Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

Kategooria
Muruniidukid
Tüüp
Omaniku manuaal

See käsiraamat sobib ka

Safety, Operation, & Maintenance Manual
WARNING
Warning: If incorrectly used, this machine can
cause severe injury. Those who use and maintain
this machine should be trained in its proper use,
warned of its dangers, and must read the entire
manual before attempting to set up, operate, adjust,
or service the machine.
GB
Super LF 1880™ Fairway Mower with ROPS
67955 – Kubota D1105-E3B, 2WD
67956 – Kubota D1105-E3B, 4WD
67957 – Kubota D1105-T-E3B, 4WD
68007 – Kubota D1105-E4B, 2WD
68008 – Kubota D1105-E4B, 4WD
4160165-Rev B
2
This manual contains safety and operating instructions
for your new Jacobsen machine. This manual should be
stored with the equipment for reference during operation.
Before you operate your machine, you and each operator
you employ should read the manual carefully in its
entirety. By following the safety, operating, and
maintenance instructions, you will prolong the life of your
equipment, and maintain its maximum efficiency.
If additional information is needed, contact your
Jacobsen Dealer.
The serial plate is located on the left rear frame rail.
Jacobsen recommends you record these numbers below
for easy reference.
CHARLOTTE, NC
YEAR OF
PRODUCTION:
MADE IN U.S.A.
®
A Textron Company
FOREWORD
1 CONTENTS
© Copyright 2008, Textron Inc. “All rights reserved, including the
right to reproduce this material or portions thereof in any form.
Proposition 65 Warning
This product contains or emits
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
Litho In U.S.A. 2-2014
CONTENTS 1
3
1CONTENTS
2SAFETY
2.1 Operating Safety .................................................. 4
2.2 Important Safety Notes .........................................5
3 SPECIFICATIONS
3.1 Product Identification............................................ 6
3.2 Kubota D1105-E Engine .......................................6
3.3 Kubota D1105-TE Engine ....................................6
3.4 Cutting Units .........................................................7
3.5 Mower ...................................................................7
3.6 Weights and Dimensions ......................................7
3.7 Accessories & Support Literature .........................7
3.8 Declaration of Conformity .....................................8
4DECALS
4.1 Decals ................................................................ 10
5 CONTROLS
5.1 Icons................................................................... 13
5.2 Control Descriptions ...........................................15
5.3 Operator Alerts ...................................................17
6 OPERATION
6.1 Daily Inspection .................................................. 18
6.2 Interlock System .................................................18
6.3 Operating Procedures ........................................19
6.4 Starting ...............................................................20
6.5 Stopping / Parking ..............................................20
6.6 To Drive / Transport ...........................................21
6.7 Hillside Operation ...............................................21
6.8 Mowing ...............................................................22
6.9 Towing / Trailering ..............................................22
6.10 Daily Maintenance ..............................................23
7 MAINTENANCE & LUBRICATION CHARTS
7.1 General............................................................... 24
7.2 Lubrication Chart ................................................24
7.3 Maintenance Charts ...........................................25
8 MAINTENANCE
8.1 General............................................................... 26
8.2 Engine ................................................................26
8.3 Engine Oil ...........................................................26
8.4 Air Filter ..............................................................27
8.5 Fuel ....................................................................27
8.6 Fuel System .......................................................27
8.7 Battery ................................................................28
8.8 Jump Starting .....................................................28
8.9 Charging Battery ................................................28
8.10 Hydraulic Hoses .................................................29
8.11 Hydraulic Oil and Filters .....................................29
8.12 Electrical System ................................................30
8.13 Muffler and Exhaust ...........................................31
8.14 Tires ...................................................................31
8.15 Wheel Mounting Procedure ................................31
8.16 Roll Over Protective Structure (ROPS) ..............31
8.17 Care and Cleaning .............................................32
8.18 Radiator ..............................................................32
8.19 Backlapping ........................................................33
8.20 Storage ...............................................................34
9 ADJUSTMENTS
9.1 General.............................................................. 35
9.2 Engine Belt ........................................................ 35
9.3 Throttle .............................................................. 35
9.4 Neutral Switch and 4WD Cut-Out Switch .......... 36
9.5 Transport Speed ................................................ 36
9.6 Traction Pedal Speed Limiter ............................ 37
9.7 Parking Brake .................................................... 37
9.8 Brake Switch ...................................................... 37
9.9 Steering Adjustments ........................................ 38
9.10 Lift Limit Switch .................................................. 38
9.11 Bedknife-To-Reel ............................................... 39
9.12 Bedknife Adjustment .......................................... 40
9.13 Cutting Height .................................................... 40
9.14 Reel Bearing ...................................................... 41
9.15 Bedknife Adjuster Spring ................................... 41
9.16 Bedknife Adjuster Tension ................................. 41
9.17 Grinding Bedknife .............................................. 41
9.18 Flash Attach ....................................................... 42
9.19 Down Pressure .................................................. 42
9.20 Torque Specification .......................................... 43
9.21 Specific Torque .................................................. 43
10 PROBLEM SOLVING
10.1 General Problem Solving................................... 44
11 QUALITY OF CUT
11.1 Quality of Cut Problem Solving.......................... 45
11.2 Washboarding ................................................... 45
11.3 Marcelling .......................................................... 46
11.4 Step Cutting ....................................................... 47
11.5 Scalping ............................................................. 48
11.6 Stragglers .......................................................... 49
11.7 Streaks .............................................................. 50
11.8 Windrowing ........................................................ 51
11.9 Rifling Or Tramlining .......................................... 52
11.10 Mismatched Cutting Units .................................. 52
12 NOTES
2 SAFETY
4
2 SAFETY
2.1 OPERATING SAFETY ______________________________________________________
1. Safety is dependent upon the awareness, concern,
and prudence of those who operate or service the
equipment. Never allow minors to operate any
equipment.
2. It is your responsibility to read this manual and all
publications associated with this equipment (Parts
and Maintenance Manual, Engine Manual, and
attachments/accessories instruction sheets). If the
operator cannot read English it is the owner’s
responsibility to explain the material contained in
this manual to them.
3. Learn the proper use of the machine, the location and
purpose of all the controls and gauges, before you
operate the equipment. Working with unfamiliar
equipment can lead to accidents.
4. Never allow anyone to operate or service the machine
or its attachments without proper training and
instructions; or while under the influence of alcohol or
drugs.
5. Wear all the necessary protective clothing and
personal safety devices to protect your head, eyes,
ears, hands, and feet. Operate the machine only in
daylight or in good artificial light.
6. Evaluate the terrain to determine what accessories and
attachments are needed to properly and safely perform
the job. Only use accessories and attachments
approved by Jacobsen.
7. Stay alert for holes in the terrain and other hidden
hazards.
8. Inspect the area where the equipment will be used.
Pick up all the debris you can find before operating.
Beware of overhead obstructions (low tree limbs,
electrical wires, etc.) and also underground obstacles
(sprinklers, pipes, tree roots, etc.). Enter a new area
cautiously. Stay alert for hidden hazards.
9. Never direct discharge of material toward bystanders,
nor allow anyone near the machine while in operation.
The owner/operator can prevent and is responsible for
injuries inflicted to themselves, to bystanders, and
damage to property.
10. Do not carry passengers. Keep bystanders and pets a
safe distance away.
11. Never operate equipment that is not in perfect working
order or is without decals, guards, shields, discharge
deflectors, or other protective devices securely
fastened in place.
12. Never disconnect or bypass any switch.
13. Do not change the engine governor setting or
overspeed the engine.
14. Carbon monoxide in the exhaust fumes can be fatal
when inhaled. Never operate the engine without proper
ventilation or in an enclosed area.
15. Fuel is highly flammable; handle with care.
16. Keep the engine clean. Allow the engine to cool before
storing and always remove the ignition key.
17. Disengage all drives and engage parking brake before
starting the engine (motor). Start the engine only when
sitting in operator’s seat, never while standing beside
the unit.
18. Equipment must comply with the latest federal, state,
and local requirements when driven or transported on
public roads. Watch out for traffic when crossing or
operating on or near roads.
19. Local regulations may restrict the age of the operator.
20. Operate the machine up and down the face of slopes
(vertically), not across the face (horizontally).
21. To prevent tipping or loss of control, do not start or
stop suddenly on slopes. Reduce speed when making
sharp turns. Use caution when changing directions.
22. Always use the seat belt when operating mowers
equipped with a Roll Over Protective Structure
(ROPS).
Never use a seat belt when operating mowers
without a ROPS.
Accessory operator protective structures will
continue to be offered for all equipment currently
covered. This allows for the outfitting of any
machines without previous ROPS installations or
replacement of damaged structures.
23. Keep legs, arms and body inside the seating
compartment while the vehicle is in motion.
This machine is to be operated and maintained as specified in this manual and is intended for the professional
maintenance of specialized turf grasses. It is not intended for use on rough terrain or long grasses.
WARNING
EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.
Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive
instruction from someone familiar with the equipment before being allowed to operate the machine.
!
SAFETY 2
5
2.2 IMPORTANT SAFETY NOTES ________________________________________________
This safety alert symbol is used to alert you to potential hazards.
DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious
injury.
CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury
and property damage. It may also be used to alert against unsafe practices.
NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may
also be used to alert against unsafe practices.
For pictorial clarity, some illustrations in this manual may show shields, guards, or plates open or removed. Under no
circumstances should this equipment be operated without these devices securely fastened in place.
By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum
efficiency. Adjustments and maintenance should always be performed by a qualified technician.
If additional information or service is needed, contact your Authorized Jacobsen Dealer, who is kept informed of the
latest methods to service this equipment, and can provide prompt and efficient service. Use of other than original or
authorized Jacobsen parts and accessories will void the warranty.
WARNING
The Interlock System on this mower prevents the mower from starting unless
the brake lever is engaged, mower switch is off, and traction pedal is in
neutral. The system will stop the engine if the operator leaves the seat
without engaging the parking brake or setting the mower switch off.
NEVER operate mower unless the Interlock System is working.
!
WARNING
1. Before leaving the operator’s position for any reason:
a. Return traction pedal to neutral.
b. Disengage all drives.
c. Lower all implements to the ground.
d. Engage parking brake.
e. Stop engine and remove the ignition key.
2. Keep hands, feet, and clothing away from moving parts. Wait for all
movement to stop before you clean, adjust, or service the machine.
3. Keep the area of operation clear of all bystanders and pets.
4. Never carry passengers, unless a seat is provided for them.
5. Never operate mowing equipment without the discharge deflector
securely fastened in place.
!
3 SPECIFICATIONS
6
3 SPECIFICATION S
3.1 PRODUCT IDENTIFICATION _________________________________________________
67955.............................. Super LF 1880 2WD with ROPS
67956.............................. Super LF 1880 4WD with ROPS
67957.............................. Super LF 1880 Turbo 4WD with
ROPS
68007.............................. Super LF 1880 2WD with ROPS
68008.............................. Super LF 1880 4WD with ROPS
Serial Number ................ An identification plate, like the one
shown, listing the serial number, is
attached to theleft rear frame of
rail of the mower.
Always provide the serial number of the unit when ordering
replacement parts or requesting service information.
3.2 KUBOTA D1105-E ENGINE __________________________________________________
Make ............................... Kubota
Model .............................. D1105-E3B (67955 and 67956)
Model .............................. D1105-E4B (68007 and 68008)
Horsepower..................... 24.8 hp (18.5 kW) @3000 RPM
Note: Actual sustained horsepower will likely be lower
than listed in specifications due to operating limitations
and environmental factors.
Displacement .................. 68.5 cu. In. (1123 cc)
Torque............................. 52.7 ft lbs. (71.5 Nm) @ 2200
RPM
Fuel:
Type .......................... No. 2 Low or Ultra Low Sulfur
Diesel
Rating ....................... Cetane Rating-45
Capacity.................... 12 U.S. Gal. (45.4 liters)
High speed - rpm............ 3150 no load
Low Idle - rpm................. 1750 no load
Lubrication:
Capacity.................... 5.4 qt (5.1 liters)
Type .......................... SAE 10W30
API Classification ..... CD,CE
Air Filter .......................... Dry type with service indicator
Alternator ........................ 40 amp
Cooling System .............. Liquid Cooled
3.3 KUBOTA D1105-TE ENGINE _________________________________________________
Make ............................... Kubota
Model .............................. D1105-T-E3B (67957)
Horsepower..................... 32.9 hp (24.5 kW) @3000 RPM
Note: Actual sustained horsepower will likely be lower
than listed in specifications due to operating limitations
and environmental factors.
Displacement .................. 68.5 cu. In. (1123 cc)
Torque............................. 65 ft. lbs. (88.1 Nm) @ 2200 RPM
Fuel:
Type .......................... No. 2 Low or Ultra Low Sulfur
Diesel
Rating ....................... Cetane Rating-45
Capacity.................... 12 U.S. gal. (45.4 liters)
High speed - rpm ............ 3150 no load
Low Idle - rpm ................. 1750 no load
Lubrication:
Capacity.................... 5.4 qt. (5.1 liters)
Type .......................... SAE 10W30
API Classification ..... CD,CE
Air Filter .......................... Dry type with service indicator
Alternator ........................ 40 amp
Cooling System .............. Liquid Cooled
Product
EEC Sound
Power
Vibration M/S
2
Arms Body
67955
67956
67957
68007
68008
<105 dba
<105 dba
<105 dba
3.578
3.578
2.758
0.0246
0.0246
0.0318
11524 WILMAR BLVD,
CHARLOTTE, NC 28273
®
kg kW
1-800-848-1636 (US)
PRODUCT OF U.S.A.
A Textron Company
849.1 18.5 XXXX
67955001651
SPECIFICATIONS 3
7
3.4 CUTTING UNITS ___________________________________________________________
Reel.................................5 Reels, 18 in. (457 mm) wide
Reel Diameter .................5 in. (127 mm)
Blade Options .................8 or 11 blades
Cutting Height .................0.30 to 0.70 in. (7.6 to 18 mm)
Cutting Width .................. 82 in. (2032 mm)
Cutting Frequency:
8 Blade...................... 0.067 in./mph (1.06 mm/kph)
11 Blade.................... 0.049 in./mph (0.77 mm/kph)
3.5 MOWER__________________________________________________________________
Tires
Front.......................... 24 x 13-12 2 Ply
Rear ..........................18 x 9.5-8 2 Ply
Pressure:.........................10-12 psi (0.69 - 0.83 BAR)
Battery:
Type ..........................12 Volt Lead/Acid
Group ........................ 45 GMF
Speed:
Mow (4 WD) ..............0 - 6 mph (9.6 kph)
Transport (2 WD)....... 0 - 10.5 mph (16.9 kph)
Reverse..................... 0 - 4 mph (6.4 kph)
Parking Brake ................. Mechanical front wheel disc
Hydraulic System:
Capacity.......................... 8 U.S. gal. (30.28 liters) System
Fluid Type ....................... GreensCare™ 68
Return Filter.................... Full Flow 10 micron
Charge Filter................... Full Flow 10 micron
Steering ......................... Hydrostatic Power Steering
Mower Lift ....................... Hydraulic Double Acting Cylinders
3.6 WEIGHTS AND DIMENSIONS ________________________________________________
Dimensions: Inches (mm)
Length - Grass Catchers On ......................... 106 (2692)
Height - Top of Steering Wheel ....................... 56 (1422)
Wheel Base.................................................. 59.1 (1501)
Width - Transport Position ............................ 88.5 (2248)
Width - Mowing Position............................... 88.5 (2248)
Width - Wheel ............................................ 74.25 (1886)
Turning Radius ................................................ 18 (457)
Weights: Lbs. (kg)
Working Weight Less Operator
67955 .......................................................... 2205 (1000)
67956 .......................................................... 2280 (1034)
67957 .......................................................... 2330 (1057)
68007 .......................................................... 2205 (1000)
68008 .......................................................... 2280 (1034)
3.7 ACCESSORIES & SUPPORT LITERATURE _____________________________________
Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.
Accessories
Air Blow Gun ...........................................................JAC5098
Orange Touch-up Paint (12 oz. spray) ...................... 554598
Arm Rest ................................................................. 4139431
Grass Catcher............................................................. 67930
Powered Rear Roller Cleaner Brush ........................... 67929
Turf Groomer 1/2 in. Spacing ...................................... 67926
2 Post ROPS............................................................... 66194
Canopy (Requires 2 Post ROPS)................................ 68095
4WD Field Conversion Kit ........................................... 67931
Vertical Mower Lift Yoke Kit......................................... 67934
High Cut Roller Kit 15/16 in......................................... 68634
Vertical Mower ............................................................ 67928
MAGSystem™ Kit ................................................... 4161022
Reels
8 Blade Reel ................................................................62837
11 Blade Reel ..............................................................62838
Rollers
3 in. dia. Grooved Front Roller with Scraper................67925
2-3/16 in. Solid Front Roller with Scraper ....................68626
2-3/16 in. Grooved Front Roller ...................................68616
2-3/16 in. Full Width Solid Rear Roller with Scraper....68674
Support Literature
Safety & Operation Manual......................................4160165
Parts & Maintenance Manual...................................4160164
Diesel Engine Parts Catalog....................................4160162
Operator Training Video...........................................4102141
Service & Repair Manual.........................................4171721
CAUTION
Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the
equipment.
!
3 SPECIFICATIONS
8
3.8 DECLARATION OF CONFORMITY ____________________________________________
DECLARATION OF CONFORMITY ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ PROHLÁŠENÍ O SHODĚ
OVERENSSTEMMELSESERKLÆRING CONFORMITEITSVERKLARING VASTAVUSDEKLARATSIOON
VAATIMUSTENMUKAISUUSVAKUUTUS DECLARATION DE CONFORMITE KONFORMITÄTSERKLÄRUNG
∆ΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ MEGFELELŐSÉGI NYILATKOZAT DICHIARAZIONE DI CONFORMITÀ ATBILSTĪBAS
DEKLARĀCIJA ATITIKTIES DEKLARACIJA DIKJARAZZJONI TAL-KONFORMITÀ DEKLARACJA ZGODNOŚCI
DECLARAÇÃO DE CONFORMIDADE DECLARAŢIE DE CONFORMITATE VYHLÁSENIE O ZHODE IZJAVA O
SKLADNOSTI DECLARACIÓN DE CONFORMIDAD DEKLARATION OM ÖVERENSSTÄMMELSE
Business name and full address of the manufacturer Търговско име и пълен адрес на производителя Obchodní jméno a plná adresa výrobce
Producentens firmanavn og fulde adresse Bedrijfsnaam en volledig adres van de fabrikant Tootja ärinimi ja täielik aadress
Valmistajan toiminimi ja täydellinen osoite Nom commercial et adresse complète du fabricant Firmenname und vollständige Adresse des Herstellers
Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή A gyártó üzleti neve és teljes címe Ragione sociale e indirizzo completo del fabbricante
Uzņēmuma nosaukums un pilna ražotāja adrese Verslo pavadinimas ir pilnas gamintojo adresas Isem kummerċjali u indirizz sħiħ tal-fabbrikant
Nazwa firmy i pełny adres producenta Nome da empresa e endereço completo do fabricante Denumirea comercială şi adresa completă a
producătorului Obchodný názov a úplná adresa výrobcu Naziv podjetja in polni naslov proizvajalca Nombre de la empresa y dirección completa del
fabricante Tillverkarens företagsnamn och kompletta adress
Jacobsen, A Textron Company
11524 Wilmar Blvd.
Charlotte, NC 28273, USA
Product Code Код
на продукта Kód výrobku Produktkode Productcode Toote kood Tuotekoodi Code produit Produktcode Κωδικός προϊόντος
Termékkód Codice prodotto Produkta kods Produkto kodas Kodiċi tal-Prodott Kod produktu Código do Produto Cod produs Kód výrobku
Oznaka proizvoda Código de producto Produktkod
67955
67956
67957
68007
68008
Machine Name Наименование на машината Název stroje Maskinnavn Machinenaam Masina nimi Laitteen nimi Nom de la machine
Maschinenbezeichnung Ονομασία μηχανήματος Gépnév Denominazione della macchina Iekārtas nosaukums Mašinos pavadinimas Isem tal-
Magna Nazwa urządzenia
Nome da Máquina Numele echipamentului Názov stroja Naziv stroja Nombre de la máquina Maskinens namn
SLF 1880 2WD
SLF 1880 4WD
SLF 1880 4WD Turbo
SLF 1880 2WD
SLF 1880 4WD
Designation Предназначение Označení Betegnelse Benaming Nimetus Tyyppimerkintä Pažymėjimas Bezeichnung Χαρακτηρισμός
Megnevezés Funzione Apzīmējums Lithuanian Denominazzjoni Oznaczenie Designação Specificaţie Označenie Namen stroja Descripción
Beteckning
Lawnmower, Article 12, Item 32
Serial Number Сериен номер Sériové číslo Serienummer Serienummer Seerianumber Valmistusnumero Numéro de série Seriennummer
Σειριακός
αριθμός Sorozatszám Numero di serie Sērijas numurs Serijos numeris Numru Serjali Numer seryjny Número de Série Număr de
serie Sériové číslo Serijska številka Número de serie Serienummer
6795501651-6795502500
6795501651-6795502500
6795501651-6795502500
6800701651-6800702500
6800801651-6800802500
Engine Двигател Motor Motor Motor Mootor Moottori Moteur Motor Μηχανή Modulnév Motore Dzinējs Variklis Saħħa Netta Installata
Silnik Motor Motor Motor Motor Motor Motor
Kubota D1105-E3B Diesel
Kubota D1105-E3B Diesel
Kubota D1105-T-E3B Diesel
Kubota D1105-E3B Diesel
Kubota D1105-E3B Diesel
Net Installed Power Нетна инсталирана мощност
Čistý instalovaný výkon Installeret nettoeffekt Netto geïnstalleerd vermogen Installeeritud
netovõimsus Asennettu nettoteho Puissance nominale nette Installierte Nettoleistung Καθαρή εγκατεστημένη ισχύς Nettó beépített teljesítmény
Potenza netta installata Paredzētā tīkla jauda Grynoji galia Wisa’ tal-Qtugħ Moc zainstalowana netto Potência instalada Puterea instalată netă
Čistý inštalovaný výkon Neto vgrajena moč Potencia instalada neta Nettoeffekt
18,5 kW @ 3000 RPM
18,5 kW @ 3000 RPM
24,5 kW @ 3000 RPM
18,5 kW @ 3000 RPM
18,5 kW @ 3000 RPM
Cutting Width Широчина на рязане Šířka řezu Skærebredde Maaibreedte Lõikelaius Leikkuuleveys Largeur de coupe Schnittbreite
Μήκος μισινέζας
Vágási szélesség Larghezza di taglio Griešanas platums Pjovimo plotis Tikkonforma mad-Direttivi Szerokość cięcia
Largura de Corte Lăţimea de tăiere Šírka záberu Širina reza Anchura de corte Klippbredd
203 cm
Conforms to Directives В съответствие с директивите Splňuje podmínky směrnic Er i overensstemmelse med direktiver Voldoet aan de richtlijnen
Vastab direktiividele Direktiivien mukainen Conforme aux directives Entspricht Richtlinien Ακολουθήστε πιστά τις Οδηγίες Megfelel az irányelveknek
Conforme alle Direttive Atbilst direktīvām Atitinka direktyvų reikalavimus Valutazzjoni tal-Konformità Dyrektywy związane Cumpre as Directivas
Respectă Directivele
Je v súlade so smernicami Skladnost z direktivami Cumple con las Directivas Uppfyller direktiv
2004/108/EC
2006/42/EC
2000/14/EC, 2005/88/EC
2006/66/EC
Conformity Assessment Оценка за съответствие Hodnocení plnění podmínek Overensstemmelsesvurdering Conformiteitsbeoordeling
Vastavushindamine Vaatimustenmukaisuuden arviointi Evaluation de conformité Konformitätsbeurteilung ∆ιαπίστωση Συμμόρφωσης
Megfelelőség-értékelés Valutazione della conformità Atbilstības novērtējums Atitikties įvertinimas Livell tal-Qawwa tal-Ħoss Imkejjel Ocena
zgodności Avaliação de Conformidade Evaluarea conformităţii Vyhodnotenie zhodnosti Ocena skladnosti Evaluación de conformidad
Bedömning av överensstämmelse
2006/42/EC Annex VIII
Measured Sound Power Level Измерено ниво на звукова мощност Naměř
ený akustický výkon Målte lydstyrkeniveau Gemeten geluidsniveau
Mõõdetud helivõimsuse tase Mitattu äänitehotaso Niveau de puissance sonore mesuré Gemessener Schalldruckpegel
Σταθμισμένο επίπεδο ηχητικής ισχύος Mért hangteljesítményszint Livello di potenza sonora misurato Izmērītais skaņas jaudas līmenis
Išmatuotas garso stiprumo lygis Livell tal-Qawwa tal-Ħoss Iggarantit Moc akustyczna mierzona Nível sonoro medido Nivelul măsurat al puterii
acustice Nameraná hladina akustického výkonu Izmerjena raven zvočne moči Nivel de potencia sonora medido Uppmätt ljudeffektsnivå
102 dB(A) LWA
Guaranteed Sound Power Level Гарантирано ниво на звукова мощност Garantovaný akustický výkon Garanteret lydstyrkeniveau
Gegarandeerd geluidsniveau Garanteeritud helivõimsuse tase Taattu äänitehotaso Niveau de puissance sonore garanti Garantierter
Schalldruckpegel Εγγυημένο επίπεδο
ηχητικής ισχύος Szavatolt hangteljesítményszint Livello di potenza sonora garantito Garantētais skaņas
jaudas līmenis Garantuotas garso stiprumo lygis Livell tal-Qawwa tal-Ħoss Iggarantit Moc akustyczna gwarantowana Nível sonoro farantido
Nivelul garantat al puterii acustice Garantovaná hladina akustického výkonu Zajamčena raven zvočne moči Nivel de potencia sonora garantizado
Garanterad ljudeffektsnivå
103 dB(A) LWA
Conformity Assessment Procedure (Noise) Оценка за съответствие на процедурата (Шум) Postup hodnocení plnění podmínek (hluk)
Procedure for overensstemmelsesvurdering (Støj) Procedure van de conformiteitsbeoordeling (geluid) Vastavushindamismenetlus (müra)
Vaatimustenmukaisuuden arviointimenettely (Melu) Procédure d’évaluation de conformité (bruit) Konformitätsbeurteilungsverfahren (Geräusch)
∆ιαδικασία Αξιολόγησης Συμμόρφωσης (Θόρυβος) Megfelelőség-értékelési eljárás (Zaj) Procedura di valutazione della conformità (rumore)
Atbilstības nov
ērtējuma procedūra (troksnis) Atitikties įvertinimo procedūra (garsas) Proċedura tal-Valutazzjoni tal-Konformità (Ħoss)
Procedura oceny zgodności (poziom hałasu) Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităţii (zgomot)
Postup vyhodnocovania zhodnosti (hluk) Postopek za ugotavljanje skladnosti (hrup) Procedimiento de evaluación de conformidad (ruido)
Procedur för bedömning av överensstämmelse (buller)
2000/14/EC Annex VI, Part 1
SPECIFICATIONS 3
9
UK Notified Body for 2000/14/EC Нотифициран орган в Обединеното кралство за 2000/14/ЕО Úřad certifikovaný podle směrnice č. 2000/14/EC
Det britiske bemyndigede organ for 2001/14/EF Engels adviesorgaan voor 2000/14/EG Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ
mõistes Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa Organisme notifié concernant la directive 2000/14/CE
Britische benannte Stelle für 2000/14/EG Κοινοποιημένος Οργανισμός Ηνωμένου Βασιλείου για 2000/14/ΕΚ
2000/14/EK – egyesült királyságbeli bejelentett szervezet Organismo Notificato in GB per 2000/14/CE 2000/14/EK AK reģistrētā organizācija
JK notifikuotosios įstaigos 2000/14/EC Korp Notifikat tar-Renju Unit għal 2000/14/KE Dopuszczona jednostka badawcza w Wielkiej Brytanii wg 2000/
14/WE Entidade notificada no Reino Unido para 2000/14/CE Organism notificat în Marea Britanie pentru 2000/14/CE
Notifikovaný orgán Spojeného kráľovstva pre smernicu 2000/14/ES Britanski priglašeni organ za 2000/14/ES
Cuerpo notificado en el Reino Unido para 2000/14/CE Anmält organ för 2000/14/EG i Storbritannien
Number: 1088
Sound Research Laboratories Limited
Holbrook House, Little Waldingfield
Sudbury, Suffolk CO10 0TH
Operator Ear Noise Level Оператор на нивото на доловим от ухото шум Hladina hluku v oblasti uší operátora Støjniveau i førers ørehøjde
Geluidsniveau oor bestuurder Müratase operaatori kõrvas Melutaso käyttäjän korvan kohdalla Niveau de bruit à hauteur des oreilles de l’opérateur
Schallpegel am Bedienerohr Επίπεδο θορύβου σε λειτουργία A kezelő fülénél mért zajszint Livello di potenza sonora all’orecchio dell’operatore
Trokšņa līmenis pie operatora auss Dirbančiojo su mašina patiriamo triukšmo lygis Livell tal-Ħoss fil-Widna tal-Operatur
Dopuszczalny poziom hałasu dla operatora Nível sonoro nos ouvidos do operador Nivelul zgomotului la urechea operatorului
Hladina hluku pôsobiaca na sluch operátora Raven hrupa pri ušesu upravljavca Nivel sonoro en el oído del operador Ljudnivå vid förarens öra
86 dB(a) Leq (2006/42/EC)
Harmonised standards used Използвани хармонизирани стандарти Použité harmonizované normy Brugte harmoniserede standarder
Gebruikte geharmoniseerde standaards
Kasutatud ühtlustatud standardid Käytetyt yhdenmukaistetut standardit Normes harmonisées utilisées
Angewandte harmonisierte Normen Εναρμονισμένα πρότυπα που χρησιμοποιήθηκαν Harmonizált szabványok Standard armonizzati applicati
Izmantotie saskaņotie standarti Panaudoti suderinti standartai Standards armonizzati użati Normy spójne powiązane Normas harmonizadas usadas
Standardele armonizate utilizate Použité harmonizované normy Uporabljeni usklajeni standardi Estándares armonizados utilizados
Harmoniserade standarder som används
BS EN ISO 20643
BS EN ISO 5349-1
BS EN ISO 5349-2
BS EN 836
Technical standards and specifications used Използвани технически стандарти и спецификации Použité technické normy a specifikace
Brugte tekniske standarder og specifikationer Gebruikte technische standaards en specificaties Kasutatud tehnilised standardid ja spetsifikatsioonid
Käytetyt tekniset standardit ja eritelmät Spécifications et normes techniques utilisées Angewandte technische Normen und Spezifikationen
Τεχνικά πρότυπα και προδιαγραφές που χρησιμοποιήθηκαν Műszaki szabványok és specifikációk
Standard tecnici e specifiche applicati
Izmantotie tehniskie standarti un specifikācijas Panaudoti techniniai standartai ir techninė informacija Standards u speċifikazzjonijiet tekniċi użati
Normy i specyfikacje techniczne powiązane Normas técnicas e especificações usadas Standardele tehnice şi specificaţiile utilizate
Použité technické normy a špecifikácie Uporabljeni tehnični standardi in specifikacije Estándares y especificaciones técnicas utilizadas
Tekniska standarder och specifikationer som används
B71.4
ISO 2631-1
SAE J1194
The place and date of the declaration Място и дата на декларацията Místo a datum prohlášení Sted og dato for erklæringen
Plaats en datum van de verklaring Deklaratsiooni väljastamise koht ja kuupäev Vakuutuksen paikka ja päivämäärä Lieu et date de la déclaration
Ort und Datum der Erklärung Τόπος και ημερομηνία δήλωσης A nyilatkozat kelte (hely és idő) Luogo e data della dichiarazione
Deklarācijas vieta un datums Deklaracijos vieta ir data Il-post u d-data tad-dikjarazzjoni
Miejsce i data wystawienia deklaracji Local e data da
declaração Locul şi data declaraţiei Miesto a dátum vyhlásenia Kraj in datum izjave Lugar y fecha de la declaración Plats och datum för
deklarationen
Jacobsen, A Textron Company
11524 Wilmar Blvd.
Charlotte, NC 28273, USA
February 5th, 2014
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to
compile the technical file, and who is established in the Community.
Подпис на човека, упълномощен да състави декларацията от името на производителя, който поддържащ техническата документация и е
оторизиран да изготви техническия файл и е регистриран в общността.
Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávněné sestavit technické soubory a založené v
rámci Evropského společenství.
Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til
at udarbejde den tekniske journal, og som er baseret i nærområdet.
Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het
technische bestand samen te stellen, en die is gevestigd in het Woongebied.
Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus
koostada tehniline toimik.
Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan
tekniset asiakirjat ja joka on sijoittautunut yhteisöön.
Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et
qui est implantée dans la Communauté.
Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen a
ufbewahrt und berechtigt
ist, die technischen Unterlagen zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.
Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του κατασκευαστή, ο οποίος κατέχει την τεχνική έκθεση και έχει την
εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και ο οποίος είναι διορισμένος στην Κοινότητα.
A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszaki dokumentációt őrzi, engedéllyel rendelkezik a
műszaki fájl összeállításához, és aki a közösségben letelepedett személy.
Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire
il fascicolo tecnico, che deve essere stabilita nella Comunità.
Tās personas paraksts, kura ir pilnvarota deklarācijas sastādīšanai ražotāja vārdā, kurai ir tehniskā dokumentācija, kura ir pilnvarota sagatavot tehnisko
reģistru un kura ir apstiprin
āta Kopienā.
Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašė, turi visą techninę informaciją ir yra
įgaliotas sudaryti techninės informacijos dokumentą.
Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl
tekniku u li hija stabbilita fil-Komunità.
Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentację techniczną, upoważnioną do stworzenia
dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.
Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar
o processo técnico e que está estabelecida na Comunidade.
Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze
dosarul tehnic şi este stabilită în Comunitate.
Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovať technické podklady a ktorá
je umiestnená v Spoločenstve.
Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in lahko sestavlja spis tehnične dokumentacije, ter ima
sedež v Skupnosti.
Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el
archivo técnico y que está establecido en la Comunidad.
Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att
sammanställa den tekniska informationen och som är etablerad i gemenskapen.
2006/42/EC Annex II 1.A.2
Tim Lansdell
Technical Director
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, IP3 9TT, England
2006/42/EC Annex II 1.A.10
Vasant Godhalekar
VP of Engineering
Jacobsen, A Textron Company
11524 Wilmar Blvd,
Charlotte, NC 28273, USA
Certificate Number Номер на сертификат Číslo osvědčení Certifikatnummer Certificaatnummer Sertifikaadi number Hyväksyntänumero
Numéro de certificat Bescheinigungsnummer Αριθμός Πιστοποιητικού Hitelesítési szám Numero del certificato Sertifikāta numurs
Sertifikato numeris Numru taċ-Ċertifikat Numer certyfikatu Número do Certificado Număr certificat Číslo osvedčenia Številka certifikata
Número de certificado Certifikatsnummer
4160165 Rev B
4 DECALS
10
4 DECALS
4.1 DECALS _________________________________________________________________
Familiarize yourself with the following decals. They are critical to the safe operation of the
machine. REPLACE DAMAGED DECALS IMMEDIATELY.
4181865
4181864
• Read operator's manual. Do not allow untrained
operators to use machine.
• Keep shields in place and hardware securely
fastened.
• Keep hands, feet, and clothing away from moving
parts.
• Before you clean, adjust, or repair this equipment,
disengage all drives, engage parking brake, and stop
engine.
• Never carry passengers.
• Keep bystanders away.
• Do not use on slopes greater than 20°.
Danger
To avoid injury when working with battery:
1. Always connect the black (-) ground last and remove it
first.
2. Keep sparks and flames away, and avoid contact with
acid.
To avoid injury when jumping battery:
1. Connect positive (+) terminal to positive (+) terminal.
2. Connect negative (-) terminal on good battery to frame
of vehicle that has dead battery.
DECALS 4
11
Familiarize yourself with the following decals. They are critical to the safe operation of the
machine. REPLACE DAMAGED DECALS IMMEDIATELY.
4181862
4181861
4181860
4182520
WARNING
Radiator is under pressure. Remove
cap slowly to avoid personal injury.
IMPORTANT
DO NOT USE STARTING ASSIST FLUIDS
Use of starting assist fluids in the air intake system may be
potentially explosive or cause a "runaway" engine condition. This
could result in serious engine damage.
WARNING
Read mower manuals before operating or
performing any maintenance.
DANGER
To prevent injury, disengage all drives,
engage parking brake, stop engine, and
remove key before working on machine or
emptying grass catchers.
4 DECALS
12
.
3008521
3008004
4181863
WARNING
To prevent cuts use socket
wrench or Turf Groomer
®
knob to turn reel.
Traction Pedal
Reverse Forward
Engaged
Parking Brake
Disengaged
Sound Power
Level
CONTROLS 5
13
5 CONTROLS
5.1 ICONS ___________________________________________________________________
WARNING
Never attempt to drive the mower unless you have read the Safety and Operation Manual
and know how to operate all controls correctly.
Familiarize yourself with the icons shown above and what they represent. Learn the
location and purpose of all of the controls and gauges before operating this mower.
Coolant
Temperature
D
Read Manual Engine Throttle
High Low
Hour Meter
Traction Pedal
Forward Reverse
Fuel
Diesel
Cutting Units
Forward Off Reverse
(Cut) (Backlap)
Horn
Engine
Off Run Glow Plug Start
Engine Oil
Pressure
Parking Brake
Engaged Disengaged
LightsMowers
Lower Raise
Hydraulic
Oil Level
!
5 CONTROLS
14
10
12
14
16
A Tilt Steering Lever
B1 Parking Brake Lock
B2 Parking Brake Release
C Parking Brake Pedal
D Mow Speed Stop
E Traction Pedal - Forward
F Traction Pedal - Reverse
G Seat Adjustment
H Hydraulic Oil Cap
I Hydraulic Oil Light
J Fuel Cap
K Fuel Level Gauge
L Backlap Switch
M Hour Meter
N Water Temperature Gauge
O Volt Meter
P Engine Oil Pressure Light
Q Horn
R 2WD / 4WD Switch
S Raise / Lower Joystick
T Reel Switch
U Light Switch
V Ignition Switch
W Throttle
X Parking Brake Light
Y Fuse Blocks
Z Horn Switch
A
B
1
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
B
2
I
Z
CONTROLS 5
15
5.2 CONTROL DESCRIPTIONS __________________________________________________
A. Tilt Steering Lever
Pull lever up to release steering column. Tilt column
up or down to position desired. Release lever to lock
steering column in place.
B. Parking Brake Lock / Release
To lock parking brake, hold brake pedal (C) down and
press lock (B
1
) until it engages. To disengage, press
brake pedal release (B
2
).
C. Parking Brake Pedal
To engage parking brake, press pedal down.
D. Mow Speed Stop
Limits forward speed while mowing. To operate at
lower travel speed while mowing, rotate lever so it
contacts stop screw (D1) on floor board when
forward travel pedal is pressed. To travel at full
speed, set lever in position shown (D3). Stop screw
(D2) can be adjusted to set specific mow speeds.
See the Parts & Maintenance manual.
Figure 5A
E. Traction Pedal Forward Travel
Press front of pedal down for forward travel. Release
pedal to slow mower and stop. Do not press traction
pedal when parking brake is set and parking brake light
(X) is lit.
F. Traction Pedal Reverse Travel
Press rear of pedal down for reverse travel. Release
pedal to slow mower and stop. Allow mower to come to
a complete stop before reversing directions. Do not
press traction pedal when parking brake is set and
parking brake light (X) is lit.
G. Seat Adjustment
Pull left side lever out to adjust seat forward or
backward. To adjust spring tension under seat, turn
adjusting knob on front of seat.
H. Hydraulic Oil Cap
Fill to “green” area on gauge using clean hydraulic fluid
while machine is cool. Do not overfill.
I. Hydraulic Oil Light
Alerts the operator of a low fluid level in
hydraulic tank. This light operates in
combination with the alarm. See Section 5.3.
J. Fuel Cap
Remove cap to fill fuel tank with clean, fresh, #2 low or
ultra low sulfur diesel fuel, minimum Cetane Rating of
45. See Section 6.10.
K. Fuel Level Gauge
Indicates current fuel level. Check fuel gauge daily
before starting machine.
Fill only to “green” area on
gauge; do not top off tank.
Do not allow machine to run
out of fuel.
L. Backlap Switch
The backlap switch allows the mowers to rotate in
reverse for backlapping.
Forward - For normal operation (mowing) the
switch must be set to the FORWARD (cut)
position.
Reverse - When backlapping, the mowers must
be operated in the reverse direction. Set switch
to the REVERSE (backlap) position.
When backlapping, the parking brake must be set and
both the reel switch (T) and backlap switch (L) must be
set to reverse. See Parts & Maintenance Manual.
M. Hour Meter
Records engine operating hours. Use hour meter to
schedule periodic maintenance.
N. Water Temperature Gauge
Indicates engine coolant temperature. Normal operating
temperature should be between 160° - 230°F (71°-
110°C). If temperature rises above 230°F (110°C),
alarm will sound. See Section 5.3.
O. Volt Meter
Indicates battery condition. During normal operation
meter should never be in the red area.
CAUTION
Never adjust steering while mower is moving. Stop
unit and set parking brake before adjusting.
!
Full Speed Reduced Speed
D
1
D
2
D
3
E
F
5 CONTROLS
16
P. Engine Oil Pressure Light
The indicator will light if engine oil pressure drops
below 7 PSI (0.48 BAR). Stop engine immediately,
determine the cause, and correct the problem before
resuming operation.
Q. Horn
The alarm sounds to alert the operator to conditions
requiring immediate attention. See Section 5.3.
R. 2 WD / 4 WD Switch
Sets mower into two or four wheel drive.
S. Raise / Lower Joystick
The joystick raises and lowers the mowers. Push
forward to lower mowers, pull back to raise mowers.
T. Reel Switch
The reel switch is a 3-position rocker type switch with a
neutral locking tab. It sets the mowers for either forward
or reverse rotation. Set mower switch in its OFF (center)
position when starting the mower.
Forward - To mow, press switch to the
FORWARD (cut) position. With the switch in this
position, mowers will start automatically when
they are lowered and stop when they are raised. Return
switch to its center position to disable mowers.
Reverse - The mower can be operated in the
reverse direction for backlapping, running
vertical mowers, removing grass build-up in
mowers, or dislodging objects binding mowers. To
reverse blade rotation, press switch to the REVERSE
position.
When backlapping, the parking brake must be set,
traction pedal in neutral, and both the reel switch (T)
and backlap switch (L) must be set to REVERSE. See
Parts & Maintenance Manual.
U. Light Switch
Controls operation of work lights.
V. Ignition Switch
The ignition switch has four positions. OFF - RUN -
GLOW PLUG - START. See Section 6.4.
W. Throttle
Controls engine speed. Run machine at full throttle
during normal machine operation.
X. Parking Brake Light
Indicates that the parking brake is engaged. Parking
brake must be disengaged before depressing traction
pedal.
Y. Fuse Blocks
Used to provide circuit protection for electrical
systems. See Parts & Maintenance Manual.
Z. Horn Switch
This switch is used to test the alarm system or disable
the alarm after a low oil level has been detected. Keep
switch in its ON position when starting and operating
mower. To test alarm, set switch to OFF and turn
ignition key to RUN. See
Section 5.3.
CONTROLS 5
17
5.3 OPERATOR ALERTS _______________________________________________________
The machine monitors vital machine systems. It uses an
audible alarm and warning lights to alert the operator of
conditions requiring immediate action. When an alert
occurs, follow the general guidelines listed in the chart below
and any specific actions outlined by the grounds
superintendent or service manager.
To test alarm system:
Turn ignition switch to RUN. Engine oil light will come on for
one second or more.
This system monitors:
1. Engine oil pressure.
2. Engine coolant temperature.
3. Hydraulic oil level.
Alert Action
1. Engine Oil Pressure - Oil pressure
light comes on. Oil pressure low.
Stop mower immediately, lower implements and shut off engine! Inspect oil
level in engine. If oil light remains on with oil at proper level, shut off engine and
tow or trailer mower back to a service area. NEVER operate engine with oil light
on, severe damage to the engine can occur.
2. Engine Coolant Temperature
Alarm sounds. Engine coolant
temperature high.
Stop mower immediately, lower implements and shut off engine! Remove
debris such as leaves and grass clippings that may be restricting air flow through
front screen and area between radiator and oil cooler. If engine continues to run
hot, return mower to a service area.
CAUTION: Engine coolant is under pressure. Turn engine off and allow
fluid to cool before checking fluid level or adding coolant to radiator.
3. Hydraulic fluid level - alarm
sounds and hydraulic fluid
warning light comes on.
Hydraulic fluid is below
recommended level.
Stop mower immediately, lower implements and shut off engine! Visually
inspect mower for obvious signs of leaks around connections, hoses and
hydraulic components. Return mower to service area for maintenance.
CAUTION: Hydraulic fluid is under pressure. Turn engine off and allow fluid
to cool before checking fluid level or adding oil to hydraulic tank.
6 OPERATION
18
6 OPERATION
6.1 DAILY INSPECTION________________________________________________________
1. Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and missing or
damaged components. Check for fuel or oil leaks to
ensure connections are tight and hoses and tubes
are in good condition.
2. Check the fuel supply, radiator coolant level,
crankcase oil, and air cleaner indicator. All fluids
must be at the full level mark with engine cold.
3. Make sure all mowers are adjusted to the same
cutting height.
4. Check tires for proper inflation.
5. Test the Interlock System.
Note: For more detailed maintenance information,
adjustments and maintenance/lube charts, see the
Parts & Maintenance manual.
6.2 INTERLOCK SYSTEM ______________________________________________________
1. The Interlock System prevents the engine from
starting unless the parking brake is engaged, the
traction pedal is in neutral, and the reel switch is OFF.
The system also stops the engine if the operator
leaves the seat with the reel switch ON, traction
pedal out of NEUTRAL, or parking brake
DISENGAGED.
2. Perform each of the following tests to insure the
Interlock System is functioning properly. Stop the
test and have the system inspected and repaired if
any of the tests fail as listed below:
the engine does not start in test 1;
the engine does start during tests 2, 3 or 4;
the engine continues to run during tests 5 or 6.
3. Refer to the chart below for each test and follow the
check (
) marks across the chart. Shut engine off
between each test.
Test 1: Represents normal starting procedure. The
operator is seated, parking brake is engaged, the
traction pedal is in neutral, and the reel switch is OFF.
The engine should start.
Test 2: The engine must not start if the reel switch is
ON.
Test 3: The engine must not start if the parking brake
is DISENGAGED.
Test 4: The engine must not start if traction pedal is
not in neutral.
Test 5: Start the engine in the normal manner then
turn reel switch ON and lift your weight off the seat.
Test 6: Start the engine in the normal manner then
disengage parking brake and lift your weight off the
seat.
Lift your weight off seat. The engine will shut down.
CAUTION
The daily inspection should be performed only when
the engine is off and all fluids are cold. Lower mowers
to the ground, engage the parking brake, stop engine,
and remove ignition key.
!
WARNING
Never operate equipment with the Interlock
System disconnected or malfunctioning. Do not
disconnect or bypass any switch.
!
Interlock System Check
Test Operator
Seated
Parking
Brake
Traction Pedal
in Neutral
Reel
Switch
Engine
Starts
Yes No Engaged Disengaged Yes No On Off Yes No
1 
2 
3 
4 
5

6

OPERATION 6
19
6.3 OPERATING PROCEDURES _________________________________________________
1. Under no circumstances should the engine be
started without the operator seated on the mower.
2. Do not operate mower or attachments with loose,
damaged, or missing components. Whenever
possible mow when grass is dry.
3. First mow in a test area to become thoroughly
familiar with the operation of the mower and control
levers.
Never operate the reels unless they are mowing
grass. Heat will develop between the bedknife and
reel and damage the cutting edge.
4. Study the area to determine the best and safest
operating procedure. Consider the height of the
grass, type of terrain, and condition of the surface.
Each condition will require certain adjustments or
precautions.
5. Never direct discharge of material toward
bystanders, nor allow anyone near the machine
while in operation. The owner/operator is
responsible for injuries inflicted to bystanders and/or
damage to their property.
6. Use discretion when mowing near gravel areas
(roadway, parking areas, cart paths, etc.). Stones
discharged from the implement may cause serious
injuries to bystanders and/or damage the
equipment.
7. Always turn reel switch off to stop blades when not
mowing.
8. Disengage the drive motors and raise the reels
when crossing paths or roadways. Look out for
traffic.
9. Stop and inspect the equipment for damage
immediately after striking an obstruction or if the
machine begins to vibrate abnormally. Have the
equipment repaired before resuming operation.
10. Slow down and use extra care on hillsides. Read
Section 6.7. Use caution when operating near drop
offs.
11. Look behind and down before backing up to be sure
the path is clear. Use care when approaching blind
corners, shrubs, trees, or other objects that may
obscure vision.
12. Never use your hands to clean cutting units. Use a
brush to remove grass clippings from blades. Blades
are extremely sharp and can cause serious injuries.
WARNING
A Roll Over Protection Structure (ROPS) is included with this mower. Seat belts must be worn whenever operating
a mower with a ROPS. Always keep seat belt snugly adjusted. DO NOT use seat belts on a mower without a ROPS.
If the mower is overturning, hold onto the steering wheel. Do not attempt to jump out or leave the seat.
!
CAUTION
To prevent injury, always wear safety glasses, leather work shoes or boots, a hard hat, and ear protection.
!
CAUTION
Before mowing, pick up all debris such as rocks, toys,
and wire which can be thrown by the machine. Enter a
new area cautiously. Always operate at speeds that
allow you to have complete control of the mower.
!
WARNING
Before you clean, adjust, or repair this equipment,
always disengage all drives, lower implements to
the ground, engage parking brake, stop engine,
and remove key from ignition switch to prevent
injuries.
!
6 OPERATION
20
6.4 STARTING _______________________________________________________________
IMPORTANT: Do not use starting assist fluids. Use of
such fluids in the air intake system may be potentially
explosive or cause a “Runaway” engine condition and
could result in serious engine damage.
1. Make sure fuel shut off valve is completely open and
the tow valve (See Section 6.9) is closed.
2. Sit in operator’s seat, make sure reel switch (T) is
OFF, parking brake (C) is engaged, and traction
pedal (E and F) is in neutral.
3. Move throttle lever between 1/8 to 1/2 throttle (W).
Turn ignition switch (V) to RUN. Parking brake light
(X) and engine oil light (P) should be lit.
4. Turn ignition switch to GLOW PLUG position for
about 3 to 5 seconds, then turn key to START
position. Release as soon as engine starts. The
colder the temperature, the longer it will take to
energize plugs. Do not hold switch in GLOW PLUG
position for more than 5 seconds, or in the START
position for more than 15 seconds. Energizing glow
plugs is not necessary when starting a warm
engine. Once engine starts, engine oil light (P)
should go out.
5. Allow the engine to become warm and properly
lubricated before operating at high RPM.
Figure 6A
6.5 STOPPING / PARKING _____________________________________________________
To stop:
Remove your foot from traction pedal. The mower will
automatically brake when the traction pedal returns to
neutral.
To park the mower under normal conditions:
1. Disengage the reel switch, raise the implements, and
move away from the area of operation.
2. Select a flat and level area to park.
a. Release traction pedal to bring the mower to a
complete stop.
b. Disengage all drives, lower implements to the
ground, reduce throttle to slow, and allow engine
to operate at no load for several minutes.
3. Engage parking brake, stop the engine, and always
remove the ignition key.
If an emergency arises and the mower must be parked in
the area of operation, follow the guidelines outlined by
the grounds superintendent. If the mower is parked on an
incline, chock or block the wheels.
10
12
14
16
V
T
W
P
X
NOTICE
Permanent damage to the turbocharger may occur if
the engine is shut down without allowing the
turbocharger time to cool.
To prevent damage, operate the engine with no load
and at half throttle for 3 to 5 minutes before shutting
off engine.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

Jacobsen 67955, 67956, 67957, 68007, 68008 Omaniku manuaal

Kategooria
Muruniidukid
Tüüp
Omaniku manuaal
See käsiraamat sobib ka