ADB TV Box Guide
Problem
Resolution
ADB Box
TV Not
working?
Power On? Confirm that the power light is green on the front of your ADB set top box (box with clock on
the front). If it is red push the “STB” button and then the Power button on the ADB remote. The red light
means that the set top box is turned off; the green light indicates it is on.
No Picture
or Sound?
If your TV loses sound, picture, or freezes press the “Reset” button on the front of the set top box to the
left of the clock. If you have a DVR (Digital Video Recorder), unplug the power (black cord) from the back
for a few seconds and then plug it back in. The DVR box does not have a reset button on the front. This
will reboot the box and will allow it to reload all settings. This process can take three or four minutes and
when complete your TV will come back on to Channel 1. At this point you can go back to what you were
watching.
-If your TV is on the wrong Input or Channel, you may not have picture or sound. Should this happen,
check to make sure your TV is on channel 3 if hooked up with a coax cable. You can use your regular TV
remote or press the “TV” button on the ADB remote and type 03 on the keypad to get the TV back on
Channel 3. This also happens when your TV is on the wrong Input for A/V inputs. To check the inputs
you can use your regular TV remote or press the “TV” button on the ADB remote, and at the bottom of
the ADB remote on the left side press the “TV/Video Input” button. This button will switch between
inputs on your TV. Once you are on the correct Input your picture and sound should return. After your
TV is back on the correct channel or Input, press the “STB button” to put the set top box back in control.
ADB
For Information on Programing the Remote see the Guide Section on the website.
Connect the Set Top Box to your TV using one of the options below.
Good - Coaxial Cable
Connect one end of the coaxial cable to RF Out on the STB and the other to the RF IN on your TV
(consult your TV manual). Your TV will need to be tuned to channel 3 in order to view programming. This
is a Non HD connection.
Better - Analog AV cable
Composite Non-HD Video/Audio
yellow=video
white=left audio
black (black plugs into red audio on tv) =right audio
Component HD Video/Audio
red, blue, green=video
white (white to white on TV) =left audio
black (black plugs into red audio on tv) =right audio
Connect the specialized cable end to the AV output of the STB and the other ends to your TV using
either composite in or component in on your TV. This will require that your TV to be set to a video input
of Video or COMP in order to view programming (consult your TV manual).
Best - HDMI Cable
Digital Video and audio HD delivery. Connect one end of the HDMI cable to the HDMI port on the STB
and the other to your TV. This will require that your TV to be set to a video input of HDMI in order to
view programming (consult your TV manual).
Note: Arrow to Arrow. Arrow on the cable connector that
must match up to the Arrow on the box. Make sure flat
spot lines up. Important: If not matched up correctly the
pins bend/break easily and the box it will not work.
-
1
-
2
-
3
teistes keeltes
- English: ADB 3721wn User manual
Muud dokumendid
-
Samsung LE22C330F2W Lühike juhend
-
Samsung LE32B541P7W Kasutusjuhend
-
Samsung LE32B350F1W Kasutusjuhend
-
Regent HT-391 Kasutusjuhend
-
Pioneer VSX-531D Kasutusjuhend
-
Luxor LX9411962DVD Operating Instructions Manual
-
Samsung LE40S73BD Omaniku manuaal
-
Luxor LX94119DVD Operating Instructions Manual
-
Finlux 19FLD841UD Omaniku manuaal
-