HP LaserJet 3300 Multifunction Printer series Kasutusjuhend

hp LaserJet 3300

Fax

Faksi

English

hp LaserJet 3330mfp

fax guide

Hewlett-Packard Company

11311 Chinden Boulevard

Boise, Idaho 83714 U.S.A.

Copyright Information

Company

Reproduction, adaptations, or

translation without prior written

permission is prohibited except

as allowed under copyright laws.

Part number C9126-90921

First edition, September 2001

Warranty

The information contained in

this document is subject to

change without notice.

Hewlett-Packard makes no

warranty of any kind with

respect to this information.

HEWLETT-PACKARD

SPECIFICALLY DISCLAIMS

THE IMPLIED WARRANTY OF

MERCHANTABILITY AND

FITNESS FOR A PARTICULAR

PURPOSE.

Hewlett-Packard shall not be

liable for any direct, indirect,

incidental, consequential, or

other damage alleged in

connection with the furnishing or

use of this information.

NOTICE TO U.S.

GOVERNMENT USERS:

RESTRICTED RIGHTS

COMMERCIAL COMPUTER

SOFTWARE: “Use, duplication,

or disclosure by the

Government is subject to

restrictions as set forth in

subparagraph (c) (1)(ii) of the

Rights in Technical Data Clause

at DFARS 52.227-7013.”

Safety Information

WARNING!

Potential Shock Hazard

Always follow basic safety

precautions when using this

product to reduce risk of injury

from fire or electric shock.

1 Read and understand all

instructions in the

electronic user guide.

2 Observe all warnings and

instructions marked on the

product.

3 Use only a grounded

electrical outlet when

connecting the

HP LaserJet 3330 product

to a power source. If you

do not know whether the

outlet is grounded, check

with a qualified electrician.

4 Do not touch the contacts

on the end of the

telephone cord or any of

the sockets on the

HP LaserJet 3330 product.

Replace damaged cords

immediately.

5 Never install telephone

wiring during a lightning

storm.

6 Unplug this product from

wall outlets and telephone

jacks before cleaning.

7 Do not install or use this

product near water or

when you are wet.

8 Install the product securely

on a stable surface.

9 Install the product in a

protected location where

no one can step on or trip

over the telephone line and

the telephone line will not

be damaged.

10 If the product does not

operate normally, see the

electronic user guide.

11 Refer all servicing

questions to qualified

personnel.

Information regarding FCC

Class B, Parts 15 and 68

requirements and other

regulatory requirements can be

found in the electronic user

guide.

Trademark Credits

Microsoft®, Windows®, and

Windows NT® are U.S.

registered trademarks of

Microsoft Corporation.

All other products mentioned

herein may be trademarks of

their respective companies.

Local country laws may prohibit

the use of this product outside

of the countries specified. It is

strictly forbidden by law in most

countries to connect

nonapproved

telecommunications equipment

(fax machines) to public

telephone networks.

ENXC 3

Contents

1 Setting up

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connecting the product to a phone line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

To connect the product to a phone line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting additional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

To connect additional devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Specifying the fax settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

To enter text from the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

To set the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

To set the fax header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setting the answer mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

To set the answer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setting rings-to-answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Recommended rings-to-answer table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

To set the number of rings-to-answer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Enabling answer ring patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

To enable answer ring patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Faxing (basic)

Loading originals to fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

To load fax documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Sending faxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

To send a fax to one recipient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Changing the default contrast and resolution for outgoing faxes . . . . . . . . . . . . 16

To change the default contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

To change the default resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Deleting faxes from memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

To delete faxes from memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Sending faxes from the software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

To send a fax from the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 Faxing (advanced)

About speed-dial codes, one-touch keys, and group-dial codes. . . . . . . . . . . . . 19

To program speed-dial codes and one-touch keys. . . . . . . . . . . . . . . . . . . . 19

To delete speed-dial codes and one-touch keys . . . . . . . . . . . . . . . . . . . . . 20

To quickly program speed-dial codes or one-touch keys . . . . . . . . . . . . . . . 21

To program a one-touch key for alternate long distance . . . . . . . . . . . . . . . 21

To manage group-dial codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

To program group-dial codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

4 ENXC

To delete group-dial codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

To delete an individual from a group-dial code. . . . . . . . . . . . . . . . . . . . . . . 23

To delete all phone book entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Using dialing characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

To insert a pause or wait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Inserting a dial prefix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

To set the dial prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Enabling an extension phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Using manual dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

To use manual dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Printing the fax activity log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

To print the fax activity log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Changing the fax call report print times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

To set fax call report print times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4 Troubleshooting

Is your fax set up correctly? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

What type of phone line are you using? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Are you using a surge protection device?. . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Are you using a phone company voice messaging service? . . . . . . . . . . . . 30

Are you using an answering machine?. . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

General fax problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Receiving fax problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Sending fax problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Accessing the electronic user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

To access the electronic user guide from the product software . . . . . . . . . . 38

To access the electronic user guide from the product CD-ROM . . . . . . . . . 38

ENXC Introduction 5

English

1

Setting up

Introduction

Congratulations on your purchase of the HP LaserJet 3330mfp, a

powerful business tool with the capabilities of a full range of office

equipment. You can use the product to fax, print, copy, and scan.

This guide was written to describe the fax functions of this product and

to help you complete the following tasks:

● Connect your product to a phone line

● Connect additional devices

● Specify your fax settings

● Set the answer mode and rings-to-answer

● Enable answer ring patterns

We recommend that you save this Fax Guide so you can refer back to

instructions on specific fax features.

If you need general setup instructions for your product, such as

instructions for installing the print cartridge, installing the media input

trays and the automatic document feeder (ADF) input tray, installing the

product software, and connecting the product to a network, please see

the getting started guide that came with the product.

Connecting the product to a phone line

The first step toward using your fax is connecting the product to the

phone line.

Note In order for the product to fax correctly, it must be the first device connected

to the phone jack.

6 Chapter 1 Setting up ENXC

To connect the product to a

phone line

Use these steps to connect the product to a

phone line, even if you have two telephone

numbers on that line and use a ring pattern

service (such as distinctive ring).

1 If a phone cord is plugged into the phone

jack, unplug the cord and set it aside.

2 Open the print cartridge door and swing

open the left side panel to reveal the

phone line sockets.

3 Take the phone cord included with the

product and plug one end of it into the

product’s line socket (the socket on top).

Note

You must use the phone cord that came with

the product in order for the product to

function correctly.

1

3

2

ENXC Connecting additional devices 7

English

4 Close the left side panel and the print

cartridge door. When closing the left side

panel, ensure the phone line is routed

through the upper notch in the panel.

5 Plug the other end of the phone cord into

the phone jack on the wall.

If you want to connect additional devices,

such as a phone, to the phone line, continue

to “Connecting additional devices” on page 7.

If you do not want to connect other devices,

continue to “Specifying the fax settings” on

page 10.

Connecting additional devices

Depending on the setup of your phone lines, you can connect additional

devices to the phone line along with your HP LaserJet 3330.

As a general rule, no more than three or four devices should be

connected to a single phone line. If too many devices are connected to a

single phone line, one or more of the devices may not detect an

incoming call. If this occurs, disconnect one or more of the devices.

Note The HP LaserJet 3330 cannot replace a computer modem. It will not act

as a data modem for sending and receiving e-mail, connecting to the

Internet, or communicating with other computers.

Dedicated fax line

If you connected your HP LaserJet 3330 to a phone line that is used only

for fax calls, you may want to connect the following devices:

● Modem: You can connect a computer modem (external or internal)

to the fax line if you want to use the fax line for e-mail or for access

to the Internet, but you cannot send or receive faxes while using the

line for these purposes.

● Extra phone: You can connect an extra phone to the fax line if you

want to make outgoing calls on the fax line.

You should not connect the following devices:

● Answering machine or computer voicemail: If you use computer

voicemail, you must connect a modem (external or internal) to your

dedicated voice line. Then, use the dedicated voice line to connect

to the Internet and receive voicemail.

5

4

8 Chapter 1 Setting up ENXC

Shared phone line

If you connected your HP LaserJet 3330 to a phone line that is shared

between fax calls and voice calls, or if you have one phone line with two

phone numbers and a ring pattern service, you may want to connect the

following devices:

● Modem: You can connect a computer modem (external or internal)

to the shared line if you want to use the shared line for e-mail or for

access to the Internet, but you cannot send or receive faxes while

using the line for these purposes.

● Phone: You can connect a phone to the shared line if you want to

make or receive voice calls on the shared line.

● Answering machine or computer voicemail: You should connect

these devices to the same phone jack as the product to make sure

the different devices do not interfere with one another.

Note It is possible to connect devices to another phone jack for the same phone

line (in another room, for example); however, the devices may interfere

with faxing and with each other.

ENXC Connecting additional devices 9

English

To connect additional devices

Connect additional devices in the order

shown. If you do not want to connect a

device, skip it and continue to the next

device.

1 Unplug the power for all devices you

want to connect.

2 If you have not yet connected your

product to a phone line, see “Connecting

the product to a phone line” on page 5

before proceeding. The product should

already be connected to a phone jack.

3 To connect an internal or external

modem on a computer, plug its phone

line connector into the wall jack, on top

of the product’s connector.

4 To connect an answering machine, plug

its phone line connector into the wall

jack, on top of the previous device’s

connector.

5 To connect a phone, plug its phone line

connector into the wall jack, on top of the

previous device’s connector.

6 After you have finished connecting

additional devices, plug all of the devices

into their power sources.

3

4

5

2

10 Chapter 1 Setting up ENXC

Specifying the fax settings

Before you can begin using your product’s fax features, you must

complete the following tasks:

● Set the time and date

● Set your fax header

● Set the answer mode

● Set rings-to-answer

● Enable answer ring patterns, if needed

Note If you will be installing the product software on your computer, you can

skip the remaining instructions in this chapter. The software install will

automatically walk you through setting up the fax settings. See the getting

started guide for instructions.

Note In the U.S. and many other regions, setting the time, date, and other fax

header information is a legal requirement.

To enter text from the control panel

Use the following instructions to enter information from the product’s

control panel with the alphanumeric keypad and the < and > buttons:

● Numbers: To enter numbers, press the numeric button for the

number you need.

● Letters: To enter letters, repeatedly press the numeric button for the

letter you need until that letter appears (for example, if the first letter

you need is a “C,” press 2 repeatedly until a “C” appears in the

control panel display).

● Punctuation marks: To enter punctuation marks, repeatedly press

* until the character you want appears in the control panel display.

● Spaces: After entering any character, press > twice to create a

space after that character and move the cursor to an insertion point

after the space.

● Errors: If you enter a character incorrectly, use the < button to

erase the incorrect character, then enter the correct character.

To set the time and date

To set or change the time and date, use the following steps. If you need

help entering any information, see “To enter text from the control panel”

on page 10.

1 On the control panel, press menu/enter.

2 Using the < and > buttons, select Time/Date, Header, and press

menu/enter.

ENXC Setting the answer mode 11

English

3 Press menu/enter to select Time/Date.

4 Using the < and > buttons, specify either the 12-hour or the 24-hour

clock, and press menu/enter.

5 Using the alphanumeric keypad, enter the current time.

6 If you specified the 12-hour clock, use the < and > buttons to move

the cursor past the fourth character. Select 1 for a.m. or 2 for p.m.,

and press menu/enter.

OR

If you specified the 24-hour clock, press menu/enter.

7 Using the alphanumeric keypad, enter the current date.

• Make sure you use two digits to specify the month and day (for

example, use “05” for May and “01” for the first day of the month).

8 Press menu/enter.

To set the fax header

To set or change the fax header information, use the following steps. If

you need help entering any information, see “To enter text from the

control panel” on page 10.

1 On the control panel, press menu/enter.

2 Using the < and > buttons, select Time/Date, Header, and press

menu/enter.

3 Using the < and > buttons, select Fax Header, and press

menu/enter.

4 Using the alphanumeric keypad, enter your fax number, and press

menu/enter.

5 Using the alphanumeric keypad, add the name of your company,

and press menu/enter.

Setting the answer mode

Depending on your situation, you can set the HP LaserJet 3330’s

answer mode to automatic or manual.

● Automatic: In automatic answer mode, the product answers

incoming calls after a specified number of rings or upon recognition

of special fax tones. To specify the number of rings, see “Setting

rings-to-answer” on page 12.

● Manual: In manual answer mode, the product never answers calls.

You must start the fax-receiving process yourself, either by pressing

start fax on the control panel or by picking up a phone connected to

that line and dialing 1-2-3.

The default answer mode is automatic.

12 Chapter 1 Setting up ENXC

Note Although most users leave answer mode set to automatic, voice callers

who dial the fax phone number will hear fax tones if the phone is not

answered, or if they do not hang up by the specified number of

rings-to-answer. If you do not want voice callers to hear fax tones, use the

manual setting, but remember that fax calls are not received automatically.

To set the answer mode

To set or change the answer mode, use the following steps:

1 On the control panel, press menu/enter.

2 Using the < and > buttons, select Fax Setup, and press

menu/enter.

3 Using the < and > buttons, select Fax Recv. Setup, and press

menu/enter.

4 Press menu/enter to select Answer Mode.

5 Using the < and > buttons, select Automatic or Manual, and press

menu/enter.

6 The control panel display shows the answer mode setting that you

specified.

Setting rings-to-answer

When the answer mode is set to automatic, the product’s

rings-to-answer setting determines the number of times the phone rings

before an incoming call is answered.

If the product is connected to a line receiving both fax and voice calls (a

shared line) with an answering machine, you may need to adjust the

rings-to-answer. The number of rings-to-answer for the product must be

greater than the rings-to-answer on the answering machine. This allows

the answering machine to answer the incoming call and record a

message if it is a voice call. When the answering machine answers the

call, the product listens to the call and automatically answers it if it

detects fax tones.

The default setting for rings-to-answer is two.

ENXC Setting rings-to-answer 13

English

Recommended rings-to-answer table

Use the following table to determine the number of rings-to-answer to

use.

To set the number of rings-to-answer

To set or change the number of rings-to-answer, use the following steps:

1 On the control panel, press menu/enter.

2 Using the < and > buttons, select Fax Setup, and press

menu/enter.

3 Using the < and > buttons, select Fax Recv. Setup, and press

menu/enter.

4 Using the < and > buttons, select Rings To Answer, and press

menu/enter.

5 Using the alphanumeric keypad, enter the number of

rings-to-answer, and press menu/enter.

Type of phone line Recommended rings-to-answer

Dedicated fax line (receiving

only fax calls)

Leave at two rings

One line with two separate

numbers and ring pattern

service

Leave at two rings.

(If you have an answering machine or computer

voicemail for the other phone number, make sure the

product is set to a lesser number of rings than the

answering system. Also, see “Enabling answer ring

patterns” on page 14.)

Shared line (receiving both fax

and voice calls) with only an

attached phone

Set to five rings.

Shared line (receiving both fax

and voice calls) with an attached

answering machine or computer

voicemail

Two rings more than the answering machine or

computer voicemail. (You cannot set the product to

more than seven rings in Sweden and Finland.)

14 Chapter 1 Setting up ENXC

Enabling answer ring patterns

Ring pattern or distinctive ring service is available through some local

phone companies and allows you to have more than one phone number

on a single line. Each phone number has a unique ring pattern, allowing

you to answer voice calls and the product to answer fax calls.

If you subscribe to a ring pattern service with your phone company, you

must set the product to answer the correct ring pattern.

Note If you do not have ring pattern service and you change the ring pattern

settings to something other than All Rings, the product might not be able

to receive faxes.

To enable answer ring patterns

To enable answer ring patterns, use the following steps:

1 On the control panel, press menu/enter.

2 Using the < and > buttons, select Fax Setup, and press

menu/enter.

3 Using the < and > buttons, select Fax Recv. Setup, and press

menu/enter.

4 Using the < and > buttons, select Answer Ring Type, and press

menu/enter.

5 Using the < and > buttons, select the ring pattern you want, and

press menu/enter.

6 After product installation is complete, ask someone you know to

send you a fax in order to verify that the ring pattern service is

working correctly.

ENXC Loading originals to fax 15

English

2

Faxing (basic)

This chapter will present some of the basic faxing features available on

your HP LaserJet 3330. For complete information on all fax features, as

well as information about all other product features, refer to the

electronic user guide that came on your product CD-ROM. For

instructions on accessing the electronic user guide see “Accessing the

electronic user guide” on page 38.

Loading originals to fax

Use the following instructions to load original documents for faxing.

To load fax documents

1 Before loading the fax documents into the ADF input tray, make sure

there is nothing on the scanner glass.

2 Put the top ends of the document to be faxed print side up in the

ADF input tray with the first page to be scanned at the top of the

stack.

3 Push the document up against the side of the ADF input tray.

4 Slide the document into the ADF input tray until it does not move

any farther.

The document is now ready to be faxed.

Sending faxes

To send a fax to one recipient

Note If you want to improve the quality of a paper document before faxing it,

scan the document, straighten or clean the image, and send it as a fax

from the software. For more information, see the electronic user guide.

1 Dial the fax number using one of the following methods:

• Use the alphanumeric keypad on the product’s control panel.

• If the fax number you are calling has been assigned to a

one-touch key, press that key.

16 Chapter 2 Faxing (basic) ENXC

• If the fax number you are calling has a speed-dial code, press

speed dial, enter the speed-dial code using the alphanumeric

keypad, and press menu/enter.

Note When dialing with the alphanumeric keypad, include any pauses or other

needed numbers, such as an area code, an access code for numbers

outside a PBX system (usually a 9 or 0), or a long-distance prefix. For

more information, see “Using dialing characters” on page 24.

2 Load the document into the ADF input tray.

3 Adjust any fax settings, such as resolution.

4 Press fax/send.

When the last page of the fax has exited the product, you can start

sending another fax, copying, or scanning.

To fax to numbers you use regularly, you can assign a one-touch key or

speed-dial code. See “To program speed-dial codes and one-touch

keys” on page 19 and “To program group-dial codes” on page 22. If you

have electronic phone books available, you may be able to use them for

selecting recipients. Electronic phone books are generated with

third-party applications.

Changing the default contrast and resolution for

outgoing faxes

The contrast affects the lightness and darkness of an outgoing fax as it

is being sent. Resolution affects the sharpness of outgoing faxes. It also

affects the transmission speed of faxes.

To change the default contrast

The default contrast is the contrast normally applied to items being

faxed. The slider is set to the middle as the default contrast setting.

1 Press menu/enter.

2 Use the < or > button to select Fax Setup and press menu/enter.

3 Use the < or > button to select Fax Send Setup and press

menu/enter.

4 Use the < or > button to select Def. Light/Dark.

5 Use the < button to move the slider to the left to make the fax lighter

than the original, or use the > button to move the slider to the right

to make the fax darker than the original.

6 Press menu/enter to save your selection.

ENXC Deleting faxes from memory 17

English

To change the default resolution

Resolution affects the quality, in dots per inch, of documents to be faxed.

It also affects the transmission speed.

Use this procedure to change the default resolution for all faxes.

1 Press resolution to display the current resolution setting.

2 Use the < or > button to display the desired resolution setting.

3 Press menu/enter to save the selection.

Deleting faxes from memory

Use this procedure only if you are concerned someone else has access

to your product and will try to reprint faxes from the reprint memory.

CAUTION In addition to clearing the reprint memory, this procedure clears any fax

currently being sent, unsent faxes pending redial, faxes scheduled to be

sent at a future time, and faxes not printed or forwarded.

To delete faxes from memory

1 Press menu/enter.

2 Press > once to display Fax Functions and press menu/enter.

3 Use the < or > button to select Clear Saved Faxs, and press

menu/enter.

4 Press menu/enter to confirm the deletion.

Sending faxes from the software

This section and the following section contain some instructions about

sending and receiving faxes using the software that came with the

product. All other software-related topics are covered in the software

help, which can be accessed from the software program’s Help menu.

Note The HP LaserJet Director and HP LaserJet Document Manager are not

supported for Microsoft Windows 95. If you use Windows 95, you can send,

but not receive, faxes with the software. However, all fax features are

available from the control panel.

You can fax electronic documents from your computer in the following

situations:

● The HP LaserJet product is connected directly to your computer or

connected to your computer over a network using an HP Jetdirect

print server.

18 Chapter 2 Faxing (basic) ENXC

Note See the getting started guide for a complete list of supported HP Jetdirect

print servers.

● The product software is installed on your computer.

● You are using Microsoft Windows 98, ME, NT 4.0 SP3, 2000, or XP,

or Mac OS 9.1 or X.

To send a fax from the software

The procedure for faxing jobs from the software may vary; the most

typical steps are shown here.

1 Select a document to fax using one of the following methods:

• Open the document in the HP LaserJet Document Manager on

Windows-compatible computers.

• Open the document in the HP LaserJet Workplace on

Macintosh-compatible computers.

• Open a document in a Windows application such as Microsoft

Word. From the application, select Print from the File menu,

then select HP LaserJet Series Fax from the Printer Name

drop-down list in the print dialog box. Click OK.

• Load the document into the ADF input tray.

2 Add one or more recipients on the HP LaserJet Send Fax dialog

box.

3 Include a cover page (optional).

4 Click Send Now.

OR

Click Send Later and select a date and time.

For more information on sending a fax using the HP LaserJet Workplace

(Mac OS), the HP LaserJet Document Manager (Windows), or the HP

LaserJet Director, see the electronic user guide.

Leht laaditakse ...

HP LaserJet 3300 Multifunction Printer series Kasutusjuhend

HP LaserJet 3300 Multifunction Printer series Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid