Hilti TE 60-A36 Kasutusjuhend

TE 60-A36

English 1

Dansk 13

Svenska 25

Norsk 38

Suomi 50

Eesti 63

Latviešu 75

Lietuvių 88

Türkçe 100

ﻋﺮﺑﻲ 114

日本語 127

한국어 139

繁體中文 151

中文 163

1

2

3

4

5

6

7

8

TE 60-A36

en Originaloperatinginstructions....................................... 1

da Originalbrugsanvisning .......................................... 13

sv Originalbruksanvisning........................................... 25

no Originalbruksanvisning .......................................... 38

fi Alkuperäisetohjeet ............................................. 50

et Originaalkasutusjuhend .......................................... 63

lv Oriģinālālietošanasinstrukcija ..................................... 75

lt Originalinaudojimoinstrukcija...................................... 88

tr Orijinalkullanımkılavuzu ......................................... 100

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 114

ja オリジナル取扱説明書 ............................................ 127

ko 오리지널사용설명서............................................. 139

zh 原廠操作說明.................................................. 151

cn 原版操作说明.................................................. 163

*2202100* 2202100 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbers in illustrations refer to important work steps or to components important for the

work steps. In the text, the corresponding numbers draw attention to these work steps or compo-

nents, e.g. (3).

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

This symbol is intended to draw your special attention to certain points for handling the product.

2 English 2202100 *2202100*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Drilling with hammering action (hammer drilling)

Chiseling

Chisel positioning

Protection class II (double-insulated)

Revolutions per minute

Rated speed under no load

Diameter

Direct current (DC)

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

The product supports wireless data transmission compatible with iOS and Android platforms.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Switching on and off

Symbols

Product is switched on

Product is switched off

1.5 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Combihammer TE 60A36

Generation 04

Serial no.

1.6 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

*2202100* 2202100 English 3

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

4 English 2202100 *2202100*

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Hammer safety warnings

Safety instructions for all operations

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

▶Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

▶Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher

speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in

personal injury.

▶Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend

causing breakage or loss of control, resulting in personal injury.

2.3 Additional safety instructions for rotary hammer drill

Personal safety

▶Use the product and accessories only when they are in perfect working order.

*2202100* 2202100 English 5

▶Never tamper with or modify the product or accessories in any way.

▶Use auxiliary handles supplied with the product. Loss of control can cause personal injury.

▶Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶Always hold the tool with both hands on the grips provided. Keep the grips clean and dry.

▶Hold the product by the insulated gripping surfaces when performing work in which the accessory tool

might come into contact with concealed wiring. If the accessory tool comes into contact with a live wire,

metal parts of the power tool can also become live, resulting in an electric shock.

▶Do not touch rotating parts – risk of injury!

▶Wear eye protection, a hard hat and ear protection and suitable respiratory protection while the product

is in use.

▶Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in

cuts and burns.

▶Wear eye protection. Flying fragments can injure the body and eyes.

▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some

examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone

and other products containing silicates; certain types of wood, such as oak, beech and chemically

treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and

bystanders by means of the hazard classification of the materials to be worked. Implement the necessary

measures to restrict exposure to a safe level, for example by the use of a dust collection system or by

the wearing of suitable respiratory protection. The general measures for reducing exposure include:

▶working in an area that is well ventilated,

▶avoidance of prolonged contact with dust,

▶directing dust away from the face and body,

▶wearing protective clothing and washing exposed areas of the skin with water and soap.

▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the product could give you an electric shock or cause an explosion if you

accidentally damage an electric cable or a gas or water pipe.

Power tool use and care

▶Switch the product off immediately if the accessory tool jams. The product might twist off-line.

▶Wait until the product has come to a complete stop before you lay it down.

3 Description

3.1 Product overview 1

@Chuck

;Depth gauge adjustment (accessory)

=Depth gauge (accessory)

%Function selector switch

&Lockbutton for sustained operation (chiseling

only)

(Control switch

)Charge-status and fault indicator (Li-ion bat-

tery)

+Release buttons (also used to activate the

charge status indicator)

§Battery

/Side handle

:On/off switch

∙Button for half power

$Half-power indicator

£Service indicator

|ON/OFF indicator

6 English 2202100 *2202100*

3.2 Intended use

The product described is an electrically powered combihammer with pneumatic hammering mechanism. It

is designed for drilling in concrete, masonry, wood and metal. The product can also be used for light- to

medium-duty chiseling on masonry and surface finishing work on concrete.

▶Use only Hilti Li-ion batteries from the B 36 series with this product.

▶Use only the Hilti battery chargers from the C4/36 series for these batteries.

3.2.1 Possible misuse

• This product is not suitable for working on hazardous materials.

• This product is not suitable for working in a damp environment.

3.3 Undercut anchors

The product is suitable for setting undercut anchors. Use only suitable setting tools.

Detailed information on this topic can be obtained at your local Hilti Center.

3.4 ATC

The product is equipped with the ATC (Active Torque Control) quick-acting electronic cut-out.

If the accessory tool sticks or stalls, the product will suddenly pivot about its own axis in the opposite direction.

ATC detects this sudden pivoting movement of the product and switches the product off immediately.

For ATC to function correctly, the product must be free to pivot.

After an ATC cut-out, switch the product off and then on again.

3.5 Active Vibration Reduction

The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.

3.6 Quick-release chuck (accessory)

The quick-release chuck makes changing accessory tools a quick operation with no additional tools needed.

It is suitable for accessory tools with cylindrical or hexagonal shank used in the "With hammering action "

mode.

3.7 Service indicator

The product is equipped with a service indicator LED.

3.7.1 MMI

Status Meaning

The Service indicator lights up. Servicing is due.

The Service indicator flashes. Have the product repaired by Hilti Service.

The ON/OFF indicator lights up. The product is switched on

The ON/OFF indicator flashes. The product is switched off because of a transient

fault.

The ON/OFF indicator is off. The product is switched off.

The Half power indicator lights up. The product is working at half power.

The Half power indicator is off. The product is working at full power.

3.7.2 Lithiumion battery status display

The Li-ion battery state of charge and malfunctions of the power tool are indicated by the display on the Liion

battery. The Liion battery state of charge is displayed after pressing one of the two battery release buttons.

Status Meaning

4 LEDs light. State of charge: 75 % to 100 %

3 LEDs light. State of charge: 50 % to 75 %

2 LEDs light. State of charge: 25 % to 50 %

*2202100* 2202100 English 7

Status Meaning

1 LED lights. State of charge: 10 % to 25 %

1 LED blinks. State of charge: < 10 %

1 LED flashes, the product is not in working order. The battery has overheated or is completely dis-

charged.

4 LEDs flash, the product is not in working order. The power tool is overloaded or has overheated.

Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch.

If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.

3.8 Items supplied

Combihammer, side handle, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Store or online at:

www.hilti.group | USA: www.hilti.com

4 Technical data

TE 60-A36

Rated voltage 36 V

Weight in accordance with EPTA procedure 01 8.1 kg

Single impact energy in accordance with EPTA procedure 05 8.1 J

Hammer drill bits, Ø 12 mm … 55 mm

Breach bits, Ø 40 mm … 80 mm

Percussion core bits, Ø 45 mm … 100 mm

PCM diamond core bits, Ø 42 mm … 102 mm

Drill bits for metal, Ø 10 mm … 20 mm

Drill bits for wood, Ø 10 mm … 32 mm

Chuck TEY

4.1 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the power tool is switched

off, or when it is running but not actually being used for a job. This can significantly reduce exposure over

the total working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

TE 60-A36

Sound pressure level LpA 98 dB

Uncertainty for the sound pressure level (KpA) 3 dB

Sound power level LWA 109 dB

Uncertainty for the sound power level (KWA) 3 dB

8 English 2202100 *2202100*

Total vibration

Hammer drilling in concrete (ah, HD) B 36/5.2 LiIon 9.0 m/s²

Chiseling in concrete (ah, Cheq) B 36/5.2 LiIon 8.6 m/s²

Uncertainty (K) 1.5 m/s²

5 Operation

5.1 Preparations at the workplace

Switch the product off or remove the battery before making adjustments or changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1.1 Removing the battery 2

1. Press the release buttons on the battery.

2. Pull the battery out toward the rear.

5.1.2 Fitting the side handle 3

CAUTION

Risk of injury Loss of control over the product.

▶Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is

engaged in the groove in the product.

CAUTION

Risk of injury. The depth gauge, if fitted but not used, might hinder the operator.

▶Remove the depth gauge from the product.

1. Release the side handle clamping band by turning the handle grip.

2. Slide the side handle clamping band over the tool holder from the front and into the recess provided.

3. Set the side handle to the desired position.

4. Tighten the side handle clamping band by turning the handle grip.

5.1.3 Fitting the depth gauge (optional) 4

1. Release the side handle clamping band by turning the handle grip.

2. Slide the depth gauge from the front into the 2 guide holes provided.

3. Secure the side handle by turning the knob until the clamping band is tight.

5.1.4 Setting the power level

After the battery is inserted, the product is always set by default to full power.

1. Press the "button for half power". The product runs at half power.

▶The "half power indicator" lights up.

2. Press the "button for half power" again. The product runs at full power.

▶The "half power indicator" goes out.

5.1.5 Inserting / removing the accessory tool 5

DANGER

Risk of fire! Risk of contact between the hot accessory tool and highly inflammable materials.

▶Do not lay the hot accessory tool down on highly inflammable materials.

*2202100* 2202100 English 9

CAUTION

Risk of injury by the accessory tool! The accessory tool might be hot or have sharp edges.

▶Wear protective gloves when changing the accessory tool.

The use of unsuitable grease can cause damage to the product. Use only genuine Hilti grease.

1. Apply a little grease to the connection end of the accessory tool.

▶Use only genuine Hilti grease. Using the wrong grease can result in damage to the product.

2. Push the accessory tool into the chuck as far as it will go (until it engages).

3. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.

▶The product is ready for use.

4. Pull the chuck ring back as far as it will go and remove the accessory tool.

5.1.6 Inserting the battery 6

WARNING

Electrical hazard! Risk of short circuiting.

▶Before inserting the battery, check to ensure that the battery terminals and the contacts on the

combihammer are free from foreign objects.

WARNING

Risk of injury! Hazard presented by a falling battery.

▶A falling battery may present a risk of injury to yourself and others. Check that the battery is securely

seated in the combihammer.

1. Push the battery into the battery holder until it engages with an audible click.

2. Check that the battery is seated securely.

5.2 Types of work

CAUTION

Risk of injury Loss of control over the product.

▶Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is

engaged in the groove in the product.

Observe the safety instructions and warnings in this documentation and on the product.

5.2.1 Drilling with hammering action (hammer drilling)

1. Set the function selector switch to this symbol: .

2. Set the desired power level.

3. Press the drill bit against the work surface.

4. Press the control switch.

▶The product starts.

5.2.2 Drilling without hammer action

Drilling without hammering action is possible when accessory tools with a special connection end

are used. Accessory tools of this kind are available from Hilti. Alternatively, when the keyless quick-

release chuck is fitted, smooth-shank drill bits for wood or steel, for example, can be used to drill

without hammering.

▶Set the function selector switch to this symbol: .

10 English 2202100 *2202100*

5.3 Chisel positioning 7

CAUTION

Risk of injury! Loss of control over the chisel direction.

▶Do not operate the tool when the selector switch is set to “Chisel positioning”. Turn the function selector

switch until it engages in the “Chiseling” position.

The chisel can be set to 24 different positions (in 15° increments). This ensures that flat chisels and

shaped chisels can always be set to the optimum working position.

1. Set the function selector switch to the "Chisel positioning” position .

2. Turn the chisel to the desired position.

3. Set the function selector switch to this symbol: until it engages.

▶The product is ready for use.

5.3.1 Chiseling

▶Set the function selector switch to the "Chiseling" position .

5.3.2 Switch sustained operation on and off 8

When chiseling, the control switch can be locked in the “on” position.

1. Push the lockbutton for continuous operation forward.

2. Press the control switch fully.

▶The product then runs in sustained operating mode.

3. Push the lockbutton for continuous operation back.

▶The product switches off.

6 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

*2202100* 2202100 English 11

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with your product can be found at your

Hilti Store or online at: www.hilti.group

7 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

8 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances: qr.hilti.com/r8377057.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

No hammering action. The product is too cold. ▶Bring the product into contact

with the working surface, switch

it on and allow it to idle. If

necessary, repeat the procedure

until the hammering mechanism

begins to operate.

12 English 2202100 *2202100*

Trouble or fault Possible cause Action to be taken

The battery runs down more

quickly than usual. Battery condition is not optimal. ▶Replace the battery.

The battery does not en-

gage with an audible "double

click".

The retaining lugs on the battery

are dirty.

▶Clean the retaining lugs and refit

the battery.

The drive spindle does not

rotate. The permissible operating temper-

ature of the product’s electronics

has been exceeded.

The ON/OFF indicator flashes.

▶Allow the product to cool down.

Battery is discharged. ▶Change the battery and charge

the empty battery.

Product switches off auto-

matically. The overload protection system is

active. The ON/OFF indicator flashes.

▶Release the control switch.

Allow the product to cool down.

Press the control switch again.

Reduce the load on the tool.

Product switches off if drill bit

jams. The electronic safety shut-down

has tripped to avoid further jam-

ming.

▶Release the drill bit.

The combihammer or the

battery gets very hot. Electrical fault. ▶Immediately switch off the

product. Remove the battery

and keep it under observation.

Allow it to cool down. Contact

Hilti service.

The product is overloaded (appli-

cation limit exceeded).

▶Select a product that is suitable

for the intended purpose.

No response from the LEDs

on the battery. The battery is not fully inserted. ▶Push the battery in until it

engages with a double click.

Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Bring the battery to the recom-

mended working temperature.

1 LED on the battery flashes. Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Bring the battery to the recom-

mended working temperature.

4 LEDs on the battery flash. Product momentarily overloaded. ▶Release the control switch and

then press it again.

Protection against overheating. ▶Allow the product to cool down

and clean the air vents.

Product does not develop full

power. The control switch is not fully

pressed.

▶Press the control switch as far

as it will go.

The half-power button is engaged. ▶Press the "half-power" button.

Drill bit does not rotate. The function selector switch is not

engaged or is in the "Chiseling"

position or the "Chisel position-

ing" position .

▶With the motor at a standstill,

set the function selector switch

to the "Hammer drilling"

position.

The insert tool cannot be re-

leased from the chuck. The chuck is not pulled back fully. ▶Pull the chuck back as far

as it will go and remove the

accessory tool.

The side handle is not fitted cor-

rectly.

▶Disengage the side handle and

refit it correctly so that the

clamping band and side handle

engage in the recess.

*2202100* 2202100 Dansk 13

Trouble or fault Possible cause Action to be taken

Product does not start. The electronic restart interlock is

activated after an interruption in

the electric supply.

▶Switch the product off and then

on again.

The service indicator lights. Service limit time reached. ▶Have the product repaired by

Hilti Service.

The service indicator blinks. The product is faulty. ▶Have the product repaired by

Hilti Service.

The ON/OFF indicator

flashes. Product momentarily overloaded. ▶Release the control switch and

then press it again.

Protection against overheating. ▶Allow the product to cool down

and clean the air vents.

10 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

Original brugsanvisning

1 Om brugsanvisningen

1.1 Om denne brugsanvisning

• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde

og korrekt håndtering.

• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer

sammen med denne brugsanvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:

FARE

FARE !

▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.

ADVARSEL

ADVARSEL !

▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.

FORSIGTIG

FORSIGTIG !

▶Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.

14 Dansk 2202100 *2202100*

1.2.2 Symboler i brugsanvisningen

Der benyttes følgende symboler i denne brugsanvisning:

Se brugsanvisningen

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald

Hilti lithium-ion-batteri

Hilti Lader

1.2.3 Symboler i illustrationer

Følgende symboler anvendes på illustrationer:

Disse tal henviser til den pågældende illustration i begyndelsen af denne brugsanvisning.

Nummereringen i illustrationerne henviser til vigtige arbejdstrin eller for arbejdstrin til vigtige

komponenter. I teksten fremhæves disse arbejdstrin eller komponenter med tilhørende numre,

f.eks. (3).

Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i

afsnittet Produktoversigt.

Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.

1.3 Produktspecifikke symboler

1.3.1 Symboler på produktet

Følgende symboler anvendes på produktet:

Boring med slagfunktion (hammerboring)

Mejsling

Placering af mejsel

Kapslingsklasse II (dobbeltisoleret)

Omdrejninger pr. minut

Nominelt omdrejningstal, ubelastet

Diameter

Jævnstrøm

Lithium-ion-batteri

Anvendt Hilti lithium-ion-batteriserie. Overhold oplysningerne i kapitlet Tilsigtet anvendelse.

Produktet understøtter trådløs dataoverførsel, som er kompatibel med iOS- og Android-platforme.

Brug aldrig batteriet som slagværktøj.

Lad ikke batteriet falde på gulvet. Brug ikke et batteri, der har fået et slag eller på anden vis er

beskadiget.

Leht laadib ...

Hilti TE 60-A36 Kasutusjuhend

Hilti TE 60-A36 Kasutusjuhend

teistes keeltes

Seotud paberid