Hilti TE 30A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

TE 30A36

English 1

Dansk 11

Svenska 22

Norsk 33

Suomi 44

Türkçe 55

Srpski 66

ﻋﺮﺑﻲ 78

Latviešu 90

Lietuvių 101

Eesti 112

日本語 123

한국어 134

繁體中文 145

中文 155

1

2

3

4

5

6

7

8

9

TE 30A36

en Originaloperatinginstructions....................................... 1

da Originalbrugsanvisning .......................................... 11

sv Originalbruksanvisning........................................... 22

no Originalbruksanvisning .......................................... 33

fi Alkuperäisetohjeet ............................................. 44

tr Orijinalkullanımkılavuzu ......................................... 55

sr Originalnouputstvozaupotrebu .................................... 66

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 78

lv Oriģinālālietošanasinstrukcija ..................................... 90

lt Originalinaudojimoinstrukcija...................................... 101

et Originaalkasutusjuhend .......................................... 112

ja オリジナル取扱説明書 ............................................ 123

ko 오리지널사용설명서............................................. 134

zh 原始操作說明.................................................. 145

cn 原版操作说明.................................................. 155

*2173712* 2173712 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbers in illustrations refer to important work steps or to components important for the

work steps. In the text, the corresponding numbers draw attention to these work steps or compo-

nents, e.g. (3).

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

This symbol is intended to draw your special attention to certain points for handling the product.

2 English 2173712 *2173712*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Drilling without hammer action

Drilling with hammer action (hammer drilling)

Chiseling

Chisel positioning

Forward / reverse

Diameter

Rated speed under no load

Revolutions per minute

The product supports wireless data transmission compatible with iOS and Android platforms.

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

Li-ion battery

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Combihammer TE 30A36

Generation 03

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

*2173712* 2173712 English 3

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

4 English 2173712 *2173712*

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Hammer safety warnings

Safety instructions for all operations

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

▶Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

▶Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher

speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in

personal injury.

▶Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend

causing breakage or loss of control, resulting in personal injury.

2.3 Additional safety instructions for breakers

Personal safety

▶Use the product and accessories only when they are in perfect working order.

▶Never tamper with or modify the product or accessories in any way.

▶When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A

sudden break-through can affect your balance!

▶Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶You and the other persons in the vicinity must wear suitable eye protection, a hard hat, ear protection,

protective gloves and light respiratory protection while the product is in use.

▶Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in

cuts and burns.

▶Wear eye protection. Flying fragments can injure the body and eyes.

*2173712* 2173712 English 5

▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some

examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone

and other products containing silicates; certain types of wood, such as oak, beech and chemically

treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and

bystanders by means of the hazard classification of the materials to be worked. Implement the necessary

measures to restrict exposure to a safe level, for example by the use of a dust collection system or by

the wearing of suitable respiratory protection. The general measures for reducing exposure include:

▶working in an area that is well ventilated,

▶avoidance of prolonged contact with dust,

▶directing dust away from the face and body,

▶wearing protective clothing and washing exposed areas of the skin with water and soap.

▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the product could give you an electric shock or cause an explosion if you

accidentally damage an electric cable or a gas or water pipe.

Power tool use and care

▶Wait until the product has come to a complete stop before you lay it down.

3 Description

3.1 Product overview 1

@Chuck

;Depth gauge release button

=Depth gauge

%Function selector switch

&Forward / reverse switch

(Control switch

)Battery state of charge / fault display

+Release buttons / battery state of charge

display

§Battery

/Side handle

3.2 Intended use

The product described is a cordless (battery-powered) combihammer with pneumatic hammering mecha-

nism. It is designed for drilling in concrete, masonry, wood and metal. The product can also be used for light

to medium-duty chiseling on masonry and surface finishing work on concrete.

▶Use only Hilti Li-ion batteries from the B 36 series with this product.

▶Use only the Hilti battery chargers from the C4/36 series for these batteries.

3.3 Possible misuse

• This product is not suitable for working on hazardous materials.

• This product is not suitable for working in a damp environment.

3.4 ATC

The product is equipped with the ATC (Active Torque Control) quick-acting electronic cut-out.

If the accessory tool sticks or stalls, the product will suddenly pivot about its own axis in the opposite direction.

ATC detects this sudden pivoting movement of the product and switches the product off immediately.

6 English 2173712 *2173712*

For ATC to function correctly, the product must be free to pivot.

After an ATC cut-out, switch the product off and then on again.

3.5 Motor protection system

The tool is equipped with a motor protection system. The system monitors current input and motor

temperature and thus prevents the tool from overheating.

If the motor is overloaded through application of excessive working pressure, the power tool’s performance

drops noticeably or it may stall completely.

If the power tool stalls or slows significantly due to overloading, release the pressure applied to the tool and

then allow it to run under no load for approx. 30 seconds.

3.6 Lithiumion battery status display

The Li-ion battery state of charge and malfunctions of the power tool are indicated by the display on the Liion

battery. The Liion battery state of charge is displayed after pressing one of the two battery release buttons.

Status Meaning

4 LEDs light. State of charge: 75 % to 100 %

3 LEDs light. State of charge: 50 % to 75 %

2 LEDs light. State of charge: 25 % to 50 %

1 LED lights. State of charge: 10 % to 25 %

1 LED blinks. State of charge: < 10 %

1 LED blinks, the power tool is not ready for use. The battery has overheated or is completely dis-

charged.

4 LEDs blink, the power tool is not ready for use. The power tool is overloaded or has overheated.

Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch.

If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.

3.7 Items supplied

Combihammer, side handle with depth gauge, operating instructions.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Center or online at: www.hilti.com

4 Technical data

4.1 Technical data

TE 30A36

Rated voltage 36 V

Single impact energy in accordance with EPTA procedure 05/2009 3.6 J

Weight 5.1 kg

4.2 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

*2173712* 2173712 English 7

An accurate estimation of exposure should also take into account the times when the power tool is switched

off, or when it is running but not actually being used for a job. This can significantly reduce exposure over

the total working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

TE 30A36

Sound power level (LWA)103 dB

Sound pressure level (LpA)92 dB

Uncertainty for the sound power level / sound level 3 dB

Total vibration

TE 30A36

Drilling in metal (a h, HD)5 m/s²

Hammer drilling in concrete (a h, HD) B 36/5.2 10.3 m/s²

B 36/9.0 9.3 m/s²

Chiseling B 36/5.2 8.5 m/s²

B 36/9.0 7.3 m/s²

Uncertainty 1.5 m/s²

5 Operation

5.1 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1.1 Inserting the battery 2

1. Push the battery into the battery holder until it engages with an audible click.

2. Check that the battery is seated securely.

5.1.2 Removing the battery 3

1. Press the release buttons on the battery.

2. Pull the battery out toward the rear.

5.1.3 Charging the battery

Make sure that the outer surfaces of the battery are clean and dry before inserting the battery in the

approved battery charger.

Read the operating instructions for the charger for further information about the charging process.

▶Use an approved charger to charge the battery.

5.1.4 Fitting the side handle 4

CAUTION

Risk of injury! Loss of control over the product.

▶Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is

engaged in the groove in the product.

1. Release the side handle clamping band by turning the handle grip.

2. Slide the side handle clamping band over the tool holder from the front and into the recess provided.

8 English 2173712 *2173712*

3. Set the side handle to the desired position.

4. Tighten the side handle clamping band by turning the handle grip.

5.1.5 Adjusting the depth gauge (optional) 5

1. Press the release button on the side handle.

2. Adjust the depth gauge to the desired drilling depth.

3. Release the release button.

4. Check that the side handle is securely attached.

5.1.6 Removing the chuck 6

CAUTION

Risk of injury. The depth gauge, if fitted but not used, might hinder the operator.

▶Remove the depth gauge from the product.

Set the function selector switch to the “Chiseling” position for changing the chuck.

1. Remove the battery from the tool.

2. Grip the chuck as shown in the illustration and pull the three chuck release rings upwards.

3. Lift the chuck upwards away from the tool.

5.1.7 Fitting the chuck 6

CAUTION

Risk of injury. The depth gauge, if fitted but not used, might hinder the operator.

▶Remove the depth gauge from the product.

When changing the chuck, set the function selector switch to this position: .

1. Remove the battery from the tool.

2. Grip the chuck as shown in the illustration and pull the three chuck release rings upwards.

3. Fit the chuck onto the chuck mount.

4. Rotate the chuck until it engages in position.

5.1.8 Inserting the tool 7

1. Lightly grease the connection end of the accessory tool.

▶Use only genuine Hilti grease. Using the wrong grease can result in damage to the tool.

2. Push the accessory tool into the chuck as far as it will go (until it engages).

3. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.

▶The product is ready for use.

5.1.9 Removing the accessory tool 7

CAUTION

Risk of injury by the accessory tool! The accessory tool might be hot or have sharp edges.

▶Wear protective gloves when changing the accessory tool.

▶Pull the tool lock back as far as it will go and remove the accessory tool.

5.2 Types of work

CAUTION

Risk of damage by incorrect handling!

▶Do not operate the switches for direction of rotation and/or function selection during operation.

Observe the safety instructions and warnings in this documentation and on the product.

*2173712* 2173712 English 9

5.2.1 Function selector switch 8

▶Set the function selector switch to the desired working position.

▶Do not operate the function selector switch while the motor is running. Risk of damage!

5.2.2 Drilling without hammering

▶Set the function selector switch to this symbol: .

5.2.3 Drilling with hammering action (hammer drilling)

▶Set the function selector switch to this symbol: .

5.2.4 Chisel positioning

▶Set the function selector switch to this symbol: .

▶The chisel can be adjusted to 12 different positions (in 30° increments). This ensures that flat chisels

and shaped chisels can always be set to the optimum working position.

5.2.5 Chiseling

▶Set the function selector switch to this symbol: .

5.2.6 Forward / reverse 9

▶Set the forward / reverse switch to the desired direction of rotation.

6 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with your product can be found at your

Hilti Store or online at: www.hilti.group

10 English 2173712 *2173712*

7 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

8 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

8.1 The combihammer is in working order.

Trouble or fault Possible cause Action to be taken

The battery runs down more

quickly than usual. Battery condition is not optimal. ▶Replace the battery.

The battery doesn’t engage

with an audible click. The retaining lugs on the battery

are dirty.

▶Clean the retaining lugs and refit

the battery.

The control switch can’t be

pressed, i.e. the switch is

locked.

The forward / reverse switch is in

the middle position.

▶Push the forward / reverse

switch to the right or left.

The drive spindle doesn’t

rotate. The permissible operating temper-

ature of the combihammer’s elec-

tronics has been exceeded.

▶Allow the combihammer to cool

down.

Battery is discharged. ▶Change the battery and charge

the empty battery.

The combihammer switches

itself off automatically. The overload cut-out has been

activated.

▶Release the control switch.

Allow the combihammer to cool

down. Press the control switch

again. Reduce the load on the

tool.

*2173712* 2173712 Dansk 11

Trouble or fault Possible cause Action to be taken

The combihammer or the

battery gets very hot. Electrical fault. ▶Switch the combihammer off

immediately. Remove the

battery and keep it under

observation. Allow it to cool

down. Contact Hilti service.

The combihammer has been over-

loaded (application limits exceed-

ed).

▶Select a tool that is suitable for

the intended purpose.

The insert tool can’t be re-

leased. Chuck not pulled back fully. ▶Pull the tool lock back as far

as it will go and remove the

accessory tool.

The drill bit makes no

progress. The combihammer is set to run in

reverse rotation.

▶Move the forward / reverse

selector switch to the “Forward”

position.

8.2 The combihammer is not in working order.

Malfunction Possible cause Action to be taken

No LEDs light. The battery is not fully inserted. ▶Push the battery in until it

engages with a click.

Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Bring the battery to the recom-

mended working temperature.

1 LED blinks. Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Bring the battery to the recom-

mended working temperature.

4 LEDs blink. The combihammer has been over-

loaded briefly.

▶Release the control switch and

then press it again.

The overheating prevention cut-out

has been activated.

▶Allow the combihammer to cool

down and clean the air vents.

9 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

10 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

Original brugsanvisning

1 Om brugsanvisningen

1.1 Om denne brugsanvisning

• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde

og korrekt håndtering.

• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.

12 Dansk 2173712 *2173712*

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer

sammen med denne brugsanvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:

FARE

FARE !

▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.

ADVARSEL

ADVARSEL !

▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.

FORSIGTIG

FORSIGTIG !

▶Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.

1.2.2 Symboler i brugsanvisningen

Der benyttes følgende symboler i denne brugsanvisning:

Se brugsanvisningen

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald

Hilti lithium-ion-batteri

Hilti Lader

1.2.3 Symboler i illustrationer

Følgende symboler anvendes på illustrationer:

Disse tal henviser til den pågældende illustration i begyndelsen af denne brugsanvisning.

Nummereringen i illustrationerne henviser til vigtige arbejdstrin eller for arbejdstrin til vigtige

komponenter. I teksten fremhæves disse arbejdstrin eller komponenter med tilhørende numre,

f.eks. (3).

Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i

afsnittet Produktoversigt.

Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.

1.3 Produktspecifikke symboler

1.3.1 Symboler på produktet

Følgende symboler anvendes på produktet:

Boring uden slagfunktion

Boring med slagfunktion (hammerboring)

Mejsling

*2173712* 2173712 Dansk 13

Placering af mejsel

Højre-/venstreløb

Diameter

Nominelt omdrejningstal, ubelastet

Omdrejninger pr. minut

Produktet understøtter trådløs dataoverførsel, som er kompatibel med iOS- og Android-platforme.

Anvendt Hilti lithium-ion-batteriserie. Overhold oplysningerne i kapitlet Tilsigtet anvendelse.

Lithium-ion-batteri

Brug aldrig batteriet som slagværktøj.

Lad ikke batteriet falde på gulvet. Brug ikke et batteri, der har fået et slag eller på anden vis er

beskadiget.

1.4 Produktoplysninger

-produkter er beregnet til professionel brug og må kun betjenes, efterses og vedligeholdes af

autoriseret og instrueret personale. Dette personale skal i særdeleshed informeres om de potentielle farer,

der er forbundet med anvendelsen af denne maskine. Der kan opstå farlige situationer ved anvendelse af

produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke er blevet undervist i dens brug,

eller hvis det ikke anvendes korrekt i henhold til forskrifterne i denne brugsanvisning.

Typebetegnelse og serienummer fremgår af typeskiltet.

▶Notér serienummeret i den efterfølgende tabel. Du skal bruge produktoplysningerne ved henvendelser til

vores lokale afdeling eller vores serviceværksted.

Produktoplysninger

Kombihammer TE 30A36

Generation 03

Serienummer

1.5 Overensstemmelseserklæring

Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med gældende direktiver og

standarder. Sidst i dette dokument finder du et bilede af overensstemmelseserklæringen.

Den tekniske dokumentation er arkiveret her:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sikkerhed

2.1 Generelle sikkerhedsanvisninger for elværktøj

ADVARSEL Læs alle sikkerhedsanvisninger, henvisninger, billedtekster og tekniske data på

elværktøjet. Hvis følgende anvisninger ikke overholdes, er der risiko for elektrisk stød, brand og/eller

alvorlige personskader.

Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.

Det benyttede begreb "elværktøj" i sikkerhedsanvisningerne refererer til elektriske maskiner (med netledning)

eller batteridrevne maskiner (uden netledning).

Arbejdspladssikkerhed

▶Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden eller uoplyste arbejdsområder

øger faren for uheld.

▶Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er brændbare væsker, gasser eller

støv. Elværktøj kan slå gnister, der kan antænde støv eller dampe.

14 Dansk 2173712 *2173712*

▶Sørg for, at andre personer og ikke mindst børn holdes væk fra arbejdsområdet, når elværktøjet

er i brug. Hvis man distraheres, kan man miste kontrollen over maskinen.

Elektrisk sikkerhed

▶Elværktøjets stik skal passe til kontakten. Stikket må under ingen omstændigheder ændres. Brug

ikke adapterstik sammen med jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,

nedsætter risikoen for elektrisk stød.

▶Undgå kropskontakt med jordforbundne overflader som f.eks. rør, radiatorer, komfurer og

køleskabe. Hvis din krop er jordforbundet, øges risikoen for elektrisk stød.

▶Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand i elværktøj øger risikoen for

elektrisk stød.

▶Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må man aldrig bære elværktøjet i

ledningen, hænge det op i ledningen eller rykke i ledningen for at trække stikket ud af kontakten).

Beskyt ledningen mod varme, olie, skarpe kanter eller dele, der er i bevægelse. Beskadigede eller

sammenviklede ledninger øger risikoen for elektrisk stød.

▶Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlængerledning, der er egnet til

udendørs brug. Brug af forlængerledning til udendørs brug nedsætter risikoen for elektrisk stød.

▶Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser, skal du anvende et

fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ nedsætter risikoen for et elektrisk stød.

Personlig sikkerhed

▶Det er vigtigt at være opmærksom, se, hvad man laver, og bruge maskinen fornuftigt. Anvend aldrig

elværktøj, hvis du er træt eller påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed

under brugen af elværktøjet kan medføre alvorlige personskader.

▶Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af sikkerhedsudstyr som f.eks.

støvmaske, skridsikkert fodtøj, beskyttelseshjelm eller høreværn afhængigt af elværktøjets type og

anvendelse nedsætter risikoen for personskader.

▶Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er frakoblet, før du slutter det til

strømforsyningen og/eller batteriet, tager det op eller transporterer det. Undgå at bære elværktøjet

med fingeren på afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da dette øger

risikoen for personskader.

▶Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tændes. Hvis et stykke værktøj eller en

nøgle sidder i en roterende maskindel, er der risiko for personskader.

▶Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert, mens der arbejdes, og kom

ikke ud af balance. Det er derved nemmere at kontrollere elværktøjet, hvis der skulle opstå uventede

situationer.

▶Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller smykker. Hold hår, tøj og handsker

væk fra dele, der bevæger sig. Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller

langt hår.

▶Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det vigtigt, at dette tilsluttes og

benyttes korrekt. Ved at anvende en støvudsugning er det muligt at nedsætte risiciene som følge af

støv.

▶Man må ikke ignorere sikkerhedsreglerne for elværktøj, heller ikke selvom man er fortrolig med

brugen af elværktøjet. Uagtsomhed kan medføre alvorlig tilskadekomst inden for få sekunder.

Anvendelse og pleje af elværktøjet

▶Undgå at overbelaste maskinen. Brug altid en maskine, der er beregnet til det stykke arbejde,

der skal udføres. Med det rigtige værktøj arbejder man bedst og mest sikkert inden for det angivne

effektområde.

▶Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke kan startes og stoppes, er farlig

og skal repareres.

▶Træk stikket ud af stikkontakten, og/eller fjern batteriet fra maskinen, inden du foretager

indstillinger på den, skifter tilbehør og dele eller lægger den til side. Disse sikkerhedsforanstaltninger

forhindrer utilsigtet start af elværktøjet.

▶Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad aldrig personer, der ikke er

fortrolige med maskinen eller ikke har gennemlæst sikkerhedsanvisningerne, benytte denne.

Elværktøj er farligt, hvis det benyttes af ukyndige personer.

▶Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige dele fungerer korrekt og

ikke sidder fast, og om delene er brækket eller beskadiget, således at elværktøjets funktion

påvirkes. Få beskadigede dele repareret, inden elværktøjet tages i brug. Mange uheld skyldes

dårligt vedligeholdte elværktøjer.

▶Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt vedligeholdte skæreværktøjer med

skarpe skærekanter sætter sig ikke så hurtigt fast og er nemmere at føre.

Leht laadib ...

Hilti TE 30A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

Hilti TE 30A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid

Hilti TE 30­A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

Hilti TE 30­A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid

Hilti TE 30A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend

Hilti TE 30A36 Cordless SDS Plus Rotary Hammers Kasutusjuhend