In the box
BE1350 Classic alarm clock
BE1272 Bed shaker with sound
Power supply
User manual
Power and battery
Mains power
7.5 V DC / 1000 mA
External power supply unit
Backup batteries
4 x 1.2 V AAA NiMH rechargeable
batteries (not included)
Battery backup operating time
~ 24 h when fully charged
Battery backup charging time
~ 10 h from fully depleted
Output signals
Sound
100 dBA @ 10 cm, 94 dBA @ 30 cm
Multiple frequencies: 950 Hz - 3 kHz
Bed shaker
Vibrator power: 2.0 - 4.0 V DC
Environmental requirements
For indoor use only
Temperature: 32° to 95° F, 0°-35° C
Relative humidity: 5% -95%
Non-condensing
Accessories
BE1270 Bed shaker
Dimensions and weight
Height: 108 mm, 4.3"
Width: 121 mm, 4.7"
Depth: 92 mm, 3.6"
Weight: 300 g, 10.6 oz. excl. batteries
Alarm and snooze
Alarm timeout: 20 minutes
Decreasing snooze time interval
from 9 to 2 minutes
Snooze timeout: 20 minutes
Display
Type: Twisted Nematic LCD
Adjustable backlight in 5 steps
Display timeout: 8 seconds
Technical specications
Alarm clock Classic
Time dial
Sound on/o
Alarm on/o
Buttons and controls
Alarm dialSnooze
Wakeup time Speaker
Time formatBacklight
Bed shaker
Power supply
(The appearance may dier with territory)
BE1350
Getting started
1 Connect the bed shaker on the back of the alarm clock.
2 Connect the power supply to the alarm clock and the mains
outlet to turn it on.
3 Tuck the bed shaker under the pillow or mattress and place the
alarm clock on the bedside table.
Setting the time
Press the left dial and turn it to set hours.
To set minutes, press and turn the dial again.
Press once again to save your settings.
Setting the alarm
Press the right dial and turn it to set hours.
To set minutes, press and turn the dial again.
Press once again to save your settings.
Using the snooze
Press the snooze button briey to snooze the alarm.
The snooze time interval will automatically decrease
from 9 to 2 minutes in 2 minute steps.
Activating the alarm
Press the alarm on/o button to activate the alarm.
The alarm symbol appears on the clock face.
To turn o the alarm, press the button again.
1
2
The appearance may
dier with territory
Alarm clock Classic
Alarm clock Classic
Settings
Sound on/o
Press the sound on/o button marked with on the back of the alarm clock to turn on/o the sound. A symbol will
appear on the clock face when the sound is muted.
Display backlight
Press the button marked with repeatedly to adjust the intensity in 4 steps. Step 5 results in permanent backlight.
Time format
Press the time format button marked with 12/24h on the back of the alarm clock to toggle between a 24h and a 12h setting.
Using battery backup
The alarm clock features a battery backup function
that steps in when the power goes out. It keeps the
alarm clock and bed shaker going for about 24 hours
(when the batteries are fully charged).
Here is how you install backup batteries:
1 Remove the battery cover on the bottom of the
alarm clock using a Philips screwdriver.
2 insert 4 x 1.2 V AAA NiMH rechargeable batteries
and put the cover back on.
Troubleshooting
Most problems with the alarm clock can be solved quickly by following the advice below.
If Try this
The alarm clock seems to be turned o
Check that the power supply is connected correctly, see Getting started.
Charge the backup batteries (not included) for a couple of hours.
The symbol on the clock face
starts to blink
The power supply is disconnected and the backup batteries are nearly depleted.
Connect the power supply and charge the batteries for a couple of hours.
A symbol appears on the clock face
The alarm clock detects no backup batteries. Open the battery cover and t four
1.2 V AAA NiMH rechargeable batteries.
A symbol appears on the clock face
The sound is muted. Press the sound on/o button marked with until the
symbol disappears if you wish to turn it back on.
The display is too bright or too dark or
I want it to be permanently lit
Press the button marked with repeatedly to adjust the intensity in 4 steps.
Choose step 5 that results in permanent backlight.
The bed shaker does not vibrate
Make sure it’s connected properly to the alarm clock, see Getting started.
The alarm volume is too low
The volume increases gradually and reaches over 100 dB.
Warning! ONLY USE RECHARGEABLE NiMH BATTERIES. Non-rechargeable batteries will start to leak and the
battery acid will damage the electronics. The resulting damage is not covered by warranty.
-
1
-
2
-
3
teistes keeltes
- English: Bellman BE1350 User manual
Seotud paberid
Muud dokumendid
-
Philips Dusk Kasutusjuhend
-
Silvercrest SWE 100 B1 User Manual And Service Information
-
Silvercrest WE-2300 Kasutusjuhend
-
Auriol H14371 Operation and Safety Notes
-
Marathon CL030065 Kasutusjuhend
-
Silvercrest KH 2029 Operating Instructions Manual
-
Denver CRP-514 Kasutusjuhend
-
Denver CRL-330 Kasutusjuhend
-
-