AGFEO ST 40 Kasutusjuhend

ST 40
AGFEO
Kaubamärk
AGFEO
Mudel
ST 40
Tüüp
Kasutusjuhend

See juhend sobib ka

User Guide
System Telephone ST 40 S0
System Telephone ST 40 UP0
System Telephone
Safety Notes
- Do not connect or disconnect the subscriber´s line of ST 40 during a storm.
- Lay the subscriber´s line in such away that nobody steps on or tripples over it.
- Take care that no liquids spill inside the digital system telephone.This can cause short-circuits.
Regarding this User Guide.
This user manual is valid for the at the time installed system firmware. As the ST 40 is controlled
via the telephone system it may be that after a firmware change some parts of this manual will no
longer be appropriate. This manual will give a brief explanation to the operation of the ST 40 and the
features of your AGFEO Telephone System. For detailed information regarding features, please refer
to user manual of your Telephone System.
The digital System Phone ST 40 S0 is for the connection to an internal S0-Bus of an AGFEO ISDN
Telephone System. The ST 40 may be connected to the following AGFEO ISDN Telephone Systems:
- AS 151 plus, AS 181 plus, AS 181 plus EIB from Software 8.1
- AS 281 All-In-One, AS 35, AS 35 All-In-One from Software 7.0
- AS 40 P (P400-1), AS 4000 (P400-1), AS 100 IT (P400 IT), AS 43, AS 45, AS 200 IT from Software 7.0
The digital System Phone ST 40 UP0 is for the connection to an UP0-Bus of an AGFEO ISDN
Telephone System. The ST 40 UP0 may be connected to the following AGFEO ISDN Telephone
Systems:
- AS 43, AS 45, AS 200 IT from Software 7.5
Please note due to the higher power consumption of the AGFEO ST 40 when connected to the
internal S0-Bus and the limited system capacity for systems already on the market like the AS 40P
(P400-1), AS 4000 (P400-1) and AS 100 IT (P400 IT), it may become necessary to use additional power
supply units. A ST 40 has a maximum power consumption of 1,7 Watt (all LEDS are lit, A Module 40
inserted, with ringer active, volume to maximum) the S0 Bus of an S0 440 module is based on a
double port (4,5 Watt), therefore the max. load is already over the permitted limit with the
connection of 2 x ST 40 and 1 x ST 30 (P max. 1,3 Watt)in the worst case scenario. In such cases the
system may activate the safety protection circuit for the relevant double port. (System Phones /
ISDN Bus without any function. After reset of the system the ports will be reinstated)! In such
eventualities an additional power supply should be connected in order to avoid such failure to occur.
The power supplies are available from your distributor, AGFEO Ref. No. 6100756 for Great Britain
and Cyprus only, AGFEO Ref. No 6100826 for all other countries (Identical to Power Supply Unit STE
40 / DECT S0 -Base plus).
Information regarding software upgrades are available via your dealer.
AGFEO will not accept any liability for damages which may result from improper use of the digital
System Phone ST 40.
Stipulation for use:
System Telephone
ST 40
3
Stipulation for use ................................................................................................................................. 2
Safety Notes .......................................................................................................................................... 2
Regarding this User Guide. ................................................................................................................... 2
Underneath the ST 40 ............................................................................................................................ 4
The connection of an Untangler ............................................................................................................ 4
Display Position ..................................................................................................................................... 5
ST 40 Registration ................................................................................................................................. 5
Connect the ST 40 ................................................................................................................................. 5
ST 40 Buttons ........................................................................................................................................ 6
Display of the ST 40................................................................................................................................ 7
Menu Guidance ..................................................................................................................................... 7
Notes on using this Manual .................................................................................................................. 7
Function Buttons - Freely programmable Function Buttons (overview) ............................................. 8
LED - Display for freely programmable function buttons .................................................................. 10
Button Assignment ............................................................................................................................. 12
"Direct Access" activated .................................................................................................................... 12
"Direct Access" deactivated ................................................................................................................ 12
Call Waiting .......................................................................................................................................... 13
Reject the waiting call ......................................................................................................................... 13
Requesting Ring back when free ........................................................................................................ 13
Call Pick Up (External) ......................................................................................................................... 13
Call Pick Up (from Answering machine) ............................................................................................. 13
Display Call Log ................................................................................................................................... 14
Programming the Do Not Disturb function ........................................................................................ 14
Changing the retrieval method ........................................................................................................... 14
Phonebook (Numeric retrieval) ........................................................................................................... 14
Phonebook (Alphabetic retrieval) ......................................................................................................... 15
Phonebook (Vanity retrieval) ................................................................................................................ 15
Extended Redial ................................................................................................................................... 15
Automatic Redial ................................................................................................................................. 15
Place of Installation ............................................................................................................................. 16
Cleaning ............................................................................................................................................... 16
Inserting inscription for the function keys ......................................................................................... 16
DHSG Headset (Cordless Headset) ...................................................................................................... 17
Connection of Headset ........................................................................................................................ 17
DSHG Headset Operation .................................................................................................................... 18
ST 40 Firmware Upgrade ..................................................................................................................... 18
Table of Contents
System Telephone
ST 40
4
S0-TK
Modulslot 1
Modulslot 2
Underneath the ST 40
The connection of an Untangler
In the handset of the ST 40 you will find a compartment for a cord untangler. Due to this design the
untangler will not be obtrusive when on the phone or interfere when on the receiver is put back on
hook.
- to open the handset cover , press the lid (arrow 1) and remove lid (arrow 2).
- unplug the handset cord from the handset.
- connect the untangler to the handset.
- connect the handset cable to the untangler.
- Close the lid
Connection for op-
tional Power Plug
or Optional STE 40
Connection to
the PBX System
Module Shaft
for optional
A-Module 40
Connection of
Receiver
Connection for
Headset
1)
2)
System Telephone
ST 40
5
Connect the ST 40
To operate the ST 40, please insert the RJ 45 plug into the relevant socket which is connected to the
internal ISDN line of your AGFEO ISDN Telephone System.
- insert the RJ 45 plug into the socket until your hear a positive click.
- to release the plug, press the release latch on the plug and at the same time pull the cable out of
the socket. (use a small screw driver if required)
To operate the ST 40 UP0, please insert the RJ 45 plug into the relevant socket which is connected
to the UP0 port of your AGFEO ISDN Telephone System.
Please note only one telephone can be connected to each UP0 port.
- insert the RJ 45 plug into the socket until your hear a positive click.
- to release the plug, press the release latch on the plug and at the same time pull the cable out of
the socket. (use a small screw driver if required)
Please note that the S0 Bus must be terminated with two 100 Ohm ¼ Watt Resistors, the UP0 port
does not require any termination.
An extension number will be allocated to the ST 40, like any other device when programming the
telephone system. If you connect the ST 40 for the first time to the telephone system, then the digi-
tal system phone will have to be registered to the system. Please follow the instruction in the
display.
ST 40 Registration
Display Position
Your Display can be adjusted to 6 different viewing angles.
System Telephone
ST 40
6
ST 40 Buttons
M
akeln
1
Firma
M
a
keln
2
IH
K
Hd
R
Konferenz
J.
Fliege
Umleitung
zu
Versicherung
Ban
k
G
e
bühren
Nacht
Anrufschu
tz
E. Pasc
h
ke
Durch
s
age
S
ven
ja
Yara
T
e
rm
i
n
e
T.Christia
n
Intern
Anwalt
1
A
B
C
2
3
D
E
F
4
G
H
I
5
JK
L
6
M
N
O
7
P
Q
R
S
8
T
U
V
9
W
X
Y
Z
0
+
-
Numeric Keypad
* and # Buttons
Set Button - Start and end
programming. Keep this button
pressed to toggel between
programming tree and
programming index
Handsfree Button - Activates the
Loudspeaker. Button lights up
when activated.
Arrow Buttons - To scroll through
the display where there is more
than one function.
Phone Book Button - Retrieval of
Telephone Numbers.
LNR - Last Number Redial But-
ton. Keep this button pressed to
show call log.
10 Function But-
tons and LED's
Adjustable
Graphic Display
Loudspeaker
underneath
handset
Microphone
Button Labelling
1 0
* #
!
=
y&
t
:
Softkeys
M
%
Mail Button - Flashes on new
entry in call log or missed calls.
Stays lit for numbers already
viewed. Clears when number is
called or deleted from list by
pressing clear button
10 function Buttons - User
programmable, two entries per
Button (First & Second Level)
Keep this button pressed for
approx 1 sec. to show the second
level. LED indication only for first
level.
Plus and minus for volume
control of handset and speaker.
Softkeys: The function for these
buttons are shown in the display
above. Function offered are
depending on the relevant phone
status.
+
-
System Telephone
ST 40
7
Menu Guidance
Please look at the display when using the telephone as it will guide you through all operating
procedures. Depending on its operating condition the following soft keys are offered:
Answer, Park Call, Retrieve, Get, Split, Transfer, Call Back. Conference, Recall, Reject,
Disconnect, Go To, Back, End, OK, on, off, Store and Door Opener.
x
i
A
*
External ISDN-Line. One line (a B-
channel)is busy. The "x" is shown
inverted on an external call.
Internal ISDN-Line. One Line (a B-
channel) is busy.
Analogue trunk line. The "A" is shown
inverted on an external call
Features:
Browse with
yx, Confirm with „ok“
Call-Waiting off
Do Not Disturb on
Diversion/ISDN-call forwarding
active
CVA 2 (Night service) on
Phone lock on
Wake-up on
Appointment on
Sensor activated
Filter ativated
Withhold own number
PC Programming in process
$
{
}
%
"
S
F
I
PC
Display in
standby:
Activated features
are shown here
Extensions off hook.
Called extension
will be shown
inverted.
Internal and
external S0 Status,
one box per S0.
Current function of
soft key below.
1. Display Line: Date / Time
Index of functions:
Display of the ST 40
WK26 Tu 11.Jul.06 11:59
ii xx A *${}%“S
12 14 16 18
ok back
Status of analogue
trunk lines
The soft keys below the phone display will be indicated by this symbol.
The relevant button which is to be pressed will be shown in black.
Please observe the display area if no black button is indicated. Should there be more than
three option, then the most used function will be shown first. More functions can be
selected by pressing the arrow buttons.
Notes on using this Manual
System Telephone
ST 40
8
Function Buttons - Freely programmable
Function Buttons (overview)
To switch TAM module on or off of the ST 30 System Phone.
To listen to messages recorded on the TAM.
To record messages on the TAM
Reject the ringing call. Caller will hear busy tone.
You can select if:
If the caller will get busy tone if on a call. (off)
If a waiting call should only be visually indicated on your phone.
Or if a call waiting tone should be signalled. (audible)
To divert an incoming call during the ringing phase. There will be no change to the
ringing tone when diverted. The caller will not be aware that the call was forwarded.
To switch Call Filters on or off.
Will list the Call Log
In connection with the check in / check out button. This can be used to signal to the
front desk that a room has been cleaned and is ready for occupation.
This will disable the Tone Ringer
Special function buttons may be set:
DND for internal calls
DND for external calls
DND for internal- and external calls.
Night Service on or off.
Special function buttons may be set:
Night Service can be switched for each trunk line.
Night Service can be switched for all trunk lines.
Enable / Disable Call Forward if designated extension does not answer on incoming call.
Special function buttons may be allocated:
Switch Call Forward for each trunk line.
Switch Call Forward for all trunk lines.
Announcement via Public Address Amplifier connected to the Telephone System
Return Busy Tone to Caller if one Extension is Busy within Call Distribution Group.
Special Buttons can be assigned
-Busy on Busy for each Call Distribution Group swithcable seperately
-Busy on Busy for call Call Distribution Group switchable together
To select Network Provider via LCR
Check in / Check out for Hotel applications. Will start and stop call logging and switch
on or off trunk line access.
Pageing Announcement to System Phones. Programmable function Button - Page
specific Extensions.
Display Call Cost
Malicious Call Identification via ISDN-Exchange
Sending of stored DTMF Tones (1..0 * #) for a remote interogation of a Telephone
Answering Machine (TAM)
Possible to make the ringing extension go off hook from another phone.
Log in and out of Groups and their features
To use a Headset (only Digital System Phones)
To mute microphone on your telehpone.
TAM activation
TAM info
TAM Memo
Reject
Call Waiting
Enabled / off
Call Deflection
Call Filter
Call Log
Cleaning
Do not Disturb
(DND)
Night Service
(AVA 2)
Call Forwarding
Tannoy
Busy on Busy
Call by Call
Check In/ Check
Out
Page (Tannoy)
Units
Call Capture
Remote functions
Remote Answer
Group Button
Headset
Mute Button
System Telephone
ST 40
9
Function Buttons - Freely programmable
Function Buttons (overview)
Call Pick Up
Withhold
Internal Button
ISDN-Hold
ISDN-Call
Forwarding
Conference
Speaker
Volume
LCR
Call Split
Brokers Call
External
Relays
Reserve
Sensor
SMS info
Write SMS
Message
Enquiry Call
Telephone
Book
Telephone Lock
Appointment
Timer
Doorphone and
Lock Release
Transfer
Diversion from
(Follow me)
Diversion to
Wake Up
Destination
Button
- Public
- Private
To Pick Up incoming calls. Special Function Button can be assigned to Pick Up
internal and external calls from specific extensions.
To withhold own number to be sent to a called party.
To Dial Extensions. Special function Button programmable: Call specific Extension
To Hold an external call in the Telephone Exchange (only available on PTMP
connection)
To switch on or off the ISDN Call Fowarding feature.
To set up a Coneference Call with Internal and or External calls.
To set the Speaker Volume Level for Handsfree or On Hook use.
To switch Least Cost Routing (LCR) on or off for your System Phone.
To talk to more then one External Call in turn. (Switch between them)
To talk to one internal and one external call at a time and without connecting
them.
To transmit another of your MSN numbers other the the one allocated to the Ex-
tension making the call. A special Button can be assigned for this feature.
To switch a Relays. A special function Button can be assigned.
To reserve a line should all lines be engaged at the time.
To Enable or Disable Sensors.
Will list all saved SMS messages
To write new SMS message.
To establish or set up an Enquiry Call, a connection or a Brokers Call
To select a number out of the System Telephone Book
To Lock the System Phone and activate pr-set Emergency and Direct Call numbers.
To set or cancel a preset Appointment Time
To switch on or off a Time based function, such as Day-Night Service, Call
Forwarding, Relays etc. Button can be assigned for this function. 10 Timers are
available. Timers are form 0 to 9.
Function Button can be assigned to connect to the Doorphone. Another Button can
be assigned to activate Lock Release.
To transfer and connect an external call to an external call.
To divert all calls from another phone to the current phone used.
To divert all calls to another extension- or external number.
To Enable or Disable the set Wake up call..
To Call a preset Telephone Number
- This number is stored in the Telephone System Memory
- This number is only stored in your telephone
System Telephone
ST 40
10
LED - Display for freely programmable
function buttons
Answering Machine
Messages
Call Waiting activation
Call Log
Do Not Disturb
Night Service
Call Forwarding
Busy on Busy
Group Button
Headset
Withhold Number
LCR
Relays
SMS Info
Mute Button
Telephone Lock
Appointment
Ringer Off
Doorphone and
Lock Release
Diversion from
Diversion to
Wake Up
Stored messages
already listened to.
enabled
Call Log entries
already viewed
on
on
set
on
Logged in
active
on
on
on
Messages already
read
enabled
on
set
on
connected to door
phone
enabled
enabled
set
LED on
No Messages
disabled
No numbers in
Call Log
off
off
off
off
Logged out
off
off
off
off
No Messages
disabled
off
off
off
switched off
disabled
disabled
off
LED off LED flashes
New Messages
New Numbers in Call
Log
Telephone is being
called
Relay is being rung
New Messages
when appointment call
is ringing
called from door phone
Wake up call not
answered
System Telephone
ST 40
11
General information on the Line-key
The line-keys are supported by an ST 30 because an allocated LED is indispensable. Another
condition for meaningful use is that, two keys are always installed for one line.In the „resting“
status,you can get further information about the line by pressing a flashing line-key (e.g.the caller´s
phone number). Press the flashing linen-key in the ‘pick up´ status, take the call.
TAM Activation
Internal Button
Line Button
Timer Button
Destination But-
ton
LED on LED off LED flashes
(fast)
LED flashes
(slowly)
The TAM is
activated
The TAM is
deactivated
The Timer is on,
the function is off
Both, the Timer
and the function
are on.
Both, the Timer
and the function
are off.
The internal key is
allocated to an
answering
machine
1)
. It has
taken the call. The
call can be
taken by pressing
the key.
You are holding
the internal
subscriber (query
or Call Split).
Only you can
take the call
again.
The extension
subscriber is
busy. He is
beeing called or
he is calling.
The Line is busy, it
can not be used
The Line is in a
status for all to take
the call.
The Line is beeing
held and can be
taken over only by
this subscriber.
The line is free
and the subscriber
can use it with an
external button.
Flashes when the
number calls. The
call can be picked
up by pressing a
key.
Goes off as soon
as somebody
answers the call.
LED - Display for freely programmable
function buttons
1) Only valid for answering machine at analogous Port
System Telephone
ST 40
12
Button Assignment
On delivery of the Phone System all programmable function But-
tons of the Phones have a default setting which are the same on all
System Telephones.
These Buttons can be individual programmed to suit your specific
needs.
Announce Call Waiting
Mute
Tone Call
Internal
Call Filter
System Memory
System Memory
System Memory
System Memory
System Memory
System Memory
System Memory
System Memory
System Memory
System Memory
Appointment
Diversion to
System Memory
System Memory
Changing Button Assignment
!31
z
%
z
y& !
Start
Programming
Press Button,
you want to
assign
Confirm
selection
Enter the first letter of the
function ´s name,or choose
the function with arrow buttons
End
Programming
Enter PIN if
prompted
()
"Direct Access" activated
+ #
z
Calling an internal user:
Lift receiver
Press the ‘Internal or Intercom’ Button
and dial the required extension number.
+
z
Calling an external number:
Lift receiver
Just dial the telephone number required. The telephone system
automatically seizes an outside line .
+
z
Calling an internal user:
Lift receiver
Dial the Extension
Number only
+
0z
Calling an external number:
Lift receiver
Dial 0 (or 9 if applicable) to get a line. On hearing external dial
tone dial required telephone number
"Direct Access" deactivated
System Telephone
ST 40
13
Requesting Ring back when free
Call Pick Up (External)
Call Waiting
TP- AP+ P A
You are on a call and
hear the call waiting
tone
Replace the
receiver to end the
current call.
Your telephone will
ring for you to
answer the waiting
call.
Lift Receiver Conduct Call
1. Possibility:
2. Possibility:
Press „SPLIT“. The first call is placed on hold while the waiting one is connected to you. You can alter between the calls by
pressing the Split Button. You can also deflect the waiting call.
Reject the waiting call
Press the „Reject“. The caller will now hear busy tone if you are
the only phone programmed to ring on an incoming call. If there
are also other phones programmed to ring on an incoming call
then the caller continues to hear the ringing tone.
Continue your original call.
P A
A-
On hearing the busy tone
when calling an extension.
Press Softkey "RecalL". Ring
back when free is initated
Replace Receiver
You wish to pick up an
external call.
a +
Lift receiver. Press Softkey „Get“.
You are now connected to the caller.
Call Pick Up (from Answering machine)
Answering machine has
accepted external callt.
A+%
Lift receiver. Press butoon Call Pick Up.
Only possible if button Call Pick Up is configured
to extension number of TAM.
System Telephone
ST 40
14
Programming the Do Not Disturb
function
You can toggle „Do not Disturb“ on/off by pressing the „Do not Disturb“ button.
Display Call Log
The flashing mail button will indicate that there is one entry in the call log. With the receiver
on hook press the mail button. The last missed call will be displayed giving telephone
number, date and time. The LED will continue to be lit until you return the call or delete the
entry from the call log.
You can use the arrow keys to view further entries.
y&
The displayed number will be dialled as soon as you lift the receiver. The entry will be
automatically being deleted if the caller answers. The entry will remain in the call log if no
one answers.
Delete the displayed entry by presseing the left button.
Abort the call log by pressing the right button.
Exit Programming
! % z !
Press Set and button
"Do not disturb" to
start programming
"1": Do not Disturb for Internal Calls
"2": Do not Disturb for External Calls
"3": Do not Disturb for Exernal and Internal Calls
Changing the retrieval method
t '&
Press
Phonebook
button
Press "Search" , choose search mode with arrow
buttons and confirm with middle button
Phonebook (Numeric retrieval)
Lift the receiver or press the handsfree
button. The displayed number will be
dialled.
t
Z
'& + =
or
Enter the stored
location of the entry, ie 000 to 999 or use
arrow buttons to scroll.
Press
Phonebook
button
System Telephone
ST 40
15
Phonebook (Vanity retrieval)
Scroll with arrow buttons '&
t z z + =
or
Enter the desired letter,ie.A =2.The
first entry with the selected initial
letter is displayed.
Select the next letter,ie.N
=6.The first entry
with “An ”is displayed.
Lift the receiver or press the
handsfree button,
the displayed name will
automatically be dialled.
Press
Phonebook
button
Scroll with arrow buttons '&
t z & z + =
or
Enter the desired
letter,ie.A =2.The first
entry with the selected
initial letter is
displayed.
Enter the second
letter,i. e. N =66.
Lift the receiver or press the
handsfree button. The
displayed phone number will
be dialled automatically.
Press
Phonebook
button
Press the arrow
button to move
to the input for
the second
letter.
Phonebook (Alphabetic retrieval)
Extended Redial
With the receiver on hook.
Press the “redial ”
button.The last phone number
dialled is displayed.
Automatic Redial
With the receiver on hook.
Press the “redial ”
button.The last phone
number dialled is
displayed.
-:y& +or =
-: +or =
Lift the receiver.The displayed
phone number is dialled.
Select one of the 10 last phone
numbers displayed by using the
arrow buttons.
With the receiver on hook press the redial button.The
last number dialled is displayed. Automatic redial will
start once you press the emidlle button. The LCD will
display how many more times the system is trying to
the requird number. The speaker will be switched on
automatically once the connection has been
established.
Pick up the receiver or press
the speaker button as
otherwise the line will be
cleared down after 10
seconds.
System Telephone
ST 40
16
Place of Installation
Install ST 40 in an appropriate place. Please pay attention to the following during the installation:
- Not in places,where the phone can be sprayed with water or chemicals.
- Synthetic support at the base of the phone:
Your apparatus was manufactured for normal conditions of use.Chemicals used in the production
or care of furniture can cause changes to the synthetic support of the phone. Such
apparatussupports changed by extraneous influence can leave behind unpleasant marks. Due to
understandable reasons,liability for such damages can not be taken. Use therefore a non-slippery
base for your phone,especially on new or freshly vanished furniture.
Cleaning
You can easily clean your phone. Pay attention to the following:
- Wipe the phone with slightly moist or antistatic cloth.
- Never use dry cloth (charging could lead to defective electronics).
- Take care by all means that moisture does not ooze into the phone (switch and contacts could be
damaged).
Inserting inscription for the function
keys
Your ST 40 includes a printed designation strip which shows the
button allocation in default. You may use the reverse to enter your
own designation.
Use a finger-nail between the upper end of the window and the
phone casing. Pull the window downwards until it buckles. You can
now take it out.
Insert the inscription strips. You can print corresponding lebels on your PC, using the TK-Set
configuration programm.
Re-insert the window at the lower end in the recess for inlay. By pressing downwards,the
window buckles and you can replace it.
System Telephone
ST 40
17
The ST 40 has a seperate RJ 10 headset connection. Instead of connecting the cordless DHSG
Headset AGFEO 9120 you may also use some of the following corded headsets:
Manufacturer Model Order No.
AGFEO Headset 2100 6548839
Headset 2200 6548847
Plantronics Supra Monaural Polaris Modell P51 * 32190-04
Tristar Modell P81 * 33695-01
* including connection cable U10P 38058-01
GN Netcom Profile monaural ** 1861-15-03
Optima NC monaural ** 1913-29-01
** Including connection cable 8800-00-01
DHSG Headset (Cordless Headset)
The DHSG connectivity is a new industry standard which is supported by various headset - and other
apparatus manufacturers. This bi-directional connection makes it possible to deliver a high
functionality between telephone and headset from different manufacturers. The telephone can
signal to the headset via the DHSG connection if it is on - or off hook and if the telephone is ringing.
Likewise the headset is able to signal to the phone if it wants to be on - or off hook. The condition
will be that both devices, telephone and headset, are able to support this type of protocol.
Connection of Headset
The headset socket can be found underneath the ST 40 (See Page 4). The socket is marked with a
headset symbol.
- insert the headset plug into the headset socket until you hear a positive click.
- lay the cable in the cable duct underneath the ST 40 which is also used as a strain relief
- to unplug the cable, release the latch on the plug (use a small screw driver if required) and at the
same time pull the plug out of the socket.
Please note you may need an adapter from RJ45 to RJ 11.
System Telephone
ST 40
18
Please program a headset button for the ST 40 or STE 40 either via TK-Suite or the system
programming code !31.
- You now will be able to answer or clear a call for the headset.
Your headset will also ring in the earpiece once your telephone rings.
- You can answer the call by pressing the programmed headset button on the ST 40 or STE 40, or by
pressing the button directly on your headset.
- If so required you may disable the ringer of the ST 40 but still will hear a call ringing directly in the
earpiece of your headset. This will be ideal for call centres or open plan offices.
- If the caller hangs up, then the telephone system will also clear the call and the headset goes
automatically on hook. There is no need to press a button on the ST 40 or the headset to go back
on hook.
DSHG Headset Operation
ST 40 Firmware Upgrade
Your System Phone ST 40 can be upgraded to the latest firmware level without the need to change
any hardware. To do so please do the following:
-*0# 1
z
With the handset
on hook the Sy-
stem Phone ST
40 is idle.
Press the buttons
*,0,# all at the same
time. The ST 40 is now in
service mode.
Select SoftwareUpdate by
pressing the digit 1.
If for any reason you do
not want to continue with
the update but want the
phone to return to normal
operation, then press digit
2 "Hauptprogramm"
(Main Program).
Enter the telephone
number of the Update
Server
004952144709950
[Updateserver AGFEO
Bielefeld]
If required enter access
digit 9 if no spontaneous
line seizure is set.:
9004952144709950
Confirm entry with
middle soft button
(ok). The Update
Server will now be
dialled and the
update will start.
The update will be completed within approx. 90 seconds. The ST 40 will automatically re register to
the telephone system. On start up the software level will be displayed on the phone. The update is
now completed.
System Telephone
ST 40
19
Ident no. 1101371
Subject to change without notice. No liability
can be accepted for errors contained in this
document.
Printed in Germany
0113
AGFEO GmbH & Co. KG
Gaswerkstr. 8
D-33647 Bielefeld
Internet: http://www.agfeo.com
The crossed out wheeled bin on the product means that this belongs to the group of
Electro- and electronic apparatus.
In this context you are directed by the European regulation to dispose of used apparatus
- at the point of buying an item of equal proportion / value
- at the local available collection point for disposal
With this you will participate in the reuse of material and valorisation of disused electric-
and electronic apparatus, which otherwise could be a health hazard and be negative to the
environment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

AGFEO ST 40 Kasutusjuhend

ST 40
AGFEO
Kaubamärk
AGFEO
Mudel
ST 40
Tüüp
Kasutusjuhend
See juhend sobib ka
Laadige alla PDF
aruanne

teistes keeltes

Seotud paberid

Muud dokumendid