Not for
Reproduction
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80014966 Rev C
020632-00
BPW3000PX
Copyright © 2018. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
en - English
ar -
da - Dansk
es - Español
fi - Suomi
fr - Français
hu - Magyar
nl - Nederlands
no - Norsk
pl - Polski
ru -
sv - Svenska
sw - Kiswahili
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
A
C
B
D
12
10
7
80010441
6
C
A
B
C
1
B
A
2
B
A
3
C
B
A
4
8
A
B
A
9
0˚ 15˚40˚
11
A
B C D
E
F G
Not for
Reproduction
3
A
C
N
M
S
R
P
D
B
H
G
E
5
F
K
J
L
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Safety and Control Symbols ....................... 4
Equipment Description............................ 5
Assembly....................................... 5
Features and Controls ............................ 5
Operation....................................... 5
Maintenance .................................... 8
Storage ........................................ 9
Troubleshooting ................................10
Specifications ..................................10
Warranty ......................................11
The safety alert symbol indicates a potential personal injury
hazard. A safety symbol may be used to represent the
type of hazard. WARNING indicates a hazard which, if not
avoided, could result in death or serious injury. CAUTION
indicates a hazard which, if not avoided, could result in
minor or moderate injury. NOTICE indicates information
considered important, but not hazard-related.
Never spray yourself, others, animals, power
sources, or the unit itself.
This machine is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless supervised
and given instruction concerning safe operation
and understanding of hazards involved.
WARNING!
• This machine has been designed for use with
the cleaning agent supplied or recommended
by the manufacturer. The use of other cleaning
agents or chemicals may adversely affect the
safety of the machine.
• High pressure jets can be dangerous if subject to
misuse. The jet must not be directed at persons,
live electrical equipment or the machine itself.
• Do not use the machine within range of persons
unless they wear protective clothing.
• Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
• Risk of explosion – Do not spray flammable liquids.
• High pressure cleaners shall not be used by
children or untrained personnel.
• High pressure hoses, fittings and couplings
are important for the safety of the machine.
Use only hoses, fittings and couplings
recommended by the manufacturer.
• To ensure machine safety, use only original
spare parts from the manufacturer or approved
by the manufacturer
• Water that has flown through backflow
preventers is considered to be non-potable.
• Do not use the machine if important parts of the
machine are damaged, e.g. safety devices, high
pressure hoses, trigger gun.
• Where no ignition key and no battery exist, the
disconnection can be acheived by equivalent means.
• Do not use combustion engine powered
machines indoors unless adequate ventilation is
assessed by national labour authorities.
• Ensure that any exhaust emissions are not in
the vicinity of air intakes.
• Incorrect fuels shall not be used as they may
prove hazardous.
• Throttle control lever shall be in STOP (
)
position during cleaning or maintenance and
when replacing parts.
Warning Tag Figure
6
A warning tag is provided on your unit to inform you of
potential safety hazards. If the tag becomes damaged
or illegible, replace it by contacting your local Briggs &
Stratton dealer to obtain a new one.
For questions regarding European emissions, please
contact our European office at:
Fire
Explosion
Toxic Fumes
Moving Parts
Fall
Kickback
Flying Objects
Fluid Injection
Instruction
Manual
Chemical Burn
Projectile
Electrical Shock
Safety Alert
Symbol
Check Oil
Level
Do Not Start
Engine
!
Hot Surface
OFF
ON
Non-Potable
Water
Not for
Reproduction
5
NOTICE If you have questions about intended use, ask
dealer or contact qualified service center. NEVER operate
units with broken or missing parts, or without protective
housing or covers. DO NOT by-pass any safety device
on this machine. DO NOT modify pressure washer in any
way. This equipment is designed to be used with Briggs &
Stratton authorized parts ONLY.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
POWERflow+ Technology™
The force behind POWERflow+ is in the pump with two
separate cleaning modes: high pressure and high flow. High-
pressure mode delivers up to 20.7 MPa (3000 PSI or 207
BAR) and is ideal for cleaning the toughest stains, mildew and
grime from decks, driveways and siding, while high-flow mode
delivers up to 18.9 LPM (liters per minute) (5 GPM (gallons per
minute)) to power-rinse away dirt, soap and debris.
Briggs & Stratton’s POWERflow+ Technology is a system
of components working together to deliver the high-flow
capability. Water is sent from the pump to the specially
designed 9.1 m (30 ft.) hose and into the POWERflow+ gun
with soft grip handle. Water then flows into the 7-in-1 nozzle
that allows user to change from High Pressure to High Flow,
and propels the stream up to 9.1 m (30 ft.).
When transporting equipment with a vehicle or trailer,
EMPTY fuel tank or turn fuel shutoff valve, if equipped, to
OFF (0) position. DO NOT tip engine or equipment at angle
which causes fuel to spill.
Assembly
Figure
1
2
3
4
1. Place handle (1, A) onto supports (1, B) and align
holes (1, C).
2. Insert carriage bolts (2, A) through holes from inside
of unit, attach with plastic knob (2, B) and tighten.
NOTICE Handle can fold forward by loosening knobs
to unthreaded section of bolt. DO NOT fold handle while
engine is hot.
3. Insert rubber strap (3,A) through slot (3,B) in back of
accessory tray and pull tight from front.
4. Place accessory tray (4, A) over holes (4, B) on
handle and push tree clips (4, C) into holes.
5
Oil
Figure
7
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
5
8
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Clean area around oil fill (5,F) and remove oil fill cap/
dipstick.
3. Verify oil is at Full mark (top hole) (8,A) on dipstick.
4. If needed, slowly pour oil into oil fill opening to Full
mark (top hole) on dipstick. DO NOT overfill.
5. Replace and tighten oil fill cap/dipstick.
NOTICE DO NOT attempt to crank or start engine before
before it has been properly serviced with recommended oil.
This could result in an engine failure.
CAUTION! Avoid prolonged or repeated skin contact
with used motor oil. Used motor oil has been shown to
cause skin cancer in certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON’T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel Figure
9
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For high
altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
A 7-in-1 Nozzle J Pump
B Accessory Tray K Detergent Tank
C Spray Gun L Identification Label
D Warning Tag M Air Filter
E Recoil Starter N Engine Rocker Switch
F Oil Fill/Dipstick P Fuel Tank
G High Pressure Outlet R Nozzle Extension with
Quick Connect
H Water Supply Inlet S High Pressure Hose
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty. DO NOT use
unapproved gasoline such as E15 and E85. DO NOT mix
oil in gasoline or modify engine to run on alternate fuels.
To protect the fuel system from gum formation, mix in a fuel
stabilizer when adding fuel. See Storage. All fuel is not the
same. If you experience starting or performance problems
after using fuel, switch to a different fuel provider or change
brands. This engine is certified to operate on gasoline.
WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury. Turn pressure washer
engine off and let it cool at least 2 minutes before removing
fuel cap. Loosen cap slowly to relieve pressure in tank. Fill
fuel tank outdoors. DO NOT overfill tank. Allow space for
fuel expansion. If fuel spills, wait until it evaporates before
starting engine. Keep fuel away from sparks, open flames,
pilot lights, heat, and other ignition sources. Check fuel
lines, tank, cap and fittings frequently for cracks or leaks.
Replace if necessary. DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B).
Be careful not to overfill. DO NOT fill above bottom of
fuel tank neck to allow for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
At altitudes over 1,524 m (5,000 ft.), a minimum 85 octane /
85 AKI (89 RON) gasoline is acceptable. To remain emissions
compliant, high altitude adjustment is required. Operation
without this adjustment will cause decreased performance,
increased fuel consumption, and increased emissions. See an
Authorized Briggs & Stratton dealer for high altitude adjustment
information. Operation of the engine at altitudes below 762 m
(2,500 ft.) with the high altitude kit is not recommended.
10
Carbon Monoxide Poisoning
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or taste it. Even if
you do not smell exhaust fumes, you could still be exposed to
carbon monoxide gas. Operate this product ONLY outside far
away from windows, doors and vents to reduce the risk of
carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces. Install battery-operated carbon
monoxide alarms or plug-in carbon monoxide alarms with battery
back-up according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas. DO NOT run this
product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or
opening doors and windows for ventilation. Carbon monoxide
can quickly build up in these spaces and can linger for hours,
even after this product has shut off. ALWAYS place this product
downwind and point the engine exhaust away from occupied
spaces. If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You may
have carbon monoxide poisoning.
Risk of Fire Clearances
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
Keep at least 1.5 m (5 ft.) clearance on all sides of
pressure washer including overhead.
Figure
5
NOTICE Inspect high pressure hose for cuts, leaks or damage.
1. Pull back on collar of high pressure hose (S), slide onto
spray gun (C) and release collar. Tug on hose to make
sure it is secure.
2. Attach other end of hose to outlet (G) on pump and tighten.
3. Inspect inlet screen before connecting garden hose to
water inlet (H). Clean screen if it contains debris or
replace if damaged. DO NOT run pressure washer if
inlet screen is damaged.
4. Make sure water source is capable of supplying water
at a flow rate greater than 26.5 liters (7.0 gallons) per
minute and 0.17-0.55 MPa (25-80 PSI or 1.7-5.5 BAR)
at pressure washer end of garden hose.
5. Run water through garden hose to clean out debris.
NOTICE Use ONLY cold water (less than 38°C (100°F)).
NOTICE Using a backflow preventer at pump inlet could
cause pump damage. There MUST be at least 3 m (10 ft.)
of unrestricted garden hose between pressure washer inlet
and backflow preventer.
WARNING! Water that has flowed through a
backflow preventer is considered to be non-potable.
6. Connect garden hose (not to exceed 15 m (50 ft.)) to
water inlet and tighten.
7. Turn ON water, press red button on gun, and squeeze
trigger to purge system of air. Replace gun if trigger
does not lock.
8. Attach nozzle extension (R) to gun (C) and tighten.
9. Pull back on collar of nozzle extension, insert 7-in-1 nozzle
(A) and release. Tug on nozzle to make sure it is secure.
5
NOTICE DO NOT run pump without water supply
connected and turned on.
1. Push engine switch (N) to ON (I) position.
WARNING! Starter and other rotating parts could
entangle hands, hair, clothing, or accessories resulting
in serious injury. NEVER operate pressure washer
without protective housing or covers. DO NOT wear loose
clothing, jewelry or anything that could be caught in the starter
or other rotating parts. Tie up long hair and remove jewelry.
WARNING! Spray could splash back or
propel objects resulting in serious injury.
Always wear indirect vented (chemical splash)
safety goggles marked to comply with EN166 when using or in
vicinity of this equipment. Always wear protective clothing such
as a long-sleeved shirt, long pants and close-toed shoes.
NOTICE Unit is equipped with a ReadyStart® engine
meaning no priming or choking required.
2. When starting engine, grasp recoil handle and pull
slowly until you feel some resistance. Then pull rapidly
to start engine.
Not for
Reproduction
7
WARNING! Starter cord kickback (rapid
retraction) will pull hand and arm toward engine
faster than you can let go which could cause
broken bones, fractures, bruises, or sprains resulting in
serious injury. NEVER pull starter cord without first
relieving spray gun pressure. When starting engine, pull
cord slowly until resistance is felt and then pull rapidly to
avoid kickback. Firmly grasp spray gun with both hands
when using high pressure spray to avoid injury when spray
gun kicks back.
3. Return recoil handle slowly. DO NOT let rope “snap
back” against starter.
WARNING! The high pressure stream of water
that this equipment produces could cut through
skin and its underlying tissues, resulting in serious
injury and possible amputation. If cut by fluid, call physician
immediately. DO NOT treat as a simple cut. DO NOT allow
CHILDREN to operate pressure washer. NEVER aim spray
gun at people, animals, or plants. DO NOT secure spray
gun in open position. DO NOT leave spray gun unattended
while machine is running. NEVER use a spray gun which
does not have a trigger lock or trigger guard in place and in
working order. NEVER connect high pressure hose to
nozzle extension.
WARNING! Contact with muffler area could
cause burns resulting in serious injury. DO NOT
touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
WARNING! Contact with power source could
cause electric shock or burn resulting in death or
serious injury. NEVER spray near power source.
11
7-in-1 nozzle allows you to switch between seven different
spray pattern nozzles once spray gun trigger is locked.
1. Select desired spray pattern:
•
Select Maximum 0° (A) nozzle setting for stubborn or
hard to reach surface such as second story surfaces,
paint removal, oil stains, rust removal or other
stubborn substances (tar, gum, grease, wax, etc.).
• Select General 15° (B) nozzle setting for tougher
cleaning tasks. Ideal for removing grease and dirt
from hard surfaces. Also capable of stripping paint
when held at a 45° angle.
• Select Gentle 40° (C) nozzle setting for gentle
cleaning of cars/trucks, boats, RV’s, patio furniture,
lawn equipment, etc.
• Select Fan Spray (D) nozzle setting for optimal
high flow rinsing away of light dirt and debris.
• Select Fan Spray with Soap (E) nozzle setting for
delicate surface cleaning of cars, trucks, childrens
play equipment, patio furniture, etc.
• Select Extended Reach (F) nozzle setting for quick
high flow clean up and long reach cleaning of
second story siding and windows.
• Select Extended Reach with Soap (G) nozzle setting
to propell soap to second story siding and windows.
2. Turn dial until desired spray pattern lines up with arrow
on 7-in-1 nozzle.
Usage Tips
• In High Pressure Mode, keep 7-in-1 nozzle 20 to 61 cm
(8 to 24 in.) away from cleaning surface.
• If you get the 7-in-1 nozzle too close, you may
damage surface being cleaned.
• DO NOT get closer than 15 cm (6 in.) when cleaning
tires.
WARNING! Chemicals could cause burns
resulting in death or serious injury. DO NOT use
caustic liquid with pressure washer. Use ONLY
pressure washer safe detergents/soaps. Follow
manufacturers instructions.
1. Remove cap from detergent tank, fill with appropriate
detergent and replace cap.
2. Select a soap nozzle setting.
NOTICE Detergent cannot be applied with non soap
nozzle setting (maximum, general, gentle, fan spray or
extended reach).
3. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
4. Allow detergent to “soak in” per detergent
manufacturer’s instructions.
Pressure Washer Rinsing
1. Select a non soap nozzle setting.
WARNING! Kickback from spray gun (29 N) could
cause you to fall resulting in death or serious injury.
Operate pressure washer from a stable surface. Be
extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location. Firmly
grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
2. Apply a high pressure spray to a small area and check
surface for damage. If no damage is found, continue rinsing.
3. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Circulating water in pump can reach temperatures above
51°C (125°F) if running pressure washer for 3-5 minutes
without pressing trigger on gun. The system engages to
cool pump by
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
1. Release spray gun trigger and let engine idle for two minutes.
2. Push engine switch to OFF (0) position.
3. ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING!
Spray gun traps high water pressure,
even when engine is stopped and water is
disconnected, which could result in serious injury.
Keep high pressure hose connected to pump and spray gun
while system is pressurized. ALWAYS point spray gun in
safe direction, press red button and squeeze spray gun
trigger to release high pressure, every time you stop engine.
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and freeze
pump action. Follow these procedures after every use:
1. Turn off water supply, and let engine cool.
2. Disconnect hose from gun and outlet on pump. Drain
water from hose, gun, and nozzle extension.
3. Place gun, nozzle extension, nozzle and hose on
accessory tray.
4. Empty pump of all liquids by pulling recoil handle
about six times.
5. Store unit in a clean, dry area.
NOTICE If storing for more than 30 days, see Storage.
WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion resulting
in death or serious injury. When storing fuel or equipment with
fuel in tank, store away from furnaces, stoves, water heaters,
clothes dryers, or other appliances that have pilot light or
other ignition source because they could ignite fuel vapors.
Follow hourly or calendar intervals, whichever occurs first. More
frequent service is required when operating in adverse conditions.
1
Service more often under dirty or dusty conditions.
Regular maintenance will improve performance and extend
the life of the pressure washer. See any Briggs & Stratton
Authorized Service Dealer for service. DO NOT allow
children to clean or maintain without supervision.
NOTICE Your pressure washer was designed and
intended to be used with POWERflow+ components ONLY.
Using components that are not designed for POWERflow+
will cause your pressure washer to not function optimally.
WARNING! To ensure machine safety, use only
original spare parts from the manufacturer or approved by
the manufacturer. Should you have questions about
replacing components on your pressure washer, please
visit our website at BRIGGSandSTRATTON.COM.
• Change engine oil
Every 8 Hours or Daily
• Clean debris
• Check engine oil level
Every 50 Hours or Yearly
• Clean engine air cleaner
1
• Change engine oil
1
• Inspect muffler
Every 200 Hours or Yearly
• Replace engine air cleaner
1
Yearly
• Replace spark plug
• Clean cooling system
1
Not for
Reproduction
9
Occasionally check ball in detergent siphoning system may
become stuck from storage, dried soap, or minerals in water.
The check ball can be freed by performing the following:
1. Turn off water supply.
2. With engine off and pressure released from system,
remove detergent hose from barbed fitting on pump.
3. Using a firm, blunt object 2mm (7/64”) in diameter or
smaller, by at least 25.4mm (1”) long, such as an Allen
wrench, slowly insert object into barbed fitting until you
meet resistance. This resistance is the check ball.
4. Slowly push down until you feel ball move slightly,
push no more than 3mm (1/8”). Slight pressure may
be required to free ball.
5. Repeat steps 3 and 4 if necessary.
6. Reinstall detergent hose onto barb fitting.
7. Treat with PumpSaver as described in Protecting the
Pump during storage to prevent reoccurrence.
5
Clean nozzles to correct excessive pump pressure caused
by a clogged nozzle:
1. Turn off water supply.
2. Remove 7-in1 nozzle (A) from nozzle extension.
3. Use a small paper clip to free any foreign material
clogging or restricting any of the nozzles.
4. Reinstall 7-in-1 nozzle into nozzle extension.
12
The use of a lubricant (petroleum or synthetic grease) helps
seat o-rings providing an improved seal. Apply lubricant to
o-rings prior to assembling garden hose on pump (A), high
pressure hose (B), spray gun (C), and nozzle extension (D).
Purchase an O-Ring Maintenance Kit by contacting a
Briggs & Stratton Authorized Service Dealer. Refer to the
instruction sheet provided in the kit to service your unit’s
o-rings. NEVER repair leaking connections with sealant of
any kind. Replace o-ring or seal.
If you do not plan to use the pressure washer for more than
30 days, you must prepare engine and pump for storage.
1. Disconnect detergent hose on pump and place into
container.
2. Place container under drain on detergent tank and
unscrew cover from drain. Remove tanks cover, tip
pressure washer back slightly and empty tank.
3. Reconnect hose to pump and screw cap back on drain.
4. Add 0.5 liter (16.9 oz.) of clean, fresh water to tank
and close cover.
5. Flush tank until empty by running pressure washer
with a soap nozzle selected.
To protect pump from damage caused by mineral deposits
or freezing, use PumpSaver to prevent freeze damage and
lubricate pistons and seals.
NOTICE Failure to protect unit from freezing
temperatures will damage pump and render unit
inoperable. Freeze damage is not covered under warranty.
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system or
on essential carburetor parts.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine for 2 minutes to circulate the stabilizer throughout
the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to
maintain freshness.
1. DO NOT store fuel from one season to another unless it
has been treated as described in Protect Fuel System.
2. Cover unit with a suitable protective cover that does
not retain moisture.
WARNING! Storage covers could cause a fire
resulting in death or serious injury. DO NOT place
a storage cover over a hot pressure washer. Let
equipment cool for a sufficient time before placing the
cover on the equipment.
3. Store unit in a clean, dry area.
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Max Outlet Pressure .. 20.7 MPa* (3,000 PSI or 207 BAR) @ 8.7 LPM (2.3
Max Flow Rate .........2.76 MPa (400 PSI or 28 BAR) @ 18.9 LPM* (5.0 GPM)
Water Supply Temperature .............................. 38°C (100°F) MAX
Displacement .......................................190 cc (11.58 cu. in.)
Spark Plug Gap ...................................... 0.50 mm (0.020 in.)
Fuel Capacity .........................................1.13 Liters (1.2 Qt.)
Oil Capacity .......................................0.6 Liters (20 Ounces)
Sound Pressure @ 3 m ..........................................88 dBA
§
O-Ring Maintenance Kit..........................................705002
Water Inlet Screen ............................................B2384GS
Engine Oil Bottle ...............................................100005E
PumpSaver ......................................................6039
Problem Cause
volume.
1. Inadequate water supply.
2. Inlet hose is kinked or leaking.
3. Clogged inlet hose screen.
4. Water supply is over 38°C (100°F).
5. High pressure hose is blocked or
leaks.
6. Spray gun leaks.
7. Nozzle is obstructed.
1. Provide adequate water flow.
2. Straighten inlet hose, patch leak.
3.
Check and clean inlet hose screen.
4. Provide cooler water supply.
5. Clear blocks in outlet hose, replace
if leaking.
6. Replace spray gun.
7. Clean nozzles.
spray.
1. Detergent tube is clogged or cracked.
2. Check ball stuck in detergent system.
3. High pressure or high flow, without
soap, nozzle is selected.
1. Clean or replace detergent tube.
2. Unstick check ball as described in
Detergent Siphoning Check Ball.
3. Select a high flow soap nozzle
setting (indicated with bubbles).
and runs rough.
1. Engine switch in OFF (0) position.
2. Low oil level.
3. Out of fuel.
4. Spark plug wire not connected to
spark plug.
5. Flooded.
1. Set engine swith to ON (I) position.
2. Fill crankcase to proper level.
3. Fill fuel tank.
4. Connect wire to spark plug.
5. Wait 5 minutes and re-crank engine.
The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society
of Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with
SAE J1995. Torque values are derived at 2600 RPM for those engines with “rpm” called out on the label and
3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross power curves can be viewed at
www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air cleaner installed whereas gross
power values are collected without these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide array of
products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given
piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine
components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating
conditions (temperature, humidity, altitude), and engine-to engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard
PW101-2010 (Testing and Rating Performance of Pressure Washers).
§
Measured sound values in accordance to Tasmanian Environmental Management and Pollution Control (Miscellaneous
Noise) Regulations.
Not for
Reproduction
11
80010169_EN Rev C
BRIGGS & STRATTON WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is
effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator
map at BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized
Service Dealer for inspection and testing.
.
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related
components are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a
retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not
cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the
Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial
number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage
or water/chemical corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced
or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when
normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine
brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for
primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
Equipment 24 months 3 months
Engine* 24 months 3 months
Battery (if equipped) 3 months None
Not for
Reproduction
Briggs & Stratton
POWERflow+ Technology™
POWERflow+
(BAR 2073000) 20.7
( 5)18.9
Briggs & Stratton POWERflow+
POWERflow+ (
30) 9.1
1 7
.(
30) 9.1
.(0)
4
3
2
1
.(C 1) (B 1) (A 1) .1
(A2) .2
(B2)
(B3) (A3) .3
(B4) (A4) .4
(C4)
5
7
Briggs & Stratton
SJ SG SF
(40) 4° *
SAE 30
(80) 27 **
10W30
8
5
8
.1
(F5)
.2
(A8) () .3
.4
.5
9
•
AKI (91 RON) 87/87 •
.() 10% •
.E85 E15
(2)
A1 7 J
B
K
C
L
D
M
E
N
F
P
G
R
H
S
5 BRIGGSandSTRATTON.COM
Not for
Reproduction
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
•
6
Briggs & Stratton
!
4
Not for
Reproduction
11
1 7 -
1 7
.1
(A) 0
•
(B) 15 •
45
(C) 40 •
(D) •
(E) •
(F)
•
(G)
•
.1 7 .2
61 201 7 •
( 24 8)
1 7
•
(
6)
15
•
.1
.2
.3
.4
.1
(N 29)
.2
.3
51
3-5 (125)
.1
.(0) .2
.3
.1
.2
.3
.4
.5
30
7 BRIGGSandSTRATTON.COM
Not for
Reproduction
.1
.(B) (A) .2
.3
( 5000)
1524
AKI (89 RON) 85/85
Briggs
& Stratton
( 2500)
762
10
( 5) 1.5
5
,(S) .1
(C)
(G)
.2
.(H) .3
.4
0.17-0.55 ( 7.0) 26.5
(BAR 1.7-5.5 25-80)
.5
.(( 100) 38° )
(10) 3
(
50)
15 ) .6
.7
(C) (R)
.8
(A) 1 7 .9
5
.(I) (N) .1
EN166
ReadyStart®
.2
.3
6
Not for
Reproduction
.1
.2
.3
38 .4
( 100)
.5
.6
.7
.1
.2
.3
.4
.5
.
.6
.7
.1
.2
.3
.1
.2
.
.3
()
(0) .1
.2
.3
.4
.5
(I) .1
.2
. 3
.4
5 .5
.
J1940 (SAE)
2600 .J1995
3600 3060
.www.BRIGGSandSTRATTON.COM
()
Briggs & Stratton
()
() 2010 PW101 (PWMA)
*
.()
§
2.3) 8.7 @ ( 3000) *20.7. . . . . . . . . . .
( 5.0) * 18.9 @ ( 400) 2.76 . . . . . . .
( 100) 38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(. 11.58) 190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
( 0.020) 0.50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
( 1.2) 1.13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
( 20) 0.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
§
88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
705002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B2384GS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100005E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6039 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 BRIGGSandSTRATTON.COM
Not for
Reproduction
1
Briggs & Stratton
POWERflow+
POWERflow+
.BRIGGSandSTRATTON.COM
.1
.2
( 7/64) 2 .3
( 1) 25.4
.4
.( 1/8) 3
4 3 .5
.6
.7
5
.1
(A) 1 7 .2
.3
1 7 .4
12
,(CBA
.(D
Briggs & Stratton
30
.1
.2
.3
( 16.9) 0.5 .4
.5
ةظحم
30
.1
.2
.3
5
•
8
•
•
50
1
•
1
•
•
200
1
•
•
1
•
8
Not for
Reproduction
11 BRIGGSandSTRATTON.COM
Not for
Reproduction
10
AR Rev C_80010169
BRIGGS & STRATTON
Briggs & Stratton
.BRIGGSandSTRATTON.COM
**
Briggs & Stratton Briggs & Stratton *
**
[email protected]
1300 274 447 BRIGGSandSTRATTON.COM
.Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170
.Briggs & Stratton
.Briggs & Stratton
-
Briggs & Stratton
-
-
-
( E15 E85 )
-
24 3
24 3
3
Not for
Reproduction
4 BRIGGSandSTRATTON.COM4 BRIGGSandSTRATTON.COM
.....................4
............................5
..........................................5
................................5
........................................5
...............................8
..........................................9
.......... 10
................................... 10
.......................................... 11
би могла
би могла
БЕЛЕЖКА
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
(
6
!
OFF/
ON/
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
Simplicity 020632-00 Kasutusjuhend
- Tüüp
- Kasutusjuhend
- See käsiraamat sobib ka
teistes keeltes
- slovenčina: Simplicity 020632-00 Používateľská príručka
- română: Simplicity 020632-00 Manual de utilizare
