Dante DLC1985 Kasutusjuhend

DLC1981-DLC1982-DLC1985

Color & D/N PTZ Domes

Installation and Operations Manual

Model Number: DLC1981-DLC1982-DLC1985

Description: PTZ Domes Indoor/Outdoor

18x (1/3”), 22x 26x, 30x, 35x, 36x Zoom

CONTENTS

FEATURES ................................................... 4

DECLARATION ........................................... 6

■PRECAUTION .................................. 6

■WARNINGS ...................................... 6

INSTALLATION PREPARATION ............... 7

■TOOL LIST ....................................... 7

■CABLES ............................................ 7

■DIP SWITCH SETTING ................... 7

■CONNECTION DIAGRAM .............. 7

MOUNT TYPE .............................................. 8

■IN-CEILING MOUNT ....................... 8

■SURFACE MOUNT .......................... 8

■WALL MOUNT ................................. 8

■CORNER MOUNT ............................ 9

■POLE MOUNT .................................. 9

■PENDANT MOUNT .......................... 9

INSTALLATION GUIDE ........................... 10

■IN-CEILING MOUNT ..................... 10

■SURFACE MOUNT Error! Bookmark

not defined.

■WALLMOUNT ................................ 12

■CORNER MOUNT .......................... 14

■POLE MOUNT ................................ 16

■PENDANT MOUNT ........................ 18

S Y S T E M C O N N E C T I O N ................... 21

O P E R A T I O N I N S T R U C T I O N ......... 22

■PREHEATING SCREEN ................. 22

■BOOT-UP SCREEN ........................ 22

■ACCESS MAIN MENU ................... 23

M E N U O P E R A T I O N ........................... 24

■SELECTING ITEM.......................... 24

■CHANGING VALUE ...................... 24

■EDITING TITLE .............................. 24

S Y S T E M I N F O ...................................... 25

■SITE INFO ....................................... 25

■ DISPLAY SETUP ........................... 26

■BOOT-UP SCREEN ......................... 26

■PASSWORD .................................... 26

■SET DEFAUT .................................. 27

■ SYSTEM REBOOT ......................... 27

L E N S P A R A M E T E R S ......................... 28

■ ZOOM SPEED ................................ 28

■ DIGITAL ZOOM ............................ 28

■ JOYSTICK AF/AI ........................... 28

■AF RESUME TIME ......................... 28

■AI RESUME TIME .......................... 29

■IRIS ALC ......................................... 29

■IRIS PLC .......................................... 29

■DAY/NIGHT .................................... 29

C A M E R A P A R A M E T E R S ................. 30

■FRAME LIMIT ................................ 30

■SHUTTER ........................................ 30

■EXPOSURE ..................................... 30

■PRESET FREEZE ............................ 30

■WHITE BALANCE .......................... 31

■BLC MODE ..................................... 31

P A N / T I L T P A R A M E T E R S ............... 32

■ AUTO STOP TIME ......................... 32

■ SPEED AMPLIFY ........................... 32

■ PROPORTIONAL P/T .................... 32

■SET NORTH .................................... 32

A U T O R U N N I N G ................................. 33

■PRESET ........................................... 33

■TOUR ............................................... 34

■ PATTERN ....................................... 35

INSTRUCTION

MANUAL

■ CRUISE .......................................... 36

■ZONE ............................................... 37

■PARK TIME .................................... 38

■PRIVACY MASK ............................ 39

■ ALARM .......................................... 40

APPENDIX I : Special Function Operation .. 41

APPENDIX II : DIP SWITCH SETTINGS .. 42

APPENDIX III：WIRE DIAMETER &

TRANSMISSION CHART ..... 47

APPENDIX IV：RS-485 BUS BASIC

KNOWLEDGE ....................... 48

APPENDIX V： TROUBLE SHOOTING .. 50

APPENDIX VI：LIGHTNING PROOF &

SURGE SIGNAL PROOF ...... 51

APPENDIX VII：WARRANTY .................. 52

4

FEATURES

Product Features

 Multiple Zoom camera blocks optional

 Graceful outlook, Vandal proof available

 System preheat in low temperature environment

 Programmable Multi-protocol

 Multi-language menu (China, Britain, France, Germany, Russia,

Italy, Portugal, Spain), friendly interface, easy to operate

 360° continuous pan, 180° Tilt “Auto Flip”

 8 tours(32presets/tour), 8patterns, 8 cruise

 8 Privacy Mask, 8 titled zones

 Port for Software up-grade

 Built-in Alarm, 8 Inputs/4 Outputs

 Built-in Surge and Lightning Protection

 Speed Amplify to fit different control keyboard

 Auto Running Memory Against Power Outage

 Auto Running Resume after Manual Operation

 On-Screen display for compass and tilt angle,

System and environment temperature, fan status

Dome Drive Unit

 360° continuous pan, 180°Tilt “Auto Flip”

 Discreet Liner with Sealed Fixed Bubble

 256 presets, ±0.1° preset accuracy

 320°/s Pan/Tilt 400°/s Preset Speed

 8 tours max. 27 presets/tour

 8 patterns, 4 cruises, 8 titled zones

 8-24 privacy masks

 OSD Menu password protection

 Built-in alarm, 7 input/2 output

 Multiple RS-485 protocol/Coaxial

 Locations of Labels and On-Screen Displays

 Software Up-gradable via RJ-45

 FIFO alarm priority levels

 Alarm driven Pattern, preset etc.

 Position Resume After Alarm

 Variable Cruise Speed 0.1-150°/sec

 OSD Menu for Programmable Functions

 Proportional Pan/Tilt Speed

 Vertical Tilt Unobstructed 0° to -95°

 Auto Running Memory Against Power Outage

 Auto Running Resume after Manual Operation

 System preheat before camera power on

 On-Screen display for compass and tilt angle,

System and environment temperature, fan status

Environment

Operating Temperature

Model

Absolute Max

Sustained Max

Absolute Min

Sustained Min

In

-

Ceiling Indoor

32° to 122°F (0° to 50°C)

Standard Pendant

113°F (45°C)

95°F (35°C)

-

4°F (

-

20°C)

14°F (

-

10°C)

Env

ironmental Mount

1

58

°F (

7

0°C)

1

40

°F (

6

0°C)

-

60°F (

-

51°C)

-

50°F (

-

45°C)

Note:

1. Assume no wind chill factor

2. Prevents icing at sustained minimum of -50°F (-45°C)

3. De-ices 0.1 inch (2.5 mm) within 3 hours after power-up

TECHNICAL SPECIFICATIONS

Electrical

 Input Voltage 16-30 VAC; 24 VAC nominal

 Input Power 10 VA nominal (w/o heater)

 45 VA nominal (with heater)

 Fuse 1.25A

 Auxiliary Outputs 2 Alarm Inputs 7

 Built-in Surge Protection

 Limited Lightning Protection

General

Construction

Back Box & Housing Die-cast Aluminum

Dome Drive Aluminum, thermo

plastic

Bubble Acrylic/Poly Carbon

5

Camera/Options

Accessories

Mounting

 Wall mount bracket

 Pendant mount accessory

 Corner mount accessory

 Pole mount accessory

Heating

 Outside temperature sensor

Transmitting & Controlling

 Up-the-Coax/RS-485 converter

 Manchester Code or Biphase Code/RS-485 converter

Cam. Parameters DLC1982-26X D/N w/ICR DLC1985–30X D/N w/ICR DLC1985–35X D/N w/ICR DLC1985–36X D/N w/ICR

Image Sensor ¼”

Sony CCD

¼ Hitachi CCD ¼” Hitachi CCD ¼” SONY EXview HAD

Resolution 480/570BW TVL 540/650BW TVL 540/650BW TVL 550/680BW TVL

Effective Pixels NTSC 380k / PAL 440k NTSC 410k / PAL 470k NTSC 380k / PAL 410k NTSC 380k / PAL 440k

Signal Format NTSC/PAL NTSC/PAL NTSC/PAL NTSC/PAL

Video Output 1V p-p (sync negative) 1V p-p (sync negative) 1V p-p (sync negative) 1V p-p (sync negative)

Lens 26X SONY

30X Hitachi WDR / Image

Stabilizer

35X Hitachi WDR / Image

Stabilizer

36X Sony WDR / Image

Stabilizer

Focal Length f=3.5mm(W)~91mm(T) f=3.4mm(W)~102mm(T)

f=3.4mm(W)~119mm(T) f=3.4mm(W)~122.4mm(T)

Aperture

F1.6~F3.8

F1.4~F3.6 F1.4~F4.2 F1.4~F4.5

Digital Zoom 12X 12X 12X 12X

Min. Working Dist. 320mm(W)~1500mm(T) 55.8° (Wide) to 2° (Tele) 55.8° (Wide) to 1.7° (Tele) 320mm(W)~1500mm(T)

Sync System internal/external (V-lock) internal/Line-lock internal/external (V-lock) internal/external (V-lock)

S/N Ratio >50dB >50dB >50dB >50dB

Min. Illumination @ 35

IRE 1.0/0.15Lux/BW 0.1/0.01BW/LUX

0.018LUX @ 1/2sec Color /

0.0001LUX @ 1/15sec BW

0.018LUX @ 1/2sec Color /

0.0001LUX @ 1/15sec BW

IRIS Auto/Manual Auto/(offset software) Auto/(offset software) Auto/Manual

Focus Auto/Manual Auto/Manual Auto/Manual Auto/Manual

White Balance Auto/Manual Auto/Manual Auto/Manual Auto/Manual

Gain Auto/Manual 0-30dB via software 0-30dB via software Auto/Manual

BLC / WDR Auto/Manual ON/OFF

ON/OFF

6

DECLARATION

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case the

user will be required to correct the interference at

the user’s own expense.

■

■■

■PRECAUTION

♦ Only qualified and experienced person can

carry out the installation. In many

countries and areas licensed personnel is

required

♦ Always take safety codes into

consideration during installation.

♦ Use reliable tools only, poor quality tools

may cause damage to both human and

property

♦ Check the strength of all item onsite that

are related to installation in advance. It is

recommended that the stand of dome be 8

times stronger than the weight of the dome

and its accessories.

♦ Keep all the original dome package

materials in case of future repacking and

transportation.

♦ Choose and install speed dome according

to environment requirement (Refer to the

Product Features). This product conforms

to IP66 standard as specified in “Housing

Protection Classification (IP code)”.

■

■■

■WARNINGS

♦ Avoid installing this speed dome in

hazardous places where inflammable or

explosive materials are stored or used.

♦ Indoor dome is not designed for outdoor

environment.

♦ This speed dome runs on 24VAC.

♦ Connect to power only after completing

installation.

♦ Disassemble can only be carried out by

qualified personnel.

♦ Use soft towel to clean the lower cover

when necessary. Avoid using caustic

detergent.

♦ Avoid aiming camera to strong light.

7

INSTALLATION

PREPATATION

■

■■

■TOOL LIST

Following tools may be needed for the installation:

♦ Screws and nuts

♦ Philips screw driver

♦ Standard screw driver

♦ Wire scissors

♦ Ladder

♦ Drill

♦ Saw.

■

■■

■CABLES

♦ Video Coaxial Cable

♦ 75Ω

ΩΩ

Ω impedance,

♦ Solid copper wire,

♦ 95% braided copper shield.

Check the max transmission distance referring to the

chart below.

Model

Distance

RG 59/U

750ft(229m)

RG 6/U

1,000ft(305m)

RG 16/U 1,5000ft(457m)

♦ RS-485 Cable

♦ 0.56mm (24AWG) twisted pair wire

■

■■

■DIP SWITCH SETTING

Refer to appendix I:

♦ Protocol and Baud rate

♦ Dome address

♦ Video cable type

♦ Resistor jumper

♦ Alarm output method

■

■■

■CONNECTION DIAGRAM

POWER RS-485 Sensor

AC ：

：：

：24VAC

：

：：

：GROUND

AC ：

：：

：24VAC

NO ：

：：

：NONE

RX- ：

：：

：RS-485 B

RX+ ：

：：

： RS-485 A

S- ：

：：

：Temperature Sensor -

S+ ：

：：

：Temperature Sensor +

Alarm Socket

Alarm In (1-7): Alarm Input (1-7), NC

Alarm In Com: Common port of alarm in

Relay Out (1-2): Alarm relay (1-2), NC or NO

selectable

- 8-

MOUNT TYPE

■

■■

■IN-CEILING MOUNT

■

■■

■SURFACE MOUNT

■

■■

■WALL MOUNT

225

247

16

5

100

225

- 9-

■

■■

■CORNER MOUNT

■

■■

■POLE MOUNT

■

■■

■PENDANT MOUNT

- 10-

INSTALLATION GUIDE

■

■■

■IN-CEILING MOUNT

Maximum thickness of the ceiling is 42mm and the

ceiling should be able to hold 8 times of the weight of

the speed dome. More than 20cm of clear space is

needed above the ceiling.

1. Mark the hole on ceiling.

Mark a φ

φφ

φ225 mm circle on the proper position of

the ceiling using the accessory paper sheet

2. Make the hole.

Cut the hole with proper tool. Make sure the

tolerance is less than +2mm.

225

3. Unfasten the circuit board.

Unscrew the screw to open the circuit board on

connection board.

4. Connect cables.

Prepare wiring and then put Power/RS-485/ Video

cables through waterproof connector on the top of

housing. Turn the connector into the top hole of the

housing

5. Connect cables.

Plug cables into corresponding sockets on circuit

board. When finished, fix the circuit board back

and turn on the power. The red LED will light.

Turn off the power after checking.

NOTE: There are signs for each port. Fix cables as

picture shows. Make sure power is off before

connecting.

- 11-

6. Adjust clips.

Adjust the height of the three mounting clips.

Swing the three mounting clips to adhere to

housing.

7. Install housing.

Push housing into ceiling and let the clips stretch

out. Finally, screw the three clips to tighten the

housing

8. Set dome ID, baud rate and protocol.

Set dome ID, bard rate and protocol by configuring

DIP switches (Refer to APPENDIX I).

NOTE: Remove the packing sponges.

9. Install Pan/Tilt Module.

Push the black liner into the two tabs. Install the

pan/tilt module with two clips, match color of AMP

sockets. Gently push the module upward until

hearing two clicks.

NOTE: Remove the lens cover

10. Install lower cover.

Fasten the safety chain on housing. Align clasps

and mounting holes then turn clock-wise.

NOTE: Let the safety chain inside the arc groove of

the lower cover, otherwise it may scratch the lens.

-12-

■

■■

■WALLMOUNT

Check carefully to make sure the wall is firm and does

not peel off. It is required that the wall can withstand 8

times weight of the dome set.

1. Mark mounting position

Use bracket to mark the mounting position on wall.

2. Install bracket.

Connect all cables through the hole of bracket, and fix

bracket on the wall.

NOTE: Put cables through the wall or aside the

bracket.

3. Release the connection board.

Unscrew to release the circuit board on connection

board.

4. Install housing

Connect cables through the hole on top of the housing.

Align the fast connector to bracket and fix with 2 M5

screws.

NOTE: Apply water-proof tape to the thread in the case

of outdoor dome

5. Connect cables.

Plug cables into corresponding sockets on circuit board.

Reinstall the circuit board and turn on the power. The

red LED is on if connections are correct. Turn off the

power after checking.

NOTE: Names of the interfaces are marked on terminal

block or PCB. Connect cables as picture shows. Make

sure power is off before connecting.

ALARM

VI DEO

RS485, AC24V

-13-

6. Set dome ID, baud rate and protocol.

Set dome ID, bard rate and protocol by configuring

DIP switches (Refer to APPENDIX I).

7. Lower cover preliminary installation.

Attach the safety chain with a M3 nut as picture shows.

8. Install black liner and Pan/Tilt Module.

Push the black liner into the two tabs. Install the pan/tilt

module with two clips, match color of AMP sockets.

Gently push the module upward until hearing the click.

NOTE: Remove the lens cover

Tab

Bl ack Li ner

9. Install lower cover.

Unscrew the two M4 screw on lower cover ring. Push

up the lower cover into the housing and then fasten

lower cover with two M4 screws.

NOTE: Apply lube to the O-ring in the case of outdoor

dome

lube

M4 slot

-14-

■

■■

■CORNER MOUNT

Check carefully to make sure the wall is firm and does

not peel off. It is required that the wall can withstand 8

times weight of the dome set.

1. Mark the fastener positions.

Use the corner mount base as the template to mark

the mounting positions on wall.

2. Install base.

Put Power/RS-485/ Video cables through the hole

of corner mount base and use M8 nuts to fasten

corner base on the mounting surface.

NOTE: Put cables through the wall of aside the

corner base

3. Install bracket.

Put cables through the cavity of bracket and fasten

bracket on base

4. Release the connection circuit board.

Unscrew to release the circuit board on

connection board.

5. Install housing.

Connect cables through the hole on top of the

housing. Align the fast connector to bracket and fix

with 2 M5 screws

NOTE: Apply water-proof tape to the thread in the

case of outdoor dome

-15-

6. Connect cables.

Plug cables into corresponding sockets on circuit

board. Reinstall the circuit board and turn on the

power. The red LED is on if connections are

correct. Turn off the power after checking.

NOTE: Names of the interfaces are marked on

terminal block or PCB. Connect cables as picture

shows. Make sure power is off before connecting

ALARM

VI DEO

RS485, AC24V

7. Set dome ID, baud rate and protocol.

Set dome ID, bard rate and protocol by configuring

DIP switches (Refer to APPENDIX I).

8. Lower cover preliminary installation.

Attach the safety chain with a M3 screw as picture

shows.

9. Install black liner and Pan/Tilt Module.

Push the black liner into the two tabs. Install the

pan/tilt module with two clips, match color of AMP

sockets. Gently push the module upward until

hearing two clicks.

NOTE: Remove the lens cover.

Tab

Bl ack Li ner

10. Install lower cover.

Unscrew the two M4 screws on lower cover ring.

Push up the lower cover into the housing, and then

fasten lower cover with two M4 screws.

NOTE: Apply the lube to the O-ring in the case of

outdoor dome

lube

M4 slot

-16-

■

■■

■POLE MOUNT

Pole mount is applicable to installation on pole with

diameter of 130-150mm (5.12”~6”)

1. Install base.

Put Power/RS-485/ Video cables through the

central hole of the bracket base, and then fix it to

the pole

2. Install bracket.

Put cables through the cavity of bracket and fasten

it on base.

3. Release the circuit board.

Unscrew to release the circuit board on connection

board.

4. Install housing.

Connect cables through the hole on top of the

housing. Align the fast connector to bracket and fix

with 2 M5 screw

NOTE: Apply water-proof tape to the thread in the

case of outdoor dome

5. Connect cables.

Plug cables into corresponding sockets on circuit

board. Reinstall the circuit board and turn on the

power. The red LED is on if connections are

correct. Turn off the power after checking.

NOTE: Names of the interfaces are marked on

terminal block or PCB. Connect cables as picture

shows. Make sure power is off before connecting

ALARM

VI DEO

RS485, AC24V

-17-

6. Set dome ID, baud rate and protocol.

Set dome ID, bard rate and protocol by configuring

DIP switches (Refer to APPENDIX I).

NOTE: Remove the packing sponge.

7. Lower cover preliminary installation.

Attach the safety chain with a M3 screw as picture

shows.

8. Install black liner and Pan/Tilt Module.

Push the black liner into the two tabs. Install the

pan/tilt module with two clips, match color of AMP

sockets. Gently push the module upward until

hearing two clicks.

NOTE: Remove the lens cover.

Tab

Bl ack Li ner

9. Install lower cover.

Unscrew the two M4 screws on lower cover ring.

Push up the lower cover into the housing and then

fasten lower cover with two M4 screws.

NOTE: Apply the lube to the O-ring in the case of

outdoor dome

lube

M4 slot

-18-

■

■■

■PENDANT MOUNT

In case of low ceiling height dome can be mounted

directly into the base flange.

1. Mark the mounting position.

Use the bracket base to mark the fastener positions

on ceiling

2. Install base.

Connect wirings through the central hole of the

bracket base, and then fix it on ceiling.

NOTE: Put silica gel along the top of bracket base

in the case of outdoor dome.

3. Install suspender.

Connect wirings through the cavity of suspender,

and then turn the threaded pipe head into the

bracket base and fasten the connection with a M5

screw.

NOTE: Apply water-proof tape to the thread and

put silica gel to the suspender as picture shows in

the case of outdoor doom.

4. Release the circuit board.

Unscrew to release the circuit board from

connection base

-19-

5. Install housing.

Connect cables through the top hole of the

housing, and then turn the housing thread pipe

head into suspender and fasten the connection

with two M5 screws

NOTE: Apply water-proof tape to the thread in

the case of outdoor dome. If installation height is

not high enough, mount housing directly into the

base.

Tape

Screw

Tape

Screw

6. Connect cables.

Plug cables into corresponding sockets on circuit

board. Reinstall the circuit board and turn on the

power. The red LED is on if connections are

correct. Turn off the power after checking.

NOTE: Names of the interfaces are marked on

terminal block or PCB. Connect cables as picture

shows. Make sure power is off before connecting.

ALARM

VI DEO

RS485, AC24V

7. Set dome ID, baud rate and protocol.

Set dome ID, bard rate and protocol by configuring

DIP switches (Refer to APPENDIX I).

8. Lower cover preliminary installation.

Attach the safety chain with a M3 nut as picture

shows.

lube

M4 slot

Leht laadib ...

Dante DLC1985 Kasutusjuhend

See käsiraamat sobib ka

Dante DLC1985 Kasutusjuhend

teistes keeltes

Muud dokumendid