Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

Kaubamärk: Jacobsen

Mudel: 67955, 67956, 67957, 68007, 68008

Kategooria: Muruniidukid

Tüüp: Omaniku manuaal

See juhend sobib ka

Safety, Operation, & Maintenance Manual

WARNING

Warning: If incorrectly used, this machine can

cause severe injury. Those who use and maintain

this machine should be trained in its proper use,

warned of its dangers, and must read the entire

manual before attempting to set up, operate, adjust,

or service the machine.

Super LF 1880™ Fairway Mower with ROPS

67955 – Kubota D1105-E3B, 2WD

67956 – Kubota D1105-E3B, 4WD

67957 – Kubota D1105-T-E3B, 4WD

68007 – Kubota D1105-E4B, 2WD

68008 – Kubota D1105-E4B, 4WD

4160165-Rev B

This manual contains safety and operating instructions

for your new Jacobsen machine. This manual should be

stored with the equipment for reference during operation.

Before you operate your machine, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating, and

maintenance instructions, you will prolong the life of your

equipment, and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

The serial plate is located on the left rear frame rail.

Jacobsen recommends you record these numbers below

for easy reference.

CHARLOTTE, NC

YEAR OF

PRODUCTION:

MADE IN U.S.A.

A Textron Company

FOREWORD

1 CONTENTS

right to reproduce this material or portions thereof in any form.”

Proposition 65 Warning

This product contains or emits

chemicals known to the State of

California to cause cancer and birth

defects or other reproductive harm.

Litho In U.S.A. 2-2014

CONTENTS 1

1CONTENTS

2SAFETY

2.1 Operating Safety .................................................. 4

2.2 Important Safety Notes .........................................5

3 SPECIFICATIONS

3.1 Product Identification............................................ 6

3.2 Kubota D1105-E Engine .......................................6

3.3 Kubota D1105-TE Engine ....................................6

3.4 Cutting Units .........................................................7

3.5 Mower ...................................................................7

3.6 Weights and Dimensions ......................................7

3.7 Accessories & Support Literature .........................7

3.8 Declaration of Conformity .....................................8

4DECALS

4.1 Decals ................................................................ 10

5 CONTROLS

5.1 Icons................................................................... 13

5.2 Control Descriptions ...........................................15

5.3 Operator Alerts ...................................................17

6 OPERATION

6.1 Daily Inspection .................................................. 18

6.2 Interlock System .................................................18

6.3 Operating Procedures ........................................19

6.4 Starting ...............................................................20

6.5 Stopping / Parking ..............................................20

6.6 To Drive / Transport ...........................................21

6.7 Hillside Operation ...............................................21

6.8 Mowing ...............................................................22

6.9 Towing / Trailering ..............................................22

6.10 Daily Maintenance ..............................................23

7 MAINTENANCE & LUBRICATION CHARTS

7.1 General............................................................... 24

7.2 Lubrication Chart ................................................24

7.3 Maintenance Charts ...........................................25

8 MAINTENANCE

8.1 General............................................................... 26

8.2 Engine ................................................................26

8.3 Engine Oil ...........................................................26

8.4 Air Filter ..............................................................27

8.5 Fuel ....................................................................27

8.6 Fuel System .......................................................27

8.7 Battery ................................................................28

8.8 Jump Starting .....................................................28

8.9 Charging Battery ................................................28

8.10 Hydraulic Hoses .................................................29

8.11 Hydraulic Oil and Filters .....................................29

8.12 Electrical System ................................................30

8.13 Muffler and Exhaust ...........................................31

8.14 Tires ...................................................................31

8.15 Wheel Mounting Procedure ................................31

8.16 Roll Over Protective Structure (ROPS) ..............31

8.17 Care and Cleaning .............................................32

8.18 Radiator ..............................................................32

8.19 Backlapping ........................................................33

8.20 Storage ...............................................................34

9 ADJUSTMENTS

9.1 General.............................................................. 35

9.2 Engine Belt ........................................................ 35

9.3 Throttle .............................................................. 35

9.4 Neutral Switch and 4WD Cut-Out Switch .......... 36

9.5 Transport Speed ................................................ 36

9.6 Traction Pedal Speed Limiter ............................ 37

9.7 Parking Brake .................................................... 37

9.8 Brake Switch ...................................................... 37

9.9 Steering Adjustments ........................................ 38

9.10 Lift Limit Switch .................................................. 38

9.11 Bedknife-To-Reel ............................................... 39

9.12 Bedknife Adjustment .......................................... 40

9.13 Cutting Height .................................................... 40

9.14 Reel Bearing ...................................................... 41

9.15 Bedknife Adjuster Spring ................................... 41

9.16 Bedknife Adjuster Tension ................................. 41

9.17 Grinding Bedknife .............................................. 41

9.18 Flash Attach ....................................................... 42

9.19 Down Pressure .................................................. 42

9.20 Torque Specification .......................................... 43

9.21 Specific Torque .................................................. 43

10 PROBLEM SOLVING

10.1 General Problem Solving................................... 44

11 QUALITY OF CUT

11.1 Quality of Cut Problem Solving.......................... 45

11.2 Washboarding ................................................... 45

11.3 Marcelling .......................................................... 46

11.4 Step Cutting ....................................................... 47

11.5 Scalping ............................................................. 48

11.6 Stragglers .......................................................... 49

11.7 Streaks .............................................................. 50

11.8 Windrowing ........................................................ 51

11.9 Rifling Or Tramlining .......................................... 52

11.10 Mismatched Cutting Units .................................. 52

12 NOTES

2 SAFETY

2.1 OPERATING SAFETY ______________________________________________________

1. Safety is dependent upon the awareness, concern,

and prudence of those who operate or service the

equipment. Never allow minors to operate any

equipment.

2. It is your responsibility to read this manual and all

publications associated with this equipment (Parts

and Maintenance Manual, Engine Manual, and

attachments/accessories instruction sheets). If the

operator cannot read English it is the owner’s

responsibility to explain the material contained in

this manual to them.

3. Learn the proper use of the machine, the location and

purpose of all the controls and gauges, before you

operate the equipment. Working with unfamiliar

equipment can lead to accidents.

4. Never allow anyone to operate or service the machine

or its attachments without proper training and

instructions; or while under the influence of alcohol or

drugs.

5. Wear all the necessary protective clothing and

personal safety devices to protect your head, eyes,

ears, hands, and feet. Operate the machine only in

daylight or in good artificial light.

6. Evaluate the terrain to determine what accessories and

attachments are needed to properly and safely perform

the job. Only use accessories and attachments

approved by Jacobsen.

7. Stay alert for holes in the terrain and other hidden

hazards.

8. Inspect the area where the equipment will be used.

Pick up all the debris you can find before operating.

Beware of overhead obstructions (low tree limbs,

electrical wires, etc.) and also underground obstacles

(sprinklers, pipes, tree roots, etc.). Enter a new area

cautiously. Stay alert for hidden hazards.

9. Never direct discharge of material toward bystanders,

nor allow anyone near the machine while in operation.

The owner/operator can prevent and is responsible for

injuries inflicted to themselves, to bystanders, and

damage to property.

10. Do not carry passengers. Keep bystanders and pets a

safe distance away.

11. Never operate equipment that is not in perfect working

order or is without decals, guards, shields, discharge

deflectors, or other protective devices securely

fastened in place.

12. Never disconnect or bypass any switch.

13. Do not change the engine governor setting or

overspeed the engine.

14. Carbon monoxide in the exhaust fumes can be fatal

when inhaled. Never operate the engine without proper

ventilation or in an enclosed area.

15. Fuel is highly flammable; handle with care.

16. Keep the engine clean. Allow the engine to cool before

storing and always remove the ignition key.

17. Disengage all drives and engage parking brake before

starting the engine (motor). Start the engine only when

sitting in operator’s seat, never while standing beside

the unit.

18. Equipment must comply with the latest federal, state,

and local requirements when driven or transported on

public roads. Watch out for traffic when crossing or

operating on or near roads.

19. Local regulations may restrict the age of the operator.

20. Operate the machine up and down the face of slopes

(vertically), not across the face (horizontally).

21. To prevent tipping or loss of control, do not start or

stop suddenly on slopes. Reduce speed when making

sharp turns. Use caution when changing directions.

22. Always use the seat belt when operating mowers

equipped with a Roll Over Protective Structure

(ROPS).

Never use a seat belt when operating mowers

without a ROPS.

Accessory operator protective structures will

continue to be offered for all equipment currently

covered. This allows for the outfitting of any

machines without previous ROPS installations or

replacement of damaged structures.

23. Keep legs, arms and body inside the seating

compartment while the vehicle is in motion.

This machine is to be operated and maintained as specified in this manual and is intended for the professional

maintenance of specialized turf grasses. It is not intended for use on rough terrain or long grasses.

WARNING

EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.

Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive

instruction from someone familiar with the equipment before being allowed to operate the machine.

SAFETY 2

2.2 IMPORTANT SAFETY NOTES ________________________________________________

This safety alert symbol is used to alert you to potential hazards.

DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious

injury.

CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury

and property damage. It may also be used to alert against unsafe practices.

NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may

also be used to alert against unsafe practices.

For pictorial clarity, some illustrations in this manual may show shields, guards, or plates open or removed. Under no

circumstances should this equipment be operated without these devices securely fastened in place.

By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum

efficiency. Adjustments and maintenance should always be performed by a qualified technician.

If additional information or service is needed, contact your Authorized Jacobsen Dealer, who is kept informed of the

latest methods to service this equipment, and can provide prompt and efficient service. Use of other than original or

authorized Jacobsen parts and accessories will void the warranty.

WARNING

The Interlock System on this mower prevents the mower from starting unless

the brake lever is engaged, mower switch is off, and traction pedal is in

neutral. The system will stop the engine if the operator leaves the seat

without engaging the parking brake or setting the mower switch off.

NEVER operate mower unless the Interlock System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction pedal to neutral.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop engine and remove the ignition key.

2. Keep hands, feet, and clothing away from moving parts. Wait for all

movement to stop before you clean, adjust, or service the machine.

3. Keep the area of operation clear of all bystanders and pets.

4. Never carry passengers, unless a seat is provided for them.

5. Never operate mowing equipment without the discharge deflector

securely fastened in place.

3 SPECIFICATIONS

3 SPECIFICATION S

3.1 PRODUCT IDENTIFICATION _________________________________________________

67955.............................. Super LF 1880 2WD with ROPS

67956.............................. Super LF 1880 4WD with ROPS

67957.............................. Super LF 1880 Turbo 4WD with

ROPS

68007.............................. Super LF 1880 2WD with ROPS

68008.............................. Super LF 1880 4WD with ROPS

Serial Number ................ An identification plate, like the one

shown, listing the serial number, is

attached to theleft rear frame of

rail of the mower.

Always provide the serial number of the unit when ordering

replacement parts or requesting service information.

3.2 KUBOTA D1105-E ENGINE __________________________________________________

Make ............................... Kubota

Model .............................. D1105-E3B (67955 and 67956)

Model .............................. D1105-E4B (68007 and 68008)

Horsepower..................... 24.8 hp (18.5 kW) @3000 RPM

Note: Actual sustained horsepower will likely be lower

than listed in specifications due to operating limitations

and environmental factors.

Displacement .................. 68.5 cu. In. (1123 cc)

Torque............................. 52.7 ft lbs. (71.5 Nm) @ 2200

RPM

Fuel:

Type .......................... No. 2 Low or Ultra Low Sulfur

Diesel

Rating ....................... Cetane Rating-45

Capacity.................... 12 U.S. Gal. (45.4 liters)

High speed - rpm............ 3150 no load

Low Idle - rpm................. 1750 no load

Lubrication:

Capacity.................... 5.4 qt (5.1 liters)

Type .......................... SAE 10W30

API Classification ..... CD,CE

Air Filter .......................... Dry type with service indicator

Alternator ........................ 40 amp

Cooling System .............. Liquid Cooled

3.3 KUBOTA D1105-TE ENGINE _________________________________________________

Make ............................... Kubota

Model .............................. D1105-T-E3B (67957)

Horsepower..................... 32.9 hp (24.5 kW) @3000 RPM

Note: Actual sustained horsepower will likely be lower

than listed in specifications due to operating limitations

and environmental factors.

Displacement .................. 68.5 cu. In. (1123 cc)

Torque............................. 65 ft. lbs. (88.1 Nm) @ 2200 RPM

Fuel:

Type .......................... No. 2 Low or Ultra Low Sulfur

Diesel

Rating ....................... Cetane Rating-45

Capacity.................... 12 U.S. gal. (45.4 liters)

High speed - rpm ............ 3150 no load

Low Idle - rpm ................. 1750 no load

Lubrication:

Capacity.................... 5.4 qt. (5.1 liters)

Type .......................... SAE 10W30

API Classification ..... CD,CE

Air Filter .......................... Dry type with service indicator

Alternator ........................ 40 amp

Cooling System .............. Liquid Cooled

Product

EEC Sound

Power

Vibration M/S

Arms Body

67955

67956

67957

68007

68008

<105 dba

3.578

2.758

0.0246

0.0318

11524 WILMAR BLVD,

CHARLOTTE, NC 28273

kg kW

1-800-848-1636 (US)

PRODUCT OF U.S.A.

A Textron Company

849.1 18.5 XXXX

67955001651

SPECIFICATIONS 3

3.4 CUTTING UNITS ___________________________________________________________

Reel.................................5 Reels, 18 in. (457 mm) wide

Reel Diameter .................5 in. (127 mm)

Blade Options .................8 or 11 blades

Cutting Height .................0.30 to 0.70 in. (7.6 to 18 mm)

Cutting Width .................. 82 in. (2032 mm)

Cutting Frequency:

8 Blade...................... 0.067 in./mph (1.06 mm/kph)

11 Blade.................... 0.049 in./mph (0.77 mm/kph)

3.5 MOWER__________________________________________________________________

Tires

Front.......................... 24 x 13-12 2 Ply

Rear ..........................18 x 9.5-8 2 Ply

Pressure:.........................10-12 psi (0.69 - 0.83 BAR)

Battery:

Type ..........................12 Volt Lead/Acid

Group ........................ 45 GMF

Speed:

Mow (4 WD) ..............0 - 6 mph (9.6 kph)

Transport (2 WD)....... 0 - 10.5 mph (16.9 kph)

Reverse..................... 0 - 4 mph (6.4 kph)

Parking Brake ................. Mechanical front wheel disc

Hydraulic System:

Capacity.......................... 8 U.S. gal. (30.28 liters) System

Fluid Type ....................... GreensCare™ 68

Return Filter.................... Full Flow 10 micron

Charge Filter................... Full Flow 10 micron

Steering ......................... Hydrostatic Power Steering

Mower Lift ....................... Hydraulic Double Acting Cylinders

3.6 WEIGHTS AND DIMENSIONS ________________________________________________

Dimensions: Inches (mm)

Length - Grass Catchers On ......................... 106 (2692)

Height - Top of Steering Wheel ....................... 56 (1422)

Wheel Base.................................................. 59.1 (1501)

Width - Transport Position ............................ 88.5 (2248)

Width - Mowing Position............................... 88.5 (2248)

Width - Wheel ............................................ 74.25 (1886)

Turning Radius ................................................ 18 (457)

Weights: Lbs. (kg)

Working Weight Less Operator

67955 .......................................................... 2205 (1000)

67956 .......................................................... 2280 (1034)

67957 .......................................................... 2330 (1057)

68007 .......................................................... 2205 (1000)

68008 .......................................................... 2280 (1034)

3.7 ACCESSORIES & SUPPORT LITERATURE _____________________________________

Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.

Accessories

Air Blow Gun ...........................................................JAC5098

Orange Touch-up Paint (12 oz. spray) ...................... 554598

Arm Rest ................................................................. 4139431

Grass Catcher............................................................. 67930

Powered Rear Roller Cleaner Brush ........................... 67929

Turf Groomer 1/2 in. Spacing ...................................... 67926

2 Post ROPS............................................................... 66194

Canopy (Requires 2 Post ROPS)................................ 68095

4WD Field Conversion Kit ........................................... 67931

Vertical Mower Lift Yoke Kit......................................... 67934

High Cut Roller Kit 15/16 in......................................... 68634

Vertical Mower ............................................................ 67928

MAGSystem™ Kit ................................................... 4161022

Reels

8 Blade Reel ................................................................62837

11 Blade Reel ..............................................................62838

Rollers

3 in. dia. Grooved Front Roller with Scraper................67925

2-3/16 in. Solid Front Roller with Scraper ....................68626

2-3/16 in. Grooved Front Roller ...................................68616

2-3/16 in. Full Width Solid Rear Roller with Scraper....68674

Support Literature

Safety & Operation Manual......................................4160165

Parts & Maintenance Manual...................................4160164

Diesel Engine Parts Catalog....................................4160162

Operator Training Video...........................................4102141

Service & Repair Manual.........................................4171721

CAUTION

Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the

equipment.

3 SPECIFICATIONS

3.8 DECLARATION OF CONFORMITY ____________________________________________

DECLARATION OF CONFORMITY ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ PROHLÁŠENÍ O SHODĚ ▪

OVERENSSTEMMELSESERKLÆRING ▪ CONFORMITEITSVERKLARING ▪ VASTAVUSDEKLARATSIOON ▪

VAATIMUSTENMUKAISUUSVAKUUTUS ▪ DECLARATION DE CONFORMITE ▪ KONFORMITÄTSERKLÄRUNG ▪

∆ΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ▪ MEGFELELŐSÉGI NYILATKOZAT ▪ DICHIARAZIONE DI CONFORMITÀ ▪ ATBILSTĪBAS

DEKLARĀCIJA ▪ ATITIKTIES DEKLARACIJA ▪ DIKJARAZZJONI TAL-KONFORMITÀ ▪ DEKLARACJA ZGODNOŚCI ▪

DECLARAÇÃO DE CONFORMIDADE ▪ DECLARAŢIE DE CONFORMITATE ▪ VYHLÁSENIE O ZHODE ▪ IZJAVA O

SKLADNOSTI ▪ DECLARACIÓN DE CONFORMIDAD ▪ DEKLARATION OM ÖVERENSSTÄMMELSE

Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa výrobce ▪

Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪

Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des Herstellers ▪

Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo completo del fabbricante ▪

Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem kummerċjali u indirizz sħiħ tal-fabbrikant ▪

Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪ Denumirea comercială şi adresa completă a

producătorului ▪ Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov proizvajalca ▪ Nombre de la empresa y dirección completa del

fabricante ▪ Tillverkarens företagsnamn och kompletta adress

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

Product Code ▪ Код

на продукта ▪ Kód výrobku ▪ Produktkode ▪ Productcode ▪ Toote kood ▪ Tuotekoodi ▪ Code produit ▪ Produktcode ▪ Κωδικός προϊόντος

▪ Termékkód ▪ Codice prodotto ▪ Produkta kods ▪ Produkto kodas ▪ Kodiċi tal-Prodott ▪ Kod produktu ▪ Código do Produto ▪ Cod produs ▪ Kód výrobku ▪

Oznaka proizvoda ▪ Código de producto ▪ Produktkod

67955

67956

67957

68007

68008

Machine Name ▪ Наименование на машината ▪ Název stroje ▪ Maskinnavn ▪ Machinenaam ▪ Masina nimi ▪ Laitteen nimi ▪ Nom de la machine ▪

Maschinenbezeichnung ▪ Ονομασία μηχανήματος ▪ Gépnév ▪ Denominazione della macchina ▪ Iekārtas nosaukums ▪ Mašinos pavadinimas ▪ Isem tal-

Magna ▪ Nazwa urządzenia ▪

Nome da Máquina ▪ Numele echipamentului ▪ Názov stroja ▪ Naziv stroja ▪ Nombre de la máquina ▪ Maskinens namn

SLF 1880 2WD

SLF 1880 4WD

SLF 1880 4WD Turbo

SLF 1880 2WD

SLF 1880 4WD

Designation ▪ Предназначение ▪ Označení ▪ Betegnelse ▪ Benaming ▪ Nimetus ▪ Tyyppimerkintä ▪ Pažymėjimas ▪ Bezeichnung ▪ Χαρακτηρισμός ▪

Megnevezés ▪ Funzione ▪ Apzīmējums ▪ Lithuanian ▪ Denominazzjoni ▪ Oznaczenie ▪ Designação ▪ Specificaţie ▪ Označenie ▪ Namen stroja ▪ Descripción

▪ Beteckning

Lawnmower, Article 12, Item 32

Serial Number ▪ Сериен номер ▪ Sériové číslo ▪ Serienummer ▪ Serienummer ▪ Seerianumber ▪ Valmistusnumero ▪ Numéro de série ▪ Seriennummer ▪

Σειριακός

αριθμός ▪ Sorozatszám ▪ Numero di serie ▪ Sērijas numurs ▪ Serijos numeris ▪ Numru Serjali ▪ Numer seryjny ▪ Número de Série ▪ Număr de

serie ▪ Sériové číslo ▪ Serijska številka ▪ Número de serie ▪ Serienummer

6795501651-6795502500

6800701651-6800702500

6800801651-6800802500

Engine ▪ Двигател ▪ Motor ▪ Motor ▪ Motor ▪ Mootor ▪ Moottori ▪ Moteur ▪ Motor ▪ Μηχανή ▪ Modulnév ▪ Motore ▪ Dzinējs ▪ Variklis ▪ Saħħa Netta Installata ▪

Silnik ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor

Kubota D1105-E3B Diesel

Kubota D1105-T-E3B Diesel

Kubota D1105-E3B Diesel

Net Installed Power ▪ Нетна инсталирана мощност ▪

Čistý instalovaný výkon ▪ Installeret nettoeffekt ▪ Netto geïnstalleerd vermogen ▪ Installeeritud

netovõimsus ▪ Asennettu nettoteho ▪ Puissance nominale nette ▪ Installierte Nettoleistung ▪ Καθαρή εγκατεστημένη ισχύς ▪ Nettó beépített teljesítmény ▪

Potenza netta installata ▪ Paredzētā tīkla jauda ▪ Grynoji galia ▪ Wisa’ tal-Qtugħ ▪ Moc zainstalowana netto ▪ Potência instalada ▪ Puterea instalată netă ▪

Čistý inštalovaný výkon ▪ Neto vgrajena moč ▪ Potencia instalada neta ▪ Nettoeffekt

18,5 kW @ 3000 RPM

24,5 kW @ 3000 RPM

18,5 kW @ 3000 RPM

Cutting Width ▪ Широчина на рязане ▪ Šířka řezu ▪ Skærebredde ▪ Maaibreedte ▪ Lõikelaius ▪ Leikkuuleveys ▪ Largeur de coupe ▪ Schnittbreite ▪

Μήκος μισινέζας ▪

Vágási szélesség ▪ Larghezza di taglio ▪ Griešanas platums ▪ Pjovimo plotis ▪ Tikkonforma mad-Direttivi ▪ Szerokość cięcia ▪

Largura de Corte ▪ Lăţimea de tăiere ▪ Šírka záberu ▪ Širina reza ▪ Anchura de corte ▪ Klippbredd

203 cm

Conforms to Directives ▪ В съответствие с директивите ▪ Splňuje podmínky směrnic ▪ Er i overensstemmelse med direktiver ▪ Voldoet aan de richtlijnen ▪

Vastab direktiividele ▪ Direktiivien mukainen ▪ Conforme aux directives ▪ Entspricht Richtlinien ▪ Ακολουθήστε πιστά τις Οδηγίες ▪ Megfelel az irányelveknek

▪ Conforme alle Direttive ▪ Atbilst direktīvām ▪ Atitinka direktyvų reikalavimus ▪ Valutazzjoni tal-Konformità ▪ Dyrektywy związane ▪ Cumpre as Directivas ▪

Respectă Directivele ▪

Je v súlade so smernicami ▪ Skladnost z direktivami ▪ Cumple con las Directivas ▪ Uppfyller direktiv

2004/108/EC

2006/42/EC

2000/14/EC, 2005/88/EC

2006/66/EC

Conformity Assessment ▪ Оценка за съответствие ▪ Hodnocení plnění podmínek ▪ Overensstemmelsesvurdering ▪ Conformiteitsbeoordeling ▪

Vastavushindamine ▪ Vaatimustenmukaisuuden arviointi ▪ Evaluation de conformité ▪ Konformitätsbeurteilung ▪ ∆ιαπίστωση Συμμόρφωσης ▪

Megfelelőség-értékelés ▪ Valutazione della conformità ▪ Atbilstības novērtējums ▪ Atitikties įvertinimas ▪ Livell tal-Qawwa tal-Ħoss Imkejjel ▪ Ocena

zgodności ▪ Avaliação de Conformidade ▪ Evaluarea conformităţii ▪ Vyhodnotenie zhodnosti ▪ Ocena skladnosti ▪ Evaluación de conformidad ▪

Bedömning av överensstämmelse

2006/42/EC Annex VIII

Measured Sound Power Level ▪ Измерено ниво на звукова мощност ▪ Naměř

ený akustický výkon ▪ Målte lydstyrkeniveau ▪ Gemeten geluidsniveau ▪

Mõõdetud helivõimsuse tase ▪ Mitattu äänitehotaso ▪ Niveau de puissance sonore mesuré ▪ Gemessener Schalldruckpegel ▪

Σταθμισμένο επίπεδο ηχητικής ισχύος ▪ Mért hangteljesítményszint ▪ Livello di potenza sonora misurato ▪ Izmērītais skaņas jaudas līmenis ▪

Išmatuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna mierzona ▪ Nível sonoro medido ▪ Nivelul măsurat al puterii

acustice ▪ Nameraná hladina akustického výkonu ▪ Izmerjena raven zvočne moči ▪ Nivel de potencia sonora medido ▪ Uppmätt ljudeffektsnivå

102 dB(A) LWA

Guaranteed Sound Power Level ▪ Гарантирано ниво на звукова мощност ▪ Garantovaný akustický výkon ▪ Garanteret lydstyrkeniveau ▪

Gegarandeerd geluidsniveau ▪ Garanteeritud helivõimsuse tase ▪ Taattu äänitehotaso ▪ Niveau de puissance sonore garanti ▪ Garantierter

Schalldruckpegel ▪ Εγγυημένο επίπεδο

ηχητικής ισχύος ▪ Szavatolt hangteljesítményszint ▪ Livello di potenza sonora garantito ▪ Garantētais skaņas

jaudas līmenis ▪ Garantuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna gwarantowana ▪ Nível sonoro farantido ▪

Nivelul garantat al puterii acustice ▪ Garantovaná hladina akustického výkonu ▪ Zajamčena raven zvočne moči ▪ Nivel de potencia sonora garantizado ▪

Garanterad ljudeffektsnivå

103 dB(A) LWA

Conformity Assessment Procedure (Noise) ▪ Оценка за съответствие на процедурата (Шум) ▪ Postup hodnocení plnění podmínek (hluk) ▪

Procedure for overensstemmelsesvurdering (Støj) ▪ Procedure van de conformiteitsbeoordeling (geluid) ▪ Vastavushindamismenetlus (müra) ▪

Vaatimustenmukaisuuden arviointimenettely (Melu) ▪ Procédure d’évaluation de conformité (bruit) ▪ Konformitätsbeurteilungsverfahren (Geräusch) ▪

∆ιαδικασία Αξιολόγησης Συμμόρφωσης (Θόρυβος) ▪ Megfelelőség-értékelési eljárás (Zaj) ▪ Procedura di valutazione della conformità (rumore) ▪

Atbilstības nov

ērtējuma procedūra (troksnis) ▪ Atitikties įvertinimo procedūra (garsas) ▪ Proċedura tal-Valutazzjoni tal-Konformità (Ħoss) ▪

Procedura oceny zgodności (poziom hałasu) ▪ Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităţii (zgomot) ▪

Postup vyhodnocovania zhodnosti (hluk) ▪ Postopek za ugotavljanje skladnosti (hrup) ▪ Procedimiento de evaluación de conformidad (ruido) ▪

Procedur för bedömning av överensstämmelse (buller)

2000/14/EC Annex VI, Part 1

SPECIFICATIONS 3

UK Notified Body for 2000/14/EC ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č. 2000/14/EC ▪

Det britiske bemyndigede organ for 2001/14/EF ▪ Engels adviesorgaan voor 2000/14/EG ▪ Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ

mõistes ▪ Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ▪ Organisme notifié concernant la directive 2000/14/CE ▪

Britische benannte Stelle für 2000/14/EG ▪ Κοινοποιημένος Οργανισμός Ηνωμένου Βασιλείου για 2000/14/ΕΚ ▪

2000/14/EK – egyesült királyságbeli bejelentett szervezet ▪ Organismo Notificato in GB per 2000/14/CE ▪ 2000/14/EK AK reģistrētā organizācija ▪

JK notifikuotosios įstaigos 2000/14/EC ▪ Korp Notifikat tar-Renju Unit għal 2000/14/KE ▪ Dopuszczona jednostka badawcza w Wielkiej Brytanii wg 2000/

14/WE ▪ Entidade notificada no Reino Unido para 2000/14/CE ▪ Organism notificat în Marea Britanie pentru 2000/14/CE ▪

Notifikovaný orgán Spojeného kráľovstva pre smernicu 2000/14/ES ▪ Britanski priglašeni organ za 2000/14/ES ▪

Cuerpo notificado en el Reino Unido para 2000/14/CE ▪ Anmält organ för 2000/14/EG i Storbritannien

Number: 1088

Sound Research Laboratories Limited

Holbrook House, Little Waldingfield

Sudbury, Suffolk CO10 0TH

Operator Ear Noise Level ▪ Оператор на нивото на доловим от ухото шум ▪ Hladina hluku v oblasti uší operátora ▪ Støjniveau i førers ørehøjde ▪

Geluidsniveau oor bestuurder ▪ Müratase operaatori kõrvas ▪ Melutaso käyttäjän korvan kohdalla ▪ Niveau de bruit à hauteur des oreilles de l’opérateur ▪

Schallpegel am Bedienerohr ▪ Επίπεδο θορύβου σε λειτουργία ▪ A kezelő fülénél mért zajszint ▪ Livello di potenza sonora all’orecchio dell’operatore ▪

Trokšņa līmenis pie operatora auss ▪ Dirbančiojo su mašina patiriamo triukšmo lygis ▪ Livell tal-Ħoss fil-Widna tal-Operatur ▪

Dopuszczalny poziom hałasu dla operatora ▪ Nível sonoro nos ouvidos do operador ▪ Nivelul zgomotului la urechea operatorului ▪

Hladina hluku pôsobiaca na sluch operátora ▪ Raven hrupa pri ušesu upravljavca ▪ Nivel sonoro en el oído del operador ▪ Ljudnivå vid förarens öra

86 dB(a) Leq (2006/42/EC)

Harmonised standards used ▪ Използвани хармонизирани стандарти ▪ Použité harmonizované normy ▪ Brugte harmoniserede standarder ▪

Gebruikte geharmoniseerde standaards

▪ Kasutatud ühtlustatud standardid ▪ Käytetyt yhdenmukaistetut standardit ▪ Normes harmonisées utilisées ▪

Angewandte harmonisierte Normen ▪ Εναρμονισμένα πρότυπα που χρησιμοποιήθηκαν ▪ Harmonizált szabványok ▪ Standard armonizzati applicati ▪

Izmantotie saskaņotie standarti ▪ Panaudoti suderinti standartai ▪ Standards armonizzati użati ▪ Normy spójne powiązane ▪ Normas harmonizadas usadas

▪ Standardele armonizate utilizate ▪ Použité harmonizované normy ▪ Uporabljeni usklajeni standardi ▪ Estándares armonizados utilizados ▪

Harmoniserade standarder som används

BS EN ISO 20643

BS EN ISO 5349-1

BS EN ISO 5349-2

BS EN 836

Technical standards and specifications used ▪ Използвани технически стандарти и спецификации ▪ Použité technické normy a specifikace ▪

Brugte tekniske standarder og specifikationer ▪ Gebruikte technische standaards en specificaties ▪ Kasutatud tehnilised standardid ja spetsifikatsioonid ▪

Käytetyt tekniset standardit ja eritelmät ▪ Spécifications et normes techniques utilisées ▪ Angewandte technische Normen und Spezifikationen ▪

Τεχνικά πρότυπα και προδιαγραφές που χρησιμοποιήθηκαν ▪ Műszaki szabványok és specifikációk

▪ Standard tecnici e specifiche applicati ▪

Izmantotie tehniskie standarti un specifikācijas ▪ Panaudoti techniniai standartai ir techninė informacija ▪ Standards u speċifikazzjonijiet tekniċi użati ▪

Normy i specyfikacje techniczne powiązane ▪ Normas técnicas e especificações usadas ▪ Standardele tehnice şi specificaţiile utilizate ▪

Použité technické normy a špecifikácie ▪ Uporabljeni tehnični standardi in specifikacije ▪ Estándares y especificaciones técnicas utilizadas ▪

Tekniska standarder och specifikationer som används

B71.4

ISO 2631-1

SAE J1194

The place and date of the declaration ▪ Място и дата на декларацията ▪ Místo a datum prohlášení ▪ Sted og dato for erklæringen ▪

Plaats en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la déclaration ▪

Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪ A nyilatkozat kelte (hely és idő) ▪ Luogo e data della dichiarazione ▪

Deklarācijas vieta un datums ▪ Deklaracijos vieta ir data ▪ Il-post u d-data tad-dikjarazzjoni ▪

Miejsce i data wystawienia deklaracji ▪ Local e data da

declaração ▪ Locul şi data declaraţiei ▪ Miesto a dátum vyhlásenia ▪ Kraj in datum izjave ▪ Lugar y fecha de la declaración ▪ Plats och datum för

deklarationen

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

February 5th, 2014

Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to

compile the technical file, and who is established in the Community.

Подпис на човека, упълномощен да състави декларацията от името на производителя, който поддържащ техническата документация и е

оторизиран да изготви техническия файл и е регистриран в общността.

Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávněné sestavit technické soubory a založené v

rámci Evropského společenství.

Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til

at udarbejde den tekniske journal, og som er baseret i nærområdet.

Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het

technische bestand samen te stellen, en die is gevestigd in het Woongebied.

Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus

koostada tehniline toimik.

Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan

tekniset asiakirjat ja joka on sijoittautunut yhteisöön.

Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et

qui est implantée dans la Communauté.

Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen a

ufbewahrt und berechtigt

ist, die technischen Unterlagen zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.

Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του κατασκευαστή, ο οποίος κατέχει την τεχνική έκθεση και έχει την

εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και ο οποίος είναι διορισμένος στην Κοινότητα.

A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszaki dokumentációt őrzi, engedéllyel rendelkezik a

műszaki fájl összeállításához, és aki a közösségben letelepedett személy.

Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire

il fascicolo tecnico, che deve essere stabilita nella Comunità.

Tās personas paraksts, kura ir pilnvarota deklarācijas sastādīšanai ražotāja vārdā, kurai ir tehniskā dokumentācija, kura ir pilnvarota sagatavot tehnisko

reģistru un kura ir apstiprin

āta Kopienā.

Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašė, turi visą techninę informaciją ir yra

įgaliotas sudaryti techninės informacijos dokumentą.

Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl

tekniku u li hija stabbilita fil-Komunità.

Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentację techniczną, upoważnioną do stworzenia

dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.

Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar

o processo técnico e que está estabelecida na Comunidade.

Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze

dosarul tehnic şi este stabilită în Comunitate.

Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovať technické podklady a ktorá

je umiestnená v Spoločenstve.

Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in lahko sestavlja spis tehnične dokumentacije, ter ima

sedež v Skupnosti.

Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el

archivo técnico y que está establecido en la Comunidad.

Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att

sammanställa den tekniska informationen och som är etablerad i gemenskapen.

2006/42/EC Annex II 1.A.2

Tim Lansdell

Technical Director

Ransomes Jacobsen Limited

West Road, Ransomes Europark,

Ipswich, IP3 9TT, England

2006/42/EC Annex II 1.A.10

Vasant Godhalekar

VP of Engineering

Jacobsen, A Textron Company

11524 Wilmar Blvd,

Charlotte, NC 28273, USA

Certificate Number ▪ Номер на сертификат ▪ Číslo osvědčení ▪ Certifikatnummer ▪ Certificaatnummer ▪ Sertifikaadi number ▪ Hyväksyntänumero ▪

Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪ Sertifikāta numurs ▪

Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo osvedčenia ▪ Številka certifikata ▪

Número de certificado ▪ Certifikatsnummer

4160165 Rev B

4 DECALS

4.1 DECALS _________________________________________________________________

Familiarize yourself with the following decals. They are critical to the safe operation of the

machine. REPLACE DAMAGED DECALS IMMEDIATELY.

4181865

4181864

• Read operator's manual. Do not allow untrained

operators to use machine.

• Keep shields in place and hardware securely

fastened.

• Keep hands, feet, and clothing away from moving

parts.

• Before you clean, adjust, or repair this equipment,

disengage all drives, engage parking brake, and stop

engine.

• Never carry passengers.

• Keep bystanders away.

• Do not use on slopes greater than 20°.

Danger

To avoid injury when working with battery:

1. Always connect the black (-) ground last and remove it

first.

2. Keep sparks and flames away, and avoid contact with

acid.

To avoid injury when jumping battery:

1. Connect positive (+) terminal to positive (+) terminal.

2. Connect negative (-) terminal on good battery to frame

of vehicle that has dead battery.

DECALS 4

Familiarize yourself with the following decals. They are critical to the safe operation of the

machine. REPLACE DAMAGED DECALS IMMEDIATELY.

4181862

4181861

4181860

4182520

WARNING

Radiator is under pressure. Remove

cap slowly to avoid personal injury.

IMPORTANT

DO NOT USE STARTING ASSIST FLUIDS

Use of starting assist fluids in the air intake system may be

potentially explosive or cause a "runaway" engine condition. This

could result in serious engine damage.

WARNING

Read mower manuals before operating or

performing any maintenance.

DANGER

To prevent injury, disengage all drives,

engage parking brake, stop engine, and

remove key before working on machine or

emptying grass catchers.

4 DECALS

105

3008521

3008004

4181863

WARNING

To prevent cuts use socket

wrench or Turf Groomer

knob to turn reel.

Traction Pedal

Reverse Forward

Engaged

Parking Brake

Disengaged

Sound Power

Level

CONTROLS 5

5 CONTROLS

5.1 ICONS ___________________________________________________________________

WARNING

Never attempt to drive the mower unless you have read the Safety and Operation Manual

and know how to operate all controls correctly.

Familiarize yourself with the icons shown above and what they represent. Learn the

location and purpose of all of the controls and gauges before operating this mower.

Coolant

Temperature

Read Manual Engine Throttle

High Low

Hour Meter

Traction Pedal

Forward Reverse

Fuel

Diesel

Cutting Units

Forward Off Reverse

(Cut) (Backlap)

Horn

Engine

Off Run Glow Plug Start

Engine Oil

Pressure

Parking Brake

Engaged Disengaged

LightsMowers

Lower Raise

Hydraulic

Oil Level

5 CONTROLS

A Tilt Steering Lever

B1 Parking Brake Lock

B2 Parking Brake Release

C Parking Brake Pedal

D Mow Speed Stop

E Traction Pedal - Forward

F Traction Pedal - Reverse

G Seat Adjustment

H Hydraulic Oil Cap

I Hydraulic Oil Light

J Fuel Cap

K Fuel Level Gauge

L Backlap Switch

M Hour Meter

N Water Temperature Gauge

O Volt Meter

P Engine Oil Pressure Light

Q Horn

R 2WD / 4WD Switch

S Raise / Lower Joystick

T Reel Switch

U Light Switch

V Ignition Switch

W Throttle

X Parking Brake Light

Y Fuse Blocks

Z Horn Switch

CONTROLS 5

5.2 CONTROL DESCRIPTIONS __________________________________________________

A. Tilt Steering Lever

Pull lever up to release steering column. Tilt column

up or down to position desired. Release lever to lock

steering column in place.

B. Parking Brake Lock / Release

To lock parking brake, hold brake pedal (C) down and

press lock (B

) until it engages. To disengage, press

brake pedal release (B

C. Parking Brake Pedal

To engage parking brake, press pedal down.

D. Mow Speed Stop

Limits forward speed while mowing. To operate at

lower travel speed while mowing, rotate lever so it

contacts stop screw (D1) on floor board when

forward travel pedal is pressed. To travel at full

speed, set lever in position shown (D3). Stop screw

(D2) can be adjusted to set specific mow speeds.

See the Parts & Maintenance manual.

Figure 5A

E. Traction Pedal Forward Travel

Press front of pedal down for forward travel. Release

pedal to slow mower and stop. Do not press traction

pedal when parking brake is set and parking brake light

(X) is lit.

F. Traction Pedal Reverse Travel

Press rear of pedal down for reverse travel. Release

pedal to slow mower and stop. Allow mower to come to

a complete stop before reversing directions. Do not

press traction pedal when parking brake is set and

parking brake light (X) is lit.

G. Seat Adjustment

Pull left side lever out to adjust seat forward or

backward. To adjust spring tension under seat, turn

adjusting knob on front of seat.

H. Hydraulic Oil Cap

Fill to “green” area on gauge using clean hydraulic fluid

while machine is cool. Do not overfill.

I. Hydraulic Oil Light

Alerts the operator of a low fluid level in

hydraulic tank. This light operates in

combination with the alarm. See Section 5.3.

J. Fuel Cap

Remove cap to fill fuel tank with clean, fresh, #2 low or

ultra low sulfur diesel fuel, minimum Cetane Rating of

45. See Section 6.10.

K. Fuel Level Gauge

Indicates current fuel level. Check fuel gauge daily

before starting machine.

Fill only to “green” area on

gauge; do not top off tank.

Do not allow machine to run

out of fuel.

L. Backlap Switch

The backlap switch allows the mowers to rotate in

reverse for backlapping.

Forward - For normal operation (mowing) the

switch must be set to the FORWARD (cut)

position.

Reverse - When backlapping, the mowers must

be operated in the reverse direction. Set switch

to the REVERSE (backlap) position.

When backlapping, the parking brake must be set and

both the reel switch (T) and backlap switch (L) must be

set to reverse. See Parts & Maintenance Manual.

M. Hour Meter

Records engine operating hours. Use hour meter to

schedule periodic maintenance.

N. Water Temperature Gauge

Indicates engine coolant temperature. Normal operating

temperature should be between 160° - 230°F (71°-

110°C). If temperature rises above 230°F (110°C),

alarm will sound. See Section 5.3.

O. Volt Meter

Indicates battery condition. During normal operation

meter should never be in the red area.

CAUTION

Never adjust steering while mower is moving. Stop

unit and set parking brake before adjusting.

Full Speed Reduced Speed

5 CONTROLS

P. Engine Oil Pressure Light

The indicator will light if engine oil pressure drops

below 7 PSI (0.48 BAR). Stop engine immediately,

determine the cause, and correct the problem before

resuming operation.

Q. Horn

The alarm sounds to alert the operator to conditions

requiring immediate attention. See Section 5.3.

R. 2 WD / 4 WD Switch

Sets mower into two or four wheel drive.

S. Raise / Lower Joystick

The joystick raises and lowers the mowers. Push

forward to lower mowers, pull back to raise mowers.

T. Reel Switch

The reel switch is a 3-position rocker type switch with a

neutral locking tab. It sets the mowers for either forward

or reverse rotation. Set mower switch in its OFF (center)

position when starting the mower.

Forward - To mow, press switch to the

FORWARD (cut) position. With the switch in this

position, mowers will start automatically when

they are lowered and stop when they are raised. Return

switch to its center position to disable mowers.

Reverse - The mower can be operated in the

reverse direction for backlapping, running

vertical mowers, removing grass build-up in

mowers, or dislodging objects binding mowers. To

reverse blade rotation, press switch to the REVERSE

position.

When backlapping, the parking brake must be set,

traction pedal in neutral, and both the reel switch (T)

and backlap switch (L) must be set to REVERSE. See

Parts & Maintenance Manual.

U. Light Switch

Controls operation of work lights.

V. Ignition Switch

The ignition switch has four positions. OFF - RUN -

GLOW PLUG - START. See Section 6.4.

W. Throttle

Controls engine speed. Run machine at full throttle

during normal machine operation.

X. Parking Brake Light

Indicates that the parking brake is engaged. Parking

brake must be disengaged before depressing traction

pedal.

Y. Fuse Blocks

Used to provide circuit protection for electrical

systems. See Parts & Maintenance Manual.

Z. Horn Switch

This switch is used to test the alarm system or disable

the alarm after a low oil level has been detected. Keep

switch in its ON position when starting and operating

mower. To test alarm, set switch to OFF and turn

ignition key to RUN. See

Section 5.3.

CONTROLS 5

5.3 OPERATOR ALERTS _______________________________________________________

The machine monitors vital machine systems. It uses an

audible alarm and warning lights to alert the operator of

conditions requiring immediate action. When an alert

occurs, follow the general guidelines listed in the chart below

and any specific actions outlined by the grounds

superintendent or service manager.

To test alarm system:

Turn ignition switch to RUN. Engine oil light will come on for

one second or more.

This system monitors:

1. Engine oil pressure.

2. Engine coolant temperature.

3. Hydraulic oil level.

Alert Action

1. Engine Oil Pressure - Oil pressure

light comes on. Oil pressure low.

Stop mower immediately, lower implements and shut off engine! Inspect oil

level in engine. If oil light remains on with oil at proper level, shut off engine and

tow or trailer mower back to a service area. NEVER operate engine with oil light

on, severe damage to the engine can occur.

2. Engine Coolant Temperature

Alarm sounds. Engine coolant

temperature high.

Stop mower immediately, lower implements and shut off engine! Remove

debris such as leaves and grass clippings that may be restricting air flow through

front screen and area between radiator and oil cooler. If engine continues to run

hot, return mower to a service area.

CAUTION: Engine coolant is under pressure. Turn engine off and allow

fluid to cool before checking fluid level or adding coolant to radiator.

3. Hydraulic fluid level - alarm

sounds and hydraulic fluid

warning light comes on.

Hydraulic fluid is below

recommended level.

Stop mower immediately, lower implements and shut off engine! Visually

inspect mower for obvious signs of leaks around connections, hoses and

hydraulic components. Return mower to service area for maintenance.

CAUTION: Hydraulic fluid is under pressure. Turn engine off and allow fluid

to cool before checking fluid level or adding oil to hydraulic tank.

6 OPERATION

6.1 DAILY INSPECTION________________________________________________________

1. Perform a visual inspection of the entire unit, look for

signs of wear, loose hardware, and missing or

damaged components. Check for fuel or oil leaks to

ensure connections are tight and hoses and tubes

are in good condition.

2. Check the fuel supply, radiator coolant level,

crankcase oil, and air cleaner indicator. All fluids

must be at the full level mark with engine cold.

3. Make sure all mowers are adjusted to the same

cutting height.

4. Check tires for proper inflation.

5. Test the Interlock System.

Note: For more detailed maintenance information,

adjustments and maintenance/lube charts, see the

Parts & Maintenance manual.

6.2 INTERLOCK SYSTEM ______________________________________________________

1. The Interlock System prevents the engine from

starting unless the parking brake is engaged, the

traction pedal is in neutral, and the reel switch is OFF.

The system also stops the engine if the operator

leaves the seat with the reel switch ON, traction

pedal out of NEUTRAL, or parking brake

DISENGAGED.

2. Perform each of the following tests to insure the

Interlock System is functioning properly. Stop the

test and have the system inspected and repaired if

any of the tests fail as listed below:

● the engine does not start in test 1;

● the engine does start during tests 2, 3 or 4;

● the engine continues to run during tests 5 or 6.

3. Refer to the chart below for each test and follow the

check (

) marks across the chart. Shut engine off

between each test.

Test 1: Represents normal starting procedure. The

operator is seated, parking brake is engaged, the

traction pedal is in neutral, and the reel switch is OFF.

The engine should start.

Test 2: The engine must not start if the reel switch is

ON.

Test 3: The engine must not start if the parking brake

is DISENGAGED.

Test 4: The engine must not start if traction pedal is

not in neutral.

Test 5: Start the engine in the normal manner then

turn reel switch ON and lift your weight off the seat.



Test 6: Start the engine in the normal manner then

disengage parking brake and lift your weight off the

seat.



Lift your weight off seat. The engine will shut down.

CAUTION

The daily inspection should be performed only when

the engine is off and all fluids are cold. Lower mowers

to the ground, engage the parking brake, stop engine,

and remove ignition key.

WARNING

Never operate equipment with the Interlock

System disconnected or malfunctioning. Do not

disconnect or bypass any switch.

Interlock System Check

Test Operator

Seated

Parking

Brake

Traction Pedal

in Neutral

Reel

Switch

Engine

Starts

Yes No Engaged Disengaged Yes No On Off Yes No

1   

2   

3 

4  

5 







6 



 



OPERATION 6

6.3 OPERATING PROCEDURES _________________________________________________

1. Under no circumstances should the engine be

started without the operator seated on the mower.

2. Do not operate mower or attachments with loose,

damaged, or missing components. Whenever

possible mow when grass is dry.

3. First mow in a test area to become thoroughly

familiar with the operation of the mower and control

levers.

Never operate the reels unless they are mowing

grass. Heat will develop between the bedknife and

reel and damage the cutting edge.

4. Study the area to determine the best and safest

operating procedure. Consider the height of the

grass, type of terrain, and condition of the surface.

Each condition will require certain adjustments or

precautions.

5. Never direct discharge of material toward

bystanders, nor allow anyone near the machine

while in operation. The owner/operator is

responsible for injuries inflicted to bystanders and/or

damage to their property.

6. Use discretion when mowing near gravel areas

(roadway, parking areas, cart paths, etc.). Stones

discharged from the implement may cause serious

injuries to bystanders and/or damage the

equipment.

7. Always turn reel switch off to stop blades when not

mowing.

8. Disengage the drive motors and raise the reels

when crossing paths or roadways. Look out for

traffic.

9. Stop and inspect the equipment for damage

immediately after striking an obstruction or if the

machine begins to vibrate abnormally. Have the

equipment repaired before resuming operation.

10. Slow down and use extra care on hillsides. Read

Section 6.7. Use caution when operating near drop

offs.

11. Look behind and down before backing up to be sure

the path is clear. Use care when approaching blind

corners, shrubs, trees, or other objects that may

obscure vision.

12. Never use your hands to clean cutting units. Use a

brush to remove grass clippings from blades. Blades

are extremely sharp and can cause serious injuries.

WARNING

A Roll Over Protection Structure (ROPS) is included with this mower. Seat belts must be worn whenever operating

a mower with a ROPS. Always keep seat belt snugly adjusted. DO NOT use seat belts on a mower without a ROPS.

If the mower is overturning, hold onto the steering wheel. Do not attempt to jump out or leave the seat.

CAUTION

To prevent injury, always wear safety glasses, leather work shoes or boots, a hard hat, and ear protection.

CAUTION

Before mowing, pick up all debris such as rocks, toys,

and wire which can be thrown by the machine. Enter a

new area cautiously. Always operate at speeds that

allow you to have complete control of the mower.

WARNING

Before you clean, adjust, or repair this equipment,

always disengage all drives, lower implements to

the ground, engage parking brake, stop engine,

and remove key from ignition switch to prevent

injuries.

6 OPERATION

6.4 STARTING _______________________________________________________________

IMPORTANT: Do not use starting assist fluids. Use of

such fluids in the air intake system may be potentially

explosive or cause a “Runaway” engine condition and

could result in serious engine damage.

1. Make sure fuel shut off valve is completely open and

the tow valve (See Section 6.9) is closed.

2. Sit in operator’s seat, make sure reel switch (T) is

OFF, parking brake (C) is engaged, and traction

pedal (E and F) is in neutral.

3. Move throttle lever between 1/8 to 1/2 throttle (W).

Turn ignition switch (V) to RUN. Parking brake light

(X) and engine oil light (P) should be lit.

4. Turn ignition switch to GLOW PLUG position for

about 3 to 5 seconds, then turn key to START

position. Release as soon as engine starts. The

colder the temperature, the longer it will take to

energize plugs. Do not hold switch in GLOW PLUG

position for more than 5 seconds, or in the START

position for more than 15 seconds. Energizing glow

plugs is not necessary when starting a warm

engine. Once engine starts, engine oil light (P)

should go out.

5. Allow the engine to become warm and properly

lubricated before operating at high RPM.

Figure 6A

6.5 STOPPING / PARKING _____________________________________________________

To stop:

Remove your foot from traction pedal. The mower will

automatically brake when the traction pedal returns to

neutral.

To park the mower under normal conditions:

1. Disengage the reel switch, raise the implements, and

move away from the area of operation.

2. Select a flat and level area to park.

a. Release traction pedal to bring the mower to a

complete stop.

b. Disengage all drives, lower implements to the

ground, reduce throttle to slow, and allow engine

to operate at no load for several minutes.

3. Engage parking brake, stop the engine, and always

remove the ignition key.

If an emergency arises and the mower must be parked in

the area of operation, follow the guidelines outlined by

the grounds superintendent. If the mower is parked on an

incline, chock or block the wheels.

NOTICE

Permanent damage to the turbocharger may occur if

the engine is shut down without allowing the

turbocharger time to cool.

To prevent damage, operate the engine with no load

and at half throttle for 3 to 5 minutes before shutting

off engine.

Leht laaditakse ...

Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

Kaubamärk: Jacobsen

Mudel: 67955, 67956, 67957, 68007, 68008

Kategooria: Muruniidukid

Tüüp: Omaniku manuaal

See juhend sobib ka

Laadige alla PDF

aruanne

teistes keeltes

English: Jacobsen 67955, 67956, 67957, 68007, 68008 Owner's manual

Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

See juhend sobib ka

Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid