Samsung HW-R440 Kasutusjuhend

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

HW-R440

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code. To see the manual on

your PC or mobile device, download the

manual in document format from Samsung’s

website. (http://www.samsung.com/support)

Design and specications are subject to change

without prior notice.

ENG - iv

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Right Side Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar ------------------------- 4

03 Connecting the Soundbar 5

Connecting Electrical Power

-------------------------

5

Connecting the Soundbar to the Subwoofer

-------------------------

6

– Automatic connection between the Subwoofer and the Soundbar

-------------------------

6

– Manually connecting the Subwoofer if automatic connection fails

-------------------------

7

Connecting an SWA-8500S (Sold Separately) to your Soundbar

-------------------------

8

04 Connecting to your TV 10

Method 1. Connecting with a Cable

-------------------------

10

– Connecting using an Optical Cable

-------------------------

10

Method 2. Connecting Wirelessly

-------------------------

11

– Connecting a TV via Bluetooth

-------------------------

11

05 Connecting an External Device 13

Connecting using an Optical or Analogue Audio (AUX) Cable

-------------------------

13

06 Connecting a USB Storage Device 14

ENG - v

07 Connecting a Mobile Device 16

Connecting via Bluetooth

-------------------------

16

Using the Samsung Audio Remote App

-------------------------

19

– Installing the Samsung Audio Remote App

-------------------------

19

– Launching the Samsung Audio Remote App

-------------------------

19

08 Using the Remote Control 20

How to Use the Remote Control

-------------------------

20

Adjusting the Soundbar volume with a TV remote control

-------------------------

23

Using the Hidden Buttons (Buttons with more than one function)

-------------------------

24

Output specications for the different sound effect modes

-------------------------

24

09 Installing the Wall Mount 25

Installation Precautions

-------------------------

25

Wallmount Components

-------------------------

25

Detaching the Soundbar from the Wall

-------------------------

27

10 Software Update 28

Updating Procedure

-------------------------

28

If UPDATE is not displayed

-------------------------

29

11 Troubleshooting 30

12 Licence 31

13 Open Source Licence Notice 31

14 Important Notes About Service 31

15 SpecicationsandGuide 32

Specications

-------------------------

32

ENG - 2

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Subwoofer Remote Control /

Batteries

Optical Cable

1 3

Power Cord (Subwoofer) AC/DC Adapter

(Main Unit)

Wall Mount Guide

2

Connect the AC plug to the adapter until you hear

a “snapping” sound to ensure they are securely

fastened.

AC Plug

(Depending on the country and

model)

Do not detach the AC plug from the adapter (it will

not be removed once it has been attached).

x 2

Holder-Screw Screw Bracket-Wall Mount L Bracket-Wall Mount R

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• The power components are labelled (1, 2, 3). For more information about power connections,

see page 5.

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• Depending on the region, the appearance of the AC plug may differ from the plug displayed above,

or it may be supplied integrated with the AC/DC adapter.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the battery cover back into position.

ENG - 3

02 PRODUCT OVERVIEW

Front Panel / Right Side Panel of the Soundbar

󰟴

󰟳

󰟵 󰟶

Right Side of the Soundbar

Position the product so that the

SAMSUNG logo is located on the top.

󰟳

Display

Displays the product’s status and current mode.

󰟴

+/- (Volume) Button

Adjusts the volume.

• When adjusted, the volume level appears on the Soundbar’s front display.

󰟵

(Power) Button

Turns the power on and off.

󰟶

(Source) Button

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

AUX input AUX

BLUETOOTH mode BT

USB mode USB

• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the

(Source) button for more than 5 seconds.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio

Setup menu of your TV. Refer to the owner’s manual supplied with your TV.

ENG - 4

Bottom Panel of the Soundbar

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

AUX IN

DC 19V

󰟳

󰟶

󰟴

󰟵

󰟳

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

󰟴

USB (5V 0.5A)

Connect a USB device here to play music les on the USB device through the Soundbar.

󰟵

AUX IN

Connect to the Analogue output of an external device.

󰟶

DC 19V (Power Supply In)

Connect the AC/DC power adapter.

• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 5

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2

, 3

) to connect the Subwoofer and Soundbar to an electrical outlet in

the following order:

1 Connect the power cord to the Subwoofer.

2 Connect the AC plug to the adapter.

3

Connect the power adapter to the Soundbar and then to a wall socket.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

POWER

Rear of Subwoofer

1 Power Cord

Connecting

Electrical Power

DC 19V

Bottom of the

Soundbar Main Unit

DC 19V

(Power Jack)

3 AC/DC Adapter

2 AC Plug

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

ENG - 6

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.

Automatic connection between the Subwoofer and the Soundbar

When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the

subwoofer is automatically connected to the Soundbar.

• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Blue

On

Successfully connected

(normal operation)

-

Blinking Recovering the connection

Check if the power cable attached to the

main Soundbar unit is connected properly

or wait about 5 minutes. If blinking persists,

try manually connecting the subwoofer.

See page 7.

Red On

Standby (with the Soundbar

main unit turned off)

Check if the power cable attached to the

main Soundbar unit is connected properly.

Connection failed

Connect again. See the instructions for

manual connection on page 7.

Red and

blue

Blinking Malfunction

See the contact information for the

Samsung Service Centre in this manual.

ENG - 7

Manually connecting the Subwoofer if automatic connection fails

Before performing the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

2. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

SOUND

MODE

PAIR

5 Sec

ID SET

3. Check if the LINK LED is solid blue (connection complete).

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Subwoofer.

ENG - 8

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections

between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the

STANDBY LED on the rear will turn red after blinking in blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may

vary depending on your operating environment. If a steel-concrete or metallic wall is between the

main unit and the wireless subwoofer, the system may not operate at all because the wireless

signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water

and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the

Wireless Receiver Module (sold separately) is clear of any obstructions.

Connecting an SWA-8500S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-8500S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– The speaker cables are colour coded.

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

ENG - 9

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not

blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for

5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer

to the SWA-8500S user manual.

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

STANDBY

LINK

STANDBY

LINK

Blue blinking

5 Sec

3. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

SOUND

MODE

PAIR

5 Sec

ID SET

CAUTION

• If your Soundbar was playing music when it connects to the SWA-8500S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete).

STANDBY

LINK

STANDBY

LINK

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Receiver Module.

5. If the SWA-8500S is not connected, repeat the procedure from Step 2.

ENG - 10

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using

the TV’s remote control.

– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when

you connect the Soundbar to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on

the TV is changed, you will experience better sound quality. (The TV menu may use different words for

Dolby Digital and PCM depending on the TV manufacturer.)

Connecting using an Optical Cable

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

AUX IN

OPTICAL OUT

Optical Cable

Bottom of the Soundbar

D.IN

󰟳

󰟴

Right Side of the Soundbar

1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV

with a digital optical cable.

2. Press the (Source) button on the right side panel or remote control, and then select the “D.IN”

mode.

ENG - 11

Auto Power Link

Auto Power Link automatically turns on the Soundbar when the TV is turned on.

1. Connect the Soundbar and a TV with a digital optical cable.

2. Press the Left button on the remote control for 5 seconds to turn Auto Power

Link on or off.

• Auto Power Link is set to ON by default.

(To turn off this function, hold the Left button on the remote for 5 seconds.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

SOUND

MODE

PAIR

OR

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the right side panel and then select “BT”.

“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device

connected to the Soundbar.

b. When “BT READY” appears, press and hold the (Source) button on the right side panel

of the Soundbar for more than 5 seconds to display “BT PAIRING”.

2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

3. Select “[AV] Samsung Soundbar R4-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device

list. To connect the TV to the Soundbar, select the message, and then establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

4. You can now hear TV sound from the Soundbar.

ENG - 12

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar R4-Series”) appears in

the list, delete it.

• Then repeat steps 1 through 3.

NOTE

• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to

reconnect.

Disconnecting the Soundbar from the TV

Press the (Source) button on the right side panel or on the remote control and switch to any mode

but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.

(The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the

p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status.

(Toggle On → Off)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously

connected mobile device to the Soundbar.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button

on the remote control or press and hold the (Source) button on the right side of the Soundbar

for more than 5 seconds while the Soundbar is in “BT” mode.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the

Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 13

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound

through the Soundbar.

Connecting using an Optical or Analogue Audio (AUX) Cable

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

AUX IN

OPTICAL OUT

- AUDIO -

R L

Optical Cable

Audio (AUX) Cable

(not supplied)

Bottom of the Soundbar

󰟳

󰟴

BD / DVD player / Set-top box /

Game console

Right Side of the Soundbar

1 Optical Cable

X Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source

Device using a digital optical cable.

Y Select “D.IN” mode by pressing the (Source) button on the right side panel or on the remote

control.

2 Audio (AUX) Cable

X Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an

audio cable.

Y Select “AUX” mode by pressing the (Source) button on the right side panel or on the remote

control.

ENG - 14

06 CONNECTING A USB STORAGE DEVICE

You can play music les located on USB storage devices through the Soundbar.

Display

USB port

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

DC 19V

USB (5V 0.5A)

Micro USB to

USB adapter Cable

(not supplied)

USB

1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one

end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your

Soundbar.

• The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service

Centre or Samsung Customer Care.

2. Connect your USB device to the female end of the adapter cable.

3. Press the (Source) button on the right side panel or on the remote control, and then select

“USB”.

4. “USB” appears in the display screen.

5. Play music les from the USB storage device through the Soundbar.

• The Soundbar automatically turns off (Auto Power Down) if no USB device has been connected

for more than 20 minutes.

ENG - 15

File Format Type Compatibility list

Extension Codec Sampling Rate Bitrate

*.mp3 MPEG 1 Layer2 16kHz ~ 48kHz 80kbps~320kbps

MPEG 1 Layer3 16kHz ~ 48kHz 80kbps~320kbps

MPEG 2 Layer3 16kHz ~ 48kHz 80kbps~320kbps

MPEG 2.5 Layer3 16kHz ~ 48kHz 80kbps~320kbps

*.wma Wave_Format_MSAudio1 16kHz ~ 48kHz 56kbps~128kbps

Wave_Format_MSAudio2 16kHz ~ 48kHz 56kbps~128kbps

*.aac AAC 16kHz ~ 96kHz 48kbps~320kbps

A AC- LC 16kHz ~ 96kHz

128kbps~192kbps

5.1ch 320kbps

HE-AAC 24kHz ~ 96kHz

48kbps~64kbps

5.1ch 160kbps

*.wav - 16kHz ~ 48kHz up to 3000kbps

*.ogg OGG 1.1.0 16kHz ~ 48kHz 50kbps~500kbps

• If there are too many folders and les stored on the USB device, it may take the Soundbar some

time to access and play les.

ENG - 16

07 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of

cabling.

• You cannot connect more than one Bluetooth device at a time.

SOUND

MODE

PAIR

OR

Bluetooth device

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the right side panel and then select “BT”.

“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device

connected to the Soundbar.

b. When “BT READY” appears, press and hold the (Source) button on the right side panel

of the Soundbar for more than 5 seconds to display “BT PAIRING”.

2. On your device, select “[AV] Samsung Soundbar R4-Series” from the list that appears.

• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”

appears in the front display.

3. Play music les from the device connected via Bluetooth through the Soundbar.

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar R4-Series”) appears in

the list, delete it.

• Then repeat steps 1 and 2.

NOTE

• After you have connected the Soundbar to your mobile device the rst time, use the “BT READY”

mode to reconnect.

Leht laadib ...

Samsung HW-R440 Kasutusjuhend

Samsung HW-R440 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid