MuxLab HDMI / USB 2.0 Extender Kit, HDBT, 4K60 paigaldusjuhend

Bränd
MuxLab
Mudel
HDMI / USB 2.0 Extender Kit, HDBT, 4K60
Kategooria
Konsoolipikendused
Tüüp
paigaldusjuhend
© MuxLab Inc. 94-000807-A SE-000807-A
2321 Cohen Saint-Laurent, QC, Canada H4R 2N7
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: info@muxlab.com URL: www.muxlab.com
Specifications
Environment
KVM, HDMI 1.4 & USB 2.0
Devices
KVM, Monitors, TV, PC, laptops, mouse, keyboard.
Transmission
Transparent to the user.
Bandwidth
340 MHz
Signals
HDMI 1.4 protocol and USB 2.0
USB
One input on TX side and 4 outputs on RX side.
Bandwidth available: Up to 250 Mb/s.
Connectors
One (1) HDMI receptacle per TX & RX unit.
One (1) RJ45 for Cat 5e/6 UTP or STP per TX & RX unit.
On TX: 1 standard USB connector, type B.
On RX: 4 standard USB connectors, type A.
Two (2) 3.5mm jacks for IR sensor & emitter per TX & RX unit.
Note: Cables not included.
Maximum Distance
Based on a maximum
length of 6.6ft (2m) of
HDMI cable per end.
Cat 5e/6: 330 ft (100 m) up to 1920 X 1200 up to 60 Hz
330ft (100m) for 4K (3840 X 2160) up to 30Hz
Note: A minimum CAT5e/6 cable length of 12ft (4m) is required.
When installed in an electrically noisy environment, an STP cable
must be used.
RJ45 Pin
Configuration
Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight-
through wiring.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable
One (1) Cat 5e/6 or better twisted pair cable required.
Power Supply
Two (2) 110-240V/5VDC power supplies with interchangeable blades
Power Consumption
Transmitter: 3 Watts Receiver: 7 Watts + USB power
Temperature
Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Enclosure
Aluminum casting with plastic side panel.
Dimensions
4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)
Weight
2.6 lb. (1.2 kg)
Compliance
Regulatory: FCC, CE, RoHS Flammability: 94V0
Warranty
2 years
Accessories
500998 IR Emitter and 500994 IR Sensor
Ordering Information
500457 HDMI/USB 2.0 Extender Kit
HDMI/USB 2.0 Extender Kit
500457
Quick Installation Guide
Overview
The HDMI/USB 2.0 Extender Kit allows one HDMI 1.4 and one USB 2.0 channel to be
transmitted up to 330ft (100m) at all resolutions up to 3840 X 2160 @ 30Hz (including
1920x1200) via one (1) Cat 5e/6 cable in a point-to-point configuration. The receive
side includes a 4-port USB 2.0 hub, supporting KVM applications.
Applications
Applications include KMV commercial and residential AV systems, classroom projector
systems, digital signage, boardroom systems, collaborative PC systems, and medical
information systems.
Installation
1. Identify the connectors on the Transmitter and Receiver as indicated on the product
labels, see the above front and rear product views for further details.
2. Verify that the distance between the HDMI/USB 2.0 Transmitter and Receiver is
within MuxLab specifications.
3. To install the Transmitter:
3a. Connect the Transmitter to the HDMI video source with a HDMI compliant cable.
3b. Connect the Transmitter to the USB signal with a standard USB 2.0 cable.
3c. Connect a Cat 5e/6 (or higher) grade UTP cable of desired length within
specifications to the RJ45 LINK connector on the Transmitter.
© MuxLab Inc. 2015
4. To install the Receiver:
4a. Connect the Receiver to the HDMI display equipment with a HDMI compliant
cable.
4b. Connect the Receiver to as many as four (4) USB 2.0 peripherals with standard
USB 2.0 cables. Power is limited to 0.7A for the four (4) ports. An externally
powered four (4) port USB 2.0 hub may allow for expansion, or to support higher
power levels than 0.7A total.
4c. Connect the Cat 5e/6 cable coming from the Transmitter to the RJ45 LINK
connector on the Receiver.
5. Connect the 5 VDC power supply to the Receiver first, and then plug the power
supply into an AC power outlet. Next connect the 5 VDC power supply to the
Transmitter, and then plug the power supply into an AC power outlet. If power is
present, the power LED on the Transmitter and Receiver will be ON.
6. Power the HDMI equipment and verify the image quality.
7. This product supports unidirectional IR control. If infrared remote control is
needed to control the Source equipment from the Display, connect the IR Sensor
and/or IR Emitter to the 3.5mm Jacks of the Transmitter and Receiver.
8. Position the IR Sensor so that it is directed to the hand-held remote control. For a
clear IR signal reception, aim the hand-held remote control at the top of the IR
Sensor enclosure.
9. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD
player). For a clear IR signal reception, the IR Emitter can be glued on the source’s
IR Sensor. The IR Emitter’s signal is transmitted from the side of the enclosure.
10. The following diagram shows the final configuration.
(Note: IR sensor and emitter not shown in above diagram.)
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
with respect to issues during the installation of the HDMI/USB 2.0 Extender Kit:
Note: The Act LED should blink when the unit is working. The HDMI LED will blink if the
source contains no HDCP.
Symptom
Tx unit LEDs Rx unit LEDs
Probable
Cause
Possible
Solutions
Power
HDMI
RJ45
Power
HDMI
RJ45
No Image OFF - - OFF - - No power Check power
connections
No Image ON - OFF
ON - OFF
UTP Cable Check the UTP
cables.
No Image ON OFF ON ON OFF ON HDMI Cable Check the HDMI
cable.
No Image ON ON
(or
blink)
ON ON ON ON Cable length Check cable length,
check with another
monitor.
Flickering
Image or bad
sound
ON ON
(or
blink)
ON ON ON ON Cable length Check cable length
Check the HDMI
cable.
No sound, but
image OK
ON ON
(or
blink)
ON ON ON ON Sound at source Check if source or
monitor is PCM or
Dolby/DTS.
Image flickers
when powering
up nearby
equipment
ON ON
(or
blink)
ON ON ON ON Interference Use STP cables
USB not
working, but
audio/video
OK
USB 2.0 cable,
or too much
power required
for USB
peripheral.
Check USB 2.0 cable,
or
try another USB
device.
Adding
multiple USB
peripherals is
causing a
problem.
Too much
power required
for USB
peripherals.
Try a different USB
peripheral.
Try using an
externally powered
USB 2.0 hub.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
  • Page 1 1
  • Page 2 2

MuxLab HDMI / USB 2.0 Extender Kit, HDBT, 4K60 paigaldusjuhend

Bränd
MuxLab
Mudel
HDMI / USB 2.0 Extender Kit, HDBT, 4K60
Kategooria
Konsoolipikendused
Tüüp
paigaldusjuhend
Laadige alla PDF
aruanne

teistes keeltes

Seotud paberid