Philips RQ1285/16 Kasutusjuhend

User manual

Always here to help you

RQ1200 series

1

RQ1200 series

ENGLISH 4

БЪЛГАРСКИ 28

ČEŠTINA 54

EESTI 78

HRVATSKI 102

MAGYAR 126

ҚАЗАҚША 149

LIETUVIŠKAI 174

LATVIEŠU 198

POLSKI 222

ROMÂNĂ 246

РУССКИЙ 271

SLOVENSKY 296

SLOVENŠČINA 320

SRPSKI 344

УКРАЇНСЬКА 368

4

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at

www.philips.com/welcome.

Please read this user manual, as it contains information about the features

of this shaver as well as some tips to make shaving easier and more

enjoyable.

General description (Fig. 1)

A Shaver

1 Display

2 Shaver on/off button

3 Protection cap

4 RQ12 Shaving unit

5 Trimmer

6 Trimmer on/off slide

B RQ111 Beard Styler attachment (RQ1296, RQ1295, RQ1286, RQ1285,

RQ1275, RQ1265 only)

7 Hair length selector

8 Comb of Beard Styler attachment

C Foldable charger

D Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC,

RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC,

RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only)

9 ’Cleaning chamber empty’ symbol

10 Cleaning symbol

11 Drying symbol

12 Jet Clean System on/off button (RQ1008 only: and up/down button

for program selection)

13 Cleaning chamber release button

14 Shaver holder

E Cleaning brush

F HQ200 Cleaning uid (RQ1296CC, RQ1295CC, RQ1290CC,

RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC,

RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only)

G Pouch

H Adapter

Important

Read this important information carefully before you use the shaver,

the Jet Clean system (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC,

RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC,

RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only) and the charging

stand. Save this leaet for future reference.

ENGLISH

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this causes a hazardous situation.

- The shaver, the Jet Clean system and the charging stand are not

intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use

of these appliances by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with

the shaver, the Jet Clean system and the charging stand.

- Always unplug the shaver before you clean it under the tap.

Caution

- Never immerse the Jet Clean system or the charging stand in water

nor rinse it under the tap.

- Never use water hotter than 80°C to rinse the shaver.

- Do not use the shaver, Jet Clean system, adapter, charging stand or any

other part if it is damaged, as this may cause injury. Always replace a

damaged adapter, charging stand or part with one of the original type.

- Only use the Jet Clean system with the original HQ200 Jet Clean

solution.

- Always place the Jet Clean system on a stable, level and horizontal

surface to prevent leakage.

- When the Jet Clean system is ready for use, do not move it to prevent

leakage of cleaning uid.

- The Jet Clean system thoroughly cleans but does not disinfect your

shaver, therefore do not share the shaver with others.

- Never use compressed air, scouring pads, abrasive cleaning agents or

aggressive liquids such as petrol or acetone to clean the appliance.

- Water may leak from the socket at the bottom of the shaver when you

rinse it. This is normal and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Compliance with standards

- This shaver is waterproof and complies with the internationally

approved safety regulations. It is suitable for use in the bath or shower

and for cleaning under the tap. For safety reasons, the shaver can

therefore only be used cordlessly.

- The shaver and the Jet Clean system comply with all applicable

standards and regulations regarding exposure to electromagnetic elds.

General

- The adapter is equipped with an automatic voltage selector and is

suitable for mains voltages ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less than

24 volts.

- Maximum noise level: Lc = 69dB(A)

ENGLISH 5

The display

Note: Before you use the shaver for the rst time, remove the protective foil

from the display.

The various shaver types have different displays, which are shown in the

gures below.

- RQ1296, RQ1295, RQ1290, RQ1286, RQ1285, RQ1280

- RQ1275, RQ1265, RQ1261, RQ1260

- RQ1273, RQ1252, RQ1251, RQ1250

Charging

- Charging takes approx. 1 hour.

RQ129x, RQ128x

- When the shaver is charging, the minutes indication ashes.

- The shaving minutes increase until the shaver is fully charged.

- Quick charge: When the shaver contains enough energy for one shave,

the display shows 5 minutes in red.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging

lights work in the same way.

- When the shaver is charging, rst the bottom charging light ashes, then

the second charging light, and so on until the shaver is fully charged.

- Quick charge: When the shaver contains enough energy for one shave,

the bottom charging light alternately ashes orange and white.

MINUTES LEFT

ENGLISH6

Battery fully charged

RQ129x, RQ128x

- When the battery is fully charged, the minutes indication lights up

continuously. After approx. 30 minutes, the display automatically

switches off again.

Note: The shaver is equipped with an intelligent self-learning system that

monitors the shaver’s energy consumption and converts the remaining battery

capacity into shaving minutes. The energy consumption and therefore the

remaining number of shaving minutes depend on your skin and beard type

and your shaving behaviour (e.g. the use of shaving gel). If the number of

shaving minutes of the fully charged shaver is less than 60 minutes, this is

completely normal and does not mean that the battery capacity of the shaver

has diminished.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging

lights work in the same way.

- When the battery is fully charged, all charging lights light up

continuously. After approx. 30 minutes, the display automatically

switches off again.

Battery low

RQ129x, RQ128x

- When the battery is almost empty (when there are only 5 or fewer

shaving minutes left), the minutes indication starts to ash.

- When you switch off the shaver, the shaving minutes continue to ash

for a few more seconds. You hear a beep when there are no shaving

minutes left.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging

lights work in the same way.

- When the battery is almost empty (when there are only 5 or fewer

shaving minutes left), the bottom charging light ashes orange.

- When you switch off the shaver, the bottom charging light continues to

ash orange for a few seconds.

MINUTES LEFT

ENGLISH 7

Remaining battery capacity

RQ129x, RQ128x

- The remaining battery capacity is indicated by the number of shaving

minutes shown on the display.

RQ127x, RQ126x, RQ125x

Note: The displays of the various shaver types look different, but the charging

lights work in the same way.

- The remaining battery capacity is indicated by the ashing charging

lights.

Clean shaver

For optimal shaving performance, we advise you to clean the shaver after

every use.

Note: The displays of the various shaver types look different, but show the

same symbol.

- The tap symbol ashes to remind you to clean the shaver.

Replace shaving unit

For maximum shaving performance, we advise you to replace the shaving

unit every two years.

Note: The displays of the various shaver types look different, but show the

same symbol.

- To remind you to replace the shaving unit, the appliance is equipped

with a replacement reminder which is activated automatically after

approx. two years. The replacement reminder is repeated at 9

successive shaves(RQ128x, RQ127x, RQ126x, RQ125x only) or until

you reset the shaver.

Travel lock (RQ128x, RQ127x, RQ126x, RQ125x only)

You can lock the shaver when you are going to travel. The travel lock

prevents the shaver from being switched on by accident.

Note: The displays of the various shaver types look different, but show the

same symbol.

MINUTES LEFT

ENGLISH8

Activating the travel lock

1 Press the on/off button for 3 seconds to enter the travel lock mode.

, RQ128x: The display starts to count down from 3. At 1, the appliance

beeps to indicate that it is locked.

, The lock symbol lights up on the display. After a few seconds it goes

out.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The motor starts running to indicate that the travel lock has been

deactivated.

The shaver is now ready for use again.

Note: When you place the shaver in the plugged-in charger or Jet Clean System,

the travel lock is automatically deactivated.

Power-saving mode (RQ129x only)

The appliance is equipped with an automatic power-saving mode. When

the shaver enters the power-saving mode, the light in the on/off button

goes out to save energy.

- When the appliance is switched off but detects movement for 5

minutes (for instance when you are travelling with the shaver in your

suitcase), it automatically goes into power-saving mode. This mode

prevents the shaver from being switched on by accident.

, The lock symbol ashes on the display to indicate that the appliance

is in power-saving mode.

- To deactivate the power-saving mode, simply press the on/off button.

Blocked shaving heads

Note: The displays of the various shaver types look different, but show the

same symbol.

- If the shaving heads are blocked, the shaving unit symbol, the tap

symbol and the exclamation mark ash. In this case, the motor cannot

run because the shaving heads are soiled or damaged.

- When this happens, you have to clean the shaving unit or replace it.

- The shaving unit symbol, the tap symbol and the exclamation mark

continue to ash until you unblock the shaving heads.

Charging

Charging takes approx. 1 hour.

RQ129x, RQ128x, RQ127x, RQ126x: A fully charged shaver has a shaving

time of up to 60 minutes.

Note: RQ129x, RQ128x: When the battery is fully charged, the display shows

the actual remaining shaving minutes (see section ‘Battery fully charged’ in

chapter ‘The display’).

RQ125x: A fully charged shaver has a shaving time of up to 50 minutes.

Charge the shaver before you use it for the rst time and when the display

indicates that the battery is almost empty (see section ‘Battery low’ in

chapter ‘The display’).

MINUTES LEFT

ENGLISH 9

Quick charge

After the shaver has charged for 3 minutes, it contains enough energy for

one shave.

Charging in the charger

1 Insert the small plug into the charger.

2 Unfold the charger (‘click’).

3 Put the adapter in the wall socket.

4 Put the shaver in the charger.

, The display shows that the shaver is charging (see chapter ‘The

display’).

Charging in the Jet Clean System (RQ1296CC, RQ1295CC,

RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC, RQ1280CC,

RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC, RQ1251CC,

RQ1250CC only)

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

3 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

Note: The shaver cannot be placed in the Jet Clean System when the protection

cap is on the shaving unit.

Note: RQ129x only: when you turn the shaver upside down, the minutes

indication on the display is also turned upside down so you can still see to what

level the battery is charged.

ENGLISH10

4 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

, The display shows that the shaver is charging (see section ‘Charging’

in chapter ‘The display’).

Using the shaver

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you expect and your skin

may even become slightly irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times a week) for a period of

3 weeks to allow your skin to adapt to the new shaver. During this period,

use your new electric shaver exclusively and do not use other shaving

methods. If you use different shaving methods, it is more difcult for your

skin to adapt to the new shaving system.

1 Press the on/off button once to switch on the shaver.

, The display lights up for a few seconds.

2 Move the shaving heads over your skin in circular movements.

- Do not make straight movements.

3 Press the on/off button once to switch off the shaver.

, The display lights up for a few seconds and then shows the remaining

battery capacity.

Wet shaving

You can also use this shaver on a wet face with shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure that the shaving unit

glides smoothly over your skin.

4 Press the on/off button once to switch on the shaver.

5 Move the shaving heads over your skin in circular movements.

Note: Rinse the shaver under the tap regularly to ensure that it continues to

glide smoothly over your skin.

6 Dry your face and thoroughly clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

ENGLISH 11

Trimming

You can use the trimmer to groom your sideburns and moustache.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

2 Press the on/off button once to switch on the shaver.

, The display lights up for a few seconds.

3 Slide the trimmer slide forwards to slide out the trimmer.

4 You can now start trimming.

5 Slide the trimmer slide backwards to retract the trimmer.

6 Press the on/off button once to switch off the shaver.

, The display lights up for a few seconds and shows the remaining

battery capacity.

7 Insert the lug of the shaving unit into the slot in the top of the shaver

(1). Then press down the shaving unit (2) to attach it to the shaver

(‘click’).

Using the Beard Styler attachment (RQ1296, RQ1295, RQ1286,

RQ1285, RQ1275, RQ1265 only)

1 Make sure the shaver is switched off.

2 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

ENGLISH12

3 Insert the lug of the Beard Styler attachment into the slot in the top

of the shaver (1). Then press down the beard styler attachment (2)

to attach it to the shaver (‘click’).

Using the Beard Styler attachment with comb

You can use the Beard Styler attachment with the comb attached to style

your beard at one xed setting, but also at different length settings. The

hair length settings on the Beard Styler attachment correspond to the

remaining hair length after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding grooves on both sides of the

beard styler attachment (‘click’).

2 Press the length selector (1) and then push it to the left or right (2)

to select the desired hair length setting.

3 Press the on/off button on the shaver to switch it on.

4 You can now start styling your beard.

Using the Beard Styler attachment without comb

You can use the Beard Styler attachment without the comb to contour

your beard, moustache or sideburns.

ENGLISH 13

1 Pull the comb off the Beard Styler attachment.

Note: Grab the comb in the centre to pull it off the Beard Styler attachment.

Do not pull at the sides of the comb.

2 Press the on/off button to switch on the shaver.

3 You can now start contouring your beard, moustache, sideburns or

neckline.

Beard styles

Below you nd some examples of beard styles you can create.

- A stubble look

- A full beard

ENGLISH14

- A moustache

- A goatee

Cleaning and maintenance

Never use scouring pads, abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the shaver, its accessories and the

Jet Clean System (RQ1296CC, RQ1295CC, RQ1290CC, RQ1286CC,

RQ1285CC, RQ1284CC, RQ1280CC, RQ1275CC, RQ1265CC,

RQ1260CC, RQ1252CC, RQ1251CC, RQ1250CC only).

- The best and most hygienic way to clean the shaver is in the Jet Clean

System. You can also rinse the shaver under the tap or clean it with the

cleaning brush supplied.

- Be careful with hot water. Always check if the water is not too hot, to

prevent your hands from getting burnt.

- Clean the shaver after every shave for optimal shaving performance.

- You can clean the outside of the shaver with a damp cloth.

- Regular cleaning guarantees better shaving performance.

Cleaning the shaving unit

Be careful with hot water. Always check if the water is not too hot, to

prevent your hands from getting burnt.

1 Rinse the shaving unit under a hot tap for some time.

ENGLISH 15

2 Pull open the three shaving heads one by one.

3 Rinse all three shaving heads and all three hair chambers under a hot

tap for 30 seconds.

Note: You can also brush the shaving heads and hair chambers with the

cleaning brush supplied.

Be careful with hot water. Always check if the water is not too hot, to

prevent your hands from getting burnt.

4 Carefully shake off excess water and leave the shaving heads open to

let the shaving unit dry completely.

Never dry the shaving unit with a towel or tissue, as this may damage the

shaving heads.

Cleaning the shaving unit in the Jet Clean System (RQ1296CC,

RQ1295CC, RQ1290CC, RQ1286CC, RQ1285CC, RQ1284CC,

RQ1280CC, RQ1275CC, RQ1265CC, RQ1260CC, RQ1252CC,

RQ1251CC, RQ1250CC only)

The Jet Clean System comes in two types:

- Type RQ1008 has three cleaning programs: the eco program, the auto

program and the intensive program. Press the up/down button to

select the cleaning program you prefer.

Note: The eco program has a shorter drying time, to save energy. The intensive

program is a more thorough cleaning program.

- Type RQ1007 has one automatic cleaning program. When you

press the on/off button, the Jet Clean System starts cleaning in the

automatic cleaning program.

Preparing the Jet Clean System for use

Fill the cleaning chamber before rst use.

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

, The holder automatically moves to the highest position.

ENGLISH16

3 Simultaneously press the release buttons on both sides of the

cleaning chamber (1). Then lift the Jet Clean System off the cleaning

chamber (2).

, The cleaning chamber remains behind.

4 Unscrew the cap from the bottle with HQ200 cleaning uid.

5 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

6 Place the Jet Clean System back onto the cleaning chamber.

Make sure the release buttons click back into place.

Using the Jet Clean System

Note: If you use the shaver with shaving foam or shaving gel, we advise you

to rinse it under the hot tap before you clean it in the Jet Clean System. This

guarantees an optimal lifetime for the cleaning uid.

1 Hold the shaver upside down above the holder with the back of the

shaver pointing towards the holder.

2 Place the shaver body in the holder behind the two clips (1) and

press it down until it locks into place (2).

, The display shows that the shaver is charging (see chapter ‘The

display’).

3 RQ1008: Press the up/down button to select a cleaning program.

ENGLISH 17

4 Press the on/off button on the Jet Clean System to start the cleaning

program.

, The shaver display stops showing the charging indication.

, The cleaning light starts to ash and the shaver is automatically

lowered into the cleaning uid.

, The cleaning light ashes throughout the cleaning program, which

takes a few minutes.

Note: RQ1007: The cleaning program takes 4 to 6 minutes.

Note: RQ1008: The auto and eco cleaning programs take 4 to 6 minutes. The

intensive program takes approx. 35 minutes.

, During the rst phase of the cleaning program, the shaver

automatically switches on and off several times and moves up and

down.

, During the second phase of the cleaning program, the shaver is

placed in the drying position, indicated by the ashing drying symbol.

This phase takes approx. 2 hours. The shaver stays in this position

until the end of the program.

Note: RQ1008: The drying phase takes 1 hour when you have selected the eco

program.

, After the cleaning program, the charging indication appears on the

shaver display (see chapter ‘The display’).

Note: If you press the on/off button of the Jet Clean System during the cleaning

program, the program aborts. In this case, the cleaning or drying light stops

ashing and the holder moves to the highest position.

Note: If you remove the adapter from the wall socket during the cleaning

program, the program aborts. The holder remains in its current position. When

you put the adapter back into the wall socket, the holder moves to the highest

position.

- When the cleaning uid drops below the minimum level, the ‘cleaning

chamber empty’ symbol starts to ash and the holder returns to its

starting position.

- If you use the Jet Clean System to clean your shaver every day, you

need to rell the cleaning chamber approx. every 15 days.

Cleaning the Jet Clean System

Clean the cleaning chamber every 15 days.

You can wipe the outside of the Jet Clean System with a damp cloth.

ENGLISH18

1 Simultaneously press the release buttons on both sides of the Jet

Clean System (1). Then lift the Jet Clean System off the cleaning

chamber (2).

, The cleaning chamber remains behind.

2 Pour any remaining cleaning uid out of the cleaning chamber.

You can simply pour the cleaning uid down the sink.

3 Rinse the cleaning chamber under the tap.

The cleaning chamber is not dishwasher-proof.

4 Fill the cleaning chamber with HQ200 cleaning uid to a level

between the two lines.

5 Place the Jet Clean System back onto the cleaning chamber.

Make sure the release buttons click back into place.

ENGLISH 19

Extra-thorough cleaning method

Make sure the appliance is switched off.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the shaver.

2 Pull open the three shaving heads one by one.

3 Press the retainer release tab (1) until the retainer opens (2).

Note: Do not clean more than one cutter and shaving guard at a time, since

they are all matching sets. If you accidentally put a cutter in the wrong shaving

guard, it may take several weeks before optimal shaving performance is

restored.

4 Remove the cutter from the shaving guard.

5 Clean the cutter with the cleaning brush supplied.

ENGLISH20

Leht laadib ...

Philips RQ1285/16 Kasutusjuhend

Philips RQ1285/16 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid