Dell Inspiron 5735 Omaniku manuaal

Bränd: Dell

Mudel: Inspiron 5735

Kategooria: Märkmikud

Tüüp: Omaniku manuaal

See käsiraamat sobib ka

Inspiron M731R

Inspiron M731R

Owner’s Manual

Computer model: Inspiron 5735

Regulatory model: P17E

Regulatory type: P17E003

book.book Page 1 Wednesday, October 2, 2013 3:11 PM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Trademarks used in this text: Dell

™

, the DELL logo, and Inspiron

™

are trademarks of Dell Inc.;

Microsoft

, Windows

, and the Windows start button logo are either trademarks or registered

trademarks of Microsoft Corporation in the United States and/or other countries;

Bluetooth

is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under

license.

2013 - 10 Rev. A00

book.book Page 2 Wednesday, October 2, 2013 3:11 PM

Contents | 3

Contents

Before Working Inside Your Computer 9

Before You Begin 9

Recommended Tools 9

Safety Instructions 10

After Working Inside Your Computer 11

Removing the Battery 12

Procedure 12

Replacing the Battery 13

Procedure 13

Removing the Optical Drive 14

Prerequisites 14

Procedure 14

Replacing the Optical Drive 16

Procedure 16

Postrequisites 16

Removing the Keyboard 17

Prerequisites 17

Procedure 17

Replacing the Keyboard 19

Procedure 19

Postrequisites 19

Removing the Base Cover 20

Prerequisites 20

Procedure 20

Replacing the Base Cover 21

Procedure 21

Postrequisites 21

book.book Page 3 Wednesday, October 2, 2013 3:11 PM

4 | Contents

Removing the Memory Module(s) 22

Prerequisites 22

Procedure 22

Replacing the Memory Module(s) 23

Procedure 23

Postrequisites 23

Removing the Hard Drive 24

Prerequisites 24

Procedure 24

Replacing the Hard Drive 26

Procedure 26

Postrequisites 26

Removing the Coin-Cell Battery 27

Prerequisites 27

Procedure 27

Replacing the Coin-Cell Battery 28

Procedure 28

Postrequisites 28

Removing the Palm Rest 29

Prerequisites 29

Procedure 29

Replacing the Palm Rest 32

Procedure 32

Postrequisites 32

Removing the Wireless Card 33

Prerequisites 33

Procedure 33

Replacing the Wireless Card 35

Procedure 35

Postrequisites 35

book.book Page 4 Wednesday, October 2, 2013 3:11 PM

Contents | 5

Removing the I/O Board 36

Prerequisites 36

Procedure 36

Replacing the I/O Board 37

Procedure 37

Postrequisites 37

Removing the System Board 38

Prerequisites 38

Procedure 39

Replacing the System Board 42

Procedure 42

Postrequisites 43

Removing the Fan 44

Prerequisites 44

Procedure 44

Replacing the Fan 45

Procedure 45

Postrequisites 45

Removing the Heat Sink 46

Prerequisites 46

Procedure 46

Replacing the Heat Sink 47

Procedure 47

Postrequisites 47

Removing the Hard-Drive Interposer Board 48

Prerequisites 48

Procedure 48

Replacing the Hard-Drive Interposer Board 49

Procedure 49

Postrequisites 49

book.book Page 5 Wednesday, October 2, 2013 3:11 PM

6 | Contents

Removing the Speakers 50

Prerequisites 50

Procedure 51

Replacing the Speakers 52

Procedure 52

Postrequisites 52

Removing the Display Assembly 53

Prerequisites 53

Procedure 54

Replacing the Display Assembly 55

Procedure 55

Postrequisites 55

Removing the Display Bezel 56

Prerequisites 56

Procedure 57

Replacing the Display Bezel 58

Procedure 58

Postrequisites 58

Removing the Display Hinges 59

Prerequisites 59

Procedure 60

Replacing the Display Hinges 61

Procedure 61

Postrequisites 61

Removing the Display Panel 62

Prerequisites 62

Procedure 63

Replacing the Display Panel 64

Procedure 64

Postrequisites 64

book.book Page 6 Wednesday, October 2, 2013 3:11 PM

Contents | 7

Removing the Camera Module 65

Prerequisites 65

Procedure 66

Replacing the Camera Module 67

Procedure 67

Postrequisites 67

Removing the Power-Adapter Port 68

Prerequisites 68

Procedure 69

Replacing the Power-Adapter Port 70

Procedure 70

Postrequisites 70

Flashing the BIOS 71

book.book Page 7 Wednesday, October 2, 2013 3:11 PM

8 | Contents

book.book Page 8 Wednesday, October 2, 2013 3:11 PM

Before Working Inside Your Computer | 9

Before Working Inside Your Computer

Before You Begin

CAUTION: To avoid losing data, save and close all open files and exit all open

programs before you turn off your computer.

1 Save and close all open files, exit all open programs, and turn off your computer.

• Windows 8: Point to the lower or upper-right corner of the screen to open the

Charms sidebar and click Settings→ Power→ Shut down.

• Windows 7: Click Start → Shut down.

NOTE: If you are using a different operating system, see the documentation

of your operating system for shut-down instructions.

2 After the computer shuts down, disconnect it from the electrical outlet.

3 Disconnect all cables — such as power and USB cables — from your computer.

4 Disconnect all peripherals from your computer.

Recommended Tools

The procedures in this document may require the following tools:

• Phillips screwdriver

• Plastic scribe

book.book Page 9 Wednesday, October 2, 2013 3:11 PM

10 | Before Working Inside Your Computer

Safety Instructions

Use the following safety guidelines to protect your computer from potential damage and

make sure your personal safety.

WARNING: Before working inside your computer, read the safety

information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

WARNING: Disconnect all power sources before opening the computer cover or

panels. After you finish working inside the computer, replace all covers, panels,

and screws before connecting to the power source.

CAUTION: Only a certified service technician is authorized to remove the

computer cover and access any of the components inside the computer.

CAUTION: To avoid damaging the computer, make sure that the work surface is

flat and clean.

CAUTION: To disconnect a network cable, first unplug the cable from your

computer and then unplug the cable from the network device.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab,

not on the cable itself. Some cables have connectors with locking tabs or

thumb-screws that you must disengage before disconnecting the cable.

When

disconnecting cables, keep them evenly aligned to avoid bending any

connector pins. When connecting cables, make sure that the connectors and

ports are correctly oriented and aligned.

CAUTION: Before touching anything inside your computer, ground yourself by

touching an unpainted metal surface, such as the metal at the back of the

computer. While you work, periodically touch an unpainted metal surface to

dissipate static electricity, which could harm internal components.

CAUTION: To avoid damaging the components and cards, handle them by their

edges and avoid touching pins and contacts.

book.book Page 10 Wednesday, October 2, 2013 3:11 PM

After Working Inside Your Computer | 11

After Working Inside Your Computer

CAUTION: Leaving stray or loose screws inside your computer may severely

damage your computer.

1 Replace all screws and make sure that no stray screws remain inside

your computer.

2 Connect any cables, peripherals, and any other part(s) you removed before

working

on your computer.

3 Connect your computer to the electrical outlet.

4 Turn on your computer.

book.book Page 11 Wednesday, October 2, 2013 3:11 PM

12 | Removing the Battery

Removing the Battery

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Close the display and turn the computer over.

2 Slide the battery latches outward to unlock the battery. You hear a click when the

battery is unlocked.

3 Lift and remove the battery off the computer base.

4 Turn the computer over and open the display as far as possible.

5 Press and hold the power button for 5 seconds, after the computer is unplugged,

ground the system board.

1 battery 2 battery latches (2)

book.book Page 12 Wednesday, October 2, 2013 3:11 PM

Replacing the Battery | 13

Replacing the Battery

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

Align the tabs on the battery with the slots on the battery bay and snap the battery

into

place.

book.book Page 13 Wednesday, October 2, 2013 3:11 PM

14 | Removing the Optical Drive

Removing the Optical Drive

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove the battery. See "Removing the Battery" on page 12.

Procedure

1 Remove the screw that secures the optical-drive assembly to the computer base.

2 Using your fingertips, slide the optical-drive assembly out of the optical-drive bay.

1 screw 2 optical-drive assembly

book.book Page 14 Wednesday, October 2, 2013 3:11 PM

Removing the Optical Drive | 15

3 Remove the screw that secures the optical-drive bracket to the

optical-drive assembly and remove the optical-drive bracket.

4 Carefully pull the optical-drive bezel and remove it from the optical drive.

1 optical-drive bezel 2 optical drive

3 screw 4 optical-drive bracket

book.book Page 15 Wednesday, October 2, 2013 3:11 PM

16 | Replacing the Optical Drive

Replacing the Optical Drive

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Align the tabs on the optical-drive bezel with the slots on the optical drive and snap

the optical-drive bezel into place.

2 Align the screw hole on the optical-drive bracket with the screw hole on

the optical-drive assembly and replace the screw that secures the optical-drive

bracket to the optical-drive assembly.

3 Slide the optical-drive assembly into the optical-drive bay and align the screw hole

on the optical-drive bracket with the screw hole on the computer base.

4 Replace the screw that secures the optical-drive assembly to the computer base.

Postrequisites

Replace the battery. See "Replacing the Battery" on page 13.

book.book Page 16 Wednesday, October 2, 2013 3:11 PM

Removing the Keyboard | 17

Removing the Keyboard

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove the battery. See "Removing the Battery" on page 12.

Procedure

1 Open the display as far as possible.

2 Using a plastic scribe, pry the keyboard from the tabs on the palm rest.

1 tabs (4) 2 plastic scribe

3 keyboard

book.book Page 17 Wednesday, October 2, 2013 3:11 PM

18 | Removing the Keyboard

3 Turn the keyboard over and place it on the palm rest.

4 Lift the connector latch and disconnect the keyboard cable from the

keyboard-cable connector.

5 Lift the keyboard off the palm rest.

1 keyboard cable 2 connector latch

3 keyboard 4 palm rest

1 2

book.book Page 18 Wednesday, October 2, 2013 3:11 PM

Replacing the Keyboard | 19

Replacing the Keyboard

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Slide the keyboard cable into the keyboard-cable connector and press down on the

connector latch to secure the cable.

2 Slide the tabs at the bottom of the keyboard into the slots on the palm-rest and

place the keyboard on the palm rest.

3 Gently press around the edges of the keyboard to secure the keyboard under the

tabs on the palm rest.

4 Replace the screws that secure the keyboard to the computer base.

Postrequisites

Replace the battery. See "Replacing the Battery" on page 13.

book.book Page 19 Wednesday, October 2, 2013 3:11 PM

20 | Removing the Base Cover

Removing the Base Cover

WARNING: Before working inside your computer, read the safety information that

shipped with your computer and follow the steps in "Before Working Inside Your

Computer" on page 9. After working inside your computer, follow the instructions

in "After Working Inside Your Computer" on page 11. For additional safety best

practices information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove the battery. See "Removing the Battery" on page 12.

Procedure

1 Loosen the captive screws that secure the base cover to the computer base.

2 Using your fingertips, lift the base cover out of the slots on the computer base.

1 captive screws (2) 2 base cover

book.book Page 20 Wednesday, October 2, 2013 3:11 PM

Leht laadib ...

Dell Inspiron 5735 Omaniku manuaal

Bränd: Dell

Mudel: Inspiron 5735

Kategooria: Märkmikud

Tüüp: Omaniku manuaal

See käsiraamat sobib ka

Inspiron M731R

Laadige alla PDF

aruanne

teistes keeltes

English: Dell Inspiron 5735 Owner's manual

Seotud paberid

Muud dokumendid

RV Designer H531 paigaldusjuhend