Hilti TE 3000-AVR Kasutusjuhend

TE 3000-AVR

English 1

Français 12

Dansk 23

Svenska 33

Norsk 43

Suomi 53

Eesti 63

Latviešu 73

Lietuvių 83

Русский 94

Українська 106

Қазақ 117

Türkçe 128

ﻋﺮﺑﻲ 139

日本語 150

한국어 160

繁體中文 169

中文 178

1

2

3

4

TE 3000-AVR

en Originaloperatinginstructions....................................... 1

fr Noticed'utilisationoriginale ....................................... 12

da Originalbrugsanvisning .......................................... 23

sv Originalbruksanvisning........................................... 33

no Originalbruksanvisning .......................................... 43

fi Alkuperäisetohjeet ............................................. 53

et Originaalkasutusjuhend .......................................... 63

lv Oriģinālālietošanasinstrukcija ..................................... 73

lt Originalinaudojimoinstrukcija...................................... 83

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 94

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

tr Orijinalkullanımkılavuzu ......................................... 128

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 139

ja オリジナル取扱説明書 ............................................ 150

ko 오리지널사용설명서............................................. 160

zh 原始操作說明.................................................. 169

cn 原版操作说明.................................................. 178

*2190685* 2190685 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

1.3 Symbols on the product

1.3.1 Symbols on the product

The following symbols can be used on the product:

2 English 2190685 *2190685*

Protection class II (double-insulated)

Transport by crane is not permissible

Wireless data transfer

1.4 Product information

Hilti products are designed for professional use and may be operated, serviced and maintained only by

trained, authorized personnel. This personnel must be informed of any particular hazards that may be

encountered. The product and its ancillary equipment may present hazards when used incorrectly by

untrained personnel or when used not as directed.

The type designation and serial number are printed on the type identification plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to enquire about the product.

Product information → page 2

Product information

Breaker TE 3000AVR

Generation 01

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

*2190685* 2190685 English 3

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

2.2 Hammer safety warnings

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handles, if supplied with the tool. Loss of control can cause personal injury.

▶Hold power tool by insulated gripping surfaces, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and could give the operator an electric shock.

2.3 Additional safety instructions

Personal safety

▶Use the tool only when it is in technically faultless condition.

▶Never tamper with or modify the tool in any way.

▶Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶Check that the side handle is fitted correctly and tightened securely. Always hold the tool securely with

both hands on the grips provided. Keep the grips dry, clean and free from oil and grease.

4 English 2190685 *2190685*

▶Take breaks between working and do physical exercises to improve the blood circulation in your fingers.

Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous

system in the fingers, hands and wrists.

▶The tool is not intended for use by debilitated persons who have received no special training.

▶Keep the power tool out of reach of children.

▶Before beginning the work, check the hazard classification of the dust that will be produced. Use an

industrial vacuum cleaner with an officially approved protection classification in compliance with locally

applicable dust protection regulations.

▶Use a dust removal system and suitable vacuum cleaner whenever possible. Dust from materials, such

as paint containing lead, some wood species, concrete/masonry/stone containing silica, and minerals as

well as metal, may be harmful.

▶Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as

carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing asbestos may be handled only by specialists.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

You may receive an electric shock from external metal parts of the power tool if you damage an electric

cable accidentally.

▶Check the power tool’s supply cord at regular intervals and have it replaced by a qualified specialist if

found to be damaged. If the power tool’s supply cord is damaged it must be replaced with a specially-

prepared and approved supply cord available from Hilti Customer Service. Check extension cords at

regular intervals and replace them if found to be damaged. Do not touch the supply cord or extension

cord if it is damaged while working. Disconnect the supply cord plug from the power outlet. Damaged

supply cords or extension cords present a risk of electric shock.

▶Dirty or dusty power tools that have been used frequently for work on conductive materials should be

checked at regular intervals at a Hilti Service Center. Dust (especially dust from conductive materials) or

dampness adhering to the surface of the tool may, under unfavorable conditions, lead to electric shock.

▶Switch the power tool off and unplug the supply cord in the event of a power failure or interruption in the

electric supply. This will prevent accidental restarting when the electric power returns.

*2190685* 2190685 English 5

3 Description

3.1 Overview of the product 1

@On/off switch

;Service indicator

=Grip

%Air vents

&Guide tube

(Accessory tool retainer / locking bar

)Chuck

+Supply cord with keyed, releasable plug con-

nector

§Connector on electric tool

6 English 2190685 *2190685*

3.2 Transport trolley components 2

@Grip

;Locking bar

=Holder for accessory tools (chisels)

%Wheels

&Wheel securing parts (washer, retaining pin)

(Power tool locating pin

3.3 Intended use

The product described is a hand-held electric breaker with 28 mm hex chuck. It is designed for chiseling

work on concrete, masonry and asphalt. Excavation and compacting are further possible applications.

▶Operation is permissible only when connected to a power source providing a voltage and frequency in

compliance with the information given on the type identification plate.

3.4 Possible misuse

This product is not suitable for working on hazardous materials.

This product is not suitable for working in a damp environment.

3.5 Service indicator

The breaker is equipped with a service indicator LED.

Status Meaning

The service indicator lights red. End of service interval – servicing is due.

A fault has occurred in the tool.

The service indicator blinks red. Protection against overheating

The voltage provided by the electric supply is too

high.

Bring the product to Hilti Service in good time. This will help to ensure that it’s always ready for use.

3.6 Active Vibration Reduction (AVR)

The breaker is equipped with an Active Vibration Reduction (AVR) system, which reduces vibration

significantly.

*2190685* 2190685 English 7

3.7 Items supplied

Electric breaker, operating instructions, grease.

The transport trolley is available as an accessory.

You can find other system products approved for your product at your local Hilti Center or online at:

www.hilti.group

4 Technical data

For details of the rated voltage, current, frequency and/or input power, please refer to the power tool’s

country-specific type identification plate.

When powered by a generator or transformer, the generator or transformer’s power output must be at least

twice the rated input power shown on the rating plate of the power tool. The operating voltage of the

transformer or generator must always be within +5% and -15% of the rated voltage of the power tool.

TE 3000AVR

Weight in accordance with EPTA proce-

dure 01 29.9 kg

Single impact energy in accordance with

the EPTA procedure 68 J

Storage temperature −20 ℃ … 70 ℃

Ambient temperature for operation −17 ℃ … 60 ℃

4.1 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions have been measured in accordance with

a standardized test and may be used to compare one power tool with another. They may be used for a

preliminary assessment of exposure.

The data given represents the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools or is poorly maintained, the data may vary. This may

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the power tool is switched

off, or when it is running but not actually being used for a job. This may significantly reduce exposure over

the total working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: Maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise information

Sound (power) level (LWA)105 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A)

Sound pressure level (LpA)94 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A)

Vibration information

Chiseling (ah, Cheq)7 m/s²

Uncertainty (K) 1.5 m/s²

4.2 Using extension cords

WARNING

A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged

while working. Disconnect the supply cord plug from the power outlet.

▶Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if

found to be damaged.

8 English 2190685 *2190685*

• Use only extension cords of a type approved for the application and with conductors of adequate gauge

(cross section). The power tool may otherwise suffer a drop in performance and the extension cord may

overheat.

• Check the extension cord for damage at regular intervals.

• Replace damaged extension cords.

• When working outdoors, use only extension cords that are approved and correspondingly marked for

this application.

Recommended minimum conductor cross-section and maximum power-cord length for 120V supply

voltage

Cord AWG 16 AWG 14 AWG 12 AWG 10

Conductor cross-section 1,31 mm² 2,08 mm² 3,31 mm² 5,26 mm²

Conductor cross-section 2,58 kcmil 4,11 kcmil 6,53 kcmil 10,4 kcmil

Cord length 25 m 30 m 50 m 100 m

Cord length 75 ft 100 ft 150 ft 250 ft

5 Operation

5.1 Preparations at the workplace

CAUTION

Risk of injury! Inadvertent starting of the product.

▶Unplug the supply cord before making adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1.1 Fitting the accessory tool 3

Check the accessory tool for damage or uneven wear each time before use and replace it if necessary.

Check that the locking bar is clean and undamaged.

1. Apply a little grease to the connection end of the accessory tool.

2. Open the locking bar.

3. Push the accessory tool into the chuck as far as it will go.

4. For accessory tools with a collar, bring the retaining bar into locking position A.

5. For accessory tools with a locking groove, bring the retaining bar into locking position B.

➥ Position the chisel so that the groove is facing locking position B.

6. Check that the chisel has engaged correctly by gripping and pulling it.

➥ Insert tools with a combined connection end (with collar and groove) can be locked in position A or

B, as desired.

Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage

to the product.

5.1.2 Removing the accessory tool 4

WARNING

Risk of injury! The accessory tool gets hot during use and may also have sharp edges.

▶Wear protective gloves when changing the tool.

DANGER

Risk of fire! Risk of contact between the hot accessory tool and highly inflammable materials.

▶Do not lay the hot accessory tool down on highly inflammable materials.

WARNING

Risk of injury! Risk of burning injuries caused by hot surfaces.

▶Avoid touching the guide tube as this part gets hot through use of the power tool.

*2190685* 2190685 English 9

1. Open the locking bar.

2. Pull the accessory tool out of the chuck.

5.2 Detachable supply cord

CAUTION

Risk of injury! Due to leakage current as a result of dirty contacts.

▶Connect the detachable electric connector to the electric tool only when it is clean and dry and when the

supply cord is unplugged from the power outlet.

▶Connect / disconnect the detachable supply cord.

5.2.1 Connecting the detachable supply cord

CAUTION

Risk of injury! Due to leakage current as a result of dirty contacts.

▶Connect the detachable electric connector to the electric tool only when it is clean and dry and when the

supply cord is unplugged from the power outlet.

1. Push the keyed, detachable electric plug connector into the socket as far as it will go, until it is heard to

engage.

2. Plug the supply cord into the power outlet.

5.2.2 Disconnecting the detachable supply cord

1. Unplug the supply cord from the power outlet.

2. Press the release button and pull the keyed, detachable electric plug connector out of the socket.

3. Pull the supply cord connector out of the power tool.

6 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

7 Transport and storage

• Do not transport electric tools with accessory tools fitted.

• Always unplug the supply cord before storing an electric tool or appliance.

10 English 2190685 *2190685*

• Store tools and appliances in a dry place where they cannot be accessed by children or unauthorized

persons.

• Check electric tools or appliances for damage after long periods of transport or storage.

8 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

8.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The breaker doesn’t start. Electronics initialization in progress

(takes up to 4 seconds after plug-

ging in). The electronic restart in-

terlock is activated after an inter-

ruption in the electric supply.

▶Switch the power tool off and

then on again.

Interruption in the electric supply. ▶Plug in another electric tool or

appliance and check whether it

works.

The generator is in sleep mode. ▶Apply a load to the generator

by connecting a second power

consumer (e.g. worklight).

Switch the tool off and then on

again.

The detachable supply cord is not

fitted correctly.

▶Fit the detachable supply cord

to the power tool correctly.

The service indicator lights

red. The tool is faulty or servicing is

due.

▶Have the product repaired only

by Hilti Service.

The service indicator blinks

red. The voltage provided by the elec-

tric supply is too high.

▶Use a different power outlet.

Check the electric supply.

The overheating prevention cut-out

has been activated.

▶Allow the tool to cool down.

Clean the air vents. Running

under no load is still possible.

No hammering action. The power tool is too cold. ▶Bring the tip of the accessory

tool into contact with the

working surface, switch the

power tool on and allow it to

run. If necessary, repeat the

procedure until the hammering

mechanism begins to operate.

The breaker doesn’t start or

cuts out during operation. The extension cord is too long or

its gauge is inadequate.

▶Use an extension cord of an

approved length and / or of

adequate gauge.

9 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

10 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances: qr.hilti.com/r4783.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

*2190685* 2190685 English 11

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

12 Français 2190685 *2190685*

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service. C'est la condition préalablement

requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que

celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement le transmettre à des tiers

avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

DANGER

DANGER !

▶Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

ATTENTION

ATTENTION !

▶Pour attirer l'attention sur une situation pouvant présenter des dangers entraînant des blessures

corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans l'image et peut se différencier

de celles des étapes de travail dans le texte

Les numéros de position sont utilisés dans l'illustration Vue d’ensemble et renvoient aux numé-

ros des légendes dans la section Vue d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement attention.

1.3 Symboles sur le produit

1.3.1 Symboles sur le produit

Les symboles suivants peuvent être utilisés sur le produit :

*2190685* 2190685 Français 13

Classe de protection II (double isolation)

Transport par pont roulant ou grue interdit

Transmission de données sans fil

1.4 Informations produit

Les produits Hilti sont conçus pour les utilisateurs professionnels et ne doivent être utilisés, entretenus et

réparés que par un personnel agréé et formé à cet effet. Ce personnel doit être au courant des dangers

inhérents à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont

utilisés de manière incorrecte par un personnel non qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque signalétique.

▶Inscrivez le numéro de série dans le tableau suivant. Les informations produit vous seront demandées

lorsque vous contactez nos revendeurs ou services après-vente.

Caractéristiques produit → Page 13

Caractéristiques produit

Burineur TE 3000AVR

Génération 01

N° de série

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit décrit ici est conforme aux

directives et normes en vigueur. Une copie de la Déclaration de conformité se trouve en fin de la présente

documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sécurité

2.1 Indications générales de sécurité pour les outils électriques

AVERTISSEMENT Lire et comprendre toutes les consignes de sécurité et instructions. Tout

manquement à l'observation des consignes de sécurité et instructions risque de provoquer une électrocution,

un incendie et/ou de graves blessures.

Les consignes de sécurité et instructions doivent être intégralement conservées pour les utilisations

futures.

La notion d'« outil électroportatif » mentionnée dans les consignes de sécurité se rapporte à des outils

électriques raccordés au secteur (avec câble de raccordement) et à des outils électriques sur accu (sans

câble de raccordement).

Sécurité sur le lieu de travail

▶Conserver la zone de travail propre et bien éclairée. Un lieu de travail en désordre ou mal éclairé

augmente le risque d'accidents.

▶Ne pas faire fonctionner les outils électriques en atmosphère explosive et où se trouvent des

liquides, des gaz ou poussières inflammables. Les outils électriques produisent des étincelles qui

peuvent enflammer les poussières ou les fumées.

▶Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil électro-

portatif. En cas d'inattention il y a risque de perdre le contrôle de l'appareil.

Sécurité relative au système électrique

▶La fiche de secteur de l'outil électroportatif doit être adaptée à la prise de courant. Ne jamais

modifier la fiche de quelque façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils

électriques à branchement de terre. Des fiches non modifiées et des prises de courant adaptées

réduiront le risque de choc électrique.

▶Éviter le contact physique avec des surfaces mises à la terre tels que tuyaux, radiateurs, cuisinières

et réfrigérateurs. Il y a un risque élevé de choc électrique au cas où votre corps serait relié à la terre.

▶Ne pas exposer les outils électroportatifs à la pluie ou à l'humidité. La pénétration d'eau à l'intérieur

d'un outil électroportatif augmentera le risque d'un choc électrique.

14 Français 2190685 *2190685*

▶Ne jamais utiliser le cordon à d'autres fins que celles prévues, telles que pour porter, accrocher ou

débrancher l'outil électroportatif de la prise de courant. Maintenir le cordon à l'écart de la chaleur,

des parties grasses, des bords tranchants ou des parties de l'appareil en mouvement. Des cordons

endommagés ou emmêlés augmentent le risque de choc électrique.

▶Si l'outil électroportatif est utilisé à l'extérieur, utiliser uniquement une rallonge homologuée pour

les applications extérieures. L'utilisation d'une rallonge électrique homologuée pour les applications

extérieures diminue le risque d'un choc électrique.

▶Si l'utilisation de l'outil électrique dans un environnement humide ne peut pas être évitée, utiliser

un interrupteur de protection contre les courants de court-circuit. L'utilisation d'un tel interrupteur

de protection réduit le risque d'une décharge électrique.

Sécurité des personnes

▶Rester vigilant, surveiller ce que l'on fait. Faire preuve de bon sens en utilisant l'outil électroportatif.

Ne pas utiliser l'outil électroportatif si vous êtes fatigué ou sous l'emprise de l'alcool, de drogues

ou de médicaments. Un moment d'inattention lors de l'utilisation de l'outil électroportatif peut entraîner

des blessures graves.

▶Utiliser un équipement de sécurité et toujours porter une protection pour les yeux. Les équipements

de protection personnels tels que masque antipoussière, chaussures de sécurité antidérapantes, casque

de protection ou protection acoustique suivant l'utilisation de l'outil électroportatif, réduiront le risque de

blessures des personnes.

▶Éviter une mise en service par mégarde. S'assurer que l'outil électroportatif est arrêté avant de le

brancher à la source de courant et/ou à l'accu, de le prendre ou de le porter. Le fait de porter l'outil

électroportatif avec le doigt sur l'interrupteur ou de brancher l'appareil sur la source de courant lorsque

l'interrupteur est en position de fonctionnement peut entraîner des accidents.

▶Retirer tout outil de réglage ou toute clé avant de mettre l'outil électroportatif en fonctionnement.

Une clé ou un outil se trouvant sur une partie en rotation peut causer des blessures.

▶Adopter une bonne posture. Veiller à toujours garder une position stable et équilibrée. Cela permet

un meilleur contrôle de l'outil électroportatif dans des situations inattendues.

▶S'habiller de manière adaptée. Ne pas porter de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à distance des parties en mouvement. Des vêtements amples,

des bijoux ou des cheveux longs peuvent être happés par des parties en mouvement.

▶Si des dispositifs servant à aspirer ou à recueillir les poussières doivent être utilisés, s'assurer

qu'ils sont effectivement raccordés et correctement utilisés. L'utilisation d'un dispositif d'aspiration

de la poussière peut réduire les risques dus aux poussières.

Utilisation et maniement de l'outil électroportatif

▶Ne pas forcer l'appareil. Utiliser l'outil électroportatif adapté au travail à effectuer. Un outil

électroportatif approprié réalisera mieux le travail et de manière plus sûre au régime pour lequel il a été

conçu.

▶Ne pas utiliser d'outil électroportatif dont l'interrupteur est défectueux. Tout outil électroportatif qui

ne peut plus être mis en ou hors fonctionnement est dangereux et doit être réparé.

▶Débrancher la fiche de la prise de courant et/ou l'accu avant d'effectuer des réglages sur l'appareil,

de changer les accessoires, ou de ranger l'appareil. Cette mesure de précaution empêche une mise

en fonctionnement par mégarde de l'outil électroportatif.

▶Conserver les outils électroportatifs non utilisés hors de portée des enfants. Ne pas permettre

l'utilisation de l'appareil à des personnes qui ne se sont pas familiarisées avec celui-ci ou qui n'ont

pas lu ces instructions. Les outils électroportatifs sont dangereux lorsqu'ils sont entre les mains de

personnes non initiées.

▶Prendre soin des outils électroportatifs. Vérifier que les parties en mouvement fonctionnent

correctement et qu'elles ne sont pas coincées, et contrôler si des parties sont cassées ou

endommagées de sorte que le bon fonctionnement de l'outil électroportatif s'en trouve entravé.

Faire réparer les parties endommagées avant d'utiliser l'appareil. De nombreux accidents sont dus

à des outils électroportatifs mal entretenus.

▶Garder les outils de coupe affûtés et propres. Des outils destinés à couper correctement entretenus

avec des bords tranchants bien aiguisés se coincent moins souvent et peuvent être guidés plus

facilement.

▶L'outil électroportatif, les accessoires, les outils amovibles, etc. doivent être utilisés conformément

à ces instructions. Tenir également compte des conditions de travail et du travail à réaliser.

L'utilisation des outils électroportatifs à d'autres fins que celles prévues peut entraîner des situations

dangereuses.

Leht laadib ...

Hilti TE 3000-AVR Kasutusjuhend

Hilti TE 3000-AVR Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid