Makita DCC501 Kasutusjuhend

Bränd: Makita

Mudel: DCC501

Kategooria: Nurklihvijad

Tüüp: Kasutusjuhend

DCC501

EN Cordless Cutter INSTRUCTION MANUAL 10

SV Batteridriven glas- och

kakelskärare BRUKSANVISNING 22

NO Batteridrevet kutter BRUKSANVISNING 34

FI Akkukäyttöinen leikkuri KÄYTTÖOHJE 46

DA Akku skærer BRUGSANVISNING 58

LV Bezvada frēze LIETOŠANAS INSTRUKCIJA 71

LT Belaidis pjaustytuvas NAUDOJIMO INSTRUKCIJA 83

ET Juhtmeta lõikur KASUTUSJUHEND 95

RU Аккумуляторная алмазная

пила РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 107

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

123

Fig.37

Fig.38

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

Fig.44

Fig.45

Fig.46

Fig.47

Fig.48

Fig.49

10 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DCC501

Wheel diameter 125 mm

Max. wheel thickness 2.2 mm

Max. cutting capacities 0° bevel angle 40 mm

45° bevel angle 27 mm

Rated speed (n) 8,800 min-1

Overall length 283 mm *1

Rated voltage D.C. 18 V

Net weight 2.7 - 3.0 kg

*1. With battery cartridge (BL1860B).

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /

DC18SH

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Intended use

The tool is intended for cutting in brick and concrete

with a diamond wheel and water.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745-2-22:

Sound pressure level (LpA) : 96 dB(A)

Sound power level (LWA) : 107 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60745-2-22:

Work mode: concrete cutting

Vibration emission (ah) : 4.0 m/s2

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

11 ENGLISH

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Cutter safety warnings

1. The guard provided with the tool must be

securely attached to the power tool and

positioned for maximum safety, so the least

amount of wheel is exposed towards the oper-

ator. Position yourself and bystanders away

from the plane of the rotating wheel. The guard

helps to protect operator from broken wheel frag-

ments and accidental contact with wheel.

2. Use only diamond cut-o wheels for your

power tool. Just because an accessory can be

attached to your power tool, it does not assure

safe operation.

3. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

theirratedspeedcanbreakandyapart.

4. Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-o wheel. Abrasivecut-owheels

are intended for peripheral grinding, side forces

applied to these wheels may cause them to

shatter.

5. Always use undamaged wheel anges that are

of correct diameter for your selected wheel.

Properwheelangessupportthewheelthus

reducing the possibility of wheel breakage.

6. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

7. The arbour size of wheels and anges must

properly t the spindle of the power tool.

Wheelsandangeswitharbourholesthatdonot

match the mounting hardware of the power tool

will run out of balance, vibrate excessively and

may cause loss of control.

8. Do not use damaged wheels. Before each

use, inspect the wheels for chips and cracks.

If power tool or wheel is dropped, inspect for

damage or install an undamaged wheel. After

inspecting and installing the wheel, position

yourself and bystanders away from the plane

of the rotating wheel and run the power tool

at maximum no load speed for one minute.

Damaged wheels will normally break apart during

this test time.

9. Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and shop apron capable of stopping

small abrasive or workpiece fragments. The

eyeprotectionmustbecapableofstoppingying

debris generated by various operations. The dust

maskorrespiratormustbecapableofltrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hear-

ing loss.

10. Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken wheel may

yawayandcauseinjurybeyondimmediatearea

of operation.

11. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact hid-

den wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

wheel may grab the surface and pull the power

tool out of your control.

13. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

14. Regularly clean the power tool’s air vents. The

motorʼsfanwilldrawthedustinsidethehousing

and excessive accumulation of powdered metal

may cause electrical hazards.

15. Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

12 ENGLISH

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid stall-

ing of the rotating wheel which in turn causes the uncon-

trolled power tool to be forced in the direction opposite of

the wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the material

causing the wheel to climb out or kick out. The wheel may

eitherjumptowardorawayfromtheoperator,dependingon

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

1. Maintain a rm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or kick-

back forces, if proper precautions are taken.

2. Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

3. Do not position your body in line with the

rotating wheel. Kickback will propel the tool in

direction opposite to the wheel’s movement at the

point of snagging.

4. Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

blades create frequent kickback and loss of control.

6. Do not “jam” the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases

the loading and susceptibility to twisting or binding

of the wheel in the cut and the possibility of kick-

back or wheel breakage.

7. When wheel is binding or when interrupting

a cut for any reason, switch o the power

tool and hold the power tool motionless until

the wheel comes to a complete stop. Never

attempt to remove the wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of wheel binding.

Do not restart the cutting operation in the work-

piece. Let the wheel reach full speed and carefully

re-enter the cut. The wheel may bind, walk up or

kickback if the power tool is restarted in the workpiece.

9. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

10. Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, elec-

tricalwiringorobjectsthatcancausekickback.

11. Before using a segmented diamond wheel,

make sure that the diamond wheel has the

peripheral gap between segments of 10 mm or

less, only with a negative rake angle.

Additional Safety Warnings:

1. Never attempt to cut with the tool held upside

down in a vise. This can lead to serious acci-

dents, because it is extremely dangerous.

2. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

3. Store wheels as per manufacturer recom-

mendations. Improper storage may damage the

wheels.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

13 ENGLISH

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

Important safety instructions for wireless unit

Do not disassemble or tamper with the wireless unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

Do not expose the wireless unit to rain or wet conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50°C (122°F).

Do not operate the wireless unit in places where medi-

cal instruments, such as heart pace makers are nearby.

Do not operate the wireless unit in places where

automated devices are nearby. If operated, auto-

mated devices may develop malfunction or error.

Do not operate the wireless unit in places under

high temperature or places where static electric-

ity or electrical noise could be generated.

The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the user.

10. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

14.

Always insert the wireless unit in the correct direction.

15. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

16.

Always close the lid of the slot when operating.

17.

Do not remove the wireless unit from the slot while

the power is being supplied to the tool. Doing so

may cause a malfunction of the wireless unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20.

Do not leave the wireless unit in a place where static

electricity or electrical noise could be generated.

21.

Do not leave the wireless unit in a place subject

to high heat, such as a car sitting in the sun.

22.

Do not leave the wireless unit in a dusty or powdery

place or in a place corrosive gas could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

27.

Do not use the tool with the lid of the slot damaged. Water,

dust, and dirt come into the slot may cause malfunction.

28.

Do not pull and/or twist the lid of the slot more than

necessary.Restorethelidifitcomesofromthetool.

29.

Replace the lid of the slot if it is lost or damaged.

SAVE THESE INSTRUCTIONS.

14 ENGLISH

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem.Thissystemautomaticallycutsopowertothe

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions.

Overload protection

When the tool/battery is operated in a manner that

causes it to draw an abnormally high current, the tool

automaticallystops.Inthissituation,turnthetoolo

and stop the application that caused the tool to become

overloaded. Then turn the tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops

automatically and the operation lamp will blink. In this

situation, let the tool cool down before turning the tool

on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the tool does not run along with the

switch operation, remove the battery from the tool and

charge it.

Adjusting depth of cut

CAUTION: After adjusting the depth of cut,

always tighten the lever securely.

Loosen the lever on the depth guide and move the base

up or down. At the desired depth of cut, secure the base

by tightening the lever.

For cleaner, safer cuts, set cut depth so that the dia-

mondwheelprojects2mmorlessbelowworkpiece.

Using proper cut depth helps to reduce potential for

dangerous KICKBACKS which can cause personal

injury.

►Fig.3: 1. Lever 2. Depth guide

Bevel cutting

CAUTION: After adjusting the bevel angle,

always tighten the clamping screw securely.

►Fig.4: 1. Clamping screw 2. Bevel scale plate

Loosen the clamping screw on the bevel scale plate on

the front of the base. Set for the desired angle (0° - 45°)

by tilting accordingly, then tighten the clamping screw

securely.

15 ENGLISH

Sighting

For straight cutting

Align the side edge of the base with your intended

cutting line on the workpiece.

►Fig.5: 1. Side edge of the base 2. Cutting line

For 45° bevel cutting

Align the inner edge of the guide notch in the base with

your intended cutting line on the workpiece.

►Fig.6: 1. Inner edge of the guide notch 2. Cutting

line

Switch action

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-o button. A switch in need of repair

may result in unintentional operation and serious

personalinjury.ReturntooltoaMakitaservicecenter

for proper repairs BEFORE further usage.

WARNING: NEVER defeat the lock-o button

by taping down or some other means. A switch with

anegatedlock-obuttonmayresultinunintentional

operationandseriouspersonalinjury.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: Do not pull the switch trigger hard

without pressing in the lock-o button. This can

cause switch breakage.

CAUTION: The tool starts to brake the

diamond wheel rotation immediately after you

release the switch trigger. Hold the tool rmly to

respond the reaction of the brake when releasing

the switch trigger. Sudden reaction can drop the tool

oyourhandandcancauseapersonalinjury.

To prevent the switch trigger from being accidentally

pulled,alock-obuttonisprovided.Tostartthetool,

pressthelock-obuttonandpulltheswitchtrigger.

Release the switch trigger to stop.

►Fig.7: 1. Switch trigger 2.Lock-obutton

Shaft lock

Press the shaft lock to prevent spindle rotation when

installing or removing a diamond wheel.

►Fig.8: 1. Shaft lock

NOTICE: Never actuate the shaft lock when the

spindle is moving. The tool may be damaged.

Lighting the lamp

CAUTION: Do not look in the light or see the

source of light directly.

To turn on the operation lamp, press and hold the lock-

obuttonandpulltheswitchtrigger.

The lamp goes out 10 seconds after releasing the

switch trigger.

►Fig.9: 1. Operation lamp

NOTE:Useadryclothtowipethedirtothelensof

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Overload alert

If the tool is operated with excessive load, the operation

lamp will blink. In this situation, reduce the load on the

tool, and the lamp stops blinking.

Electronic function

Electric brake

This tool is equipped with an electric blade brake. If the

tool consistently fails to quickly cease to function after

the switch trigger is released, have the tool serviced at

a Makita service center.

Automatic speed change function

This tool has "high speed mode" and "high torque

mode".

The tool automatically changes the operation mode

depending on the work load. When the work load is low,

the tool will run in the "high speed mode" for quicker

cutting operation. When the work load is high, the tool

will run in the "high torque mode" for powerful cutting

operation.

Soft start feature

This function allows the smooth start-up of the tool by

limiting the start-up torque.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Hex wrench storage

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

►Fig.10: 1. Hex wrench

16 ENGLISH

Removing and installing diamond

wheel

CAUTION: Use only the Makita hex wrench

supplied to remove and install a diamond wheel.

CAUTION: When installing a diamond wheel,

be sure to tighten the bolt securely.

CAUTION: Always install a diamond wheel so

that the arrows on the diamond wheel point in the

same direction as the arrows on the wheel cover

and gear housing. Otherwise the wheel rotates in

reverse,itmaycausepersonalinjury.

To remove the diamond wheel, press the shaft lock

fully so that the diamond wheel cannot revolve and use

the hex wrench to loosen the hex bolt clockwise. Then

removethehexbolt,outerangeanddiamondwheel.

►Fig.11: 1. Shaft lock 2. Hex wrench 3. Hex bolt

4. Loosen 5. Tighten

NOTICE:Iftheinnerangeisremoved,installiton

the spindle with its wheel mounting part facing the

diamond wheel.

To install a diamond wheel, follow the removal pro-

cedure in reverse. Make sure the diamond wheel is

installed so that the arrows on the wheel point in the

same direction as the arrows on the wheel cover and

gear housing.

BE SURE TO TIGHTEN THE HEX BOLT SECURELY.

►Fig.12: 1. Hex bolt 2.Outerange3. Diamond

wheel 4.Innerange5. Cup washer

6. Arrow

Water supply tank

CAUTION: When lling the tank with water, be

careful not to spill water over the tool.

CAUTION: Be sure that the water supply lever

on the wheel cover is set in the “OFF” (O) position

before installing the water supply tank.

Installing water supply tank

Insert the tank with the water supply cap pointing down-

wards into the water supply holder until it locks with a

click.

►Fig.13: 1. Water supply cap 2. Water supply holder

Removing water supply tank

Presstheejectbuttontoreleasethetank,andthenpull

thetanko.

►Fig.14: 1.Ejectbutton

NOTICE:Becarefulnottoholdthewater-lledtank

upright (with its lid-cap facing downwards) as water

drops may leak out of the vent pin hole.

►Fig.15: 1. Lid-cap 2. Vent pin hole

Water supply hose

CAUTION: Be sure that the water supply lever

on the wheel cover is set in the “OFF” (O) position

before turning the water on.

Connecting to the mains water

supply

NOTE: The type of water outlet may vary depending

on your region of residence. Use an appropriate

faucet adapter or tap connector to attach the hose to

the mains water supply as necessary.

1. Connect the water supply plug to the supply water

outlet.

►Fig.16: 1. Supply water outlet 2. Water supply plug

2. Unscrew the water supply cap attached to the

water supply tank.

►Fig.17: 1. Water supply cap 2. Water outlet

NOTICE: Be careful not to lose the rubber washer

placed at the bottom of the water supply cap when-

ever you reassemble the cap.

3. Attach the water supply cap onto the cap plug of

the hose.

►Fig.18: 1. Water supply cap 2. Cap plug

4. Insert the hose with the water supply cap pointing

downwards into the water supply holder until it locks

with a click.

►Fig.19: 1. Water supply cap 2. Water supply holder

Disconnecting from the mains water

supply

1. Set the water supply lever on the wheel cover in

the“OFF”(O)positionandturnthewatero.

2. Presstheejectbuttontoreleasethewatersupply

hose,andthenpullthehoseo.

►Fig.20: 1.Ejectbutton

3. Remove the water supply plug from the supply

water outlet.

Installing dust cover

Optional accessory

CAUTION: When installing an optional wheel

cover, be sure to tighten the screw securely.

Removing standard-equipped wheel

cover

Remove all the attachments on the pre-installed wheel

cover before replacing it with an optional cover.

Loosen the screw and pull the cover apart from the gear

housing.

►Fig.21: 1. Screw

17 ENGLISH

Installing optional wheel cover

Mount an optional wheel cover aligning its guide

grooves with the guide ridges on the gear housing.

Then tighten the screw securely.

►Fig.22: 1. Guide grooves on wheel cover 2. Guide

ridges on gear housing

Dust bag

Optional accessory

The use of the dust bag makes cutting operations clean

anddustcollectioneasy.Toattachthedustbag,tit

onto the dust spout.

►Fig.23: 1. Dust bag 2. Dust spout

The neck of the dust spout rotates freely. Position the

dust bag so that you can operate the tool comfortably.

►Fig.24

When the dust bag is about one-third full, remove the

dust bag from the tool and pull the fastener out. Empty

the dust bag of its contents, tapping it lightly so as to

remove particles adhering to the insides which might

hamper collection.

►Fig.25: 1. Fastener

Connecting the vacuum cleaner

Optional accessory

When you wish to perform clean cutting operation,

connect a Makita vacuum cleaner to your tool.

►Fig.26: 1. Hose of the vacuum cleaner 2. Dust

spout

OPERATION

CAUTION: THIS TOOL SHOULD ONLY BE

USED ON HORIZONTAL SURFACES.

CAUTION: Be sure to move the tool forward

in a straight line and gently. Forcing and exerting

excessive pressure or allowing the wheel to bend,

pinch or twist in the cut can cause overheating of the

motor and dangerous kickback of the tool.

CAUTION: Be sure to feed water to a wet-type

diamond wheel during wet cutting operations.

Wet cutting with water supply tank

CAUTION: Avoid lling the water supply tank

with unclean water, such as muddy water, or else

the water outlet will be blocked resulting in dam-

age to the tool.

NOTICE: Be sure to drain out water from the water

supply tank completely after each use.

1. Openthelid-capofthewatersupplytank,andll

thetankwithwater.Thensetthewater-lledtankinthe

water supply holder of the tool.

►Fig.27: 1. Lid-cap

2. Holdthetoolrmly.Setthebaseplateonthe

workpiece to be cut without the diamond wheel making

any contact.

Straight cutting

►Fig.28

45° bevel cutting

►Fig.29

3. Start feeding water to the diamond wheel by pull-

ing the water supply lever towards the “ON” (I) position.

Waterowcanbeadjustedbymovingthewatersupply

lever. Turn the lever to the “ON” (I) position to increase

ow,andtothe“OFF”(O)positiontoreduceow.

►Fig.30: 1. Water supply lever 2. “ON” (I) position

3. “OFF” (O) position

4. Turn the tool on and wait until the diamond wheel

attains full speed. Then move the tool forward over

theworkpiecesurface,keepingitatandadvancing

smoothly until the cutting is completed. Keep your

cutting line straight and your speed of advance uniform.

5. Havingnishedoperation,besuretosetthelever

inthe“OFF”(O)positiontocutowo.

Wet cutting with water supply hose

CAUTION: Always pay attention to the control

of water pressure. Too high water pressure may

cause water leak and splashing.

1. Set the water supply lever in the “ON” (I) position.

►Fig.31: 1. Water supply lever 2. “ON” (I) position

3. “OFF” (O) position

2. Start feeding water to the diamond wheel by

turningthemainswatersupplyon.Waterowcanbe

adjustedbymovingthewatersupplylever.Turnthe

levertothe“ON”(I)positiontoincreaseow,andtothe

“OFF”(O)positiontoreduceow.

►Fig.32

3. Holdthetoolrmly.Setthebaseplateonthe

workpiece to be cut without the diamond wheel making

any contact.

Straight cutting

►Fig.33

45° bevel cutting

►Fig.34

4. Turn the tool on and wait until the diamond wheel

attains full speed. Then move the tool forward over

theworkpiecesurface,keepingitatandadvancing

smoothly until the cutting is completed. Keep your

cutting line straight and your speed of advance uniform.

5. Havingnishedoperation,besuretosetthelever

inthe“OFF”(O)positiontocutowoandturnthe

watero.

18 ENGLISH

WIRELESS ACTIVATION

FUNCTION

Optional accessory

NOTICE: Install the optional dust cover and

accessories before using this function.

What you can do with the wireless

activation function

The wireless activation function enables clean and com-

fortable operation. By connecting a supported vacuum

cleaner to the tool, you can run the vacuum cleaner

automatically along with the switch operation of the tool.

►Fig.35

To use the wireless activation function, prepare following items:

• A wireless unit (optional accessory)

• A vacuum cleaner which supports the wireless

activation function

The overview of the wireless activation function setting is

as follows. Refer to each section for detail procedures.

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION: Place the tool on a at and stable

surface when installing the wireless unit.

NOTICE:

Clean the dust and dirt on the tool before

installing the wireless unit. Dust or dirt may cause

malfunction if it comes into the slot of the wireless unit.

NOTICE:

To prevent the malfunction caused by static,

touch a static discharging material, such as a metal part

of the tool, before picking up the wireless unit.

NOTICE:

When installing the wireless unit, always

be sure that the wireless unit is inserted in the cor-

rect direction and the lid is completely closed.

1. Openthelidonthetoolasshowninthegure.

►Fig.36: 1. Lid

Insert the wireless unit to the slot and then close the lid.

Wheninsertingthewirelessunit,aligntheprojections

with the recessed portions on the slot.

►Fig.37: 1. Wireless unit 2.Projection3. Lid

4. Recessed portion

When removing the wireless unit, open the lid slowly. The hooks on

the back of the lid will lift the wireless unit as you pull up the lid.

►Fig.38: 1. Wireless unit 2. Hook 3. Lid

After removing the wireless unit, keep it in the supplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the vacuum

cleaner

NOTE: A Makita vacuum cleaner supporting the

wireless activation function is required for the tool

registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger or turn on the power switch on the

vacuum cleaner.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

If you wish to activate the vacuum cleaner along with

theswitchoperationofthetool,nishthetoolregistra-

tion beforehand.

1. Install the batteries to the vacuum cleaner and the

tool.

2. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►Fig.39: 1. Stand-by switch

3. Press the wireless activation button on the vac-

uum cleaner for 3 seconds until the wireless activation

lamp blinks in green. And then press the wireless acti-

vation button on the tool in the same way.

►Fig.40: 1. Wireless activation button 2. Wireless

activation lamp

If the vacuum cleaner and the tool are linked success-

fully, the wireless activation lamps will light up in green

for 2 seconds and start blinking in blue.

NOTE:Thewirelessactivationlampsnishblinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

lessactivationbuttonbrieyandholditdownagain.

NOTE: When performing two or more tool registra-

tionsforonevacuumcleaner,nishthetoolregistra-

tion one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the vacuum

cleaner prior to the wireless activation.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

After registering a tool to the vacuum cleaner, the

vacuum cleaner will automatically runs along with the

switch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the

tool.

►Fig.41

3. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►Fig.42: 1. Stand-by switch

19 ENGLISH

4. Push the wireless activation button on the tool

briey.Thewirelessactivationlampwillblinkinblue.

►Fig.43: 1. Wireless activation button 2. Wireless

activation lamp

5. Pull the switch trigger of the tool. Check if the

vacuum cleaner runs while the switch trigger is being

pulled.

To stop the wireless activation of the vacuum cleaner,

push the wireless activation button on the tool.

NOTE: The wireless activation lamp on the tool will

stop blinking in blue when there is no operation for

2 hours. In this case, set the stand-by switch on the

vacuum cleaner to "AUTO" and push the wireless

activation button on the tool again.

NOTE: The vacuum cleaner starts/stops with a delay.

There is a time lag when the vacuum cleaner detects

a switch operation of the tool.

NOTE: The transmission distance of the wireless unit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

vacuum cleaner, the vacuum cleaner may start run-

ning even if you do not pull the switch trigger because

another user is using the wireless activation function.

Description of the wireless activation lamp status

►Fig.44: 1. Wireless activation lamp

The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the

meaning of the lamp status.

Status Wireless activation lamp Description

Color

Blinking

Duration

Standby Blue 2 hours The wireless activation of the vacuum cleaner is available. The

lampwillautomaticallyturnowhennooperationisperformed

for 2 hours.

When

the tool is

running.

The wireless activation of the vacuum cleaner is available and the

tool is running.

Tool

registration

Green 20 seconds Ready for the tool registration. Waiting for the registration by the

vacuum cleaner.

2 seconds Thetoolregistrationhasbeennished.Thewirelessactivation

lamp will start blinking in blue.

Cancelling

tool

registration

Red 20 seconds Ready for the cancellation of the tool registration. Waiting for the

cancellation by the vacuum cleaner.

2 seconds Thecancellationofthetoolregistrationhasbeennished.The

wireless activation lamp will start blinking in blue.

Others Red 3 seconds The power is supplied to the wireless unit and the wireless activa-

tion function is starting up.

O - - The wireless activation of the vacuum cleaner is stopped.

Cancelling tool registration for the

vacuum cleaner

Perform the following procedure when cancelling the

tool registration for the vacuum cleaner.

Install the batteries to the vacuum cleaner and the tool.

Set the stand-by switch on the vacuum cleaner to "AUTO".

►Fig.45: 1. Stand-by switch

3. Press the wireless activation button on the vac-

uum cleaner for 6 seconds. The wireless activation

lamp blinks in green and then become red. After that,

press the wireless activation button on the tool in the

same way.

►Fig.46: 1. Wireless activation button 2. Wireless

activation lamp

If the cancellation is performed successfully, the wire-

less activation lamps will light up in red for 2 seconds

and start blinking in blue.

NOTE:Thewirelessactivationlampsnishblinkingin

red after 20 seconds elapsed. Press the wireless acti-

vation button on the tool while the wireless activation

lamp on the cleaner is blinking. If the wireless acti-

vation lamp does not blink in red, push the wireless

activationbuttonbrieyandholditdownagain.

20 ENGLISH

Troubleshooting for wireless activation function

Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

The wireless activation lamp does

not light/blink.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or

the slot is dirty.

Gentlywipeodustanddirtontheterminalofthe

wireless unit and clean the slot.

The wireless activation button on the

tool has not been pushed.

Push the wireless activation button on the tool

briey.

The stand-by switch on the vacuum

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to

"AUTO".

No power supply

Supply the power to the tool and the vacuum cleaner.

Cannotnishtoolregistration/can-

celling tool registration successfully.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or

the slot is dirty.

Gentlywipeodustanddirtontheterminalofthe

wireless unit and clean the slot.

The stand-by switch on the vacuum

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to

"AUTO".

No power supply

Supply the power to the tool and the vacuum cleaner.

Incorrect operation

Pushthewirelessactivationbuttonbrieyandperform

the tool registration/cancellation procedures again.

The tool and vacuum cleaner are away

from each other (out of the transmission

range).

Get the tool and vacuum cleaner closer to each other.

The maximum transmission distance is approximately 10

m however it may vary according to the circumstances.

Beforenishingthetoolregistration/cancellation;

-theswitchtriggeronthetoolispulledor;

- the power button on the vacuum

cleaner is turned on.

Pushthewirelessactivationbuttonbrieyand

perform the tool registration/cancellation procedures

again.

The tool registration procedures for the

toolorvacuumcleanerhavenotnished.

Perform the tool registration procedures for both the

tool and the vacuum cleaner at the same timing.

Radio disturbance by other appliances

which generate high-intensity radio

waves.

Keep the tool and vacuum cleaner away from the

appliances such as Wi-Fi devices and microwave

ovens.

The vacuum cleaner does not run

along with the switch operation of

the tool.

The wireless unit is not installed into the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or

the slot is dirty.

Gentlywipeodustanddirtontheterminalofthe

wireless unit and clean the slot.

The wireless activation button on the

tool has not been pushed.

Pushthewirelessactivationbuttonbrieyandmake

sure that the wireless activation lamp is blinking in blue.

The stand-by switch on the vacuum

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to

"AUTO".

More than 10 tools are registered to the

vacuum cleaner.

Perform the tool registration again.

If more than 10 tools are registered to the vacuum

cleaner, the tool registered earliest will be cancelled

automatically.

The vacuum cleaner erased all tool

registrations.

Perform the tool registration again.

No power supply

Supply the power to the tool and the vacuum cleaner.

The tool and vacuum cleaner are away

from each other (out of the transmission

range).

Get the tool and vacuum cleaner closer each other. The

maximum transmission distance is approximately 10 m

however it may vary according to the circumstances.

Radio disturbance by other appliances

which generate high-intensity radio

waves.

Keep the tool and vacuum cleaner away from the

appliances such as Wi-Fi devices and microwave

ovens.

The vacuum cleaner runs while the

tool's switch trigger is not pulled.

Other users are using the wireless

activation of the vacuum cleaner with

their tools.

Turnothewirelessactivationbuttonoftheother

tools or cancel the tool registration of the other

tools.

Leht laadib ...

Makita DCC501 Kasutusjuhend

Bränd: Makita

Mudel: DCC501

Kategooria: Nurklihvijad

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

svenska: Makita DCC501 Användarmanual
dansk: Makita DCC501 Brugermanual

Makita DCC501 Kasutusjuhend

Makita DCC501 Kasutusjuhend

teistes keeltes

Seotud paberid