Illustration

SafeLINC FPII TROUBLE

LED

(

LED3

)

NETWORK LINK LED

(LED1)

SafeLINC FPII SLAVE CARD

BAUD RATE / ADDRESS DIP

SWITCH (SW4)

4100 POWER & COMMS

CONNECTOR

(NON-4100U/4100ES or

4010ES) (P1)

4020 POWER & COMMS

CONNECTOR (P2)

4100ES /4100U/4100/4010ES/4120

COMMS & 4020 (RUI) COMMS DIP

SWITCH (SW2)

CPP / MX JUMPERS

(P14, P10)

(P15, P11)

DIAGNOSTICS &

CONFIGURATION PORT

(P9)

4100U/4100ES/4010ES

POWER & COMMS

PDI CONNECTOR

(reverse side)

ETHERNET

CONNECTION (J1)

NETWORK ACTIVITY LED

(LED2)

3

The following general temperature/humidity specifications apply to the SafeLINC FPII card.

The equipment operates normally with ambient temperatures outside the cabinet from 32° to

120° F (0° to 49° C), inclusive.

The equipment operates normally under non-condensing humidity conditions up to 93% relative

humidity at 90° F (32° C).

Effective Operating Temperature Range ……. 32° to 120° F (0° C to 49° C), assuming 41° F

(5° C) rise in FACP cabinet.

Effective Operating Humidity Range ……….. 10 to 93% relative humidity (±2%)

non-condensing at 90° F (32° C) (±2°).

SafeLINC FPII power is supplied from system FACP 24 V. On-board power supplies include

5 V, 3.3 V, and 2.5 V with each supply powered from the 24 V FACP connection.

Maximum Battery Standby Current Draw ….. 115 mA Maximum on 24 V rail (Worst Case).

SafeLINC FPII Card Specifications

General

Temperature/Humidity

Requirements

Specific

Temperature/Humidity

Requirements

Power Requirements

4

This section describes how to configure the SafeLINC FPII card using DIP switches and jumpers.

DIP switch SW2 is used to set the SafeLINC FPII card’s communications to either 4020/RUI-

Style, 4100/4120 Legacy, or 4100U/4100ES/4010ES-Style communications. Set the DIP switch

according to the illustration.

IMPORTANT: For proper communications, recheck the SW2 settings before applying

power.

FigureTag FD9-349-01

1

8

7

6

5

4

3

2

1

8

7

6

5

4

3

2

1

8

7

6

5

4

3

2

Figure 2. SW2 Switch Settings

Use P10, P11, P14 and P15 to set the SafeLINC FPII card’s incoming protocol. Verify that P10,

P11, P14 and P15 are all set to Positions 1 and 2. You should not have to change the positions

because they are set to Positions 1 and 2 by default from the factory.

P10, P11, P14, P15: Positions 1-2: CPP (default from factory).

1 2 3 Positions 2-3: Reserved for future use.

Configuring the SafeLINC FPII Card

Overview

Setting

Communications

Setting Computer

Port Protocol (CPP)

Functionality

ON

OFF

ON

OFF

4020/RUI-Style

Communications:

4100/4120 Legacy

Communications:

1

2

3

ON

OFF

4100U/4010ES-Style

Communications:

5

The device address is set via DIP Switch SW4, which is a bank of eight switches. From left to

right (see Figure 3 below), these switches are designated as SW4-1 through SW4-8. The function

of these switches is as follows:

• SW4-1. This switch sets the baud rate for the internal communications line running between

the card and the FACP CPU. Set this switch to ON for 9600 baud communication.

• SW4-2 through SW4-8. These switches set the card’s address within the FACP. Refer to

Table 2 for a complete list of the switch settings for all of the possible card addresses.

FigureTag FD9-349-02

1

8

7

6

5

4

3

2

Figure 3. SW4 Switch Settings

Continued on next page

Configuring the SafeLINC FPII Card, Continued

Setting the Baud

Rate and Address

ON

OFF

DIP Switches SW4-2 through

SW4-8 set the Card Address.

Figure 3 shows an Address of 3.

Baud Rate. Switch

(SW4-1) Must Be Set to

ON (9600 Baud)

6

Table 2. Card Addresses

Configuring the SafeLINC FPII Card, Continued

Setting the Baud

Rate and Address

Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8

1 ON ON ON ON ON ON OFF 61 ON OFF OFF OFF OFF ON OFF

2 ON ON ON ON ON OFF ON 62 ON OFF OFF OFF OFF OFF ON

3 ON ON ON ON ON OFF OFF 63 ON OFF OFF OFF OFF OFF OFF

4 ON ON ON ON OFF ON ON 64 OFF ON ON ON ON ON ON

5 ON ON ON ON OFF ON OFF 65 OFF ON ON ON ON ON OFF

6 ON ON ON ON OFF OFF ON 66 OFF ON ON ON ON OFF ON

7 ON ON ON ON OFF OFF OFF 67 OFF ON ON ON ON OFF OFF

8 ON ON ON OFF ON ON ON 68 OFF ON ON ON OFF ON ON

9 ON ON ON OFF ON ON OFF 69 OFF ON ON ON OFF ON OFF

10 ON ON ON OFF ON OFF ON 70 OFF ON ON ON OFF OFF ON

11 ON ON ON OFF ON OFF OFF 71 OFF ON ON ON OFF OFF OFF

12 ON ON ON OFF OFF ON ON 72 OFF ON ON OFF ON ON ON

13 ON ON ON OFF OFF ON OFF 73 OFF ON ON OFF ON ON OFF

14 ON ON ON OFF OFF OFF ON 74 OFF ON ON OFF ON OFF ON

15 ON ON ON OFF OFF OFF OFF 75 OFF ON ON OFF ON OFF OFF

16 ON ON OFF ON ON ON ON 76 OFF ON ON OFF OFF ON ON

17 ON ON OFF ON ON ON OFF 77 OFF ON ON OFF OFF ON OFF

18 ON ON OFF ON ON OFF ON 78 OFF ON ON OFF OFF OFF ON

19 ON ON OFF ON ON OFF OFF 79 OFF ON ON OFF OFF OFF OFF

20 ON ON OFF ON OFF ON ON 80 OFF ON OFF ON ON ON ON

21 ON ON OFF ON OFF ON OFF 81 OFF ON OFF ON ON ON OFF

22 ON ON OFF ON OFF OFF ON 82 OFF ON OFF ON ON OFF ON

23 ON ON OFF ON OFF OFF OFF 83 OFF ON OFF ON ON OFF OFF

24 ON ON OFF OFF ON ON ON 84 OFF ON OFF ON OFF ON ON

25 ON ON OFF OFF ON ON OFF 85 OFF ON OFF ON OFF ON OFF

26 ON ON OFF OFF ON OFF ON 86 OFF ON OFF ON OFF OFF ON

27 ON ON OFF OFF ON OFF OFF 87 OFF ON OFF ON OFF OFF OFF

28 ON ON OFF OFF OFF ON ON 88 OFF ON OFF OFF ON ON ON

29 ON ON OFF OFF OFF ON OFF 89 OFF ON OFF OFF ON ON OFF

30 ON ON OFF OFF OFF OFF ON 90 OFF ON OFF OFF ON OFF ON

31 ON ON OFF OFF OFF OFF OFF 91 OFF ON OFF OFF ON OFF OFF

32 ON OFF ON ON ON ON ON 92 OFF ON OFF OFF OFF ON ON

33 ON OFF ON ON ON ON OFF 93 OFF ON OFF OFF OFF ON OFF

34 ON OFF ON ON ON OFF ON 94 OFF ON OFF OFF OFF OFF ON

35 ON OFF ON ON ON OFF OFF 95 OFF ON OFF OFF OFF OFF OFF

36 ON OFF ON ON OFF ON ON 96 OFF OFF ON ON ON ON ON

37 ON OFF ON ON OFF ON OFF 97 OFF OFF ON ON ON ON OFF

38 ON OFF ON ON OFF OFF ON 98 OFF OFF ON ON ON OFF ON

39 ON OFF ON ON OFF OFF OFF 99 OFF OFF ON ON ON OFF OFF

40 ON OFF ON OFF ON ON ON 100 OFF OFF ON ON OFF ON ON

41 ON OFF ON OFF ON ON OFF 101 OFF OFF ON ON OFF ON OFF

42 ON OFF ON OFF ON OFF ON 102 OFF OFF ON ON OFF OFF ON

43 ON OFF ON OFF ON OFF OFF 103 OFF OFF ON ON OFF OFF OFF

44 ON OFF ON OFF OFF ON ON 104 OFF OFF ON OFF ON ON ON

45 ON OFF ON OFF OFF ON OFF 105 OFF OFF ON OFF ON ON OFF

46 ON OFF ON OFF OFF OFF ON 106 OFF OFF ON OFF ON OFF ON

47 ON OFF ON OFF OFF OFF OFF 107 OFF OFF ON OFF ON OFF OFF

48 ON OFF OFF ON ON ON ON 108 OFF OFF ON OFF OFF ON ON

49 ON OFF OFF ON ON ON OFF 109 OFF OFF ON OFF OFF ON OFF

50 ON OFF OFF ON ON OFF ON 110 OFF OFF ON OFF OFF OFF ON

51 ON OFF OFF ON ON OFF OFF 111 OFF OFF ON OFF OFF OFF OFF

52 ON OFF OFF ON OFF ON ON 112 OFF OFF OFF ON ON ON ON

53 ON OFF OFF ON OFF ON OFF 113 OFF OFF OFF ON ON ON OFF

54 ON OFF OFF ON OFF OFF ON 114 OFF OFF OFF ON ON OFF ON

55 ON OFF OFF ON OFF OFF OFF 115 OFF OFF OFF ON ON OFF OFF

56 ON OFF OFF OFF ON ON ON 116 OFF OFF OFF ON OFF ON ON

57 ON OFF OFF OFF ON ON OFF 117 OFF OFF OFF ON OFF ON OFF

58 ON OFF OFF OFF ON OFF ON 118 OFF OFF OFF ON OFF OFF ON

59 ON OFF OFF OFF ON OFF OFF 119 OFF OFF OFF ON OFF OFF OFF

60 ON OFF OFF OFF OFF ON ON

7

The SafeLINC FPII card can be mounted to the 4100ES, 4100U, 4100, 4010ES, 4120, or 4020

systems. The mounting in each case is different. Refer to the appropriate topic in this section,

depending on which fire alarm system you are using.

The SafeLINC FPII assembly is to be mounted on the PDI in a 4100U/4100ES expansion bay

(Figure 4). The card should be mounted to the left-most position on the PDI connector as Figure 4

illustrates.

Use the connector on the backside of the SafeLINC FPII card to connect to the bay as shown in

Figure 4, below.

Figure 4. 4100U/4100ES Mounting

Mounting the SafeLINC FPII Card

Overview

4100U/4100ES

Mounting

SafeLINC FPII

Card

Standoffs

#6 Screws

Washers

PDI Connector

(reverse side)

PDI

8

In the case of a 4010ES panel, it can be used inside a one-bay or two-bay panel. The FPII would

be mounted on the top-bay or bottom-bay PDI card (Figure 5).

Figure 5. 4010ES Wiring

Mounting the SafeLINC FPII Card, Continued

4010ES Mounting

The SafeLINC FPII

may mount in the left-

most vertical block pair

in a single-bay box or

any open vertical block

pair in a two-bay box.

Top-Bay PDI on a One or

Two-Bay 4010ES Panel

Expansion Bay PDI in a Two-Bay

4010ES Panel

9

In either a 4100 or a 4120 system, the SafeLINC FPII takes up two 2-inch slots. Secure the

assembly to the mounting rails as shown below.

Mount the card to the left-most position on the mounting rails (if possible).

IMPORTANT: The 637-591 Bracket must be mounted to the 4100/4120 mounting rails

before the SafeLINC FPII card is mounted.

Figure 5. 4100/4120 Mounting

Mounting the SafeLINC FPII Card, Continued

4100/4120 Mounting

637-591 Bracket must be

mounted to rails first

SafeLINC FPII

Card

#6 Screws

Washers

10

In a 4020 system, the SafeLINC FPII assembly mounts onto either the back plate or hat bracket as

shown below.

Mount the card to the left-most position on the mounting rails (if possible).

IMPORTANT: If a hat bracket is installed, the SafeLINC FPII assembly must be

mounted to the hat bracket.

Figure 6. 4020 Mounting

Mounting the SafeLINC FPII Card, Continued

4020 Mounting

Hat bracket (optional)

SafeLINC FPII assembly

must be mounted to hat

bracket if applicable

#6 Screws

Washers

Back Plate

677-604

Bracket

(Bracket must be mounted

to hat bracket or back

plate before SafeLINC FPII

assembly is attached to it)

11

This section contains the complete field wiring drawings for the SafeLINC FPII card.

The SafeLINC FPII card can connect to 4100U/4100ES and 4010ES PDI boards as shown below.

Unlike the 4100/4120 and 4020, a harness is not required for power and communications.

Figure 7. 4100U/4100ES and 4010ES-Style Wiring

SafeLINC FPII Field Wiring

Overview

4100U/4100ES/

4010ES-Style Wiring

PDI Connector P16

PDI Board

J1:

Connect to Corporate LAN. All equipment

comprising Corporate LAN is to be UL-Listed

Information Technology Equipment.

Use EIA/TIA-568a CAT-5-Compliant Cable, or

better.

Either Unshielded (UTP) or Shielded (STP)

Cable is Acceptable.

Terminate Cable with RJ-45 Connector (if not

already terminated by MIS/IT).

P9:

SafeLINC FPII Diagnostic

and Configuration Port (Not

Connected During Normal

Operation)

Use 733-794 Download

Cable to Interface SafeLINC

FPII to PC/Laptop.

12

NETWORK

LINK ACT

L7

The SafeLINC FPII card can connect to 4100/4120 Legacy (non-4100U/4100ES) motherboards as

shown below.

FigureTag FD9-349-03

Figure 8. 4100/4120 Legacy Wiring

SafeLINC FPII Field Wiring, Continued

4100/4120 Legacy

Wiring

HARNESS

734-008

TIC

P1

Connectors with

White Wire Go to P3

(

Power

)

Connectors with

Blue Wire Go to P2

(Comms)

Harness

734-078

P1

SafeLINC

FPII Card

4100 Motherboard

P9:

SafeLINC FPII Diagnostic

and Configuration Port

(Not Connected During

Normal Operation)

Use 733-794 Download

Cable to Interface

SafeLINC FPII to

PC/Laptop.

J1:

Connect to Corporate LAN. All equipment

comprising Corporate LAN is to be UL-Listed

Information Technology Equipment.

Use EIA/TIA-568a CAT-5-Compliant Cable,

or better.

Either Unshielded (UTP) or Shielded (STP)

Cable is Acceptable.

Terminate Cable with RJ-45 Connector (if not

already terminated by MIS/IT).

13

The SafeLINC FPII card can connect to a 4020 as shown in Figure 9. This illustration shows the

SafeLINC FPII card connected to MAPNET Interface Board via Harness 733-693 and the 4020

Power & Comms Connector P2. This is an example of one connection to the 4020. If the

MAPNET Interface Board is unavailable for power and communications, you will need to connect

to another 4020 board. Instead of the MAPNET Interface Board, you also can connect Harness

733-693 from the SafeLINC FPII’s P2 connector to the Standard Slave Card (P6, P7), Power

Supply Interface Board (P2, P3), 8-Point I/O Board (P9, P10), 2120/RS232 Interface Board (P8,

P9), or Network Option Board/Repeater Card (P11, P12). See the 4020 Interconnection Diagrams

(841-906) for more information.

TB1

P2P1 P3

MAPNET INTERFACE BD

565-241

OR

2120/RS232

INTERFACE BD

565-224

OR

NETWORK OPTION BD/

REPEATER CARD

565-411 OR -518

OR

CONTACT CLOSURE

DACT 742-015

OR

PHYSICAL BRIDGE MODEM

MODULE STYLE 4

636-765

OR

SDACT

742-059

Figure 9. 4020-Style Wiring

SafeLINC FPII Field Wiring, Continued

4020-Style Wiring

4020 Power & Comms

Connector P2

Power &

Comms

Harness

733-693

P9:

SafeLINC FPII Diagnostic

and Configuration Port (Not

Connected During Normal

Operation)

Use 733-794 Download

Cable to Interface SafeLINC

FPII to PC/Laptop.

J1:

Connect to Corporate LAN. All equipment

comprising Corporate LAN is to be UL-Listed

Information Technology Equipment.

Use EIA/TIA-568a CAT-5-Compliant Cable,

or better.

Either Unshielded (UTP) or Shielded (STP)

Cable is Acceptable.

Terminate Cable with RJ-45 Connector (if

not already terminated by MIS/IT).

14

The SafeLINC FPII contains 3 LEDs to provide user status indication. (See Figure 1 for location

of LEDs.) LED 3, colored yellow, provides trouble status information using blink codes. The

summary of the blink codes (trouble codes) appears in Table 3 below.

LEDs 1 and 2 are used to monitor both the integrity of the network connection (Link Status, Green

LED = LED1) and whether network activity is present (Network Activity, Red LED = LED2) to

and from the SafeLINC FPII.

Table 3. Blink Codes for LED 3 (Yellow LED)

LED Blink Code Definition (See below for more details)

LED3

(Yellow LED)

Short-Short-Short

Network Down (Network Status Check

Trouble)

Short-Long-Short

Network Disconnected (Network Link

Integrity Trouble)

Short-Long-Long Internal Network Loop-Back Trouble

Short-Short-Long Email Link Trouble

Long-Long-Long

RUI/4100 Comms or Slave Core

Trouble

Long-Short-Short RAM Test Trouble

Long-Short-Long FLASH Test Trouble

Long-Long-Short EEPROM Test Trouble

Notes:

Short = ½-second duration

Long = 1-second duration

Rest between multiple troubles = 2 seconds

Rest between repeating trouble list = 3 seconds.

Network Down (Network Status Check) - Used as a diagnostic to determine if the SafeLINC

FPII can see out onto the connected network, the SafeLINC FPII periodically checks the

customer’s configured gateway (as was configured on the boot prompt) to verify that the

SafeLINC FPII can see the gateway. However, it does not guarantee that the SafeLINC FPII is

fully operational on the network to which it is connected. The frequency of this check is

determined by configuring the Network Status Check under Administration: Security Settings.

Network Disconnected (Network Link Integrity) - The SafeLINC FPII examines the Link

Integrity Bit on the PHY to determine if the Ethernet Cable is plugged into the SafeLINC FPII. If

the cable is plugged into both the Hub/Router/Switch and the SafeLINC FPII, the Green Link

LED (LED1) will light up. There is no configurable option on the web pages for this diagnostic

feature. The SafeLINC FPII checks this at the same interval as configured for Network Down

(Network Status Check Trouble).

Internal Local Loop-Back - Testing the integrity of the onboard connection from the

microprocessor to the Ethernet Connector, the SafeLINC FPII takes an outgoing test packet and

re-routes it internally to the PHY and then back to the microprocessor. This test determines if the

PHY & MAC are operational. Between this test and the Network Disconnected Test (Network

Link Integrity Test), you are reasonably sure that the SafeLINC FPII can communicate on the

network as long as it has been configured properly.

Email Link – Periodically testing for the presence of the email server to see if it is able to accept

messages, this diagnostic logs into the SMTP server and logs out without sending any email

messages. This testing interval is defined under SafeLINC FPII: SafeLINC FPII Administration:

Email Configuration as the Email Health Status Check Interval. This test also checks that the PC

on which the server is running is operational as well as checking that the SMTP server is actually

running, too. Although this test does not check that the remaining network is operational, it does

reasonably ensure that any email message can be delivered to the server successfully.

Continued on next page

LED Indicators

Interpreting LED

Indications

Leht laadib ...

Simplex SafeLINC 4020-0160 Installation & Operation Instructions

See käsiraamat sobib ka

Simplex SafeLINC 4020-0160 Installation & Operation Instructions

teistes keeltes

Muud dokumendid