Philips GC8210/03 Kasutusjuhend

GC8300 - GC8200 Series

2

3

A B C D FE G

H

I

J

K

L

M

PQRSTU

V

X

W

O

N

1

4

GC8300 - GC8200 Series

ENGLISH 6

 18

 31

 43

 54

 66

 78

 90

 102

 114

 126

 138

 151

 163

 175

 187

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/welcome.

The powerful pressurised ironing system produces non-stop steam to

make ironing easier. Thanks to the large water tank, you can iron without

interruption. When the water tank is empty, you can detach it and rell it

immediately.

We hope you enjoy using this ironing system.

General description (Fig. 1)

 Supply hose

B Handle (GC8261/GC8260 only: with soft grip)

C Temperature dial

D Steam trigger

E Temperature light

F Steam lock

G Shot-of-steam button (GC8325/GC8320/GC8261/GC8260/GC8225/

GC8220 only)

H Soleplate

I Safe storage lock (GC8261/GC8260 only)

J Iron stand

 Detachable water tank

L Cord & hose storage hook

M Calc-Clean rinsing cap

N Filling opening

O Water tank release lever

P Steam generator

Q On/off button with power-on light (GC8325/GC8320/GC8261/

GC8260/GC8225/GC8220 only)

R Transport handgrip

S Water tank rell light (GC8325/GC8320/GC8261/GC8260/GC8225/

GC8220 only)

 Calc-Clean light (GC8325/GC8320/GC8261/GC8260 only)

 Mains cord

V Steam buttons (+/-) (GC8325/GC8320/GC8261/GC8260/GC8225/

GC8220 only)

W Steam generator control panel with steam light (GC8325/GC8320/

GC8261/GC8260/GC8225/GC8220 only)

- p = maximum steam

- [ = moderate steam

- ] = minimum steam

- a = no steam

X On/off switch with power-on light (GC8210 only)

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Danger

- Never immerse the iron or the steam generator in water.

ENGLISH

Warning

- Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord, the supply hose or

the appliance itself shows visible damage, or if the appliance has been

dropped or leaks.

- If the mains cord or the supply hose is damaged, you must have it

replaced by Philips, a service centre authorised by Philips or similarly

qualied persons in order to avoid a hazard.

- Never leave the appliance unattended when it is connected to the

mains.

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- Do not let the mains cord and supply hose come into contact with the

hot soleplate of the iron.

- If steam escapes from under the Calc-Clean rinsing cap when the

appliance heats up, switch off the appliance and tighten the Calc-Clean

rinsing cap. If steam continues to escape when the appliance heats up,

switch off the appliance and contact a service centre authorised by

Philips.

- Never remove the Calc-Clean rinsing cap when the steam generator

is hot.

- Do not use any other cap on the steam generator than the Calc-Clean

rinsing cap that has been supplied with the appliance, as this cap also

functions as a safety valve.

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord and the supply hose regularly for possible

damage.

- Always place and use the iron and the steam generator on a stable,

level and horizontal surface.

- The soleplate of the iron can become extremely hot and may cause

burns if touched.

- When you have nished ironing, when you clean the appliance, when

you ll or empty the water tank and also when you leave the appliance

even for a short while: put the iron on the iron stand, switch off the

appliance and remove the mains plug from the wall socket.

- Rinse the steam generator regularly according to the instructions in

chapter ‘Cleaning and maintenance’.

- This appliance is intended for household use only.



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.

ENGLISH 7



Note: The iron may give off some smoke when you use it for the rst time. This

is normal and stops after a short while.

Note: Some particles may come out of the soleplate when you use the iron for

the rst time. This is normal; the particles are harmless and stop coming out of

the iron after a short while.

Note: When you switch on the appliance, the steam generator may produce a

pumping sound. This is normal; the sound tells you that water is pumped into

the steam generator.

1 Remove any sticker or protective foil from the soleplate and clean

the soleplate with a soft cloth.

Preparing for use

1 Place the steam generator on a stable and level surface, e.g. on the

hard part of the ironing board or on a table.

Filling the detachable water tank

You can ll the water tank at any time during use.

Do not put hot water, perfume, vinegar, starch, descaling agents, ironing

aids or other chemicals in the water tank.

Do not overll the water tank, otherwise water may spill out of the

lling opening when you reinsert the water tank.

1 Remove the detachable water tank from the steam generator.

2 Fill the water tank with tap water up to the MAX indication.

Note: If the tap water in your area is very hard, we advise you to mix it with an

equal amount of distilled water.

3 Slide the water tank rmly back into the steam generator (‘click’).

Note: If the water tank is not properly placed, the iron does not produce any

steam.





When the water tank is empty, the water tank rell light starts ashing and

steam ironing is no longer possible.

1 Remove the water tank and ll it.

2 Put the water tank back into the steam generator.

, The iron is ready for steam ironing again.

ENGLISH8

Setting the temperature

1 Check the laundry care label of the article to be ironed to determine

the required ironing temperature.

- 1 for synthetic fabrics ( e.g. acrylic, viscose, polyamide) and silk

- 2 for wool

- 3 for cotton

- MAX for linen

2 To set the required ironing temperature, turn the temperature dial

to the appropriate position.

3 Put the mains plug in an earthed wall socket.

4 Switch on the appliance.

- GC8325/GC8320/GC8261/GC8260/GC8225/GC8220 only: Press the

on/off button once.

, The power-on light of the on/off button goes on.

, The temperature light on the iron goes on. When the iron has

reached the set temperature, the temperature light goes out.

Note: During ironing, the temperature light goes on from time to time. This

indicates that the iron is heating up to the set temperature.

, The steam light starts ashing. After approx. 2 minutes, the steam

light stays on continuously to indicate that the steam generator is

ready for steam ironing.

- GC8210 only: Set the on/off switch to ‘on’.

, The power-on light in the on/off switch goes on.

, The temperature light on the iron goes on. When the iron has

reached the set temperature, the temperature light goes out.

Note: During ironing, the temperature light goes on from time to time. This

indicates that the iron is heating up to the set temperature.

, After approx. 2 minutes, the steam generator is ready for steam

ironing.



- If you do not know what kind or kinds of fabric an article is made of,

determine the right ironing temperature by ironing a part that is not

visible when you wear or use the article.

- If the fabric consists of various kinds of bres, always select the

temperature required by the most delicate bre, i.e. the lowest

temperature. For example: if a fabric consists of 60% polyester and 40%

cotton, it must be ironed at the temperature indicated for polyester (

1) and without steam.

- Start ironing the articles that require the lowest ironing temperature,

i.e. those made of synthetic materials.

- If you set a lower temperature during ironing, wait until the iron has

cooled down to the set temperature before you continue ironing. To

make the iron cool down faster, simply press the steam trigger or iron

a piece of cloth.

On

ENGLISH 9



Steam ironing

The supply hose may become hot during a long ironing session.

Note: The system may occasionally produce a pumping sound during steam

ironing. This is normal and tells you that water is pumped into the steam

generator.

1 Make sure there is enough water in the water tank.

2 Make sure the appliance is plugged in and switched on (see chapter

‘Preparing for use’).

3 Set the required ironing temperature (see chapter ‘Preparing for

use’).

Steam ironing is only possible at ironing temperatures higher than 2.

4 GC8325/GC8320/GC8261/GC8260/GC8225/GC8220 only: Set

the required steam setting with the + and - buttons on the steam

generator control panel.

p for maximum steam (temperature setting MAX).

[ for moderate steam (temperature settings 3 to MAX).

] for minimum steam (temperature settings 2 to MAX).

a for no steam (temperature settings 1 to MAX).

, The steam light ashes to indicate that the steam generator is

heating up.

, After approx. 2 minutes, the steam light stays on continuously to

indicate that the steam generator is ready for steam ironing.

Note: During ironing, you can adjust the steam setting with the + and - steam

buttons. It takes a few moments before the amount of steam is adjusted.

5 Press the steam trigger to start steam ironing.

When you put down the iron during ironing, put it on its heel or on the

iron stand.

, The opening and closing of the steam valve in the steam generator

causes a clicking sound. This is normal.

Steam lock function

The steam lock allows you to steam iron non-stop without having to press

the steam activator continuously.

- When you slide the steam lock forwards, the iron produces steam

continuously. To stop steaming, slide the steam lock backwards.

- When the steam lock is deactivated, the iron only produces steam

when you press the steam trigger.

Note: Release the steam lock when you put the iron on its heel or on the iron

stand. This prevents that hot steam escapes from the iron or that the iron

stand gets wet.

Vertical steaming

Never direct the steam at people.

ENGLISH10

1 Hold the iron in vertical position and press the steam trigger to

steam iron hanging curtains and clothes (jackets, suits, coats).





A powerful shot of steam helps to remove stubborn creases.

1 Set the temperature dial to a position between 3 and MAX.

2 Press the shot-of-steam button.

Note: Use the shot-of-steam function intermittently. If water droplets come out

of the soleplate, let the iron heat up for at least one minute before you use the

shot-of-steam function again.

Ironing without steam

There are one or two ways to iron without steam:

- All types: Simply start ironing without pressing the steam trigger.

- GC8325/GC8320/GC8261/GC8260/GC8225/GC8220 only: Select

steam setting a (no steam) and start ironing.



- When you steam iron woollen fabrics, shiny patches may occur. To

prevent this, use a dry pressing cloth or turn the article inside out and

iron the reverse side.

- Silk, woollen and synthetic materials: iron the reverse side of the fabric

to prevent shiny patches.

- Iron velvet and other fabrics that tend to acquire shiny patches in one

direction only (along with the nap) while you apply very little pressure.

- Do not use steam when you iron coloured silk. This could cause stains.

ENGLISH 11

Cleaning and maintenance



1 Put the iron on the iron stand (see chapter ‘Storage’) and switch

off the appliance.

2 Remove the mains plug from the wall socket and let the appliance

cool down.

3 Wipe scale and any other deposits off the soleplate with a damp

cloth and a non-abrasive (liquid) cleaner.

4 Clean the upper part of the iron and the outside of the steam

generator with a moist cloth.

5 Empty the water tank after cleaning.

Calc-Clean function

Never remove the Calc-Clean rinsing cap when the steam generator is

hot.

VERY IMPORTANT: Rinse the steam generator once a month or after

every 10 times of use, to prevent damage to the appliance and for

optimal steaming performance.

1 Unplug the appliance and let it cool down for 2 hours.

2 Remove the detachable water tank.

3 Hold the steam generator with both hands and shake well.

4 Turn the steam generator on its side with the Calc-Clean rinsing cap

facing upwards, and remove the Calc-Clean rinsing cap.

Off

ENGLISH12

5 Empty the steam generator into the sink.

6 Fill the steam generator with fresh water and shake again.

7 Empty the steam generator into the sink again.

8 Repeat steps 6 & 7 twice to obtain the best result.

9 Screw the Calc-Clean rinsing cap tightly back onto the steam

generator.



1 The Calc-Clean light ashes for 30 seconds when it is time to rinse

the steam generator.

The steam generator does not heat up during these 30 seconds.

2 Switch off the appliance immediately and let it cool down.

Do not use the Calc-Clean function when the steam generator is hot.

3 Use the Calc-Clean function as described above.

Storage

Always let the appliance cool down before you store it.

ENGLISH 13

1 GC8261/GC8260 only: Insert the tip of the iron into the safe storage

lock on the stand.

2 GC8261/GC8260 only: Press down the back of the iron rmly

(‘click’).

3 Empty the water tank.

4 Pull out the cord & hose storage hook.

5 Secure the supply hose and mains cord.

6 To move the appliance, carry it by the handgrips on either side of the

steam generator.

ENGLISH14

Environment

- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.

Guarantee & service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

guarantee leaet). If there is no Consumer Care Centre in your country, go

to your local Philips dealer.



This chapter summarises the most common problems you could

encounter with the appliance. If you are unable to solve the problem with

the information below, contact the Consumer Care Centre in your country.

Problem Cause Solution

The appliance does

not become hot.

There is a connection problem. Check the mains cord, the plug and

the wall socket.

You have not switched on the appliance. GC8325/GC8320/GC8261/

GC8260/GC8225/GC8220: Press

the on/off button. GC8210: set the

on/off switch to ‘on’.

The set temperature is too low. Set a higher temperature.

Smoke comes out of

my new iron when I

switch it on.

Some parts of the appliance have been

lightly greased in the factory and may

initially give off some smoke when heated.

This phenomenon is normal and

ceases after a short while.

The iron does not

produce any steam.

There is not enough water in the water

tank.

Fill the water tank. See chapter

‘Preparing for use’, section ‘Filling the

detachable water tank’.

The steam generator has not heated up

sufciently.

Wait approx. 2 minutes. GC8325/

GC8320/GC8261/GC8260/

GC8225/GC8220 only: wait until the

steam light stays on continuously.

The set ironing temperature is too low

for steam ironing.

Set a temperature of 2 or higher.

GC8325/GC8320/GC8261/GC8260/

GC8225/GC8220 only: You have set

steam setting a (no steam).

Set steam setting ] (minimum

steam), [ (moderate steam) or p

(maximum steam).

ENGLISH 15

Problem Cause Solution

You have not placed the water

tank properly in the steam generator.

Place the water tank properly in the

steam generator (‘click’).

When the iron is set to a very high

temperature, the steam produced is

dry and hardly visible. It is even less

visible when the ambient temperature is

relatively high and it is entirely invisible

when the temperature is set to MAX.

Set the iron to a lower temperature,

e.g. 2, to check if the iron actually

produces steam.

Water droplets

come out of the

soleplate.

The set temperature is too low for steam

ironing.

Set a temperature of 2 or higher.

When you start steam ironing and when

you stop steam ironing for a while, the

steam still present in the supply hose

cools down and condenses into water.

This causes water droplets to come out

of the soleplate.

This is normal. When you start

ironing or when you continue

ironing after an interruption, hold

the iron over an old cloth and press

the steam trigger. Wait until steam

instead of water comes out of the

soleplate.

Flakes and impurities

come out of the

soleplate or the

soleplate is dirty.

Impurities or chemicals present in the

water have deposited in the steam vents

and/or on the soleplate.

Clean the soleplate with a damp

cloth.

The appliance

produces a pumping

sound.

Water is pumped into the steam

generator.

This is normal.

The pumping sound does not stop. Unplug the iron immediately and

contact an authorised Philips service

centre.

The iron produces

steam continuously.

The steam lock has been set to ‘on’. Set the steam lock to ‘off’ if you only

want to obtain steam when you

press the steam trigger (see section

‘Steam lock function’).

Dirty water comes

out of the soleplate.

Too much scale and minerals have

accumulated inside the steam generator.

Rinse the steam generator. See

chapter ‘Cleaning and maintenance’.

Steam escapes from

under the Calc-

Clean rinsing cap

when the appliance

heats up.

You have not tightened the Calc-clean

rinsing cap properly.

Switch off the appliance, tighten the

Calc-Clean rinsing cap and switch

on the appliance again. If steam

continues to escape when the

appliance is heating up, switch off the

appliance and contact a service

centre authorised by Philips.

ENGLISH16

Problem Cause Solution

The iron does not

produce enough

steam/the amount

of steam decreases

and increases during

steam ironing.

When the appliance pumps water into

the steam generator, the steam amount

sometimes decreases. This is probably

when you think that the iron does not

produce enough steam. However, this is

a normal phenomenon and the steam

output normalises within a few seconds.

To optimise the steam output,

release the steam lock when you do

not need steam and when you put

down the iron.

Wet spots appear

on the fabric during

ironing.

The wet spots that appear on the fabric

after you have steam ironed for some

time may be caused by steam that has

condensed onto the ironing board. Iron

the wet spots without steam for some

time to dry them. If the underside of the

ironing board is wet, wipe it with a piece

of dry cloth.

To prevent steam from condensing

onto the ironing board, use an

ironing board with a wire mesh top.

GC8325/GC8320/

GC8261/GC8260/

GC8225/GC8220

only: Water droplets

come out of the

soleplate when I use

the shot-of-steam

function.

Steam may have condensed in the hose,

the temperature may have been set

below 3 or the appliance may not be

ready for steam ironing.

Make sure the temperature is set to

3 or higher. Steam iron for a few

seconds before you use the shot-of-

steam function.

ENGLISH 17

18



Поздравления за вашата покупка и добре дошли във Philips! За

да се възползвате изцяло от предлаганата от Philips поддръжка,

регистрирайте продукта си на www.philips.com/welcome.

Тази мощна система за гладене под налягане дава непрекъсната

пара и така прави гладенето по-лесно. Благодарение на големия

воден резервоар можете да гладите без прекъсване. Когато водният

резервоар се изпразни, можете да го откачите и веднага да го

напълните.

Надяваме се, че работата с тази система за гладене ще ви донесе

удоволствие.



 Захранващ маркуч

B Дръжка (само за GC8261/GC8260: с меко покритие)

C Температурен регулатор

D Спусък за пара

E Светлинен температурен индикатор

F Заключване на спусъка на парата

G Бутон за парен удар (само за GC8325/GC8320/GC8261/GC8260/

GC8225/GC8220)

H Гладеща повърхност

I Ключалка за безопасно съхранение (само за GC8261/GC8260)

J Поставка за ютията

 Подвижен воден резервоар

L Скоба за прибиране на кабела и маркуча

M Капаче за промиване на системата за почистване на накип (Calc-

Clean)

N Отвор за пълнене

O Лост за освобождаване на резервоара за вода

P Генератор за пара

Q Бутон вкл./изкл. с индикация (само за GC8325/GC8320/GC8261/

GC8260/GC8225/GC8220)

R Дръжка за транспортиране

S Светлинен индикатор за празен воден резервоар (само за

GC8325/GC8320/GC8261/GC8260/GC8225/GC8220)

 Индикатор на системата за почистване на накип (само за GC8325/

GC8320/GC8261/GC8260)

 Захранващ кабел

V Бутони за пара (+/-) (само за GC8325/GC8320/GC8261/GC8260/

GC8225/GC8220)

W Контролен панел на парния генератор с индикатор за пара (само

за GC8325/GC8320/GC8261/GC8260/GC8225/GC8220)

- p = максимална пара

- [ = умерена пара

- ] = минимална пара

- a = без пара

X Ключ за вкл./изкл. със светлинен индикатор (само за GC8210)





Преди да използвате уреда, прочетете внимателно това ръководство

за експлоатация и го запазете за справка в бъдеще.



- Никога не потапяйте ютията или генератора за пара във вода.



- Преди да включите уреда в контакта, проверете дали

напрежението, отбелязано на табелката на уреда, отговаря на

напрежението на местната електрическа мрежа.

- Не използвайте уреда, ако щепселът, захранващият кабел или

маркучът имат видими повреди, както и ако уредът е падал или

тече.

- Ако захранващият кабел или маркучът е повреден, с оглед

предотвратяване на опасност той трябва да бъде сменен от

Philips, упълномощен от Philips сервиз или квалифициран техник.

- Никога не оставяйте уреда без наблюдение, когато е включен в

контакт.

- Този уред не е предназначен за ползване от хора (включително

деца) с намалени физически усещания или умствени недостатъци

или без опит и познания, ако са оставени без наблюдение и не са

инструктирани от страна на отговарящо за тяхната безопасност

лице относно начина на използване на уреда.

- Наглеждайте децата, за да не си играят с уреда.

- Не допускайте захранващият кабел и маркуч да се допират до

горещата гладеща повърхност на ютията.

- Ако по време на загряване на уреда изпод капачето за промиване

на системата Calc-Clean излиза пара, изключете уреда и затегнете

капачето за промиване на системата за почистване на накип.

Ако продължава да излиза пара по време на нагряване на уреда,

изключете го и се обърнете към упълномощен от Philips сервиз.

- Не отваряйте капачето за промиване на системата за почистване

на накип, докато парният генератор е горещ.

- Не използвайте никакви други капачки за парния генератор освен

тази, предназначена за промиване на системата за почистване на

накип и получена в комплект с уреда, тъй като капачката служи и

за предпазен клапан.



- Включвайте уреда само в заземен мрежов контакт.

- Проверявайте редовно за евентуални повреди по захранващия

кабел и маркуча.

- Винаги поставяйте и използвайте ютията и генератора за пара

върху хоризонтална, равна и стабилна повърхност.

- Гладещата повърхност на ютията може да се нагорещи много и да

причини изгаряне при докосване.

- Когато сте свършили с гладенето, когато почиствате уреда,

когато пълните или изпразвате водния резервоар, а също така

когато оставяте уреда дори за момент: поставете ютията върху

поставката, изключете уреда и издърпайте щепсела от контакта.

- Изплаквайте редовно парния генератор съгласно упътванията в

раздела “Почистване и поддръжка”.

- Този уред е предназначен само за битови цели.

 19



Този уред Philips е в съответствие с всички стандарти по отношение

на електромагнитните излъчвания (EMF). Ако се употребява правилно

и съобразно напътствията в Ръководството, уредът е безопасен за

използване според наличните досега научни факти.



Забележка: При първото използване ютията може да отдели малко

дим. Това е нормално и след малко престава.

Забележка: Когато използвате ютията за пръв път, от гладещата

повърхност е възможно да паднат частици. Това е нормално;

частиците са безвредни и след малко престават да падат.

Забележка: Когато включите уреда, парният генератор издава

бълбукащ звук. Това е нормално; този звук показва, че към парния

генератор се изпомпва вода.

1 Махнете всякакви лепенки или защитно фолио от гладещата

повърхност и я почистете с мека кърпа.



1 Поставете генератора за пара върху стабилна и равна

повърхност, например върху твърдата част на дъска за гладене

или на маса.



Можете да пълните водния резервоар по всяко време при гладене.

Не сипвайте във водния резервоар гореща вода, парфюм, оцет, кола,

препарати за отстраняване на накип, помощни препарати за гладене

или други химикали.

Не препълвайте водния резервоар, тъй като може да се разлее вода

през отвора за пълнене при монтирането на резервоара.

1 Свалете подвижния воден резервоар от парния генератор.

2 Напълнете резервоара за вода с чешмяна вода до обозначението

МАХ.

Забележка: Ако чешмяната вода във вашия район е много твърда,

съветваме ви да смесвате чешмяната вода с равен обем дестилирана

вода.

3 Вмъкнете добре водния резервоар отново в парния генератор (с

щракване).

Забележка: Ако водният резервоар не е поставен добре, ютията няма

20

Leht laadib ...

Philips GC8210/03 Kasutusjuhend

See käsiraamat sobib ka

Philips GC8210/03 Kasutusjuhend

teistes keeltes

Seotud paberid