Husqvarna LB 146i Lawn Mower Kasutusjuhend

LB 146i

EN Operator's manual 2-22

BG Ръководство за експлоатация 23-46

CS Návod k použití 47-68

DA Brugsanvisning 69-90

DE Bedienungsanweisung 91-113

EL Οδηγίες χρήσης 114-137

ES Manual de usuario 138-160

ET Kasutusjuhend 161-180

FI Käyttöohje 181-200

FR Manuel d'utilisation 201-223

HR Priručnik za korištenje 224-244

HU Használati utasítás 245-267

IT Manuale dell'operatore 268-289

JA 取扱説明書 290-310

LT Operatoriaus vadovas 311-332

LV Lietošanas pamācība 333-354

NL Gebruiksaanwijzing 355-377

NO Bruksanvisning 378-398

PL Instrukcja obsługi 399-421

PT Manual do utilizador 422-444

RO Instrucţiuni de utilizare 445-466

RU Руководство по эксплуатации 467-491

SK Návod na obsluhu 492-513

SL Navodila za uporabo 514-534

SR Priručnik za rukovaoca 535-556

SV Bruksanvisning 557-577

TR Kullanım kılavuzu 578-598

UK Посібник користувача 599-622

Contents

Introduction..................................................................... 2

Safety..............................................................................4

Assembly...................................................................... 11

Operation...................................................................... 12

Maintenance................................................................. 15

Troubleshooting............................................................ 17

Transportation, storage and disposal........................... 19

Technical data.............................................................. 19

EC Declaration of Conformity....................................... 22

Introduction

Product description

The product is a pedestrian-controlled rotary lawn

mower that usesBioClip to cut the grass into fertilizer.

Intended use

Use the product to cut grass. Do not use the product for

other tasks.

Product overview

1

16

19

10

13

14

11

6

8

18

7

17

12

3

4

15

5

9

12

1. Control panel

2. Motor brake handle

3. Start inhibitor

4. Upper handle

5. Lower handle

6. Cutting cover

7. Cutting height control

8. Safety key

9. Battery cover

10. ON/OFF button

11. SavE button

12. Battery charge indicator and battery button

13. Blade

14. Spring washer

21680 - 003 - 26.11.2021

15. Blade bolt

16. Operator's manual

17. Battery charger (Accessory)

18. Battery (Accessory)

19. Rating plate with QR code

Symbols on the product

Warning: Not careful or

incorrect use can result

in injury or death for the

operator or others.

Read the operator's

manual carefully and

make sure that you

understand the

instructions before use.

Keep persons and

animals at a safe

distance from the work

area.

Look out for thrown

objects and ricochets.

Warning: Keep hands

and feet away from the

rotating blade.

Warning: Keep hands

and feet away from

rotating parts.

Remove the safety key

before you do repair

work or maintenance.

Do not expose to rain

The product or package

of the product is not

domestic waste.

Recycle it at a recycling

station for electrical and

electronic equipment.

The product agrees with applicable EC

directives.

The product agrees with

applicable Eurasian

Customs Union

directives.

The product agrees with

applicable UkrSEPRO

directives.

The product agrees with

applicable RCM

directives. Applies to

AU/NZ only

Noise emission to the

environment according

to the European

Community’s Directive.

The product’s emission

is specified in the

Technical data chapter

and on the label.

IPX1 - Drip protected

1680 - 003 - 26.11.2021 3

Start proce-

dure: push the

ON/OFF but-

ton, loosen the

start inhibitor,

push the motor

brake handle

down.

Release the motor brake

handle to stop.

Note: Other symbols/decals on the product refer to

certification requirements for some markets.

Label on the product

DANGER – Keep hands and feet away.

Product liability

As referred to in the product

liability laws, we are not liable

for damages that our product

causes if:

•the product is incorrectly

repaired.

•the product is repaired with

parts that are not from the

manufacturer or not approved

by the manufacturer.

•the product has an accessory

that is not from the

manufacturer or not approved

by the manufacturer.

•the product is not repaired at

an approved service center or

by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes

are used to point out specially

important parts of the manual.

WARNING: Used if there

is a risk of injury or death

for the operator or

bystanders if the

instructions in the

manual are not obeyed.

CAUTION: Used if there

is a risk of damage to the

product, other materials

or the adjacent area if

the instructions in the

manual are not obeyed.

41680 - 003 - 26.11.2021

Note: Used to give more

information that is necessary in

a given situation.

General safety instructions

WARNING: Read the

warning instructions that

follow before you use the

product.

•This product is dangerous if

used incorrectly or if you are

not careful. Injury or death can

occur if you do not obey the

safety instructions.

•This product produces an

electromagnetic field during

operation. This field may

under some circumstances

interfere with active or passive

medical implants. To reduce

the risk of serious or fatal

injury we recommend persons

with medical implants to

consult their physician and the

medical implant manufacturer

before operating this product.

•Always be careful and use

your common sense. If you

are not sure how to operate

the product in a special

situation, stop and speak to

your Husqvarna dealer before

you continue.

•Keep in mind that the operator

will be held responsible for

accidents that involve other

persons or their property.

•Keep the product clean. Make

sure that you can clearly read

signs and decals.

•Never allow children or people

unfamiliar with these

instructions to use the

appliance. Local regulations

may restrict the age of the

operator

•Always monitor a person, with

decreased physical capacity or

mental capacity, that uses the

product. A responsible adult

must be there at all times.

•Do not use the product if you

are tired, ill, or under the

influence of alcohol, drugs or

medicine. This has a negative

effect on your vision,

alertness, coordination and

judgment.

•Do not use the product if it is

defective.

•Do not change this product or

use it if it is possible that it has

been changed by others.

Work area safety

WARNING: Read the

warning instructions that

follow before you use the

product.

1680 - 003 - 26.11.2021 5

•Remove objects such as

branches, twigs and stones

from the work area before you

use the product.

•Objects that hit against the

cutting equipment can eject

and cause damage to persons

and objects. Keep bystanders

and animals at a safe distance

from the product.

•Never use the product in bad

weather such as fog, rain,

strong winds, intense cold and

risk of lightning. To use the

product in bad weather or in

moist or wet locations is tiring.

Bad weather can cause

dangerous conditions, such as

slippery surfaces.

•Look out for persons, objects

and situations that can prevent

safe operation of the product.

•Look out for obstacles, such

as roots, stones, twigs, pits

and ditches. Long grass can

hide obstacles.

•To cut grass on slopes can be

dangerous. Do not mow

excessively steep slopes. Do

not use the product on ground

that slopes more than 15°

•Exercise extreme caution

when changing direction on

slopes. Operate the product

across the face of slopes. Do

not move up and down.

•Be careful when you go near

hidden corners and objects

that prevent a clear view.

Work safety

WARNING: Read the

warning instructions that

follow before you use the

product.

•Use this product to cut grass

lawns only. It is not permitted

to use it for other tasks.

•Use personal protective

equipment. Refer to

Personal

protective equipment on page

7

.

•Make sure that you know how

to stop the motor quickly in an

emergency.

•Do not operate the product in

rain or wet conditions. The risk

of electrical shock increases if

water enters the product.

•Do not operate the product

unless the blade and all

covers are attached correctly.

An incorrectly attached blade

can come loose and cause

personal injury.

•Make sure that the blade does

not hit objects such as stones

and roots. This can do

damage to the blade and bend

the motor shaft. A bent axle

causes heavy vibration and a

61680 - 003 - 26.11.2021

very high risk that the blade

becomes loose.

•If the blade hits an object or if

vibrations occur, stop the

product immediately. Stop the

motor, turn the safety key to 0

and remove the battery.

Examine the product for

damages. Repair damages or

let an authorised service agent

do the repair.

•Never attach the motor brake

handle permanently to the

handle when the motor is

started.

•Put the product on a stable,

flat surface and start it. Make

sure that the blade does not

hit the ground or other objects.

•Always stay behind the

product when you operate it.

•Let all the wheels stay on the

ground and keep 2 hands on

the handle when you operate

the product. Keep your hands

and feet away from the

rotating blades.

•Do not tilt the product when

the motor is started.

•Be careful when you pull the

product rearward.

•Never lift up the product when

the motor is started. If you

must lift the product, first stop

the motor, turn the safety key

to 0 and remove the battery.

•Do not walk rearward when

you operate the product.

•Stop the motor when you

move across areas without

grass, for example paths

made of gravel, stone and

asphalt.

•Do not run with the product

when the motor is started.

Always walk when you operate

the product.

•Stop the motor before you

change the cutting height.

Never make adjustments with

the motor started.

•Never let the product stay out

of view with the motor started.

Stop the motor and make sure

that the cutting equipment

does not rotate.

Safety instructions for operation

Personal protective equipment

WARNING: Read the

warning instructions that

follow before you use the

product.

•Personal protective equipment

cannot fully prevent injury but

it decreases the degree of

injury if an accident does

occur. Let your dealer help

you select the right equipment.

•Use heavy-duty slip-resistant

boots or shoes. Do not use

1680 - 003 - 26.11.2021 7

open shoes or go with bare

feet.

•Use heavy, long pants.

•Use protective gloves when

necessary, for example when

you attach, examine or clean

the cutting equipment.

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. If the

safety devices are defective, speak to your

Husqvarna service agent.

To do a check of the cutting cover

The cutting cover decreases vibrations in the product

and decreases the risk of injury from the blade.

• Examine the cutting cover to make sure that there

are no damages such as cracks.

Safety key

The safety key is below the battery lid. The safety key

connects the battery that supplies the motor with power.

• Start and stop the motor to do a check of the safety

key.

• If the safety key operates correctly, the motor can

only start when the safety key is in position 1.

Motor brake handle

The motor brake handle stops the motor. When the

motor brake handle is released, the motor stops.

To do a check of the motor brake, start the motor and

then release the motor brake handle. If the motor does

not stop in 3 seconds, let an approved Husqvarna

service agent adjust the motor brake.

To examine the start inhibitor

Do a check of the start inhibitor to make sure that it

prevents operation of the motor.

1. Push the motor brake handle in the direction of the

handlebar. The start inhibitor stops the movement.

2. Push the start inhibitor out.

3. Release the start inhibitor and make sure that it goes

back to its initial position.

Battery safety

WARNING: Read the

warning instructions that

follow before you use the

product.

•Use Husqvarna rechargeable

batteries as a power supply for

related Husqvarna products

only. To prevent injury, do not

81680 - 003 - 26.11.2021

use the battery as a power

supply for other devices.

•Do not use non-rechargeable

batteries.

•Risk of electrical shock. Do not

connect the battery terminals

to keys, coins, screws or other

metal. This can cause a short

circuit of the battery.

•Do not put objects into the air

slots of the battery.

•Keep the battery away from

sunlight, heat or open flame.

The battery can explode and

cause burns and/or chemical

burns.

•Keep the battery away from

rain and wet conditions.

•Keep the battery away from

microwaves and high

pressure.

•Do not try to disassemble or

break the battery.

•If the battery leaks, do not let

the liquid touch your body or

eyes. If you have touched the

liquid, clean the area with a

large quantity of water and get

medical aid.

•Use the battery in

temperatures between -10°C

and 40°C.

•Do not clean the battery or the

battery charger with water.

See

To clean the battery and

the battery charger on page

16

.

•Do not use a defective or

damaged battery.

•Keep batteries in storage

away from metal objects such

as nails, coins, jewellery.

Battery charger safety

WARNING: Read the

warning instructions that

follow before you use the

product.

•Use the QC battery chargers

to charge Husqvarna

replacement batteries only.

•Risk of electrical shock or

short circuit. Do not put

objects into the air slots of the

charger. Do not try to

disassemble the battery

charger. Do not connect the

charger terminals to metal

objects. Use an approved

mains socket.

•This product produces an

electromagnetic field during

operation. This field may

under some circumstances

interfere with active or passive

medical implants. To reduce

the risk of serious or fatal

injury, we recommend persons

with medical implants to

consult their physician and the

1680 - 003 - 26.11.2021 9

medical implant manufacturer

before operating this product.

•Regularly make sure that the

power cord of the battery

charger is not damaged and

that there are no cracks in it.

•Do not lift the battery charger

by the power cord. To

disconnect the battery charger

from a mains socket, pull out

the plug. Do not pull the power

cord.

•Keep the power cord and

extension cables away from

water, oil and sharp edges.

Make sure that the cable is not

pinched in doors, fences or

equivalent. It can cause the

charger to become energized.

•Do not clean the battery

charger with water.

•The battery charger can be

used by children aged from 8

years and above and persons

with reduced physical,

sensory, or mental capabilities

or lack of experience and

knowledge if they have been

given supervision or

instruction concerning use of

the battery charger in a safe

way and understand the

hazards involved. Children

shall not play with the battery

charger. Cleaning and user

maintenance shall not be

made by children without

supervision.

•Do not charge non-

rechargeable batteries in the

battery charger.

•Do not use the battery charger

near flammable materials or

materials that can cause

corrosion. Do not cover the

battery charger. Pull out the

plug to the battery charger if

there is smoke or fire.

•Do not use a defective or

damaged battery charger.

•Only charge the battery

indoors in a room with good

airflow and away from

sunlight. Do not charge the

battery in wet conditions.

Safety instructions for

maintenance

WARNING: Read the

warning instructions that

follow before you use the

product.

•To prevent accidental start

during maintenance, turn the

safety key to 0 and remove the

battery. Wait at minimum 5

seconds before you start the

maintenance.

•Do the maintenance work

correctly to increase the

lifetime of the product and

10 1680 - 003 - 26.11.2021

decrease the risk of accidents.

Let an approved service agent

do the professional repairs.

Speak to your nearest service

agent for more information.

•Only do the maintenance work

written in this operator's

manual. More extensive work

must be done by an approved

service agent.

•Put on heavy duty gloves

when you use the cutting

equipment. The blade is very

sharp and cuts can easily

occur.

•Keep the cutting edges sharp

and clean for the best and

safest performance.

•Let your service agent

regularly examine the product

and make necessary

adjustments and repairs.

•Replace damaged, worn or

broken parts.

•Obey the instructions for how

to change accessories. Only

use accessories from the

manufacturer.

•When not in operation, keep

the product, battery and

battery charger apart in a dry,

indoor and locked area. Make

sure that children and persons

that are not approved cannot

get access to the product,

battery or battery charger.

Assembly

Introduction

WARNING: Before you assemble the

product, read the safety chapter.

WARNING: To prevent accidental start

during assembly, turn the safety key to 0,

remove the battery and wait at minimum 5

seconds.

To assemble the handle

CAUTION: Do not twist the cables.

1. Align the holes in the upper handle with the holes in

the lower handle.

2. Tighten the knobs on right and left sides fully and

fold the handle up.

1680 - 003 - 26.11.2021 11

3. Put the stay in the groove on the cutting cover.

4. Attach the 2 stops that lock the stay and the handle.

Push them fully into position.

Note: There are 2 stops, one identified with an H

and one with a V. Put the stop with an H on the right

side and the stop with a V on the left side.

CAUTION: Do not operate the

product if the 2 stops are not attached.

To adjust the handle height

1. Remove the handle stay from the lower handle.

a) Put the handle stay in the top hole (A) to

decrease the handle height.

b) Put the handle stay in the bottom hole (B) to

increase the handle height.

A

B

Operation

Introduction

WARNING: Before you operate the

product, you must read and understand the

safety chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.

The Husqvarna Connect app gives extended functions

for your Husqvarna product:

• Extended product information.

• Information about, and help with, product parts and

servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.

3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

12 1680 - 003 - 26.11.2021

To set the cutting height

• Press the shaft out and move it to the correct

position for each of the 4 wheels.

CAUTION: Do not set the cutting height

too low. The blades can hit the ground if the

surface of the lawn is not level.

Battery

WARNING: Before you use the battery,

you must read and understand the safety

chapter. You must also read and understand

the operator's manual for the battery and the

battery charger.

Battery status

The display shows the remaining battery capacity and if

there are problems with the battery. The battery capacity

is shown for 5 seconds after the product is switched off

or the battery indicator button is pressed. The warning

symbol on the battery is on when an error has occurred.

See

Battery on page 17

.

LED lights Battery status

All LEDs are lit Fully charged (75-100%)

LED 1, LED 2, LED 3 are

lit

The battery is 50%-75%

charged

LED 1, LED 2 are lit The battery is 25%-50%

charged

LED lights Battery status

LED 1 is lit The battery is 0%-25%

charged.

LED 1 flashes The battery is empty.

Charge the battery.

To charge the battery

Charge the battery before the first use. The battery is

only 30% charged when supplied to the customer.

Note: The battery charger must be connected to the

voltage and frequency specified on the rating plate.

The battery does not charge if the battery temperature is

above 50°C. The battery charger decreases the

temperature of the battery before it starts to charge.

1. Connect one end of the power cord for the battery

charger into the socket of the battery charger.

2. Connect the other end of the power cord for the

battery charger in an grounded mains socket. The

LED on the battery charger flashes green one time.

3. Put the battery in the battery charger. The green light

on the charger comes on when the battery is

correctly connected to the battery charger.

4. When all LEDs on the battery have come on the

battery is fully charged. Charge the battery for

maximum 24 hours.

5. To disconnect the battery charger from the mains

socket, pull the plug, not the power cord.

6. Remove the battery from the battery charger.

Battery charging status

A Husqvarna Li-ion battery can be charged or used at all

charging levels. The battery is not damaged. A fully

1680 - 003 - 26.11.2021 13

charged battery will not decrease its charge when the

battery is left in the charger.

LED display Charging status

LED 1 flashes 0%-25%

LED 1 is lit, LED 2 flashes 25%-50%

LED 1, LED 2 are lit, LED

3 flashes

50%-75%

LED 1, LED 2, LED 3 are

lit, LED 4 flashes

75%-100%

LED 1, LED 2, LED 3,

LED 4 are lit

Fully charged

To start the product

1. Put a charged battery in battery compartment

number 1 below the battery lid. For longer operation

time, put a second charged battery in battery

compartment number 2.

2. Turn the safety key to 1.

3. Stay behind the product.

4. Press the ON/OFF button (A) on the control panel

and the green LED (B) comes on.

A

B

5. Loosen the start inhibitor.

6. Push the motor brake handle in the direction of the

handlebar.

To use the SavE function

The product has a battery saving function (SavE) that

gives longer operation time.

1. Press the SavE button (A) to start the function. The

green LED comes on.

A

B

2. Press the SavE button again to stop the function.

The green LED (B) goes out.

The SavE function stops automatically if the ground

conditions make it necessary to have a higher output.

The SavE function starts automatically when the ground

conditions lets it.

High load function

When the product cuts long or wet grass, the motor

automatically increases rpm. The motor goes back to

standard mode when high load is not necessary.

14 1680 - 003 - 26.11.2021

To stop the product

The product stops automatically if you do not operate it

for 10 minutes. Always turn the safety key to 0 before

you let the product out of view.

1. Release the motor brake handle to stop the motor.

2. Press the ON/OFF button (A) on the control panel

and the green LED (B) goes out.

A

B

3. Open the battery lid and turn the safety key to 0.

4. To remove the battery, press the two release buttons

and pull out the battery.

5. Charge the battery if it is weak. For more

information, see

To charge the battery on page 13

.

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

• Keep the cutting cover clean. Buildup from grass and

dirt on the inner side of the cutting cover can

decrease the cutting result. Refer to

To clean the

product on page 16

.

Maintenance

Introduction

WARNING: Before you do

maintenance, you must read and

understand the safety chapter.

For all servicing and repair work on the product, special

training is necessary. We guarantee the availability of

professional repairs and servicing. If your dealer is not a

service agent, speak to them for information about the

nearest service agent.

Maintenance schedule

The maintenance intervals are calculated from daily use

of the product. The intervals change if the product is not

used daily.

For maintenance identified with * see instructions in

Safety devices on the product on page 8

.

1680 - 003 - 26.11.2021 15

Each use Monthly Each

season

Do a general inspection X

Clean the product X

Do a check of the start inhibitor * X

Make sure that the safety devices on the product are not defective * X

Examine the cutting equipment X

Examine the cutting cover * X

Do a check of the motor brake handle * X

Make sure that the ON/OFF button operates correctly and is not defective X

Examine the battery for damage X

Do a check of the battery charge X

Make sure that the release buttons on the battery operates correctly and that the

battery locks into the product X

Examine the battery charger for damage and make sure that it operates correct-

ly. X

Examine the connections between the battery and the product. Also examine the

connection between the battery and the battery charger. X

To do a general inspection

• Make sure that the nuts and screws on the product

are tightened.

• Make sure that the cables on the product are not in a

position where they can get damaged.

To clean the product

• Clean plastic parts with a clean and dry cloth.

• Do not use water to clean the product. Water can

enter the battery or the motor and cause short circuit

or damage to the product.

• Do not use a high pressure washer to clean the

product.

• Do not flush water directly on the motor.

• Use a brush to remove leaves, grass and dirt.

To clean the battery and the battery

charger

WARNING: Do not clean the battery or

the battery charger with water.

• Make sure that the battery and the battery charger

are clean and dry before you put the battery into the

battery charger.

• Clean the battery terminals with compressed air or

use a soft and dry cloth.

• Clean the surfaces of the battery and the battery

charger with a soft and dry cloth.

To examine the cutting equipment

WARNING: To prevent accidental start,

turn the safety key to 0, remove the battery

and wait a minimum 5 seconds.

WARNING: Use protective gloves

when you do maintenance on the cutting

equipment. The blade is very sharp and cuts

can easily occur.

1. Examine the cutting equipment for damage or

cracks. Always replace a damaged cutting

equipment.

2. Look at the blade to see if it is damaged or blunt.

Note: It is necessary to balance the blade after it is

sharpened. Let a service center sharpen, replace and

balance the blade. If you hit an obstacle that causes the

product to stop, replace the damaged blade. Let the

service center estimate if the blade can be sharpened or

must be replaced.

16 1680 - 003 - 26.11.2021

To replace the blade

1. Lock the blade with a block of wood.

2. Remove the blade bolt.

3. Remove the blade.

4. Examine the blade support and blade bolt to see if

there are damages.

5. Examine the motor shaft to make sure that it is not

bent.

6. When you attach the new blade, point the angled

ends of the blade in the direction of the cutting cover.

7. Make sure that the blade is aligned with the center of

the motor shaft.

8. Lock the blade with a block of wood. Attach the

spring washer and tighten the bolt and washer with a

torque of 23–28 Nm.

9. Pull the blade around by hand and make sure that it

turns freely.

WARNING: Use heavy duty gloves.

The blade is very sharp and cuts can

easily occur.

10. Start the product to do a test of the blade. If the

blade is not correctly attached, there is vibration in

the product or the cutting result is unsatisfactory.

Troubleshooting

Battery

LED on the battery Cause Solution

The green LED flashes. The battery voltage is low. Charge the battery. Refer to

To charge the battery

on page 13

.

1680 - 003 - 26.11.2021 17

LED on the battery Cause Solution

The error LED flashes. The battery is weak. Charge the battery. Refer to

To charge the battery

on page 13

.

The temperature in the work environ-

ment is too high or too low.

Use the battery in temperatures between -10°C

and 40°C.

Overvoltage. Make sure that the mains voltage is the same as

on the rating plate on the product.

Remove the battery from the battery charger. Wait

5 seconds and try again to charge the battery. If

the problem continues, speak to an approved

service agent.

The error LED is on. The cell difference too much (1V). Speak to an approved service agent.

Battery charger

LED on the battery

charger

Cause Solution

The error LED flash-

es.

The temperature in the work en-

vironment is too high or too low.

Use the battery charger in temperatures between 5°C

and 40°C.

The error LED is on. Speak to an approved service agent.

Control panel

For problems, other than those in this section, speak to

your service agent.

Keypad Error code (Num-

ber of flashes)

Possible faults Possible action

Error LED flashes 3 The motor is overloaded Increase the cutting height. See

To set

the cutting height on page 13

.

5 The motor speed drops too

much, and the motor stops

10 The motor control is too hot Stop the motor and wait until it has be-

come cool

2 The blade is blocked To prevent accidental start turn the safe-

ty key to 0, remove the battery and wait

a minimum 5 seconds. Make sure that

the blade can rotate freely. If the prob-

lem continues, speak to an authorised

service agent

9 Battery error or no signal from

battery

Put the battery in the product correctly

and examine the battery connector. If the

error LED on the battery flashes, see

Battery on page 13

.

The product stops 8 The battery is weak Charge the battery. See

To charge the

battery on page 13

.

0 Battery connector failure Examine the battery connector

18 1680 - 003 - 26.11.2021

Transportation, storage and disposal

Introduction

WARNING: To prevent unintentional

start during transport turn the safety key

to ”0”, remove the battery and wait at least 5

seconds.

Transportation

• The Dangerous Goods Legislation requirements

apply to the contained Li-ion batteries.

• For commercial transports special requirements on

package and labels must be obeyed.

• Make sure that you obey the regulations for

dangerous material when you prepare the product

for transport. Local regulations can apply.

• Always remove the battery for transport.

• Put tape on the battery connectors and make sure

that the battery cannot move around during

transport.

• Attach the product during transport.

Storage

• Always remove the battery for storage.

• To prevent accidents, make sure that the battery is

not connected to the product during storage.

• Keep the battery charger in a closed and dry space.

• Keep the battery and the battery charger in a dry

space where there is no moisture or frost.

• Disconnect the battery from the battery charger

during storage.

• Do not keep the battery where static electricity can

occur. Do not keep the battery in a metal box.

• Keep the battery where the temperature is between

5°C and 25°C and out of sunlight.

• Keep the battery charger where the temperature is

between 5°C and 45°C and out of sunlight.

• Make sure that the battery is charged to 30% - 50%

before you put it in storage for long periods.

• Keep the product, battery and battery charger in a

locked area out of reach for children and not

approved persons.

• Clean the product and do a complete servicing

before you put the product in storage for a long time.

Disposal

Symbols on the product or the packaging of the product

indicate that this product cannot be handled as domestic

waste. It must be submitted to an appropriate recycling

station for the recovery of electrical and electronic

equipment.

By ensuring that this product is taken care of correctly,

you can help to counteract the potential negative impact

on the environment and people that can otherwise result

through the incorrect waste management of this product.

For more detailed information about recycling this

product, contact your municipality, your domestic waste

service or the shop from where you purchased the

product.

Technical data

LB 146i

Cutting motor

Motor type BLDC (brushless) 36V

Motor speed – SavE, rpm 2600

Motor speed – Nominal, rpm 3000

Motor speed – High load, rpm 3500

Motor output – max. kW 1.05

Motor output – Nominal, kW 0.9

1680 - 003 - 26.11.2021 19

LB 146i

Overcurrent limit (Current limit: 900W-27A) 27 (+/-) 1A

Weight

Weight without battery, kg 16.9

Battery 1

Type of battery Husqvarna Battery Series

Battery runtime

Battery runtime, min, (free run) with SavE activated, with one Husqvarna 5.2

Ah battery (BLi200).

77

Battery runtime, min, (free run) with standard mode activated, with one

Husqvarna 5.2 Ah battery (BLi200).

45

Noise emissions 2

Sound power level, measured dB (A) 90

Sound power level, guaranteed LWA dB (A) 91

Sound levels 3

Sound pressure level at the operators ear, dB (A) 79

Vibration levels 4

Handle, m/s20.9

Cutting equipment

Cutting height, mm 35-70 mm

Cutting width, cm 46

Blade BioClip

Article number 5947022-10

Approved batteries Type Battery capacity,

Ah

Voltage, V Weight, lb/kg

BLi20 Lithium-ion 4.0 36 2.6/1.2

BLi200 Lithium-ion 5.2 36 2.8/1.3

BLi300 Lithium-ion 9.4 36 4.2/1.9

1For best results and performance the Husqvarna battery BLi200 is recommended.

2Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive

2000/14/EC.

3Reported data for noise pressure level has a typical statistical dispersion (standard deviation) of 1.2 dB (A).

4Reported data for vibration level has a typical statistical dispersion (standard deviation) of 0.2 m/s2. Vibration

standard EN 60335-2-77:2017 chapter 20.105

20 1680 - 003 - 26.11.2021

Leht laadib ...

Husqvarna LB 146i Lawn Mower Kasutusjuhend

Husqvarna LB 146i Lawn Mower Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid