(
EMC, LVD
)
S1
Instruction Manual
www.rodemic.com
www rodemic co
m
048-950-2-1_S1_manual.indd 1048-950-2-1_S1_manual.indd 1 2/07/2009 12:28:28 PM2/07/2009 12:28:28 PM
- 2 -
Introduction
The S1 is the result of over 30 years experience in stage
sound technology.
The design brief was simple- build the best vocal mic
in the world! How do you achieve that? Well, you need
to have a sound quality that is equal to the fi nest studio
microphones, and certainly
has the experience
to make this happen!
The studio quality is a great start, but for live use the
microphone must not suffer from feedback, handling or
plosive noise. It must also have a tailored response that
takes into consideration the proximity effect. What else?
It must be able to take the knocks and bumps of the
road! The S1 does it all, and in my opinion, is the best
looking vocal mic around.
While using the S1 is quite simple, and there are not
many things you need to learn, please take a moment
to read through this user manual, and then visit
www.rodemic.com and register your microphone for a
full ten year warranty.
While there you can view studio tips and techniques, as
well as browse the comprehensive range of accessories
for
microphones. Thank you for investing in your
S1 live condenser microphone.
Peter Freedman
Microphones
Sydney Australia
048-950-2-1_S1_manual.indd 2048-950-2-1_S1_manual.indd 2 2/07/2009 12:28:39 PM2/07/2009 12:28:39 PM
- 3 -
Specifi cations
Acoustic
Principle:
Pressure gradient
Directional
Pattern:
Super Cardioid
(See graph)
Frequency
Range:
20 Hz - 20 kHz
(see graph)
Output
Impedence:
50
Sensitivity: -46 dB re 1 Volt/Pascal (5 mV @
94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise: 18 dB SPL
(A - weighted per IEC651)
Maximum
Output:
+12.5dBu (@ 1kHz, 0.7% THD
into 1K load)
Dynamic Range: 132 dB
(per IEC651, IEC268-15)
Maximum SPL: 151dB SPL (@ 1kHz, 0.7% THD
into 1K load)
Signal/Noise: 75 dB SPL
(A - weighted per IEC651)
Power
Requirement:
P48 (48V) phantom supply
Output
Connection:
3-Pin XLR
Net Weight: 308gm
048-950-2-1_S1_manual.indd 3048-950-2-1_S1_manual.indd 3 2/07/2009 12:28:40 PM2/07/2009 12:28:40 PM
- 4 -
Specifi cations
Frequency Response
Polar Response
Accessories
10
0
-10
-20
-30
-40
20Hz 100 1000 10 000 20 000
äÂ
ä ÓÇäÂ
£näÂ
Ó°ä
Óä°ä
Ê£ä°äÊÊ
ä°ä
Ó°ä
{°ä
È°ä
n°ä
£ä°ä
£Ó°ä
£{°ä
£È°ä
£n°ä
Óä°ä
ÓÓ°ä
Ó{°ä
Óx°ä
`ÊÀi°Ê£6É*>
³x°ä
ÀiµÕiVÞ\
Ê xääÊâ\
£äääÊâ\
{äääÊâ\
–
–
–
RM1 Stand mount ZP1 Zip pouch
048-950-2-1_S1_manual.indd 4048-950-2-1_S1_manual.indd 4 2/07/2009 12:28:40 PM2/07/2009 12:28:40 PM
- 5 -
Features
• Studio recording-quality specifi cation
• Supercardioid polar pattern
• Rugged all-metal construction
• Attractive satin nickel/black fi nish.
• Heat treated high strength mesh head
• Custom designed internal plosives screen
• Low handling noise
• Made in Australia
• 10 Year warranty*
*Online product registration required.
048-950-2-1_S1_manual.indd 5048-950-2-1_S1_manual.indd 5 2/07/2009 12:28:44 PM2/07/2009 12:28:44 PM
- 6 -
• The S1 is a phantom powered microphone. To
operate correctly it requires a 48V phantom supply
from the mixing console, PA head or other source.
• It is recommended that you use a high-quality
microphone lead, and keep it as short as practical
for your stage set up. This will ensure the highest
quality sound reproduction.
• When using stage monitors, set them up as shown
below. This will direct the sound to your ears and
towards the least responsive part of the S1’s pick
up pattern.
While PA set up is well beyond this manual, if you
want to get the best sound possible with the least
problems, we recommend a book by Australian
audio legend Duncan Fry, titled “Live Sound
Mixing”.
Using the S1
048-950-2-1_S1_manual.indd 6048-950-2-1_S1_manual.indd 6 2/07/2009 12:28:45 PM2/07/2009 12:28:45 PM
A quick tip to reduce feedback - never put your
hands over the ball head. This can signifi cantly
change the pick-up area of the mic, and can cause
feedback. And of course, never point the front of
mic at the speakers!
• The ball head of the S1 is an engineering marvel.
Made up of fi ve separate mesh screens the outer
is heat-treated steel, which has been bead-blasted
and nickel-plated. Internally we have stainless steel
meshes as well as a fi nal nylon mesh. These fi lters
are design to remove vocal plosives, while not
affecting the frequency response. The mesh head
can be unscrewed and washed in soap and water.
Please fully dry the head before re-assembly and
be sure to take care with the mic once the head has
been removed.
• After use the S1 should be wiped with a dry, soft
cloth and placed in its protective case.
• Be sure to place the moisture-absorbent crystals
(supplied) at the head of the microphone, so as to
absorb any moisture present.
• Eventually this pack of crystals will need to be
dried. This is indicated by the crystals turning pink
in colour.
• They can easily be re-used by placing them in an
oven at 100 - 150 degrees celsius for approximately
ten minutes. The crystals will operate effectively
again once they have turned blue.
- 7 -
Using the S1
Storage
048-950-2-1_S1_manual.indd 7048-950-2-1_S1_manual.indd 7 2/07/2009 12:28:46 PM2/07/2009 12:28:46 PM
- 8 -- 8 -
Warranty
All microphones are warranted for one year
from date of purchase. You can extend that to a full
ten years if you register online at www.rodemic.com.
The warranty covers parts and labour that may be
required to repair the microphone during the warranty
period. The warranty excludes defects caused by
normal wear and tear, modifi cation, shipping damage,
or failure to use the microphone as per the instruction
guide.
If you experience any problem, or have any questions
regarding your
microphone, fi rst contact the
dealer who sold it to you. If the microphone requires a
factory authorised service, return will be organised by
that dealer.
We have an extensive distributor/dealer network, but
if you have diffi culty getting the advice or assistance
you require, do not hesitate to contact us directly.
Microphones
International
PO Box 6685
Silverwater NSW 2128 Australia
Ph: +61 2 9648 5855
Fax: +61 2 9648 2455
USA
P.O. Box 4189
Santa Barbara, CA 93140-4189
Ph: 805 566 7777
Fax: 805 566 0071
Technical Support
For information and technical support questions contact:
support@rodemic.com
In the Unites States and Puerto Rico, contact
usasupport@rodemic.com or call 425 398-1910
In Australia, contact ozsupport@rodemic.com or call (02) 9648 5855
Anywhere except Australia, the United States and Puerto Rico,
contact support@rodemic.com or call +61 2 9648 5855
048-950-2-1_S1_manual.indd 8048-950-2-1_S1_manual.indd 8 2/07/2009 12:28:47 PM2/07/2009 12:28:47 PM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
teistes keeltes
- italiano: Rode S1 Manuale utente
- English: Rode S1 User manual
Muud dokumendid
-
Videk 2996AS-10GY Teabelehe
-
Beyerdynamic Classis GM 305 Kasutusjuhend
-
Zoom R24 Kasutusjuhend
-
Poly VoiceStation 500 Kasutusjuhend
-
Pioneer VSX-531D Kasutusjuhend
-
Yamaha DM-105 Omaniku manuaal
-
Philips D 8279 Kasutusjuhend
-
Cochlear Wireless phone clip Kasutusjuhend
-
Mee Audio Bluetooth Wireless Media Headphones Kasutusjuhend
