Scheppach 5901404904 Kasutusjuhend

Kaubamärk: Scheppach

Mudel: 5901404904

Tüüp: Kasutusjuhend

See juhend sobib ka

DECO-XL

Nachdrucke, auch auszugsweise, bedürfen der Genehmigung. Technische Änderungen vorbehalten. Abbildungen beispielhaft!

Art.Nr.

5901404904

AusgabeNr.

5901404850

Rev.Nr.

04/09/17

Scroll Saw

Translation from the original instruction manual

DECO-XL

Scroll Saw

7-16

2 / 20

3 / 20

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 8

Fig. 5

4 / 20

Fig. 6 Fig. 7

Fig. 9

Fig. 12

Fig. 11

5 / 20

Fig. 10

Fig. 13

Fig. 14

Fig. 15

6 / 20

Fig. 18

Fig. 16

Fig. 17

Table of contents: Page:

Introduction 9

Device description 9

Scope of delivery 9

Intended use 9

Safety information 10

Technical data 12

Installation 12

Operation 13

Maintenance 14

10.

Storage 14

11.

Electrical connection 14

12.

Disposal and recycling 15

13.

Troubleshooting 16

14.

Declaration of conformity 19

15.

Guarantee certicate 20

7 / 20

Explanation of the symbols on the equipment

8 / 20

Read the operating instructions to reduce the risk of injury

Wear a breathing mask. Dust which is injurious to health can be generated

when working on wood and other materials. Never use the device to work on

any materials containing asbestos!

Wear safety goggles. Sparks generated during working or splinters, chips and

dust emitted by the device can cause loss of sight.

The required minimum age must be met.

In addition to the safety notes contained in the present

operating instructions and the special regulations of

your country, the generally recognized technical rules

for the operation of wood working machines must be

observed.

2. Device description (Fig. 1)

1. Clamping screw: for removing the saw blade.

2. Blade guard: protects your hands from injury.

3. Work piece holder

4. Shavings blower: keeps the workpiece area free

from dust.

5. Speed switch

6. On/Off switch

7. Angle scale: you can read the angle position of

the table with this scale.

8. Lighting

9. Flexible shaft with drill chuck

10. Setting gauge for saw blades without pin

11. Foot switch

12. Switch to change between foot switch operation

and continuous operation

3. Scope of delivery

• When you unpack the device, check all parts for

possible transport damages. In case of complaints

the supplier is to be informed immediately.

• Complaints received at a later date will not be

acknow ledged.

• Check the delivery for completeness.

• Read the operating instructions to make yourself

familiar with the device prior to using it.

• Only use original scheppach parts for accessories

as well as for wearing and spare parts. Spare parts

are available from your specialized dealer.

• Specify our part numbers as well as the type and

year of construction of the device in your orders.

m ATTENTION

The device and packaging materials are not

toys! Children must not be allowed to play with

plastic bags, lm and small parts! There is a

risk of swallowing and suffocation!

4. Intended use

CE tested machines meet all valid EC machine

guidelines as well as all relevent guidelines for

each machine.

• The machine must only be used in technically

perfect con dition in accordance with its designated

use and the in structions set out in the operating

manual, and only by safety-conscious persons who

are fully aware of the risks involved in oerating the

machine. Any functional dis orders, especially those

affecting the safety of the machine, sholud terefore

be rectied immediately.

1. Introduction

made in China

Dear customer,

we wish you a pleasant and successful working expe-

rience with your new scheppach Scroll Saw.

Note:

According to the applicable product liability law the

manufacturer of this device is not liable for damages

which arise on or in connection with this device in

case of:

• improper handling

• non-compliance with the instructions for use

• repairs by third party, non authorized skilled

workers

• installation and replacement of non-original spare

parts

• improper use

• failures of the electrical system due to the non-

compliance with the electrical specications and

the VDE 0100, DIN 57113 / VDE 0113 regulations

Warning

To avoid electrical hazards, re hazards, or damage

to the tool, use proper circuit protection.

Your drill press is wired at the factory for 230 V opera-

tion. Connect to a 230 V/15 amp branch circuit and

use a 15 amp time delay fuse or circuit breaker. To

avoid shock or re, replace power cord immediately if

it is worn, cut or damaged in any way.

Recommendations:

Read the entire text of the operating instructions

prior to the assembly and operation of the device.

These operating instructions are intended to make it

easier for you to get familiar with your device and uti-

lize its intended possibilities of use.

The operating instructions contain important notes on

how to work safely, properly and economically with

your machine and how to avoid dangers, save repair

costs, reduce downtime, and increase the reliability

and working life of the machine.

In addition to the safety regulations contained herein,

you must in any case comply with the applicable reg-

ulations of your country with respect to the operation

of the machine.

Put the operating instructions in a clear plastic folder

to protect them from dirt and humidity, and store them

near the machine. The instructions must be read and

carefully observed by each operator prior to starting

the work. Only persons who have been trained in the

use of the machine and have been informed on the

related dangers and risks are allowed to use the ma-

chine.

9 / 20

7 Use the correct electric tool

– Do not use low-output electric tools for heavy work.

– Do not use the electric tool for purposes for

which it is not intended. For example, do not

use handheld circular saws for the cutting of

branches or logs.

– Do not use the electric tool to cut rewood.

8 Wear suitable clothing

– Do not wear wide clothing or jewellery, which

can become entangled in moving parts.

– When working outdoors, anti-slip footwear is

recommended.

– Tie long hair back in a hair net.

9 Use protective equipment

– Wear protective goggles.

– Wear a mask when carrying out dust-creating

work.

10 Connect the dust extraction device

– If connections for dust extraction and a col-

lecting device are present, make sure that

they are connected and used properly.

– Operation in enclosed areas is only permitted

with a suitable extraction system.

11 Do not use the cable for purposes for which it is

not intended

– Do not use the cable to pull the plug out of

the outlet. Protect the cable from heat, oil and

sharp edges.

12 Secure the workpiece

– Use the clamping devices or a vice to hold the

workpiece in place. In this manner, it is held

more securely than with your hand.

– An additional support is necessary for long

workpieces (table, trestle, etc.) in order to

prevent the machine from tipping over.

– Always press the workpiece rmly against

the working plate and stop in order to prevent

bouncing and twisting of the workpiece.

13 Avoid abnormal posture

– Make sure that you have secure footing and

always maintain your balance.

– Avoid awkward hand positions in which a

sudden slip could cause one or both hands to

come into contact with the saw blade.

14 Take care of your tools

– Keep cutting tools sharp and clean in order to

be able to work better and more safely.

– Follow the instructions for lubrication and for

tool replacement.

– Check the connection cable of the electric tool

regularly and have it replaced by a recognised

specialist when damaged.

– Check extension cables regularly and replace

them when damaged.

– Keep the handle dry, clean and free of oil and

grease.

15 Pull the plug out of the outlet

– Never remove loose splinters, chips or

jammed wood pieces from the running saw

blade.

• The safety, work and maintenance instructions

of the manufacturer as well as the technical data

given in the calibrations and dimensions must be

adhered to.

• Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must

also be adhered to.

• The machine may only be used, maintained, and

operated by persons familiar with it and instructed

in its operation and procedures. Arbitrary alterations

to the machine release the manufacturer from all

responsibility for any resulting damages.

• The machine may only be used with original

accessories and tools made by the manufacturer.

• Any other use exceeds authorization. The

manufacturer is not responsible for any damages

resulting from un authorized use; risk is the sole

responsibility of the operator.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

equipment is used in commercial, trade or industrial

businesses or for equivalent purposes.

5. Safety information

Attention! The following basic safety measures

must be observed when using electric tools for

protection against electric shock, and the risk of

injury and re. Read all these notices before using

the electric tool and keep the safety instructions for

later reference.

Safe work

1 Keep the work area orderly

– Disorder in the work area can lead to acci-

dents.

2 Take environmental inuences into account

– Do not expose electric tools to rain.

– Do not use electric tools in a damp or wet

environment.

– Make sure that the work area is well-illuminat-

ed.

– Do not use electric tools where there is a risk

of re or explosion.

3 Protect yourself from electric shock

– Avoid physical contact with earthed parts (e.g.

pipes, radiators, electric ranges, cooling units).

4 Keep children away

– Do not allow other persons to touch the equip-

ment or cable, keep them away from your work

area.

5 Securely store unused electric tools

– Unused electric tools should be stored in a dry,

elevated or closed location out of the reach of

children.

6 Do not overload your electric tool

– They work better and more safely in the speci-

ed output range.

10 / 20

• Always use the blade guard to avoid possible injury

due to blade breakage.

• Never leave the scroll saw work area with the

power 01), or before the machine has come to a

complete stop.

• Do not perform layout, assembly or set up work

on the table while the cutting tool is in operation.

• Never turn your scroll saw on before clearing

the table of all objects: (tools, scraps of wood,

etc) except for the workpiece and related feed or

support devices for the operation planned.

Remaining hazards

The machine has been built using modern tech-

nology in accor dance with recognized safety

rules. Some remaining hazards, how ever, may

still exist.

• Long hair and loose clothing can be hazardous

when the work piece is rotating. Wear personal

protective gear such as a hair net and tight tting

work clothes.

• Saw dust and wood chips can be hazardous. Wear

per so nal protective gear such as safety goggles

and a dust mask.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Even when all safety measures are taken, some

remaining hazards which are not yet evident may

still be present.

• Remaining hazards can be minimized by following

the instructions in „Safety Precautions“, „Proper

Use“ and in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of

the blade and a decrease in performance in terms

of nish and cutting precision.

• Avoid accidental starts: do not press the start

button while inserting the plug into the socket.

Keep this safety information in a safe place.

– During non-use of the electric tool or prior to

maintenance and when replacing tools such

as saw blades, bits, milling heads.

16 Do not leave a tool key inserted

– Before switching on, make sure that keys and

adjusting tools are removed.

17 Avoid inadvertent starting

– Make sure that the switch is switched off

when plugging the plug into an outlet.

18 Use extension cables for outdoors

– Only use approved and appropriately identi-

ed extension cables for use outdoors.

– Only use cable reels in the unrolled state.

19 Remain attentive

– Pay attention to what you are doing. Remain

sensible when working. Do not use the elec-

tric tool when you are distracted.

20 Check the electric tool for potential damage

– Protective devices and other parts must be

carefully inspected to ensure that they are

fault-free and function as intended prior to

continued use of the electric tool.

– Check whether the moving parts function

faultlessly and do not jam or whether parts

are damaged. All parts must be correctly

mounted and all conditions must be fullled to

ensure fault-free operation of the electric tool.

– The moving protective hood may not be xed

in the open position.

– Damaged protective devices and parts must

be properly repaired or replaced by a recog-

nised workshop, insofar as nothing different is

specied in the operating manual.

– Damaged switches must be replaced at a

customer service workshop.

– Do not use any faulty or damaged connection

cables.

– Do not use any electric tool on which the

switch cannot be switched on and off.

21 ATTENTION!

– Exercise elevated caution for double mitre

cuts.

22 ATTENTION!

– The use of other insertion tools and other ac-

cessories can entail a risk of injury.

23 Have your electric tool repaired by a qualied

electrician

– This electric tool conforms to the applicable

safety regulations. Repairs may only be per-

formed by an electrician using original spare

parts. Otherwise accidents can occur.

ADDITIONAL SAFETY RULES FOR SCROLL

SAWS

• This scroll saw is intended for use in dry conditions,

and for indoor use only.

• Do not cut pieces of material too small to hold by

hand outside the blade guard.

• Avoid awkward hand positions where a sudden slip

could cause a hand to move into the blade.

11 / 20

• Release the lock screw (D) and bring the indicator

to the zero position. Fasten the screw. Please note:

the angle scale is a useful piece of supplementary

equip ment, but should not be used for precision

work. Use scrap wood for saw tests, adjust the

bench if neces sary.

Note: The bench should not be on the motor

block, this can cause undesireable noise.

Horizontal saw bench and diagonal cuts, Fig. 2+3

• The saw bench can be positioned into a 450

diagonal position or be left in the horizontal

position.

• You can read off the approximate slope angle

by using the angle scale located under the work

bench. For more exact adjustment, use scrap wood

for some saw tests; adjust the bench if necessary.

Blade guard assembly, Fig. 4

Install the blade guard to the holder as shown in the

diagram. Secure the screws with a nut and washer.

• Lift the saw onto the frame and base and push it

onto the workbench.

• Familiarize yourself with the saw operating

elements and features.

Mounting the saw on a work bench, Fig. 5

• A workbench made from solid wood is betier than

one made of plywood, as interfering vibrations and

noise are more noticeable with plywood.

• The necessary tools and small parts for assembling

the saw on a workbench are not supplied with

the saw. However, use equipment of at least the

following size:

E Saw body

F Foam rubber base

GWork bench

H Flat seal

I Washer

J Hexagonal nut

K Lock nut

L Hexagonal bolt

Ouantity Description

4 Hexagonal bolts (6mm) 1/4-20 x length

4 Flat seal (7mm) 9/321.0

4 Washers (7mm) 9/321.0.

8 Hexagonal nuts (6 mm) 1/4-20

First of all, drill holes into the seating surface and

then insert the screws.

• A foam rubber base for reduction of noise is

not supplied with the saw either. However, we

expressly recommend that you use such a base to

keep vibration and noise to a minimum. Ideal size

400 x 240 mm.

CHANGING THE SAW BLADES

Warning: Switch off the saw and remove the

mains supply plug before installing saw b!ades

in order to avoid injuries caused by unintentiona!

activation of the saw.

6. Technical data

Extent of delivery

Scroll saw

Flexible Wave

Accessories kit

Operating instructions

Technical data

Dimensions

L x W x H mm

630 x 320 x 380

Bench size mm

ø 255 x 415

Saw blade

length mm

127

Cutting height

max. mm

Working depth mm

405

Lifting

movement mm

Lifting speed 1/min

(electronical)

550 – 1600

Bench diagonal

adjustment left

degrees

0 – 45

Weight kg

11,8

Suction connection

piece ø mm

Motor

Electrical motor

230-240 V~/50 Hz

Power W

70 (S1); 90 (S2 30min);

125 (S2 5min)

* Duty type S2 – Short-time duty.

Operation at constant load for 30minutes or less, fol-

lowed by a time de-energized and at rest of sufcient

duration to re-establish machine temperatures within 2

K of the ambient temperature.

Noise and vibration

Total vibration values determined in accordance with

EN 61029.

load no load

sound pressure level L

dB(A) 77,3 67, 2

uncertainty K

dB 3 3

sound power level L

dB(A) 87,4 78,4

uncertainty K

dB 3 3

Wear hearing protection.

The effects of noise can cause a loss of hearing. Total

vibration values (vector sum - three directions) deter-

mined in accordance with EN 61029.

7. Installation

Setting the saw bench, Fig. 2

Setting the angle scale

• Release the star button (A and bring the saw bench

(B) to a right angle (C) in relation to the saw blade.

• Use a 90° angle tc measure the right angle between

the blade and the bench. The saw blade be 90° to

the angle.

• Close the star button again when the distance

between the blade and the 90° angle is at a minimum.

The bench should then be at 90° to the saw blade.

12 / 20

• The saw is best suited tor sheets of wood less than

2.5 cm thick.

• Feed the wood especially slowly against the blade

and avoid abrupt curves to prevent the saw blade

from breaking, if you wish to cut wood sheets

thickerthan 2.5 cm.

• Saw blade teeth blunten over time, saw blades

must be replaced. The saw blades are sufcient

tor 1/2 to 2 operating time depending upon the type

of wood.

• Try and make sure that the saw blade follows the

grain of the wood in order to obtain a clean cut.

• The saw speed must be reduced to minimum when

cutting precious and non-terrous metals.

INSIDE CUTS

Warning: Switch off the saw and remove the

mains supply plug before installing saw blades

in order to avoid injuries caused by unintentional

activation of the saw.

This saw is suited also to inside cuts cuts not starting

at the edge of the work piece. Proceed as follows:

• Drill a 6 mm hole in the work piece.

• Loosen the blade tension er and release the

tension in the blade.

• Place the bore hole over the saw blade slot in the

work bench.

• Install the saw blade through the hole in the work

piece and through the work blade slot, and fasten

the blade to the holders.

• When you have completed the inside cut, remove

the saw blade and then remove the workpiece from

the bench.

Flexible shaft, Fig. 12-14

• Remove protective cap (O) from the threaded

bushing (Fig. 13).

• Place exible shaft onto the threaded bushing (Fig. 14).

• Clamp tool in the drill chuck (D 3.2).

• Firmly hold threaded shaft at the handle and switch

on the speed control.

• Having nished the work, remove the exible

shaft and place the protective cap in place.

Attention: When working with the exible shaft,

cover the saw blade with the blade guard.

Foot switch / continuous operation (Fig. 1+15+16)

The machine can be operated in continuous operati-

on or with the additional foot switch (11). The switch

(12) is used to select between the operating modes.

The operating mode should always be selected when

the machine is switched off.

The machine is in the foot switch mode when the

switch is at the „0“ position.

The machine is in the continuous mode when the

switch is at the “I“ position.

Attention! The machine may start due to unintenti-

onal actuation of the foot switch in the foot switch

mode.

Attention! Never leave the machine unattended while

it is switched on.

A. Flat saw-blades Fig. 6

Use the adapter with at saw-blades.

The saw-blade is xed with Allen screws.

A 1 Saw-blade removal, g. 7+8, 10

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Slightly press the upper arm (M) down (g. 10).

• Then remove the sawblade by pulling it forward out

of the supports and through the access perforation

in the table.

A 2 Inserting the saw-blade:

• Put the saw-blade with the two adapters into the

lower support, the other end into the upper support.

• Slightly press the upper arm (M) down (g 10)

before hooking it in.

• Tighten the blade with the tightening screw (1)

(g.7) by rotating it clockwise. Check the tightness

of the blade. Keep on rotating clockwise in order to

tighten the blade even more.

B. Saw-blade with pins

B 1 Saw blade removal, g. 7 + 8

• Extract the saw-blade by rst unscrewing the

tightening screw (1).

• Remove the saw-blade from the upper and lower

support by slightly pressing the saw´s upper arm

down (g. 10, M).

B 2 Inserting the saw-blade g 7, 9-11

• Lead one end of the saw-blade through the

perforation in the table and insert the saw-blade

pins into the notch. Repeat this procedure at the

upper blade support.

• Before hooking it in, slightly press the saw´s upper

arm down. (Fig 9; Nr. 10)

• Check the position of the blade pins at the supports

(g 11).

• Tighten the blade by means of the tightening screw.

Check the blade´s tightness. Keep on rotating

clockwise in order to tighten the blade even more.

(Fig. 7).

8. Operation

A scroll saw is fundamentally a „curve cutting tool“

but which can also carry out straight and angled edge

cuts. Familiarise yourself with the following important

points prior to commissioning the saw.

• The saw does not automatically cut wood. You must

feed the wood against the saw blade manually.

• The cutting process occurs on I y while the blade

is moving downwards.

• Feed the wood slowly against the saw blade as

the saw blade teeth are small and cut only while

moving downwards.

• AlI persons carrying out work with the saw require

training. The saw blade may break easily during this

training time Iwhile the operator is sti1l unfamiliar

with the saw.

13 / 20

Saw arm bearings

Lubricate the saw arm bearings every 50 hours. Pro-

ceed as follows (Fig. 18).

• Turn the saw to the side

• Apply a generous amount of SAE 20 oil to the shaft

end and bronze bearings.

• Let the lubricant oil work in overnight.

• Repeat the procedure the next day on the other

side of the saw.

There are no parts inside the equipment which requi-

re additional maintenance.

Special accessories

Pin saw blade-universal

135 x 2,0 x 0,25 Z 10

blade mm 1 set = 6 pieces, Article No. 8800 0011

Pin saw blade- wood/plastic mm

135 x 2,0 x 0,25 Z 7

1 set = 6 pieces, Article No. 8800 0012

Pin saw blade-wood mm

135 x 3,0 x 0,5 Z 4

1 set = 6 pieces, Article No. 8800 0013

10. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C. Store the electrical tool in its original packaging.

11. Electrical connection

The installed electric motor is completely wired ready

for operation.

The customer’s connection to the power supply sys-

tem, and any extension cables that may be used,

must conform with local regulations.

IMPORTANT REMARK:

The motor is automatically switched off in the event

of an overload. The motor can be switched on again

after a cooling down period that can vary.

DEFECTIVE ELECTRICAL CONNECTION CABLES

Electrical connection cables often suffer insulation

damage.

Possible causes are:

• Pinch points when connection cables are run

through window or door gaps.

• Kinks resulting from incorrect attachment or laying

of the connection cable.

• Cuts resulting from running over the connecting

cable.

• Insulation damage resulting from forcefully pulling

out of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not

be used as the insulation damage makes them ex-

tremely hazardous.

Switching on/off (Fig. 1+15)

It is possible to switch the saw on by pressing the

green „I“ button (6).

In order to switch the saw off again, it is necessary to

press the red „0“ button (6).

The red warning light (a) indicates whether the ma-

chine is switched on or off. The machine is switched

on when this lights up. (The machine only starts up in

the foot switch mode once the pedal is actuated, the

red warning light illuminates anyway.)

You can only switch between foot switch and con-

tinuous operation when the red warning light is not

illuminated. If necessary, switch machine off rst by

pressing the red button “0” (6).

Make sure you are aware of what operating mode

(pedal/continuous operation) your machine is in befo-

re switching it on.

Beware of unintentional actuation of the foot switch.

Set the pedal (11) on the ground. The machine can

be switched on/off in pedal mode when the pedal is

actuated. A foot switch for switching on/off is practi-

cal, especially for internal cuttings, since your hands

are kept free and you can fully concentrate on the

work piece under the scroll saw. However, it cannot

inuence the speed.

With the continuously variable electronic speed con-

trol (5), the cutting speed can be increased by turning

to the right or reduced by turning to the left.

Lighting system (8) (Fig.1+17)

The lighting system can be switched on by pressing

the switch (b) on the lamp.

The lighting system is switched off if the switch is

pressed again.

To change the batteries (2x AAA R03 1.5), open

the battery compartment on the bottom of the light

by removing the three screws (c) using a Phillips

screwdriver.

Insert the new batteries. Dispose of the old batteries

properly.

Fit the cover of the battery compartment in reverse

order.

9. Maintenance

Warning: In the interests of operational safety,

always switch off the saw and remove the mains

plug before carrying out maintenance work.

General

Wipe chips and dust off the machine from time to time us-

ing a cloth.

Re-application of the wax coating on the workbench

makes feeding the workpiece to the blade easier.

Motor

The mains cable should be replaced immediately if

pulled out, cut or damaged in any other way.

Do not lubricate the motor bearings or internal parts!

14 / 20

15 / 20

Check electrical connection cables regularly for dam-

age. Make sure the cable is disconnected from the

mains when checking.

Electrical connection cables must comply with the

regulations applicable in your country.

SINGLE-PHASE MOTOR

• The mains voltage must coincide with the voltage

specied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have

a cross-section of 1.5 mm2, and beyond 25 m at

least 2.5 mm2.

• The connection to the mains must be protected with

a 16 A slow-acting fuse.

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

If a motor has to be returned, it must always be dis-

patched with the complete driving unit and switch.

12. Disposal and recycling

The equipment is supplied in packaging to prevent

it from being damaged in transit. The raw materials

in this packaging can be reused or recycled. Never

place batteries in your household refuse, in re or

in water. Batteries should be collected, recycled or

disposed of by environment-friendly means. The

equipment and its accessories are made of various

types of material, such as metal and plastic. Defec-

tive components must be disposed of as special

waste. Ask your dealer or your local council.

15 / 20

16 / 20

13. Troubleshooting

Warning: In the interests of operational safety, always switch off the saw and remove the mains plug before

carrying out maintenance work.

Fault Possible causes Action

Saw blades break Tension incorrectly set Set the correct tension

Load to great Feed the workpiece more slowly

Incorrect saw blade variety Use the correct saw blades

Workpiece not fed straight Avoid exerting pressure from the side

Motor does not function Mains Gable faulty Change faulty parts

Motor faulty Call customer service. Do not attempt to

repair the motor yourself as this should be

carried out by trained personnel.

Vibration

NOTE: The saw vibrates slightly

when the motor is running in normal

operation.

Saw incorrectely installed Refer to the instructions given earlier in this

manual for information on installing the saw

Unsuitable underlay The heavier the work bench is,the less the

vibration. A bench made from ply wood

always vibrates more than one made from

solid wood. Select the work bench best

suited to your working conditions

The work bench is not screwed down

or is on the motor

Tighten the locking lever

The motor is not secured Securely screw the motor in place

Saw blade swings out

Holders not aligned straight

Holders not aligned Losen the screws with which the holders are

fastenedto the arm. Align the holders so that

they are perpendicular to each other and

retighten the screws.

17 / 20

brown

blue

PCB

Potentiometer

Foot Switch

Transfer Switch

Power Light

on-off Switch

Plug and Power Line

Ground Wire

Blue

Brown

erklärt folgende Konformität gemäß

EU-Richtlinie und Normen für den Artikel

hereby declares the following conformity under the

EU Directive and standards for the following article

déclare la conformité suivante selon la directive UE

et les normes pour l’article

dichiara la seguente conformità secondo le diret-

tive e le normative UE per l‘articolo

prohlašuje následující shodu podle smernice EU a

norem pro výrobek

az EU-irányelv és a vonatkozó szabványok szerinti

következo megfeleloségi nyilatkozatot teszi a

termékre

ovime izjavljuje da postoji sukladnost prema EU-

smjernica i normama za sljedece artikle

declară următoarea conformitate corespunzător

directivelor şi normelor UE pentru articolul

Normları geregince asagıdaki uygunluk açıkla

masını sunar.

FIN

vakuuttaa täten, että seuraava tuote täyttää ala

esitetyt EU-direktiivit ja standardit

deklaruje, ze produkt jest zgodny z nastepujacymi

dyrektywami UE i normami

SLO

izjavlja sledeco skladnost z EU-direktivo in nor-

mami za artikel

prehlasuje nasledujúcu zhodu podla smernice EU a

noriem pre výrobok

EST

kinnitab järgmist vastavus vastavalt ELi direktiivi ja

standardite järgmist artiklinumbrit

pareiškia, taip atitiktis pagal ES direktyvos ir

standartai šį straipsnį

apliecina šādu saskaņā ar ES direktīvu atbilstības

un standarti šādu rakstu

verklaart hierbij dat het volgende artikel voldoet

aan de daarop betrekking hebbende EG-richtlijnen

en normen

RUS

заявляет о соответствии товара следующим

директивам и нормам ЕС

declara o seguinte conformidade com a Directiva

da UE e as normas para o seguinte artigo

declara la conformidad siguiente según la directiva

la UE y las normas para el artículo

erklærer hermed, at følgende produkt er ioverens-

stemmelse med nedenstående EUdirektiver og

standarder:

försäkrar härmed följande överensstämmelse en-

ligt EU-direktiv och standarder för följande artikeln

erklærer herved følgende samsvar under EU-

direktiv og standarder for følgende artikkel

İlgili ürün aşağıdaki Avrupa birliği direkti

standartlarına uygundur.

Scroll saw: DECO-XL

Standard references: EN 61029-1; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Declaration of conformity

Ichenhausen, den 04.09.2017 _____________________

Unterschrift / Markus Bindhammer / Technical Director

First CE: 2014

Art.-No. 5901404904

Subject to change without notice

Documents registar: Christian Wilhelm

Günzburger Str. 69, D-89335 Ichenhausen

2009/105/EC

2014/35/EU

2006/28/EC

2005/32/EC

X 2014/30/EU

2004/22/EC

1999/5/EC

97/23/EC

90/396/EC

X 2011/65/EU

89/686/EC_96/58/EC

X 2006/42/EC

Annex IV

Notied Body:

Notied Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured L

= xx dB(A); guaranteed L

= xx dB(A)

P = KW; L/Ø = cm

Notied Body:

Notied Body No.:

2004/26/EC

Emission. No:

■

Garantie D

Offensichtliche Mängel sind innerhalb von 8 Tagen nach Erhalt der Ware anzuzeigen, andernfalls verliert der Käufer sämtliche Ansprüche

wegen solcher Mängel. Wir leisten Garantie für unsere Maschinen bei richtiger Behandlung auf die Dauer der gesetzlichen Gewähr-

leistungsfrist ab Übergabe in der Weise, dass wir jedes Maschinenteil, dass innerhalb dieser Zeit nachweisbar in Folge Material- oder

Fertigungsfehler unbrauchbar werden sollte, kostenlos ersetzen. Für Teile, die wir nicht selbst herstellen, leisten wir nur insoweit Gewähr,

als uns Gewährleistungsansprüche gegen die Vorlieferanten zustehen. Die Kosten für das Einsetzen der neuen Teile trägt der Käufer.

Wandlungs- und Minderungsansprüche und sonstige Schadensersatzansprüche sind ausgeschlossen.

Warranty GB

Apparent defects must be notied within 8 days from the receipt of the goods. Otherwise, the buyerís rights of claim due to such defects

are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in

such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrica-

tion within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims

against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the

reduction of purchase price as well as any other claims for damages shall be excluded.

Garantie FR

Des défauts visibles doivent être signalés au plus tard 8 jours après la réception de la marchandise, sans quoi líacheteur perd tout droit à

des redevances pour de tels défauts. Nous garantissons nos machines, dans la mesure où elles sont maniées correctement, pour la durée

légale de garantie à compter de la remise dans ce sens que nous remplaçons gratuitement toute pièce de la machine devenue inutilisable

durant cette période pour des raisons díerreur de matériau ou de fabrication. Toutes pièces que nous ne fabriquons pas nous-mêmes ne

sont garanties que si nous possédons des droits à la garantie vis-à-vis des fournisseurs respectifs. Les frais pour la mise en place des

nouvelles pièces sont à la charge de líacheteur. Tous droits à rédhibition et toutes prétentions à diminutions ainsi que tous autres droits à

líindemnité sont exclus.

Garanzia I

Vizi evidenti vanno segnalati entro 8 giorni dalla ricezione della merce, altrimenti decadono tutti i diritti dellíacquirente inerenti a vizi del

genere. Appurato un impiego corretto da parte dellíacquirente, garantiamo per le nostre macchine per tutto il periodo legale di garanzia a

decorrere dalla consegna in maniera tale che sostituiamo gratuitamente qualsiasi componente che entro tale periodo presenti dei vizi di

materiale o di fabbricazione tali da renderlo inutilizzabile. Per componenti non fabbricati da noi garantiamo solo nella misura nella quale

noi stessi possiamo rivendicare diritti a garanzia nei confronti dei nostri fornitori. Le spese per il montaggio dei componenti nuovi sono a

carico dellíacquirente. Sono escluse pretese di risoluzione per vizi, di riduzione o ulteriori pretese di risarcimento danni.

Garantía ES

Los defectos evidentes deberán ser noticados dentro de 8 días después de haber recibido la mercancía, de lo contrario el comprador

pierde todos los derechos sobre tales defectos. Garantizamos nuestras máquinas en caso de manipulación correcta durante el plazo de

garantía legal a partir de la entrega. Sustituiremos gratuitamente toda pieza de la máquina que dentro de este plazo se torne inútil a causa

de fallas de material o de fabricación. Las piezas que no son fabricadas por nosotros mismos serán garantizadas hasta el punto que

nos corresponda garantía del suministrador anterior. Los costes por la colocación de piezas nuevas recaen sobre el comprador. Están

excluidos derechos por modicaciones, aminoraciones y otros derechos de indemnización por daños y perjuicios.

Garantia PT

Para este aparelho concedemos garantia de 24 meses. A garantia cobre exclusivamente defeitos de matérial ou de fabricação. Peças

avariadas são substituidas gratuitamente. cabe ao cliente efetuar a substituição. Assumimos a garantia unicamente de peças genuinas

scheppach.

Não há direito à garantia no caso de: peças de desgaste, danos de transporte, danos causados pelo manejo indevido ou pela desatenção

as instruções de serviço, falhas da instalação elétrica por inobservançia das normas relativas á electricidade. Além disso, a garantia só

poderá ser reinvidicada para aparelhos que não tenham sido consertados por lerceiros. O cartão de garantia só vale em conexão com

a fatura.

Garantie NL

Zichtbare gebreken moeten binnen de 8 dagen na ontvangst van de goederen worden gemeld, zo niet verliest de verkoper elke aanspraak

op grond van deze gebreken. Onze machines worden geleverd met een garantie voor de duur van de wettelijke garantietermijn. Deze

termijn gaat in vanaf het moment dat de koper de machine ontvangt. De garantie houdt in dat wij elk onderdeel van de machine dat binnen

de garantietermijn aantoonbaar onbruikbaar wordt als gevolg van materiaal- of productiefouten, kosteloos vervangen. De garantie vervalt

echter bij verkeerd gebruik of verkeerde behandeling van de machine. Voor onderdelen die wij niet zelf produceren, geven wij enkel de

garantie die wij zelf krijgen van de oorspronkelijke leverancier. De kosten voor de montage van nieuwe onderdelen vallen ten laste van de

koper. Eisen tot het aanbrengen van veranderingen of het toestaan van een korting en overige schadeloosstellingsclaims zijn uitgesloten.

Garanti NO

Åpenbare mangler skal meldes innen 8 dager etter at varen er mottatt, ellers taper kunden samtlige krav pga slik mangel. Vi gir garanti for

at våre maskiner ved riktig behandling under den rettslige garantitidens varighet, fra overlevering, på den måten at vi erstatter kostnadsfritt

hver maskindel, som innen denne tiden påviselig er ubrukbar som følge av material- eller produksjonsfeil. For deler som vi ikke produserer

selv, yter vi garanti kun i den utstrekning som garantikrav mot underleverandør tilkommer oss. Kjøperen bærer kostnadene ved montering

av nye deler. Endrings- og verditapskrav og øvrige skadeerstatningskrav er utelukkede.

Garanti SE

Uppenbara brister ska anmälas inom 8 dagar efter mottagandet, i annat fall förlorar köparen samtliga anspråk på grund av dessa brister.

Vi lämnar garanti för våra maskiner vid riktig hantering för den lagenliga garantitiden från övertagandet på det sättet, att vi kostnadsfritt

ersätter varje maskindel, som inom denna tid blir obrukbar bevisligen som följd av material eller tillverkningsfel. För delar, som vi inte

själva tillverkar, lämnar vi endast garanti i så måtto, som vi själva får garanti av våra underleverantörer. Kostnaderna för monteringen av de

nya delarna bär köparen. Förändrings och värdeminskningsanspråk och övriga skadeståndsanspråk är uteslutna.

Garanti DK

Med denna maskin följer en 24 månaders garanti. Garantin täcker endast material- och konstruktionsfel. Defekta delar ersätts utan

omkostningar, men kunden står för installationen. Vår garanti täcker endast orginal scheppach-delar. Anspråk på garanti öreligger inte för:

garantin täcker ej, transportskador, skador orsakade av felaktig behandling och då skötselföreskrifter inte beaktats. Vidare kan garantikrav

endast ställas för maskiner som inte har reparerats av tredje part.

Takuu FIN

Ilmeisistä puutteista tulee ilmoittaa kahdeksan päivän kuluessa tavaran vastaanottamisesta. Muutoin ostaja ei voi vaatia korvausta ko.

puutteista. Annamme takuun oikein käsitellyille koneillemme lakisääteiseksi takuuajaksi tavaran luovutuksesta alkaen siten, että vaihdam-

me korvauksetta minkä tahansa koneenosan, joka osoittautuu tämän ajan kuluessa käyttökelvottomaksi raaka-aine- tai valmistusvirhees-

tä johtuen. Osille, joita emme valmista itse, annamme takuun vain mikäli osien toimittaja on antanut niistä takuun meille. Uusien osien

asennuskustannukset maksaa ostaja. Purku- ja vähennysvaatimukset ja muut vahingonkorvausvaatimukset eivät tule kysymykseen.

Záruka SK

Zrejmé vady musia byť predstavené v priebehu 8 dni po obdržaní tovaru, ináč zákazník stratí všetky nároky týkajúce sa takejto vady.

Ponúkame záruku na naše aparáty, ktoré sú správne používané počas zákonného termínu záruky tak, že bezplatne vymeníme každú časť

aparátu, ktorá sa v priebehu tohto času môže stať dokázateľne nefunkčnou dôsledkom materiálnej či výrobnej vady. Na časti ktoré sami

nevyrábame, poskytujeme záruku iba v rozsahu, v ktorom nám prísluší nárok na záručné plněnie k subdodávateľovi. Za trovy týkajúce sa

inštalácie novej súčiastky je zodpovedný zákazník. Nárok na výmenu tovara, na zľavu a iné nároky na nahradenie škody sú vylúčené.

Garancija SLO

Očitne pomanjkljivosti je potrebno naznaniti 8 dni po prejemu blaga, v nasprotnem primeru izgubi kupec vse pravice do garancije zaradi

takšnih pomanjkljivosti. Za naše naprave dajemo garancijo ob pravilni uporabi za čas zakonsko določenega roka garancije od predaje in

sicer na takšen način, da vsak del naprave brezplačno nadomestimo, za katerega bi se v tem roku izkazalo, da je zaradi slabega materiala

ali slabe izdelave neuporaben. Za dele, ki jih sami ne izdelujemo, jamčimo samo toliko, kolikor zahteva garancija drugih podjetij. Stroški za

vstavljanje novih delov nosi kupec. Zahteve za spreminjanje in zmanjšanje ter ostale zahteve za nadomestilo škode so izključene.

Záruka CZ

Viditelné vady jsou poukazatelné během 8 dní od obdržení zboží, jinak ztrácí zákazník všechny nároky týkající se takovýchto vad.

Poskytujeme záruku na naše stroje, s kterými je správně zacházeno, na dobu zákonnné záruční lhůty začínající od doručení tak, že bezplatně

vyměníme každou část stroje, která se během této doby může stát prokazatelně nepoužitelnou následkem materiálové či výrobní vady. Na díly,

které sami neopravujeme, poskytujeme záruku pouze v rozsahu , v němž nám přísluší nárok na záruční plnění vůči subdodavateli . Náklady na

instalaci nového dílu nese zákazník. Nárok na výměnu zboží, na slevu a jiné nároky na odškodnění jsou vyloučené.

Garantii EST

Ilmselgetest vigadest tuleb teatada 8 päeva jooksul pärast kauba kättesaamist, vastasel juhul kaotab ostja kõik õigused garantiile nimetatud

vigade tõttu. Õige käsitsemise korral anname oma masinatele garantii seadusega ettenähtud ajaks alates kauba üleandmisest nii, et vahetame

tasuta välja kõik masina osad, mis nimetatud aja jooksul peaks muutuma kasutuskõlbmatuks materjali- või tootmisvea tõttu. Osade eest, mida

me ise ei tooda, anname garantii vaid selles osas, mis tarnija on meile garanteerinud. Uute osade paigaldamise kulud kannab ostja. Muutmis-

ja amortisatsiooninõuded ning muud kahjutasunõuded välistatakse.

Гарантия (RUS)

Об очевидных дефектах необходимо уведомить в течение 8 дней после получения товара. В ином случае все претензии покупателя

по таким дефектам не принимаются. Мы предоставляем гарантию на наши машины при условии правильного обращения с ними.

Гарантия действует с момента передачи машины в течение установленного законом гарантийного срока. В течение этого времени мы

гарантируем бесплатную замену любой части машины, если они стали непригодны к использованию в результате доказуемых ошибок

в применяемых материалах или при изготовлении. На части машины, которые мы не изготавливаем сами, мы предоставляем гаран-

тии в той мере, насколько нас касаются рекламационные претензии к изготовителям. Расходы по замене деталей несет покупатель.

Претензии на расторжение договора купли-продажи, штрафы и прочие требования о возмещении ущерба исключаются.

Gwarancja (POL)

Wszelkie uszkodzenia muszą być zgłaszane w przeciągu 8 dni od daty otrzymania towaru, w przeciwnym wypadku, prawo do reklamacji

wygasa. Gwarantujemy, że w czasie trwania gwarancji wymienimy wszelkie części maszyny, które okażą się niesprawne na skutek wad

materiału z jakiego zostały wykonane lub błędów w produkcji bez dodatkowych opłat pod warunkiem, że maszyna będzie obsługiwana zgodnie

z zaleceniami. W odniesieniu do części nie produkowanych przez nas, gwarancja obowiązuje tylko w przypadku naszych dostawców. Koszty

instalacji nowych części są ponoszone przez klienta. Odszkodowania wynikłe z uszkodzeń maszyny oraz redukcje ceny zakupu maszyny w

ramach reklamacji nie będą rozpatrywane.

Garantija (LAT)

Acīmredzami defekti ir jāpaziņo 8 dienu laikā no preces saņemšanas. Pretējā gadījumā pircēja tiesības pieprasīt atlīdzību par šādiem

defektiem ir spēkā neesošas. Mēs dodam garantiju savām iekārtām, ja pircējs pret tām atbilstoši izturas garantijas laikā. Mēs apņemamies

bez maksas piegādāt jebkuru rezerves daļu, kas iespējams kļuvusi nelietojama bojātu materiālu vai ražošanas defektu dēļ šajā laika periodā.

Attiecībā uz rezerves daļām, kuras nav mūsu ražotas, mēs garantējam tikai gadījumā, ja mums ir garantija no saviem piegādātājiem. Jauno

detaļu uzstādīšanas izmaksas ir jāuzņemas pircējam. Pirkuma atcelšana vai pirkuma cenas samazināšana, kā arī jebkuras citas prasības par

bojājumu atlīdzināšanu netiek izskatītas.

Garantija (LIT)

Dėl akivaizdžiai matomų defektų turi būti informuota per 8 dienas nuo įrenginio gavimo momento. Kitu atveju pirkėjo teisė reikšti pretenziją

dėl šių defektų yra negaliojanti. Savo įrenginiams mes garantuojame įstatymo nustatytą pilną aptarnavimą garantinio laikotarpio metu, jei yra

laikomasi gamintojo-vartotojo susitarimo ir mes pažadame nemokamai pakeisti bet kurias mašinos dalis, sugedusias dėl blogos medžiagos

ar gamyklinio broko. Mes neatsakome už dalis, pagamintas ne mūsų ir jūsų gautas iš kito tiekėjo. Naujų dalių montavimo kaštai yra pirkėjo

atsakomybė. Pirkimo nutraukimas ar pirkimo kainos sumažinimas, kaip ir bet kurios kitos pretenzijos dėl nuostolių nebus patenkinamos.

Ábyrgð (IS)

Augljósar skemmdir verður að tilkynna innan 8 daga frá viðtöku vörunnar. Annars er réttur kaupanda um bætur vegna slíka skemmda ógildur.

Við ábyrgjumst, í tilfelli réttrar meðhöndlunar yr lögbundið ábyrgðartímabil frá afhendingu, að við skiptum um hvern vélarhlut án kostnaðar

sem ónothæfur er vegna gallaðs efnis eða skemmda í framleiðslu innan ákveðins tímabils. Af því er tekur til hluti sem ekki eru framleiddir af

okkur, ábyrgjumst við af því leiti aðeins að við eigum rétt á ábyrgðarkröfum gagnvart birgðasölum. Kostnaður vegna uppsetningar á nýjum

hlutum skal falla í skaut kaupanda. Ógilding sölu eða afsláttur á kaupverði sem og aðrar kröfur vegna skemmda eru undanskildar.

made in China

Scheppach 5901404904 Kasutusjuhend

Kaubamärk: Scheppach

Mudel: 5901404904

Tüüp: Kasutusjuhend

See juhend sobib ka

DECO-XL

Laadige alla PDF

aruanne

teistes keeltes

English: Scheppach 5901404904 User manual

Scheppach 5901404904 Kasutusjuhend

See juhend sobib ka

Scheppach 5901404904 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid