Piaa 15211 paigaldusjuhend

Bränd
Piaa
Mudel
15211
Tüüp
paigaldusjuhend
Thank you very much for purchasing PIAA product.
Please read these instructions before installation
and use of this product.
• Installation of this bulb is simple, just reverse the steps you took to
remove your old bulbs.
• Before installation make sure that your lamps and wiring harness are
compatible with this bulb.
Things to check prior to installation:
1. Lamp must take the same style bulb as the one you are
attempting to install.
2. Lamp must be able to dissipate the heat created by this
upgrade.
* Higher wattage bulbs will generate more heat.
3. The bulb seat must be clean.
4. The connector that plugs into the bulb must be clean.
5. The harness cannot be damaged.
6. If you are installing a higher wattage bulb you must check to
see if the relay harness is capable of the extra amperage.
If any of the above listed are not checked and fixed this bulb will not
perform and if they are not fixable you cannot use this bulb
Bulb Instruction Manual
1. Turn off vehicle, set parking brake, and disconnect negative
battery cable.
2. Locate the bulb(s) you wish to replace.
3. Remove the plug from the harness that connects to the
back of the bulb.
4. Remove the clip(s) and or spring that holds the bulb
in the lamp.
5. Carefully remove bulb, do not touch or bump it on anything
if you plan on reusing it later. Do not break bulb, it is under
pressure and may burst causing personal injury.
6. Remove the new PIAA bulb from its container, touching
only the metal or plastic base.
7. Insert the new bulb in the reverse of how you removed the
old bulb.
8. Make sure you insert the bulb all the way into the bulb seat
at the back of the lamp.
9. Fasten the clip(s) or spring that holds the bulb in place.
10. Make sure the connector is clean and undamaged then plug
it into the back of the bulb.
11. Reconnect negative battery cable.
INSTALLATION
For detailed instructions on your vehicle
consult your vehicle owner's manual.
1. Start vehicle and turn on lights and test them.
2. The first test is to turn on the low beam and go to the
front of the lamp and check that it is the low beam filament
that is on and that the high beam is turned off.
3. The second test is to turn on the high beam and go to the
front of the lamp and check that it is the high beam filament
that is on and that the low beam is turned off.
Notice: Some bulbs only have one fillament. in this situation
there is only on and off
4. Turn off lights and stop vehicle.
5. If the test reveals that the bulbs are not working properly,
seek assistance from your local PIAA dealer.
6. If the bulbs are working, you are ready to start using and
enjoying your new PIAA bulbs.
TESTING
BULBS
H1
H4
H3
HB3
9005
HB4
9006
HB5
9007
HB1
9004
• NEVER touch the glass tube with anything including your
hands as residue and/or oils will greatly reduce the life span
of the bulb. Oils may actually cause the bulb to burst when
turned on. If you do get a substance on the bulb you must
clean it thoroughly with a cleaner that leaves no oil or residue
such as an alcohol cleaner, before turning the bulb on.
• NEVER turn on the bulb when it is not fastened into the
lamp. This is because if there happens to be a substance on
the glass part of the bulb it may burst causing personal injury.
• NEVER do anything to the bulb that may cause it to break.
This is because the glass tube is under pressure and may
burst causing personal injury.
Contact your dealer regarding
PIAA’s Limited Warranty.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Piaa 15211 paigaldusjuhend

Bränd
Piaa
Mudel
15211
Tüüp
paigaldusjuhend
Laadige alla PDF
aruanne

teistes keeltes

Muud dokumendid