Leht laaditakse ...
Not for
Reproduction
Manual No. 80080372 Rev -
Copyright © 2019. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
BRIGGSandSTRATTON.com
GE6500I
(030797-00)
en - English
Not for
Reproduction
1
B
V
F
G
H
X
J
W
U
S
P
Q
N
K
Z
E
Y
> 6.1 m
N
Not for
Reproduction
3
2
9
10
3
4
7
5
B
6
8
Not for
Reproduction
Safety and Control Symbols ................... 4
Equipment Description........................ 4
Features and Controls ........................ 5
Operation................................... 5
Maintenance ................................ 8
Storage .................................... 9
Troubleshooting ............................10
Specifications ..............................10
Warranty ..................................11
The safety alert symbol indicates a potential personal
injury hazard. A safety symbol may be used to represent
the type of hazard. indicates a hazard which,
if not avoided, could result in death or serious injury.
indicates a hazard which, if not avoided, could
result in minor or moderate injury. NOTICE indicates
information considered important, but not hazard-related.
For questions regarding European emissions, please
contact our European office at:
The inverter generator is an engine–driven, revolving
field, alternating and direct current (AC & DC) generator.
The generator is designed to supply electrical power
for operating compatible electrical lighting, appliances,
tools and motor loads. The generator’s revolving field is
To move generator, press button and pull handle out.
Press button to push handle back in. Use handholds for
convenient lifting.
The portable generator can be used to power outdoor
items using an extension cord or to restore home power
using a transfer switch. A transfer switch is a separate
device installed by a licensed electrician that allows
the portable generator to be cord connected, using the
receptacle, directly into your home’s electrical system.
Install a manual transfer switch as soon as possible if
generator will be used to provide home power restoration.
Every effort has been made to ensure that information
in this manual is accurate and current. However, the
manufacturer reserves the right to change, alter, or
otherwise improve the generator and this document at any
time without prior notice.
NOTICE If you have questions about intended use,
contact an authorized service dealer. This equipment is
designed to be used with Briggs & Stratton® authorized
parts ONLY.
The generator has a system ground that connects the
generator frame components to the ground terminals
on the AC output receptacles. The generator neutral is
floating ( ), which means that the AC stator winding
is
isolated from the grounding fastener and the AC receptacle
ground pins. Electrical devices, such as RCD, requiring
a grounded neutral may not operate properly from this
generator. Earthing of the generator is not required.
There may be regulations, local codes, or ordinances
that apply to the intended use of the generator. Please
consult a qualified electrician, electrical inspector, or the
local agency having jurisdiction.
This generator is not intended to be used at a
construction site or similar activity.
This symbol indicates the owner of
batteries and electrical or electronic
equipment shall not dispose of this
product with unsorted municipal waste.
This product should be disposed of in
environmentally appropriate waste
locations. Please contact Briggs & Stratton or your local
retailer for additional disposal information.
Fire
Explosion
Toxic Fumes
Hot Surface
Electrical Shock
Safety Alert
Symbol
Instruction Manual
Oil Level
Carbon
Monoxide Alarm
Circuit Breaker
On
Ground Terminal
Floating
Neutral
Off
Fuel
Engine Control
!
Do Not Start
Engine
Choke
Run
Suffication
Suffication
Oil
Alternating
Current (AC)
Direct
Current (DC)
Not for
Reproduction
5
1
Before starting the portable generator there are two
equally important safety concerns regarding carbon
monoxide poisoning and fire that must be addressed.
Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas.
•
Operate portable generator only outdoors, at least 6.1 m
from occupied spaces with exhaust pointed away to
reduce the risk of carbon monoxide accumulating.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• Do not run portable generator inside homes, garages,
basements, crawlspaces, sheds, or other partially
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after this product has shut off.
• Always point the engine exhaust away from occupied
spaces.
If you start to feel sick, dizzy, weak, or your homes
carbon monoxide alarm sounds while using this product,
get to fresh air right away. Call emergency services. You
may have carbon monoxide poisoning.
Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
• Portable generator must be at least 1.5 m from any
structure, overhang, trees, shrubs, or vegetation over
30.5 cm in height.
• Do not place portable generator under a deck or
other type of structure that may confine airflow.
Smoke alarm(s) must be installed and maintained
indoors according to the manufacturer’s instructions/
recommendations.
• Carbon monoxide alarms cannot detect smoke.
• Do not place portable generator in manner other than
shown.
• Use outdoors far away from any home.
• Point exhaust away from all homes and
occupied spaces.
• Install CO alarms inside your home.
6.1 m min.
MUFFLER
1.5 m min.
Exhaust
1.5 m min.
6.1 m min.
Retractable Handle N Handholds
B QPT Switch P Air Cleaner
Overload Reset Q Engine Identification
Power Use LED’s Back Cover
E Low Oil Indicator S Side Maintenance
Cover
F Recoil Starter Identification Label
G Choke Control U Fuel Cap
H Engine Switch V USB Ports
J 230 Volt AC, 16 Amp
Receptacles
W Grounding Fastener
K Spark Arrester Muffler X Main Breaker
Oil Fill/Dipstick Y 230 Volt AC, 32 Amp
Receptacle
Oil Drain Plug Z Circuit Breakers (AC)
Not for
Reproduction
2
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF
or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
3
4
5
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure generator is on a level surface.
2. Loosen three side maintenance cover screws and
remove cover (3).
3. Clean area around oil fill and remove dipstick.
4. Verify oil is at the full mark () (top hole) on
dipstick.
5. If needed, using oil funnel, slowly pour oil into oil fill
opening (4) to full mark () (top hole) on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick
clean each time oil level is checked. DO NOT overfill.
6. Replace and tighten dipstick.
7. Replace maintenance cover and hand tighten screws.
NOTICE Do not attempt to crank or start engine before
before it has been properly serviced with recommended
oil. This could result in an engine failure.
6
7
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline with a minimum of
91 RON (87 octane/87 AKI).
• Gasoline with up to 10% ethanol content is acceptable.
NOTICE Do not mix oil in gasoline or modify engine to
run on alternate fuels. Do not use unapproved gasoline
such as E15 and E85. Use of unapproved fuels could
damage generator and voids warranty.
See High Altitude for 1,524 m and above.
Fuel and its vapors
are extremely flammable and
explosive which could cause
burns, fire or explosion resulting in death or serious
injury.
• Do not refuel or move during operation.
• Turn engine off and let it cool at least 2 minutes before
removing fuel cap.
• Fill fuel tank outdoors. Do not spill fuel.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• Do not light a cigarette or smoke.
• Do not pour water on generator to put out fire.
• Only use a extinguisher rated for flammable liquids
and electrical systems such as a powder extinguisher.
Follow the instructions provided by fire extinguisher
manufacturer before use.
• This generator is not for use in explosive atmospheres.
1. Slowly remove fuel cap () to relieve pressure in
tank.
2. Slowly add unleaded fuel to fuel tank. Be careful not
to fill above lip (7). This allows adequate space for
fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
At altitudes over 1524 m, a minimum 89 RON
(85 octane/85 AKI) fuel is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the engine
at altitudes below 762 m with the high altitude kit is not
recommended.
When transporting equipment with a vehicle or trailer,
turn engine switch to OFF (0) position. Do not tip engine
or equipment at angle which causes fuel to spill.
The low oil indicator system is designed to prevent
engine damage caused by not enough engine oil. If the
engine oil level drops below a preset level, the red LED
low oil indicator light comes on and an oil level switch will
stop the engine. If the engine stops or the red LED low oil
indicator light comes on when you pull the recoil handle,
check the engine oil level.
1
NOTICE Always have QPT switch OFF (0) when starting
or stopping generator or when using DC USB ports.
Disconnect all electrical loads from the generator. Use
the following start instructions:
1. Make sure unit is outdoors on a level surface.
NOTICE Failure to operate the unit on a level surface
may cause the unit to shut down.
2. Pull choke control () out to close choke (
).
NOTICE For a warm engine, be sure choke lever is in
RUN (
) position.
3. Turn engine switch () to ON (I) position.
4. Grasp recoil handle () and pull slowly until slight
resistance is felt. Then pull rapidly to start engine.
5. Open choke gradually as engine warms up by
pushing in on choke handle.
NOTICE If engine fails to start, push choke control in
and repeat step 4. If engine starts but fails to run, see
Low Oil Indicator.
1
This feature improves fuel economy. When QPT switch
() is turned ON, the engine speed will increase
as electrical loads are connected, and decreased as
electrical loads are removed.
With the switch off, the engine will run at a higher speed.
Not for
Reproduction
7
Connections to your home’s electrical system must use a
manual transfer switch installed by a qualified electrician.
The connection must isolate the generator power from
the utility power and comply with all applicable laws and
electrical codes.
Generator may only be loaded up to rated power under
the rated conditions as shown on unit data tag. Reduce
load when using generator outside of rated conditions.
Use only high quality, well-insulated extension cables in
accordance with IEC 60245-4 with the generator’s 230
Volt AC outlets. Inspect extension cables before each
use. Check that all extension cables are suitably rated
and are not damaged. When using extension cords
under 40° C, the total length of cords for a cross section
of 1.5 mm² should not exceed 60 m or for a cross section
of 2.5 mm² should not exceed 100 m.
Damaged or overloaded extension
cords could overheat, arc, and burn resulting in
death or serious injury.
• Electrical equipment, including cables and plug
connections, should not be defective.
1. Install carbon monoxide alarm(s).
2. When operating generator with extension cords,
make sure it is located in an open, outdoor area,
at least 6.1 m from occupied spaces with exhaust
pointed away.
3. Extension cords running directly into home,
powering indoor items IS NOT RECOMMENDED.
Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you
in minutes. You cannot smell it, see it, or taste
it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Extension cords running directly into the home
increase your risk of carbon monoxide poisoning
through openings.
• If an extension cord running directly into the home is
used to power indoor items, the operator recognizes
that this increases the risk of CO poisoning to people
inside the home and assumes that risk.
4. Install a manual transfer switch as soon as possible
if generator will be used to provide home power
restoration.
Use receptacles to operate 230 Volt AC, single–phase,
50 Hz electrical loads requiring up to 3,680 watts (3.68
kW) at 16 Amps of current.
Generator voltage could cause
electrical shock or burn resulting in death or
serious injury.
• Do not touch bare wires or receptacles.
• Do not use generator with electrical cords which are
worn, frayed, bare or otherwise damaged.
• Do not operate generator in the rain or wet weather.
• Do not handle generator or electrical cords while standing
in water, while barefoot, or while hands or feet are wet.
• Do not allow unqualified persons or children to operate or
service generator.
• Keep children a safe distance from generator.
Use receptacle to operate 230 Volt AC, single–phase, 50
Hz electrical loads requiring up to 5,000 watts (5.0 kW) at
21.7 Amps of current.
The maximum current available for the USB ports is 2.1
Amps at 5 Volts. The USB port allows you to recharge
most USB powered devices with a USB charging cable
(not included).
NOTICE For maximum output when charging Apple
devices, use the bottom USB port.
NOTICE For charging ITE (Information Technology
Equipment) only.
The power use monitor indicates the percentage of total
generator load using 4 LED’s.
1st Green
2nd Green
3rd Yellow
4th Flashing Red 100%
4th Steady Red Overloaded
If the generator is overloaded, it cuts power to the
receptacles. Turn off and unplug all electrical loads.
Press the OVERLOAD RESET button, plug in and restart
electrical loads one at a time to continue in normal
operating mode.
1. Turn off and unplug all electrical loads from generator
panel receptacles. Never stop engine with electrical
devices plugged in and turned on.
2. Let engine run at no-load for one minute to stabilize
internal temperatures of engine and generator.
3. Turn engine switch to OFF (0) position.
Not for
Reproduction
Follow hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions.
• Change engine oil
• Clean debris
• Check engine oil level
• Clean engine air filter
• Inspect muffler and spark arrester
1
• Change engine oil
1
• Replace engine air filter
• Replace spark plug
1
Service more often under dirty or dusty conditions.
2
See authorized service dealer.
Regular maintenance will improve performance and
extend the life of the outdoor generator. See any Briggs
& Stratton Authorized Service Dealer for service.
Installation and major repair work should only be
performed by specifically trained personnel.
The generator’s warranty does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the generator as instructed in this manual.
To ensure machine safety, use
only original spare parts from the manufacturer
or approved by the manufacturer. Should you
have questions about replacing components on your
generator, please visit our website at
.
Excessive high or low operating
speeds could result in minor injury. Do not tamper
with governor spring, links or other parts to change
speed. Do not modify generator in any way.
CO2 values of Briggs & Stratton Type Approved engines
can be found at BriggsandStratton.com by typing CO2
into the search bar.
3
4
5
8
Avoid prolonged or repeated skin
contact with used motor oil. Used motor oil has
been shown to cause skin cancer in certain
laboratory animals. Thoroughly wash exposed areas with
soap and water.
KEEP OUT OF REACH OF CHILDREN. DON’T
POLLUTE. CONSERVE RESOURCES.
RETURN USED OIL TO COLLECTION
CENTERS.
Change oil while engine is warm from running, as follows:
1. Make sure generator is on a level surface.
2. Remove oil drain plug () and drain oil completely
into a suitable container.
3. Reinstall oil drain plug () and tighten securely.
4. Loosen the three maintenance cover screws (3) and
remove the side maintenance cover.
5. Clean area around oil fill, remove dipsitck and wipe
with clean cloth.
6. Slowly pour recommended oil (about 1.0 l) into oil fill
opening (4). Pause to permit oil to settle. Fill to full
mark (top hole) on dipstick ().
7. Wipe dipstick clean each time oil level is checked.
Do not overfill.
8. Reinstall dipstick.
9. Wipe up any spilled oil.
10. Replace the side maintenance cover and hand
tighten the three maintenance cover screws.
Not for
Reproduction
9
3
9
10
Changing the spark plug will help your engine to start
easier and run better.
1. Loosen the three maintenance cover screws and
remove the side maintenance cover (3).
2. Clean area around spark plug and remove spark
plug boot (9).
3. Remove spark plug and inspect spark plug.
4. Replace spark plug if electrodes are pitted, burned
or porcelain is cracked. Use the recommended
replacement plug. See Specifications.
5. Check electrode gap with wire feeler gauge (10)
and reset spark plug gap to recommended gap if
necessary (see Specifications).
6. Install spark plug and tighten firmly. Reinstall spark
plug boot.
7. Replace the side maintenance cover and hand
tighten the three maintenance cover screws.
Inspect spark arrester for damage or carbon blockage. If
damage is found or cleaning is needed, see a Briggs &
Stratton Authorized Service Dealer.
Contact with muffler area could
cause burns resulting in serious injury.
• Pay attention to the warnings on the generator.
• Do not touch hot parts.
If storing the unit for more than 30 days, use the following
guidelines to prepare it for storage.
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine outdoors for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Then run the engine outdoors until it stops from lack of
fuel. The use of a fuel stabilizer in the storage container
is recommended to maintain freshness.
Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury.
• When storing fuel or equipment with fuel in tank, store
away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
• When draining fuel, turn generator engine off and let it
cool at least 2 minutes before removing fuel cap.
• Loosen cap slowly to relieve pressure in tank.
• Drain fuel tank outdoors.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
While engine is still warm, drain oil from crankcase. Refill
with recommended grade. See Changing Engine Oil.
1. DO NOT store fuel from one season to another
unless it has been treated as described in Protect
Fuel System.
2. Store generator in clean, dry area and cover with a
suitable protective cover that does not retain moisture.
Storage covers could cause a fire
resulting in death or serious injury.
• Do not place a storage cover over a hot generator.
• Let equipment cool for a sufficient time before placing
the cover on the equipment.
Not for
Reproduction
10
1. Red LED light is steady. Generator is
overloaded or overheated.
2. Poor connection or defective cord set.
3. Connected device is bad.
1. Remove loads from generator.
Press OVERLOAD RESET button
on control panel.
2. Check and repair.
3. Connect another device that is in
good condition.
1. Generator is overloaded.
1. Remove loads from generator.
1. Engine switch set to OFF (0) position.
2. Low oil indicator light comes on. Low
oil level.
3. Out of fuel.
4. Spark plug wire not connected to
spark plug.
5. Flooded with fuel.
1. Set switch to ON (I) position.
2. Fill crankcase to proper level or
place generator on level surface.
3. Fill fuel tank.
4. Connect wire to spark plug.
5. Wait 5 minutes and re-crank engine.
The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of
Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995.
Torque values are derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower
values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments. Actual gross engine
power will be higher than net engine power and is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline engine may not develop the rated gross power
when used in a given piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety
of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating
conditions (temperature, humidity, altitude), and engine-to engine variability. Due to manufacturing and capacity limitations, Briggs &
Stratton may substitute an engine of higher rated power for this engine.
* The momentary electrical current the generator can provide to start electric motors, per Briggs & Stratton 628K. It does not
represent the power required to continuously run electrical loads. It is the maximum current that can momentarily be supplied when
starting a motor, multiplied by the generator’s rated voltage.
** Generator per EN ISO 8528-13:2016, Reciprocating internal combustion engine driven generating sets- Part 13: Safety.
Starting Watts* ..................................................6,500
Running Watts** .................................................5,000
Load Current:
at 230 Volts AC ............................................21.7 Amps
at 5 Volts DC ...............................................2.1 Amps
Rated Frequency ..............................................50 Hertz
Phase....................................................Single Phase
Displacement ..................................................306 cc
Spark Plug Gap............................................... 0.76 mm
Fuel Capacity ...............................................18.9 Liters
Oil Capacity..................................................1.0 Liters
Spark Plug.................................................... 798615
Engine Oil Bottle ...................................... 100005 or 100028
Synthetic Oil Bottle ............................................. 100074
For a full list of parts and diagrams, please visit BRIGGSandSTRATTON.COM.
Not for
Reproduction
11
80011053_EN Rev. A
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for
and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
.
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
After 12 months, warranty covers parts only.
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components
are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial use,
it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover
damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
- The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
- Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Equipment 24 months 12 months
Engine* 24 months 12 months
Battery (if equipped) 3 months None
Not for
Reproduction
........... 4
.................. 4
........... 5
.............................. 5
..................... 8
................................ 9
. 10
............................10
.................................11
може
посочва
опасност, която, ако не бъде избегната, би могла да
доведе до малка или средна степен на нараняване.
ПРЕДУПРЕЖДЕНИЕ
®
ПРЕДУПРЕЖДЕНИЕ
BRIGGS & STRATTON®.
!
(DC)
Not for
Reproduction
5
1
•
MUFFLER
N
B
P
Q
E
S
F
G
U
H
V
J
W
K
X
Y 230 V AC, 32 A,
Z
Not for
Reproduction
2
3
4
5
2.
3).
4
ПРЕДУПРЕЖДЕНИЕ
ПРЕДУПРЕЖДЕНИЕ
6
7
ПРЕДУПРЕЖДЕНИЕ
Висока надморска височина
2.
(7).
Not for
Reproduction
7
1
ПРЕДУПРЕЖДЕНИЕ
ПРЕДУПРЕЖДЕНИЕ
2. ).
ПРЕДУПРЕЖДЕНИЕ
).
5.
ПРЕДУПРЕЖДЕНИЕ
Индикатора за ниско ниво на маслото.
1
2.
Not for
Reproduction
ПРЕДУПРЕЖДЕНИЕ
ПРЕДУПРЕЖДЕНИЕ
100%
1
1
1
2
.
3
4
5
8
()
()
(3)
Not for
Reproduction
9
4
().
3
9
10
(3)
(9).
Спецификации.
10
Спецификации).
Смяна на моторното масло.
Защита на горивната система.
Not for
Reproduction
10
1.
5.
...................................6 500
...................................5 000
.................................
....................................
..........................................
.....................................................
...................................................... 306 cc
.......................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.......................................
............................................ 798615
...........................
................................. 100074
Not for
Reproduction
11
80011053_BG Rev. A
.
**
*
**
Not for
Reproduction
............... 4
............................... 4
....................... 5
Provoz ..................................... 5
..................................... 8
.................................. 9
............................10
............................10
....................................11
ukazuje na riziko,
může
ukazuje na riziko,
které, jestliže se ho nevyvarujete, může vést k malému či
střednímu poranění. UPOZORNĚNÍ
Pro
tuto dokumentaci.
UPOZORNĚNÍ
POUZE
je
proudem
Hladina
oleje
obvodu
Zapnuto
svorka
Vypnuto
Palivo
motoru
!
Nestartujte
motor
Zapnuto
Olej
proud (AC)
proud (DC)
/