Beko BU 1100 HCA Kasutusjuhend

Koelkast

Manuel d'utilisation

48 4976 0005/BA

1/7

BU 1100 HCA - BU 1101 - BU1103N

EN / DE / NL / FR

Kühlschrank/Gefrierschrank

Bedienungsanleitung

Gebruiksaanwijzing

Réfrigérateur

Refrigerator

User manual

Please read this user manual first!

Dear Customer,

We hope that your product, which has been produced in modern plants and

checked under the most meticulous quality control procedures, will provide you an

effective service.

Therefore, read this entire user manual carefully before using the product and

keep it as a reference. If you handover the product to someone else, give the user

manual as well.

The user manual will help you use the product in a fast and safe way.

• Read the manual before installing and operating the product.

• Make sure you read the safety instructions.

• Keep the manual in an easily accessible place as you may need it later.

• Read the other documents given with the product.

Remember that this user manual is also applicable for several other models.

Differences between models will be identified in the manual.

Explanation of symbols

Throughout this user manual the following symbols are used:

CImportant information or useful tips.

AWarning against dangerous conditions for life and property.

BWarning against electric voltage.

EN

2

1 Your Refrigerator 3

2 Safety and Environment

Instructions 4

General Safety ............................................4

Intended Use ...............................................6

Child Safety .................................................. 7

Compliance with WEEE Directive and

Disposing of the Waste Product ......... 7

Compliance with RoHS Directive......... 7

Package Information ................................ 7

3 Installation 8

Points to be paid attention to when the

relocation of the refrigerator ...............8

Electrical connection ...............................8

Disposing of the packaging ...................9

Disposing of your old refrigerator ......9

Placing and Installation...........................9

Placing the refrigerator under the

counter and adjusting the legs ..........10

4 Preparation 11

5 Using your refrigerator 12

Temperature setting button ..............12

Defrost .........................................................12

Changing the illumination lamp .......13

6 Maintenance and

cleaning 14

Protection of plastic surfaces ...........14

7 Troubleshooting 15

CONTENTS

EN

3

1 Your Refrigerator

1. Body shelves

2. Bulb thermostate box

3. Sliding crisper cover

4. Food storage cabin

5. Adjustable front legs

6. Egg compartment

7. Door shelf

8. Bottle shelf

C The figures in this manual are schematic, and they may not be in exact

accordance with your product. If the product you purchased does not have the

related parts, then they are valid are for other models.

2

1

3

4

6

8

7

5

EN

4

2 Safety and Environment Instructions

This section provides the safety

instructions necessary to prevent the

risk of injury and material damage.

Failure to observe these instructions

will invalidate all types of product

warranty.

Intended use

A

WARNING:

Keep ventilation openings,

in the appliance enclosure or

in the built-instructure, clear

of obstruction.

A

WARNING:

Do not use mechanical

devices or other

means to accelerate the

defrostingprocess, other

than those recommended

by the manufacturer.

AWARNING:

Do not damage the

refrigerant circuit.

A

WARNING:

Do not use electrical

appliances inside the food

storage compartments

of the appliance, unless

they are of the type

recommended by the

manufacturer.

A

WARNING:

Do not store explosive

substances such as aerosol

cans with a flammable

propellant in this appliance.

This appliance is intended to be used

in household and similar applications

such as

– staff kitchen areas in shops, offices

and other working environments;

– farm houses and by clients in

hotels, motels and other residential

type environments;

– bed and breakfast type

environments;

– catering and similar non-retail

applications.

General Safety

• This product should not be

used by persons with physical,

sensory and mental disabilities,

without sufficient knowledge and

experience or by children. The device

can only be used by such persons

under supervision and instruction of

a person responsible for their safety.

Children should not be allowed to

play with this device.

• In case of malfunction, unplug the

device.

• After unplugging, wait at least 5

minutes before plugging in again.

• Unplug the product when not in use.

• Do not touch the plug with wet

hands! Do not pull the cable to plug

off, always hold the plug.

• Do not plug in the refrigerator if the

socket is loose.

• Unplug the product during

installation, maintenance, cleaning

and repair.

• If the product will not be used for

a while, unplug the product and

remove any food inside.

• Do not use the product when the

compartment with circuit cards

located on the upper back part of

the product (electrical card box

cover) (1) is open.

EN

5

1

• Do not use steam or steamed

cleaning materials for cleaning

the refrigerator and melting the

ice inside. Steam may contact the

electrified areas and cause short

circuit or electric shock!

• Do not wash the product by spraying

or pouring water on it! Danger of

electric shock!

• In case of malfunction, do not use

the product, as it may cause electric

shock. Contact the authorized

service before doing anything.

• Plug the product into an earthed

socket. Earthing must be done by a

qualified electrician.

• If the product has LED type lighting,

contact the authorized service for

replacing or in case of any problem.

• Do not touch frozen food with wet

hands! It may adhere to your hands!

• Do not place liquids in bottles and

cans into the freezer compartment.

They may burst out!

• Place liquids in upright position after

tightly closing the lid.

• Do not spray flammable substances

near the product, as it may burn or

explode.

• Do not keep flammable materials

and products with flammable gas

(sprays, etc.) in the refrigerator.

• Do not place containers holding

liquids on top of the product.

Splashing water on an electrified

part may cause electric shock and

risk of fire.

• Exposing the product to rain,

snow, sunlight and wind will cause

electrical danger. When relocating

the product, do not pull by holding

the door handle. The handle may

come off.

• Take care to avoid trapping any part

of your hands or body in any of the

moving parts inside the product.

• Do not step or lean on the door,

drawers and similar parts of the

refrigerator. This will cause the

product to fall down and cause

damage to the parts.

• Take care not to trap the power

cable.

• When positioning the appliance,

ensure the supply cord is not

trapped or damaged.

• Do not locate multiple portable

socket-outlets or portable power

supplies at the rear of the appliance.

EN

6

• Children aged from 3 to 8 years

are allowed to load and unload

refrigerating appliances.

• To avoid contamination of food,

please respect the following

instructions:

• – Opening the door for long

periods can cause a significant

increase of the temperature in the

compartments of the appliance.

• – Clean regularly surfaces that

can come in contact with food and

accessible drainage systems.

• – Clean water tanks if they have not

been used for 48 h; flush the water

system connected to a water supply

if water has not been drawn for 5

days.

• – Store raw meat and fish in suitable

containers in the refrigerator, so that

it is not in contact with or drip onto

other food.

• – Two-star frozen-food

compartments are suitable for

storing pre-frozen food, storing or

making icecream and making ice

cubes.

• – One-, two- and three-star

compartments are not suitable for

the freezing of fresh food.

• – If the refrigerating appliance is

left empty for long periods, switch

off, defrost, clean, dry, and leave

the door open to prevent mould

developing within the appliance.

1.1.1 HC Warning

If the product comprises a cooling

system using R600a gas, take care to

avoid damaging the cooling system

and its pipe while using and moving

the product. This gas is flammable. If

the cooling system is damaged, keep

the product away from sources of fire

and ventilate the room immediately.

C

The label on the inner left

side indicates the type of

gas used in the product.

1.1.2 For Models with

Water Dispenser

• Pressure for cold water inlet shall

be maximum 90 psi (6.2 bar). If

your water pressure exceeds 80

psi (5.5 bar), use a pressure limiting

valve in your mains system. If you

do not know how to check your

water pressure, ask for the help of a

professional plumber.

• If there is risk of water hammer

effect in your installation, always

use a water hammer prevention

equipment in your installation.

Consult Professional plumbers if you

are not sure that there is no water

hammer effect in your installation.

• Do not install on the hot water inlet.

Take precautions against of the

risk of freezing of the hoses. Water

temperature operating interval shall

be 33°F (0.6°C) minimum and 100°F

(38°C) maximum.

• Use drinking water only.

Intended Use

• This product is designed for home

use. It is not intended for commercial

use.

• The product should be used to store

food and beverages only.

• Do not keep sensitive products

requiring controlled temperatures

(vaccines, heat sensitive medication,

medical supplies, etc.) in the

refrigerator.

EN

7

• The manufacturer assumes no

responsibility for any damage due to

misuse or mishandling.

• Original spare parts will be provided

for 10 years, following the product

purchasing date.

Child Safety

• Keep packaging materials out of

children’s reach.

• Do not allow the children to play

with the product.

• If the product’s door comprises a

lock, keep the key out of children’s

reach.

Compliance with WEEE

Directive and Disposing of

the Waste Product

This product complies with

EU WEEE Directive (2012/19/EU). This

product bears a classification symbol

for waste electrical and electronic

equipment (WEEE).

This product has been

manufactured with high

quality parts and materials

which can be reused and

are suitable for recycling.

Do not dispose of the

waste product with

normal domestic and other wastes at

the end of its service life. Take it to the

collection center for the recycling of

electrical and electronic equipment.

Please consult your local authorities

to learn about these collection

centers.

Compliance with RoHS

Directive

• This product complies with EU WEEE

Directive (2011/65/EU). It does

not contain harmful and prohibited

materials specified in the Directive.

Package Information

Packaging materials of the product

are manufactured from recyclable

materials in accordance with our

National Environment Regulations. Do

not dispose of the packaging materials

together with the domestic or other

wastes. Take them to the packaging

material collection points designated

by the local authorities.

EN

8

3 Installation

B In case the information which are

given in the user manual are not

taken into account, manufacturer

will not assume any liability for this.

Points to be paid attention

to when the relocation of

the refrigerator

1. Your refrigerator should be

unplugged.Before transportation of

your refrigerator, it should be emptied

and cleaned.

2. Before it is re-packaged,

shelves, accessories, crisper, etc.

inside your refrigerator should be

fixed with adhesive tape and secured

against impacts. Package should be

bound with a thick tape or sound

ropes and the transportation rules

on the package should be strictly

observed.

3. Original packaging and foam

materials should be kept for future

transportations or moving.

Before you start the refrigerator,

Check the following before you

start to use your refrigerator:

1. Attach 2 plastic wedges as

illustrated below. Plastic wedges

are intended to keep the distance

which will ensure the air circulation

between your refrigerator and the

wall. (The picture is drawn up as a

representation and it is not identical

with your product.)

2. Clean the interior of the

refrigerator as recommended in the

“Maintenance and cleaning” section.

3. Connect the plug of the

refrigerator to the wall socket. When

the fridge door is opened, fridge

internal lamp will turn on.

4. When the compressor starts to

operate, a sound will be heard. The

liquid and gases sealed within the

refrigeration system may also give

rise to noise, even if the compressor

is not running and this is quite normal.

5. Front edges of the refrigerator

may feel warm. This is normal. These

areas are designed to be warm to

avoid condensation.

Electrical connection

Connect your product to a grounded

socket which is being protected by a

fuse with the appropriate capacity.

Important:

The connection must be in

compliance with national regulations.

• The power plug must be easily

accessible after installation.

• Electrical safety of your refrigerator

shall be guaranteed only if the earth

system in your house complies with

standards.

• The voltage stated on the label

located at left inner side of your

product should be equal to your

network voltage.

• Extension cables and multi plugs

must not be used for connection.

B A damaged power cable must be

replaced by a qualified electrician.

B Product must not be operated

before it is repaired! There is the risk

of electric shock!

EN

9

Disposing of the packaging

The packing materials may be

dangerous for children. Keep the

packing materials out of the reach

of children or dispose of them by

classifying them in accordance with

the waste instructions stated by your

local authorities. Do not throw away

with regular house waste, throw away

on packaging pick up spots designated

by the local authorities.

The packing of your refrigerator is

produced from recyclable materials.

Disposing of your old

refrigerator

Dispose of your old refrigerator

without giving any harm to the

environment.

• You may consult your authorized

dealer or waste collection center of

your municipality about the disposal

of your refrigerator.

Before disposing of your refrigerator,

cut out the electric plug and, if there

are any locks on the door, make them

inoperable in order to protect children

against any danger.

Placing and Installation

A If the entrance door of the

room where the refrigerator will be

installed is not wide enough for the

refrigerator to pass through, then call

the authorized service to have them

remove the doors of your refrigerator

and pass it sideways through the door.

1. Install your refrigerator to a

place that allows ease of use.

2. Keep your refrigerator away

from heat sources, humid places and

direct sunlight.

3. There must be appropriate air

ventilation around your refrigerator

in order to achieve an efficient

operation. If the refrigerator is to be

placed in a recess in the wall, there

must be at least 5 cm distance with

the ceiling and at least 5 cm with the

wall. Do not place your product on the

materials such as rug or carpet.

4. Place your refrigerator on an

even floor surface to prevent jolts.

EN

10

Placing the refrigerator

under the counter and

adjusting the legs

When you place your refrigerator, the

distance between the product and the

wall must be at least 30 mm, as seen

in the figure.

The air ventilation channels must not

be blocked so that the performance of

your refrigerator does not decrease.

(140 cm2)

If your refrigerator is unstable;

You may turn the front legs of your

refrigerator as seen in the figure to

balance it. The corner of the leg lowers

when the leg is turned in the direction

of the black arrow; it rises when the

leg is turned in the opposite direction.

It will be easier for you when you get

some help from someone to lift the

unit a little during this process.

3

4 4

3

EN

11

4 Preparation

• Your refrigerator should be installed

at least 30 cm away from heat

sources such as hobs, ovens, central

heater and stoves and at least 5

cm away from electrical ovens and

should not be located under direct

sunlight.

• The ambient temperature of

the room where you install your

refrigerator should at least be

10°C. Operating your refrigerator

under cooler conditions is not

recommended with regard to its

efficiency.

• Please make sure that the interior

of your refrigerator is cleaned

thoroughly.

• If two refrigerators are to be

installed side by side, there should

be at least 2 cm distance between

them.

• When you operate your refrigerator

for the first time, please observe the

following instructions during the

initial six hours.

• The door should not be opened

frequently.

• It must be operated empty without

any food in it.

• Do not unplug your refrigerator. If

a power failure occurs out of your

control, please see the warnings in

the “Recommended solutions for

the problems” section.

• Original packaging and foam

materials should be kept for future

transportations or moving.

• The baskets/drawers that are

provided with the chill compartment

must always be in use for low energy

consumption and for better storage

conditions.

• Food contact with the temperature

sensor in the freezer compartment

may increase energy consumption

of the appliance. Thus any contact

with the sensor(s) must be avoided.

• In some models, the instrument

panel automatically turns off 5

minutes after the door has closed.

It will be reactivated when the door

has opened or pressed on any key.

• Due to temperature change as

a result of opening/closing the

product door during operation,

condensation on the door/body

shelves and the glass containers is

normal

EN

12

5 Using your refrigerator

Temperature setting

button

The interior temperature of your

refrigerator changes for the following

reasons;

• Seasonal temperatures,

• Frequent opening of the door and

leaving the door open for long

periods,

• Foods put into the refrigerator

without decreasing the temperature

to room temperature.

• The location of the refrigerator in

the room (eg. exposing to sunlight)

You may adjust the varying interior

temperature using the thermostate.

If the ambient temperature is higher

than 32°C, switch the thermostate

button to maximum position.

Defrost

It is normal when ice particles form

on the back wall during the operation.

These do not need to be scratched

or wiped out. Your refrigerator

makes automatical defrost. Water

formed after defrost flows into the

evaporation container via the drain

pipe through the water collecting

chute, and here it evaporates

automatically.

•Check periodically whether the

evaporation pipe is clogged and

unclog it using the stick in the hole if

necessary.

EN

13

Changing the illumination

lamp

To change the Bulb/LED used for

illumination of your refrigerator, call

your AuthorisedService.

The lamp(s) used in this appliance

is not suitable for household room

illumination. The intended purpose

of this lamp is to assist the user to

place foodstuffs in the refrigerator/

freezer in a safe and comfortable

way.The lamps used in this appliance

have to withstand extreme physical

conditions such as temperatures

below -20 °C.

(only chest and upright freezer)

EN

14

6 Maintenance and cleaning

A Never use gasoline, benzene or

similar substances for cleaning

purposes.

B We recommend that you unplug the

appliance before cleaning.

B Never use any sharp abrasive

instrument, soap, household

cleaner, detergent and wax polish

for cleaning.

B For non-No Frost products,

water drops and frosting up to a

fingerbreadth occur on the rear wall

of the Fridge compartment. Do not

clean it; never apply oil or similar

agents on it.

B Only use slightly damp microfiber

cloths to clean the outer surface

of the product. Sponges and other

types of cleaning cloths may scratch

the surface.

C Use lukewarm water to clean the

cabinet of your refrigerator and wipe

it dry.

C Use a damp cloth wrung out in

a solution of one teaspoon of

bicarbonate of soda to one pint of

water to clean the interior and wipe

it dry.

B Make sure that no water enters the

lamp housing and other electrical

items.

B If your refrigerator is not going to

be used for a long period of time,

unplug the power cable, remove all

food, clean it and leave the door ajar.

C Check door seals regularly to ensure

they are clean and free from food

particles.

A To remove door racks, remove all the

contents and then simply push the

door rack upwards from the base.

A Never use cleaning agents or water

that contain chlorine to clean the

outer surfaces and chromium coated

parts of the product. Chlorine causes

corrosion on such metal surfaces.

A Do not use sharp, abrasive tools,

soap, household cleaning agents,

detergents, kerosene, fuel oil,

varnish etc. to prevent removal and

deformation of the prints on the

plastic part. Use lukewarm water

and a soft cloth for cleaning and

then wipe it dry.

Protection of plastic

surfaces

C Do not put the liquid oils or oil-

cooked meals in your refrigerator

in unsealed containers as they

damage the plastic surfaces of your

refrigerator. In case of spilling or

smearing oil on the plastic surfaces,

clean and rinse the relevant part

of the surface at once with warm

water.

EN

15

7 Troubleshooting

Check this list before contacting the

service. Doing so will save you time

and money. This list includes frequent

complaints that are not related to

faulty workmanship or materials.

Certain features mentioned herein

may not apply to your product.

The refrigerator is not working.

• The power plug is not fully

settled. >>> Plug it in to settle

completely into the socket.

• The fuse connected to the

socket powering the product or

the main fuse is blown. >>> Check

the fuses.

Condensation on the side wall of

the cooler compartment (MULTI

ZONE, COOL, CONTROL and FLEXI

ZONE).

• The door is opened too

frequently >>> Take care not

to open the product’s door too

frequently.

• The environment is too humid.

>>> Do not install the product in

humid environments.

• Foods containing liquids are

kept in unsealed holders. >>>

Keep the foods containing liquids

in sealed holders.

• The product’s door is left open.

>>> Do not keep the product’s

door open for long periods.

• The thermostat is set to

too low temperature. >>> Set

the thermostat to appropriate

temperature.

Compressor is not working.

• In case of sudden power failure

or pulling the power plug off and

putting back on, the gas pressure

in the product’s cooling system is

not balanced, which triggers the

compressor thermic safeguard.

The product will restart after

approximately 6 minutes. If the

product does not restart after this

period, contact the service.

• Defrosting is active. >>> This

is normal for a fully-automatic

defrosting product. The defrosting

is carried out periodically.

• The product is not plugged in.

>>> Make sure the power cord is

plugged in.

• The temperature setting

is incorrect. >>> Select the

appropriate temperature setting.

• The power is out. >>> The

product will continue to operate

normally once the power is

restored.

The refrigerator’s operating noise

is increasing while in use.

• The product’s operating

performance may vary depending

on the ambient temperature

variations. This is normal and not a

malfunction.

The refrigerator runs too often or

for too long.

• The new product may be larger

than the previous one. Larger

products will run for longer

periods.

• The room temperature may

be high. >>> The product will

normally run for long periods in

higher room temperature.

• The product may have

been recently plugged in or a new

food item is placed inside. >>> The

EN

16

product will take longer to reach

the set temperature when recently

plugged in or a new food item is

placed inside. This is normal.

• Large quantities of hot food

may have been recently placed into

the product. >>> Do not place hot

food into the product.

• The doors were opened

frequently or kept open for long

periods. >>> The warm air moving

inside will cause the product to run

longer. Do not open the doors too

frequently.

• The freezer or cooler door

may be ajar. >>> Check that the

doors are fully closed.

• The product may be set to

temperature too low. >>> Set the

temperature to a higher degree and

wait for the product to reach the

adjusted temperature.

• The cooler or freezer door

washer may be dirty, worn out,

broken or not properly settled.

>>> Clean or replace the washer.

Damaged / torn door washer will

cause the product to run for longer

periods to preserve the current

temperature.

The freezer temperature is very

low, but the cooler temperature is

adequate.

• The freezer compartment

temperature is set to a very low

degree. >>> Set the freezer

compartment temperature to a

higher degree and check again.

The cooler temperature is very

low, but the freezer temperature

is adequate.

• The cooler compartment

temperature is set to a very low

degree. >>> Set the freezer

compartment temperature to a

higher degree and check again.

The food items kept in cooler

compartment drawers are frozen.

• The cooler compartment

temperature is set to a very low

degree. >>> Set the freezer

compartment temperature to a

higher degree and check again.

The temperature in the cooler or

the freezer is too high.

• The cooler compartment

temperature is set to a very high

degree. >>> Temperature setting

of the cooler compartment has

an effect on the temperature in

the freezer compartment. Wait

until the temperature of relevant

parts reach the sufficient level

by changing the temperature of

cooler or freezer compartments.

• The doors were opened

frequently or kept open for long

periods. >>> Do not open the

doors too frequently.

• The door may be ajar. >>> Fully

close the door.

• The product may have been

recently plugged in or a new

food item is placed inside. >>>

This is normal. The product will

take longer to reach the set

temperature when recently

plugged in or a new food item is

placed inside.

• Large quantities of hot food

may have been recently placed into

the product. >>> Do not place hot

food into the product.

EN

17

Shaking or noise.

• The ground is not level or

durable. >>> If the product is

shaking when moved slowly,

adjust the stands to balance

the product. Also make sure the

ground is sufficiently durable to

bear the product.

• Any items placed on the

product may cause noise. >>>

Remove any items placed on the

product.

The product is making noise of

liquid flowing, spraying etc.

• The product’s operating

principles involve liquid and gas

flows. >>> This is normal and not

a malfunction.

There is sound of wind blowing

coming from the product.

• The product uses a fan for the

cooling process. This is normal and

not a malfunction.

There is condensation on the

product’s internal walls.

• Hot or humid weather will

increase icing and condensation.

This is normal and not a

malfunction.

• The doors were opened

frequently or kept open for long

periods. >>> Do not open the

doors too frequently; if open, close

the door.

• The door may be ajar. >>> Fully

close the door.

There is condensation on the

product’s exterior or between the

doors.

• The ambient weather may

be humid, this is quite normal

in humid weather. >>> The

condensation will dissipate when

the humidity is reduced.

The interior smells bad.

• The product is not cleaned

regularly. >>> Clean the interior

regularly using sponge, warm

water and carbonated water.

• Certain holders and packaging

materials may cause odour.

>>> Use holders and packaging

materials without free of odour.

• The foods were placed in

unsealed holders. >>> Keep the

foods in sealed holders. Micro-

organisms may spread out of

unsealed food items and cause

malodour. Remove any expired or

spoilt foods from the product.

The door is not closing.

• Food packages may be blocking

the door. >>> Relocate any items

blocking the doors.

• The product is not standing in

full upright position on the ground.

>>> Adjust the stands to balance

the product.

• The ground is not level or

durable. >>> Make sure the

ground is level and sufficiently

durable to bear the product.

The vegetable bin is jammed.

• The food items may be in

contact with the upper section of

the drawer. >>> Reorganize the

food items in the drawer.

If The Surface Of The Product Is

Hot.

• High temperatures may be

observed between the two doors,

on the side panels and at the rear

grill while the product is operating.

This is normal and does not require

service maintenance!Be careful

when touching these areas.

A WARNING:

If the problem persists after following

the instructions in this section, contact

your vendor or an Authorised Service.

Do not try to repair the product.

EN

18

DISCLAIMER / WARNING

Some (simple) failures can be adequately

handled by the end-user without any

safety issue or unsafe use arising,

provided that they are carried out within

the limits and in accordance with the

following instructions (see the “Self-

Repair” section).

Therefore, unless otherwise authorized

in the “Self-Repair” section below,

repairs shall be addressed to registered

professional repairers in order to avoid

safety issues. A registered professional

repairer is a professional repairer that has

been granted access to the instructions

and spare parts list of this product by the

manufacturer according to the methods

described in legislative acts pursuant to

Directive 2009/125/EC.

However, only the service agent (i.e.

authorized professional repairers)

that you can reach through the phone

number given in the user manual/

warranty card or through your

authorized dealer may provide service

under the guarantee terms. Therefore,

please be advised that repairs by

professional repairers (who are not

authorized by Beko) shall void the

guarantee.

Self-Repair

Self-repair can be done by the end-user

with regard to the following spare parts:

door handles,door hinges, trays, baskets

and door gaskets (an updated list is also

available in support.beko.com as of 1st

March 2021).

Moreover, to ensure product safety and to

prevent risk of serious injury, the mentioned

self-repair shall be done following the

instructions in the user manual for self-

repair or which are available in support.

beko.com. For your safety, unplug the

product before attempting any self-repair.

Repair and repair attempts by end-users

for parts not included in such list and/

or not following the instructions in the

user manuals for self-repair or which are

available in support.beko.com, might give

raise to safety issues not attributable to

Beko, and will void the warranty of the

product.

Therefore, it is highly recommended that

end-users refrain from the attempt to carry

out repairs falling outside the mentioned

list of spare parts, contacting in such

cases authorized professional repairers

or registered professional repairers. On

the contrary, such attempts by end-users

may cause safety issues and damage

the product and subsequently cause fire,

flood, electrocution and serious personal

injury to occur.

By way of example, but not limited to,

the following repairs must be addressed

to authorized professional repairers

or registered professional repairers:

compressor, cooling circuit, main

board,inverter board, display board, etc.

The manufacturer/seller cannot be held

liable in any case where end-users do not

comply with the above.

The spare part availability of the refrigerator

that you purchased is 10 years.

During this period, original spare parts will

be available to operate the refrigerator

properly

EN

19

The minimum duration of guarantee of

the refrigerator that you purchased is 24

months.

This product is equipped with a lighting

source of the "G" energy class.

The lighting source in this product

shall only be replaced by professional

repairers.

Packaging sorting information

Please scan the QR code which

places on the outer packaging of the

product to find all the information

relating to the packaging and how to

manage the packaging waste.

Leht laadib ...

Beko BU 1100 HCA Kasutusjuhend

Beko BU 1100 HCA Kasutusjuhend

teistes keeltes

Muud dokumendid