Hotpoint LDF 12314E Omaniku manuaal

Kategooria
Nõudepesumasinad
Tüüp
Omaniku manuaal

See käsiraamat sobib ka

Operating instructions
Contents
Installation, 2-3
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Description of the appliance, 4
Overall view
Control panel
Loading the racks, 5
Lower rack
Cutlery basket
Upper rack
Start-up and use, 6-7
Starting the dishwasher
Measuring out the detergent
Wash options
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions, advice and Assistance,11
General safety
Disposal
Saving energy and respecting the environment
Assistance
Troubleshooting, 12
English,1
EN
LDF 12314E
DISHWASHER
Français, 13
FR
Español, 49
PT
DE
Deutsch, 25
Português, 61
Polski, 73
PL
ES
NL
Nederland, 37
EN
2
Installation
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or moved,
please ensure the manual is kept with the machine, so that the
new owner may benefit from the advice contained within it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use and
maintenance of the appliance.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto
its back.
This appliance is intended to be used in household and
similar applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.
Positioning and levelling
1. Remove the appliance from all packaging and check that it
has not been damaged during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Check the dishwasher by placing it so that its sides or back
panel are in contact with the adjacent cabinets or even with the
wall. This appliance can also be recessed under a single
worktop
* (see the Assembly instruction sheet).
3. Position the dishwasher on a level and sturdy floor. If the
floor is uneven, the front feet of the appliance may be adjusted
until it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
4.
* Adjust the height of the rear foot from the front of the
appliance* on the central lower part of the dishwasher, turning
a hexagonal spanner (red color) with an opening of 8 mm in a
clockwise direction to increase the height or in an
anticlockwise direction to decrease the height.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies should
only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Do not use old hoses.
The water inlet and outlet hoses and the electricity supply
cable may be positioned towards the right or the left in order
to achieve the best possible installation.
Connecting the water inlet hose
To a suitable cold water connection point: before attaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
To a suitable hot water connection point: your dishwasher
may be supplied with hot water from the mains supply (if
you have a central heating system with radiators) provided
that it does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician (see Assistance).
The water pressure must be within the values indicated in
the Technical data table (see adjacent information).
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain
duct with a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to
80 cm from the floor / surface where the dishwasher
rests (A).
Before connecting the water outlet hose to the sink
drain, remove the plastic plug (B).
* Only available in selected models.
EN
3
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Some models are also equipped with the supplementary
safety device New Acqua Stop*, which guarantees anti-
flooding protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
The socket is earthed and complies with current
regulations.
The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located on
the inside of the door (see chapter entitled Description of
the appliance).
The power supply voltage falls within the values indicated
on the data plate on the inside of the door.
The socket is compatible with the plug of the appliance. If
this is not the case, ask an authorised technician to replace
the plug (see Assistance); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt (see
chapter entitled Rinse aid and refined salt). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value (see chapter entitled Rinse aid and
refined salt).
- After the salt has been poured into the
machine, the LOW SALT indicator light
* switches off.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
* Only available in selected models.
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC Waste Electrical
and Electronic Equipment
(WEEE)
EN
4
Overall view
Description of the
appliance
1. Upper rack
2. Upper sprayer arm
3. Tip-up compartments
4. Rack height adjuster
5. Lower rack
6. Lower sprayer arm
7. Cutlery basket
8. Washing filter
9. Salt dispenser
10. Detergent and rinse aid dispensers
11. Data plate
12. Control Panel
***
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Control panel
Low rinse aid
indicator light
ON/OFF/Reset
button
Half load button
Delayed start button
Extra Dry button
Wash cycle name
indicator light
ON/OFF
indicator light
Low salt
indicator light
Select wash
cycle button
Multi-functional tablets
indicator light
Short Time option
indicator light
Good Night option
indicator light
Extra Dry indicator light
Half load upper and
lower rack indicator
lights
Time remaining
light-up display
Start/Pause
button and
indicator light
Multi-functional
tablets button
Option button
Short Time
Good Night
option button
Delayed start
indicator light
EN
5
Loading the racks
Before loading the racks, remove all food residues from
the crockery and empty liquids from glasses and cups.
After loading the appliance, check that the sprayer arms
can rotate freely.
Lower rack
The lower rack can hold pans, lids, plates, salad bowls,
cutlery, etc. as seen in the Loading examples.
Plates and large covers should be placed at the sides of the
rack, ensuring that they do not block the rotation of the upper
sprayer arm.
Some dishwasher
models are fitted
with tip-up
sections
*, which
can be used in a
vertical position
when arranging plates or in a horizontal position when
arranging pans and salad bowls.
Cutlery basket
The type of cutlery basket may vary according to the
dishwasher model: it may be modular, non-modular or a sliding
version. The non-modular basket must only be positioned at
the front of the lower rack.
The modular basket
may be separated into
two parts, a solution
which is recommended
when performing a half
load wash (only in models offering this option), is available in a
sliding version (positioned at any point on the lower rack by
sliding it between the fixed or tip-up inserts.
- Both versions are fitted with a collapsible sliding system which
means the cutlery can be arranged in the best possible way.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on
the upper rack.
Cutlery basket positioning examples
Upper rack
Load this rack with delicate and lightweight crockery:
glasses, tea and coffee cups, saucers, small salad bowls,
saucepans and small saucepans which are not too soiled,
using the Loading examples as a guide.
Mugs and cups, long sharp knives and serving utensils:
place these on the tip-up compartments
**.
Tip-up compartments with adjustable tilt*
- The tilt feature can be used to increase the space in the upper
rack, to position wine glasses with different stem lengths safely
and to improve drying performance.
- Lift the tip-up compartment, slide it gently and position it in the
desired tilt angle.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper
rack may be moved to a higher or lower level.
(in models which offer the Baby cycle, the upper rack must be
placed in its lower position when the appliance is being loaded).
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
Never lift or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher or
lower as required, slide it along the guide
rails until the front wheels are in place and
close the stops (see figure).
If the rack is fitted with Dual Space
handles
* (see figure), pull out the upper
rack until it reaches its stop point, grip the
handles at the sides of the rack and move it
upwards or downwards, then slowly let it
fall back into place.
Loading examples for the upper/lower rack
Baby Tip-up compartments
*
For dishwasher models with a Baby Cycle,
tip-up compartments suitable for washing
bottles, rings and teats are provided. (see
the instruction sheet)
Items which should not be washed in the
dishwasher
Wooden items, objects with wooden or horn handles or glued-
on parts.
Items made from aluminium, copper, brass, pewter or tin.
Items made from plastic material which is not heat-resistant.
Antique or hand-painted porcelain.
Antique silver. Silver which is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
We recommend the use of crockery which is dishwasher safe.
* Only available in selected models.
** The number and position may vary.
Tilt A Tilt B Tilt C
EN
6
Start-up and use
* Only available in selected models.
Switching the appliance on for the first time
Selecting the language
Press the ON/OFF symbol; you will hear a short beep and the
display will show the set language.
Use the DELAYED START button to scroll forwards, or the HALF
LOAD button to scroll backwards through the list until you reach
the desired language. Press the P button to confirm the selection;
you will then automatically enter the list of wash cycles.
Every time the dishwasher is switched on subsequently, the list
of wash cycles will be displayed.
The language may also be changed at a later date, by pressing
the P button and the DELAYED START button simultaneously for
a few seconds.
Starting the dishwasher
1. Turn the water tap on.
2. Press the ON/OFF button: you will hear a short beep and
the display will light up.
3. Open the door and pour in a suitable amount of detergent
(see below).
4. Load the racks (see Loading the racks) and shut the door.
5. Select the wash cycle in accordance with the type of
crockery and its soil level (see Table of wash cycles) by
pressing the P button.
6. Select the wash options (see adjacent information).
7. Start the cycle by pressing the Start button: a long beep
signals the start of the wash cycle; the name of the selected
cycle is displayed, along with the time remaining until the end
of the cycle.
8. Two short beeps and one long one indicate the end of the
wash cycle and the text CYCLE END appears on the
display. Switch off the appliance by pressing the ON/OFF
button, shut off the water valve and unplug the appliance from
the electricity socket.
9. Wait for a few minutes before removing the crockery, in
order to avoid burns. Unload the racks, beginning with the
lower level.
AUTO WASH CYCLES
*: this model of dishwasher is
equipped with a special sensor which can be used to assess
the level of soiling and automatically select the most efficient
and economic wash cycle accordingly.
The duration of the auto wash cycles may vary due to the
operation of the sensor.
If the crockery is only lightly soiled or if it has been
rinsed with water before being placed in the dishwasher,
reduce the amount of detergent used accordingly.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it has
only just begun: once the wash cycle has started, switch off
the machine by pressing and holding the ON/OFF/Reset
button. Switch it back on using the same button and select the
desired wash cycle and options.
Adding extra crockery
Press the Start/Pause button (the corresponding indicator light
will flash). Open the door, taking care to avoid the escaping
steam, and place the crockery inside the appliance. Press the
Start/Pause button (fixed light): the cycle will restart after a
prolonged beep is emitted.
If the Start/Pause button is pressed so as to pause the
machine, the wash cycle or the Delayed Start function (if
selected) is interrupted.
At this stage it is not possible to change the wash cycle.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or once
the electricity supply is restored.
Measuring out the detergent
A good wash result also depends on the correct amount
of detergent being used; exceeding the stated amount
does not result in a more effective wash and increases
environmental pollution.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle has
ended.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing button D.
2. Pour in the detergent after consulting
the Table of wash cycles:
For powder detergent use
compartments A and B.
For detergent in tablet form: when the
cycle requires 1 tablet, place it in
compartment A and close the cover;
when it requires 2, place the second
tablet at the bottom of the appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
A
B
D
C
Wash options*
The OPTIONS may only be set, modified or reset after the
wash cycle has been selected and before the Start/
Pause button has been pressed.
Only the options which are compatible with the type of wash
cycle set may be selected. If an option is not compatible with the
selected wash cycle (see Table of wash cycles), the correspond-
ing LED flashes rapidly 3 times and 2 short beeps will sound.
If an option is selected which is incompatible with another (previ-
ously selected) option, the indicator light corresponding to the
option selected first will flash 3 times, 3 beeps will sound and it will
be deselected, while the most recently selected option will remain
active.
To deselect an option which has been set by mistake, press the
corresponding button again.
EN
7
* Only available in selected models.
Half load using the upper or lower rack
If there are not many dishes to be washed, a half load cycle
may be used in order to save water, electricity and detergent.
Select the wash cycle and press the HALF LOAD button
repeatedly: the triangle corresponding to the selected load will
illuminate and the wash cycle will take place only using the
upper or lower rack. If the button is pressed again, the option
will be deselected.
The Half Load option is not compatible with the Good
Night and Short Time options.
Remember to load the upper or lower rack only, and to
reduce the amount of detergent accordingly.
It is better to use powder detergent in this case.
This option is incompatible with the following wash
cycle: Speed wash and Baby cycle.
Delayed start
It is possible to delay the start time of the cycle for a period of
time between 1 and 24 hours.
1. After selecting the desired wash cycle and any other options,
press the DELAYED START button. The Delayed Start symbol
will begin to flash. Use the same button to select the time at which
you wish the wash cycle to begin (after a period of 1 to 24
hours).
2. Confirm the selection using the STAR/PAUSE button; the
symbol will stop flashing and the countdown will begin. The
text Start in will be displayed, the selected delay time
will flash and the START/PAUSE button will remain lit in a
fixed manner.
3. When the set time has elapsed, a long beep sounds,
the DELAYED START indicator light switches off and the
wash cycle begins.
To deselect the DLEAYED START option, press the DELAYED
START button repeatedly until the text OFF appears.
The Delayed Start function cannot be set once a wash
cycle has been started.
Short Time option
This option can be used to reduce the duration of the main wash
cycles while maintaining the same washing and drying perfor-
mance levels.
After selecting the wash cycle, press the Short Time option but-
ton; the illumination of the corresponding indicator light followed
by a short beep indicates its selection.
To deselect the option, press the same button again.
Good Night option
This option reduces the amount of noise made by the machine
and lengthens the wash cycles. It is a useful option because it
enables users to benefit from the night-time energy rate.
After selecting the wash cycle, press the Good Night option
button; the illumination of the corresponding indicator light fol-
lowed by a short beep indicates its selection.
To deselect the option, press the same button again.
Multi-functional tablets
This option optimises washing and drying results.
When using multi-functional tablets, press the MULTI-
FUNCTIONAL TABLETS button; the corresponding indicator
light will illuminate. If the button is pressed again the option will
be deselected.
The Multi-functional tablets option results in the
lengthening of the wash cycle.
The MULTI-FUNCTIONAL TABLETS option remains set
for subsequent wash cycles if it is not deselected.
The use of tablets is only recommended when the
MULTI-FUNCTIONAL TABLETS option is available.
This option is not recommended for use with wash cycles
which do not specify the use of multi-functional tablets
(see Table of options).
The Short Time and Good Night options are not
compatible with each other.
The Short Time and Good Night options are not
compatible with the HALF LOAD option.
Extra drying
To improve the dryness level of the crockery, press the
EXTRA DRYING button; the indicator light will illuminate. If it is
pressed again the option will be deselected.
The EXTRA DRYING option increases the duration of
the wash cycle.
SELFCARE WASH CYCLE
This disinfecting wash cycle deep cleans the inside of the
dishwasher, thereby reducing the formation of bad odours.
WARNING
The SELFCARE wash cycle should be performed as part of
your dishwasher maintenance routine, using special single-
dose products (follow the instructions on the packaging)
while the dishwasher is EMPTY.
A B C D E F
Table of
options
Delayed
Start
Half
Load
Tabs
Extra
Dry
Short
Time
Good
Night
Auto Super wash
Yes
Yes
Yes
Yes
Yes
No
Normal
Yes
Yes
Yes
Yes
Yes
Yes
Daily A 60’
Yes
Yes
Yes
No
No
No
Soaking
Yes
Yes
No
No
No
No
Eco 50°C
Yes
Yes
Yes
Yes
No
Yes
Speed 25’
Yes
No
Yes
NO
No
No
Crystals
Yes
Yes
Yes
Yes
No
No
Auto Duo Wash
Yes
No
Yes
Yes
Yes
No
Ultra Intensive
Yes
Yes
Yes
Yes
No
No
Special Guest
Yes
Yes
No
Yes
No
No
Baby Cycle
Yes
No
No
No
No
No
Self Care
Yes
No
No
No
No
No
- The machine will switch off automatically
during certain periods of inactivity, in order to
minimise electricity consumption.
EN
8
Wash cycles
For available OPTIONS please refer to the Table of options on the Start-up and use page.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Notes:
Optimum performance levels when using the "Daily A 60 and "Speed 25 cycles can be achieved by observing the maximum amounts
of crockery specified.
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5 ml of liquid
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less energy
and is les harmful to the environment.
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following
Detergent
(A) = compartment A
(B) = compartment B
Wash cycle selection instructions Wash cycle
Powder Liquid Tablets
Wash
cycles
which
include
drying
Options
Wash cycle
duration
(tolerance
±10%)
Hrs. Min.
Heavily soiled dishes and pans (not to be
used for delicate items).
Auto
Super Wash
35 g (A)
35 ml (A)
1 (A)
Yes
A-B-C-D-E
2:25
Normally soiled pans and dishes. Standard
daily wash cycle.
Normal
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Yes
A-B-C-D-
E-F
1:50
Limited quantity of daily soiling. (4 place
settings + 1 saucepan +1 frying pan).
Daily A 60
25 g (A)
25 ml (A)
1 (A)
No
A-B-C
1:00
Pre-wash for dishes while awaiting
completion of the load with the dishes from
the next meal.
Soaking
No
No
No
No
A B
0:08
Environmentally-friendly wash cycle with low
energy consumption levels, suitable for pans
and dishes.
Eco
* 50° C
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Yes
AB-C-D-F
2:55
Economic and fast wash to be used for lightly
soiled dishes. (Run cycle immediately after
use) (2 plates + 2 glasses + 4 pieces of
cutlery + 1 saucepan + 1 small frying pan).
Speed 25
25 g (A)
25 ml (A)
1 (A)
No
A - C
0:25
Economic and fast wash for delicate items
which are sensitive to high temperatures.
(Run cycle immediately after use) (glasses,
upper rack + delicate plates, lower rack ).
Crystals
35 g (A)
35 ml (A)
1 (A)
Yes
ABC-D
1:30
Wash spread over the two racks: delicate for
crystal and glasses on the upper rack and
heavy duty for the pans on the lower rack.
Auto
Duo Wash
35 g (A)
35 ml (A)
1 (A)
Yes
ACD-E
1:45
Heavily soiled saucepans or pans with
residual dried-on food.
Ultra
Intensive
35 g (A)
5 g (B)
35 ml (A)
5 ml (B)
1 (A)
1 (bottom
of the
appliance)
Yes
ABC-D
2:35'
Rinse and drying cycle for dishes that are
seldom used and are only dusty.
Special
Guest
No
No
No
Yes
AB D
0:32
Disinfecting wash cycle suitable for washing
bottles, rings and teats together with plates,
cups, glasses and cutlery. The crockery
should only be loaded on the upper rack.
Baby Cycle
20 g (A)
20 ml (A)
No
Yes
A
1:20'
Disinfecting cycle for cleaning the inside of
the dishwasher, to be carried out only when
the dishwasher is EMPTY using specific
detergents designed for dishwasher
maintenance.
SelfCare
No
No
No
No
A
0:40'
EN
9
Rinse aid and refined salt
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard
or very hard. Follow the instructions given on the
packaging.
If you do not add salt or rinse aid, the LOW
SALT
* and LOW RINSE AID* indicator lights
remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
When the LOW RINSE AID* indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the
lid (G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure it
does not overflow from the
dispenser. If this happens, clean the
spill immediately with a dry cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly
into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Switch on the appliance by pressing the ON/OFF button.
- Press the P button and hold for a few seconds; two short
beeps will sound, The text "WATER HARDNESS" will appear
on the display and the set hardness number will also flash
slowly on the display (the water softening system is set by
default to number 3).
- Press the DELAYED START button (levels 1 to 5) or the
HALF LOAD button (levels 5 to 1) repeatedly, until the
desired hardness level has been reached (1-2-3-4-5
*, see
hardness table). You will be able to scroll through a maximum
of 5 levels. Press the P button to confirm.
To exit the function, wait a few seconds or press one of the
option buttons
*, or switch off the machine using the ON/OFF
button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
 When the green float
* cannot be seen by simply looking at
the cap of the salt dispenser.
When the LOW SALT
* indicator light on the control panel is
illuminated;
1. Remove the lower rack and unscrew
the container cap (anticlockwise).
2. The first time you do this: fill the water
tank right up to its edge.
3. Position the funnel
* (see figure) and
fill the salt container right up to its edge
(this should hold approximately 1 kg); it is not unusual for a
little water to leak out.
4. Remove the funnel* and wipe any salt residue away from
the opening; rinse the cap under running water and then
screw it on, the head facing downwards so as to let the
water flow out of the four cracks which are arranged in a
star shape on the lower part of the cap. (the container cap
with the green float
*)
It is advisable to perform this procedure every time you
add salt to the container.
Make sure the cap is screwed on tightly, so that no
detergent can get into the container during the wash cycle
(this could damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
* Only available in selected models.
G
F
Water Hardness Table
°dH °fH mmol/l level
0 6 0 10 0 1 1
6 11 11 20 1.1 2 2
12 17 21 30 2.1 3 3
17 34 31 60 3.1 6 4
34 50 61 90 6.1 9
5
*
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
EN
10
Care and maintenance
Shutting off the water and electricity
supplies
Turn off the water tap after every wash cycle to avoid
leaks.
Always unplug the appliance when cleaning it and
when performing maintenance work.
Cleaning the dishwasher
The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
Preventing unpleasant odours
Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is
the main cause behind the formation of unpleasant
odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer
arms and block the holes used to spray the water. It is
therefore recommended that the arms are checked from
time to time and cleaned with a small non-metallic
brush.
The two sprayer arms may both be removed.
To remove the upper sprayer
arm, rotate the locking ring in
an anti-clockwise direction.
The upper sprayer arm should
be replaced with the holes
facing upwards.
The lower sprayer arm can be
removed by pressing on the
side tabs and pulling it
upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it
is clear and free of impurities before performing the
necessary connections. If this precaution is not taken,
the water inlet could become blocked and damage the
dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter
and clean it carefully under running water.
- Replace the filter and screw the water hose back into
position.
Cleaning the filters
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the
water. They should be cleaned if you wish to achieve the
best results in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters, or if the
filter is loose.
 After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using a
non-metallic brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
2. Remove the cup filter B by exerting a slight pressure on
the side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue.
NEVER REMOVE the wash cycle pump (black detail)
(fig. 4).
After cleaning the filters, replace the filter assembly and fix it
in position correctly; this is essential for maintaining the
efficient operation of the dishwasher.
Leaving the machine unused for extended
periods
Disconnect the appliance from the electricity supply and
shut off the water tap.
Leave the door of the appliance ajar.
When you return, run a wash cycle when the dishwasher is
empty.
* Only available in selected models.
2
C
B
4
1
3
EN
11
Precautions, advice
and Assistance
This appliance was designed and manufactured in
compliance with current international safety standards. The
following information has been provided for safety reasons
and should therefore be read carefully.
General safety
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
The appliance must be used by adults only, to wash
domestic crockery in accordance with the instructions in
this manual.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
machine exposed to rain and storms.
Do not touch the appliance when barefoot.
When unplugging the appliance always pull the plug from
the mains socket, do not pull on the cable.
The water supply tap must be shut off and the plug should
be removed from the electrical socket before cleaning the
appliance or carrying out any maintenance work.
If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt to
perform the repair work yourself.
Never touch the heating element.
Do not lean or sit on the open door of the appliance: this
may cause the appliance to overturn.
The door should not be left open as it may create a
dangerous obstacle.
Keep detergent and rinse aid out of reach of children.
The packaging material should not be used as a toy.
Disposal
Disposal of packaging materials: observe local legislation
so that the packaging may be reused.
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using the
normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection.
For further information relating to the correct disposal of
household appliances, owners may contact the relevant
public authority or the local appliance dealer.
Saving energy and respecting the
environment
Saving water and energy
Only begin a wash cycle when the dishwasher is full. While
waiting for the dishwasher to be filled, prevent unpleasant
odours using the Soak cycle (see Wash cycles).
Select a wash cycle which is suited to the type of crockery
and to the soil level of the crockery using the Table of wash
cycles:
- For dishes with a normal soil level, use the Eco wash
cycle, which guarantees low energy and water
consumption levels.
- If the load is smaller than usual activate the Half load
option
* (see Start-up and use).
If your electricity supply contract gives details of electricity
saving time bands, run wash cycles during the periods
when a lower tariff is applied. The Delayed start
* button
(see Start-up and use) helps you organise the wash cycles
accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
We strongly recommend that you use detergents that do
not contain phosphates or chlorine, as these products are
harmful to the environment.
Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with low-
temperature wash cycles in order to achieve the same
results as a normal 65°C wash cycle.
To avoid wasting detergent, use the product in appropriate
quantities based on the manufacturers recommendations,
the hardness of the water and the soil level and quantity of
crockery to be washed. Even if they are biodegradable,
detergents contain substances which may alter the balance
of nature.
Assistance
Before contacting Assistance:
Check whether the problem can be resolved using the
Troubleshooting guide (see Troubleshooting).
Restart the programme to check whether the problem has
ceased to exist.
If the problem persists, contact the Authorised Technical
Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
The type of malfunction.
The appliance model (Mod.).
The serial number (S/N).
This information can be found on the appliance data plate
(see Description of the appliance).
* Only available in selected models.
EN
12
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Problem: Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
The appliance has not been plugged in properly.
The dishwasher door has not been shut properly.
The door wont close The lock was released. Strongly push the door until a clacking noise is heard.
No water drains out from the
dishwasher.
The dishwasher cycle has not yet finished.
The water inlet hose is bent (see Installation).
The drain duct is blocked.
The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
The dishes are rattling against each other or against the sprayer arms.
An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
The lid on the salt dispenser is not closed properly.
The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
streaked or have a bluish tinge.
The rinse aid dosage is too high.
The crockery has not been dried
properly.
A wash cycle without a drying program has been selected.
The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
The rinse aid dispenser setting is not suitable.
The crockery is made from non-stick material or plastic.
The dishes are not clean. The racks are overloaded (see Loading the racks).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see Wash cycles).
An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
The lid on the rinse aid compartment has not been shut correctly.
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take any
water in - Tap shut-off alarm
(the ON/OFF indicator light flashes and
the following message appears on the
display: No water. Open tap. After a
few seconds, A:6 will appear).
There is no water in the mains supply.
The water inlet hose is bent (see Installation).
Turn on the tap and the appliance will start after a few minutes.
The appliance lock has been activated because no action was taken when the
beeps sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and switch
the appliance back on after 20 seconds by pressing the same button. Re-
program the appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet
filter blocked
(the ON/OFF indicator light flashes and
the display shows A:7).
Switch off the appliance by pressing the ON/OFF button. Shut off the water tap
to eliminate the risk of flooding and remove the plug from the electrical socket.
Make sure the water inlet filter has not become blocked by impurities (see Care
and maintenance chapter).
.4
13
Mode demploi
Sommaire
Installation, 14-15
Mise en place et mise à niveau
Raccordements eau et électricité
Conseils pour le premier lavage
Caractéristiques techniques
Description de lappareil, 16
Vue densemble
Tableau de bord
Charger les paniers, 17
Panier inférieur
Panier à couverts
Panier supérieur
Mise en marche et utilisation,18-19
Mettre en marche le lave-vaisselle
Charger le produit de lavage
Options de lavage
Programmes, 20
Tableau des programmes
Produit de rinçage et sel régénérant, 21
Charger le produit de rinçage
Charger le sel régénérant
Entretien et soin, 22
Coupure de larrivée deau et de courant
Nettoyer le lave-vaisselle
Eviter les mauvaises odeurs
Nettoyer les bras de lavage
Nettoyage du filtre dentrée deau
Nettoyer les filtres
En cas dabsence pendant de longues périodes
Précautions conseils et Service, 23
Sécurité générale
Mise au rebut
Economies et respect de lenvironnement
Service
Anomalies et remèdes, 24
Français, 13
FR
LDF 12314E
LAVE-VAISSELLE
.4
14
Installation
Conserver ce mode demploi pour pouvoir le consulter à
tout moment. En cas de vente, de cession ou de
déménagement, sassurer quil accompagne bien lappareil.
Lire attentivement les instructions: elles contiennent des
conseils importants sur linstallation, lutilisation
et la sécurité de lappareil.
En cas de déménagement, transporter lappareil
verticalement; si besoin est, lincliner sur le dos.
Cet appareil est conçu pour un usage domestique ou
autres applications similaires, telles que:
- lieux aménagés en espace cuisine pour le personnel de
magasins, bureaux et autres lieux de travail;
- fermes;
- utilisation par les clients d'hôtels, de motels ou autres locaux
de type résidentiel;
- chambres d'hôtes.
Mise en place et mise à niveau
1. Déballer lappareil et sassurer quil na pas été endommagé
pendant le transport.
Sil est abîmé, ne pas le raccorder et contacter le revendeur.
2. Installer le lave-vaisselle de manière à ce que les côtés et la
paroi arrière touchent aux meubles adjacents ou au mur.
Lappareil peut être encastré sous un plan de travail continu
*
(voir feuille de Montage).
3. Installer le lave-vaisselle sur un sol plat et rigide.
Compenser les irrégularités en vissant ou en dévissant les
pieds avant jusquà ce que lhorizontalité de lappareil soit
parfaite. Une bonne horizontalité garantit la stabilité de
lappareil et supprime tout risque de vibrations, bruits et
déplacements.
4
*. Pour régler la hauteur du pied arrière, agir sur la douille
rouge à six pans située dans la partie avant du lave-vaisselle,
en bas et au milieu, à laide dune clé mâle à six pans,
ouverture 8 mm. Tourner dans le sens des aiguilles dune
montre pour augmenter la hauteur et dans le sens inverse
pour la diminuer. (consulter la notice dinstructions encastré
jointe à la documentation)
Raccordements eau et électricité
Ladaptation des installations électriques et les travaux de
plomberie de linstallation doivent être effectués par du
personnel qualifié.
Le lave-vaisselle ne doit pas écraser les tuyaux ou le
câble dalimentation électrique.
Utiliser des tuyaux neufs pour effectuer le raccordement
de lappareil au réseau de distribution de leau.
Ne pas réutiliser les anciens tuyaux.
Les tuyaux damenée et dévacuation de leau et le câble
dalimentation électrique peuvent être orientés vers la droite ou
vers la gauche pour simplifier linstallation
.
Raccord du tuyau damenée de leau
A une prise deau froide: bien visser le tuyau damenée à un
robinet à embout fileté 3/4 gaz; avant de visser, faire couler
leau jusquà ce quelle devienne limpide et dépourvue
dimpuretés qui pourraient engorger lappareil.
A une prise deau chaude: en cas dinstallation de
chauffage centralisé (radiateurs), le lave-vaisselle peut être
alimenté avec de leau chaude de réseau ne dépassant
pas 60°C.
Visser le tuyau au robinet en procédant comme pour la
prise deau froide.
Si la longueur du tuyau damenée ne suffit pas,
sadresser à un magasin spécialisé ou à un technicien agréé
(voir Assistance).
La pression de leau doit être comprise entre les valeurs
reportées dans le tableau des Caractéristiques techniques (voir
ci-contre).
Faire attention à ce que le tuyau ne soit ni plié ni écrasé.
Raccordement du tuyau d'évacuation de l'eau
raccorder le tuyau d'évacuation, sans le plier, à une
conduite d'évacuation ayant au moins 4 cm de
diamètre.
Le tuyau d'évacuation doit être placé entre 40 et 80 cm
au-dessus du sol ou du plan d'appui du lave-vaisselle
(A).
Avant de raccorder le tuyau d'évacuation de l'eau au
siphon de l'évier, retirer le bouchon en plastique (B).
* Présent uniquement sur certains modèles.
.4
15
Sécurité anti-fuite
Pour éviter tout risque dinondation, le lave-vaisselle:
- est équipé dun dispositif qui coupe larrivée de leau en cas
danomalie ou de fuite à lintérieur de lappareil.
Quelques modèles sont équipés dun dispositif de sécurité
supplémentaire New Acqua Stop
* qui garantit contre tout
risque dinondation même en cas de rupture du tuyau
damenée de leau.
ATTENTION: TENSION DANGEREUSE!
Il ne faut en aucun cas couper le tuyau damenée de leau car il
contient des parties sous tension.
Raccordement électrique
Avant de brancher la fiche dans la prise de courant, sassurer
que:
la prise dispose de mise à la terre et est conforme aux
normes;
la prise est bien apte à supporter la puissance maximale
de lappareil reportée sur la plaque signalétique fixée à la
contre-porte (voir paragraphe Description du lave-
vaisselle);
la tension dalimentation est bien comprise entre les valeurs
figurant sur la plaque signalétique de la contre-porte;
la prise est bien compatible avec la fiche de lappareil.
Autrement, faire remplacer la fiche par un technicien agréé
(voir Assistance); nutiliser ni rallonges ni prises multiples.
Après installation de lappareil, le câble dalimentation
électrique et la prise de courant doivent être facilement
accessibles.
Le câble ne doit être ni plié ni trop écrasé.
Afin déviter tout danger, faire changer le cordon dalimen-
tation abîmé, par le fabricant ou par son service après-vente.
(Voir Assistance)
Nous déclinons toute responsabilité en cas de non-
respect des normes énumérées ci-dessus.
Ruban anti-condensation*
Après avoir encastré le lave-vaisselle, ouvrir la porte et coller
le ruban adhésif transparent sous le plan en bois pour le
protéger contre la formation de condensation.
Conseils pour le premier lavage
Une fois linstallation terminée et tout de suite avant le premier
lavage, remplir complètement deau le réservoir à sel et ajouter
environ 1 kg de sel (voir Produit de rinçage et sel régénérant)
: il est tout à fait normal que de leau déborde. Sélectionner le
degré de dureté de leau (voir Produit de rinçage et sel
régénérant). - Après remplissage du réservoir à sel, le voyant
SEL
* s'éteint.
Le manque de remplissage du réservoir à sel, peut
endommager l'adoucisseur d'eau et l'élément chauffant.
* Présent uniquement sur certains modèles.
Caractéristiques techniques
Dimensions
largeur 60 cm
hauteur 85 cm
profondeur 60 cm
Capacité 14 couverts standard
Pression eau
d’alimentation
0,05 ÷ 1 MPa (0,5 ÷ 10 bar)
7,25 – 145 psi
Tension
d’alimentation
Voir étiquette des caractéristiques
Puissance totale
absorbée
Voir étiquette des caractéristiques
Fusible Voir étiquette des caractéristiques
Cet appareil est conforme aux
Directives Communautaires
suivantes:
- 2006/95/EC (Basse Tension)
- 2004/108/EC (Compatibilité
Electromagnétique)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Etiquetage)
-2002/96/EC (DEEE)
.4
16
Vue densemble
Description de
lappareil
1. Panier supérieur
2. Bras de lavage supérieur
3. Clayettes rabattables
4. Réglage hauteur du panier
5. Panier inférieur
6. Bras de lavage inférieur
7. Panier à couverts
8. Filtre lavage
9. Réservoir à sel
10. Bacs produit de lavage et réservoir à
produit de rinçage
11. Plaque signalétique
12. Tableau de bord
***
*** Uniquement pour modèles tout intégrables.
* Présent uniquement sur certains modèles.
Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.
Tableau de bord
Touche Sélection de programme
Touche Pastilles
multifonction
Touche
Départ différé
Voyant
Demi-charge Supérieur/inférieur
Voyant ON-OFF
Voyant
Manque de sel
Voyant Manque de
produit de rinçage
Touche option
GoodNight
Touche et voyant
Marche/Arret
Indicateur lumineux du temps restant
Touche
ON-OFF/RESET
Touche
Demi-charge
Voyant pastilles
multifonction
Voyant
Départ différé
Voyant option GoodNight
Touche
Séchage Super
Voyant Séchage Super
Touche option
Short Time
Voyant option Short Time
Indicateur lumineux du
nom du programme
.4
17
Charger les paniers
Avant de charger les paniers, débarrasser la vaisselle des
déchets plus importants et vider les verres et les coupes.
Après avoir chargé le lave-vaisselle, sassurer que les bras
de lavage tournent librement.
Panier du bas
Le panier du bas peut contenir des casseroles, des
couvercles, des assiettes, des saladiers, des couverts
etc.selon les Exemples de chargement.
Ranger de préférence sur les côtés du panier les plats de
service et les grands couvercles sans toutefois bloquer la
rotation du bras de lavage supérieur.
Certains modèles de
lave-vaisselle sont
pourvus de secteurs
rabattables
* qui
peuvent être placés
à la verticale pour ranger des assiettes ou à lhorizontale pour
ranger des casseroles et des saladiers.
Panier à couverts
Le panier à couverts peut varier selon le modèle de lave-
vaisselle : séparable, non séparable, coulissant. Le panier à
couverts non séparable doit être placé obligatoirement dans
la partie avant du panier inférieur.
Le panier séparable
se détache en deux
parties, solution
pratique en cas de
lavage d'une demi-
charge (si cette
option est prévue pour le modèle de lave-vaisselle), il peut
coulisser parmi les accessoires fixes ou rabattables pour aller
se placer dans n'importe quel coin du panier du bas.
- Ils sont équipés tous deux de rabats coulissants qui
permettent de mieux ranger les couverts.
Ranger les couteaux et les ustensiles de cuisine pointus et
coupants dans le panier à couverts, pointes tournées vers le
bas, ou, à plat, sur les clayettes rabattables du panier
supérieur.
Exemples de rangement dans le panier à couverts
Panier du haut
Y ranger la vaisselle fragile et légère : verres, tasses à thé et à
café, soucoupes, saladiers bas, casseroles basses peu sales,
en suivant les Exemples de chargement.
Tasses et tasses à café, couteaux longs et pointus, couverts
de service: les placer sur les étagères rabattables
**.
Etagères rabattables à inclinaison variable*
- L'inclinaison permet de gagner de la place dans le panier
supérieur, de ranger des verres à pied de longueur différente
et d'améliorer les performances de séchage.
- Soulever l'étagère rabattable, la faire glisser légèrement et la
placer selon l'inclinaison désirée.
Régler la hauteur du panier supérieur
Pour optimiser le rangement de la vaisselle, possibilité de régler le
panier supérieur en position haute ou basse:
(pour les modèles équipés de cycle Baby, placer le panier
supérieur en position basse pour procéder à des chargements
Baby).
Régler de préférence la hauteur du panier quand ce
dernier est VIDE.
Ne jamais soulever ou abaisser le panier dun seul côté.
Ouvrir les butées des glissières du
panier à droite et à gauche et sortir le
panier. Positionner le panier en position
haute ou basse, le faire glisser le long
des glissières jusquà ce que les roues
avant entrent elles aussi et refermer les
butées (voir figure).
Si le panier est équipé de poignées
Espace double
* (voir figure), sortir le
panier du haut en fin de corse, saisir les
poignées sur les côtés du panier et
déplacer vers le haut ou vers le bas;
laisser retomber le panier sans le lâcher.
Exemples de chargement du panier supérieur/
inférieur
Etagères rabattables Baby
*
Les modèles de lave-vaisselle avec Cycle
Baby sont fournis équipés détagères
rabattables spéciales pour le lavage de
biberons, bagues et tétines. (voir feuille
d'instructions jointe à la documentation)
Vaisselle nallant pas au lave-vaisselle
Objets en bois, avec des manches en bois ou en corne ou
ayant des parties collées.
Objets en aluminium, cuivre, laiton ou étain.
Vaisselle en plastique thermorésistant.
Porcelaines anciennes ou peintes à la main.
Argenterie ancienne. Les pièces dargenterie non ancienne
peuvent par contre être lavées avec un programme délicat
après sêtre assuré quelles ne touchent pas à dautres métaux.
Nous conseillons dutiliser de la vaisselle lavable au lave-
vaisselle.
* Présent uniquement sur certains modèles.
** Leur nombre et leur position varient.
Inclinaison A Inclinaison B Inclinaison C
.4
18
Mise en marche et
utilisation
Charger le produit de lavage
Un bon résultat de lavage dépend aussi dun bon dosage
du produit de lavage. Un excès de produit de lavage ne
lave pas mieux et pollue lenvironnement.
Nutiliser que du produit de lavage spécial lave-
vaisselle.
NE PAS UTILISER de produits pour laver la vaisselle à
la main.
Une utilisation excessive de produit de lavage peut
laisser des résidus de mousse en fin de cycle.
L'utilisation de pastilles n'est conseillée que pour les
modèles qui prévoient l'option PASTILLES
MULTIFONCTION.
Pour obtenir des performances de lavage et de
séchage optimales, utiliser des produits de lavage en
poudre, du liquide de rinçage et du sel.
bac A: Produit de lavage
bac B: Produit de prélavage
1. Appuyer sur la touche D pour
ouvrir le couvercle C.
2. Pour doser le produit de lavage se
reporter au Tableau des
programmes:
en poudre : bacs A et B.
pastilles: si le programme en
prévoit 1, placer cette dernière dans
le bac A et fermer le couvercle; sil en
prévoit 2, mettre la deuxième dans le fond de la cuve.
3. Eliminer les résidus de produit de lavage sur les bords du
bac et fermer le couvercle jusquau déclic.
* Présent uniquement sur certains modèles.
Première mise en service
Choisir la langue
Appuyer sur ON/OFF, un bip bref retentit et la langue sélectionnée
saffiche.
Faire défiler la liste des langues, à laide de la touche DÉPART
DIFFÉRÉ pour avancer et celle de DEMI-CHARGE pour revenir
en arrière, jusquà la langue voulue. Appuyer sur la touche P
pour confirmer et entrer automatiquement dans la liste des
programmes de lavage.
A chaque allumage qui suit la première mise en service, le lave-
vaisselle affiche la liste des programmes.
Pour modifier le choix de la langue après la première mise en
service, il suffit dappuyer simultanément pendant quelques
secondes sur la touche P et sur la touche de DÉPART DIFFÉRÉ.
Mettre en marche le lave-vaisselle
1. Ouvrir larrivée deau.
2. Appuyer sur la touche ON-OFF : un bip court retentit, le
voyant ON/OFF et lafficheur sallument.
3. Ouvrir la porte et doser le produit de lavage (voir plus bas).
4. Charger les paniers (voir Charger les paniers) et fermer la
porte.
5. Pour sélectionner le programme selon le type de vaisselle et
son degré de salissure (voir tableau des programmes)
,
appuyer sur la touche P.
6. Sélectionner les options de lavage (voir ci-contre).
7. Appuyer sur la touche Marche pour faire démarrer le lavage :
un bip prolongé signale le démarrage du programme et le nom
du programme sélectionné ainsi que le temps de lavage restant
saffichent.
8. A la fin, deux bips courts et un bip prolongé annoncent la fin
du programme et le message FIN DE CYCLE saffiche à lécran.
Eteindre lappareil par pression sur la touche ON-OFF, fermer
le robinet de leau et débrancher la fiche de la prise de courant.
9. Attendre quelques minutes avant de sortir la vaisselle pour
éviter de se brûler. Décharger les paniers en commençant par
celui du bas.
PROGRAMMES AUTO
*: grâce à un capteur spécial, ce
modèle de lave-vaisselle peut évaluer le degré de salissure et
sélectionner le lavage le plus efficace et le plus économique.
La durée des programmes automatiques peut varier du fait de
lintervention du capteur.
En cas de vaisselle peu sale ou précédemment rincée à
leau, réduire considérablement la quantité de produit de
lavage.
Modifier un programme en cours
En cas derreur de sélection dun programme, il est possible de
le modifier, à condition quil vienne tout juste de démarrer : pour
changer un cycle de lavage en cours, éteindre puis rallumer
lappareil par une pression prolongée sur la touche ON/OFF,
sélectionner ensuite le nouveau programme et les options
désirées.
Introduire de la vaisselle en cours de lavage
Appuyer sur la touche Marche/Pause, (la touche se met à
clignoter). Ouvrir la porte en faisant attention à la vapeur
chaude qui séchappe et introduire la vaisselle. Appuyer sur la
touche Marche/Pause (lumière fixe): le cycle repart après un
bip prolongé.
Appuyer sur la touche Marche/Pause pour mettre lappareil
en pause, le programme et le départ différé éventuellement
sélectionné sont stoppés.
Pendant cette phase, aucun changement de programme nest
possible.
Interruptions accidentelles
En cas douverture de la porte en cours de lavage ou de
coupure de courant, le programme sarrête. Il redémarre du
point il a été interrompu dès que le courant revient ou que la
porte est refermée.
Options de lavage*
La sélection, la modification ou lannulation des OPTIONS nest
possible quaprès avoir choisi le programme de lavage et
avant dappuyer sur la touche Marche/Pause.
Seules les options compatibles avec le programme choisi peuvent
être sélectionnées. Si une option nest pas compatible avec le
programme sélectionné, (voir tableau programmes) la led
correspondante clignote 3 fois de suite et 2 bips courts
retentissent.
En cas de sélection dune option incompatible avec une option
précédemment sélectionnée, celle-ci clignote 3 fois de suite, 3
bips retentissent puis elle séteint, tandis que la dernière sélection
effectuée reste allumée.
Pour désactiver une option sélectionnée par erreur, appuyer à
nouveau sur la touche correspondante.
.4
19
* Présent uniquement sur certains modèles.
Pastilles Multifonction
Cette option permet doptimiser le résultat de lavage et de
séchage.
En cas dutilisation de pastilles multifonction, appuyer sur la
touche PASTILLLES MULTIFONCTION qui sallume. Pour
désactiver cette option appuyer à nouveau sur la touche.
Loption Pastilles Multifonction prolonge la durée du
programme.
Loption pastilles multifonction reste mémorisée lors
des allumages suivants de lappareil à moins quelle nait
été désactivée.
Lutilisation de pastilles nest conseillée quen
présence de loption PASTILLES MULTIFONCTION.
Cette option est déconseillée pour les programmes qui
ne prévoient pas lutilisation de pastilles multifonction
(voir tableau des options).
Option Short Time
Cette option permet de réduire la durée des principaux
programmes tout en assurant les mêmes performances de
lavage et de séchage
Après avoir sélectionné le programme, appuyer sur la
touche Option Short Time, lallumage du voyant et un bip
court annoncent que la sélection a eu lieu.
Pour désactiver cette option, appuyer à nouveau sur la
même touche.
Les Options Short Time et Good Night ne sont
pas compatibles entre elles.
Les Options Short Time et Good Night ne sont
pas compatibles avec loption DEMI-CHARGE.
Option Good Night
Cette option permet un fonctionnement encore plus silencieux
en prolongeant la durée des programmes, idéale car elle permet
de profiter du tarif électricité nocturne.
Après avoir sélectionné le programme, appuyer sur la touche
Option Good Night, lallumage du voyant et un bip court
annoncent que la sélection a eu lieu.
Pour désactiver cette option, appuyer à nouveau sur la même
touche.
Séchage super
Pour améliorer le séchage de la vaisselle, appuyer sur la touche
SÉCHAGE SUPER qui sallume. Pour désactiver loption
appuyer une nouvelle fois.
Loption SÉCHAGE SUPER prolonge la durée du
programme.
PROGRAMME AUTO-NETTOYAGE
Ce programme de lavage spécial pour lhygiène intérieure du
lave-vaisselle permet de le laver à fond et de réduire ainsi la
formation de mauvaises odeurs.
Demi-charge panier supérieur ou inférieur
Le programme demi-charge permet de laver une petite
vaisselle et de faire des économies deau, délectricité et de
produit de lavage. Sélectionner le programme, appuyer sur la
touche DEMI-CHARGE: le triangle correspondant à la charge
choisie sallume et le lavage nest lancé que dans le panier
supérieur ou que dans le panier inférieur. Pour désactiver
cette option appuyer à nouveau sur la touche.
La demi-charge nest pas compatible avec lOption Good
Night et avec lOption Short Time.
Penser à ne ranger la vaisselle que dans le panier
supérieur ou inférieur et à réduire de moitié la quantité de
produit de lavage.
Mieux vaut utiliser un produit de lavage en poudre.
Cette option nest pas utilisable avec le programme:
Rapide.
Départ différé
Possibilité de différer le départ du programme de 1 à 24 heures:
1. après avoir sélectionné le programme de lavage et toute autre
option possible, appuyer sur la touche DÉPART DIFFÉRÉ: le
symbole du Départ différé se mettra à clignoter. Sélectionner à
laide de la même touche à quel moment on veut faire démarrer
le cycle de lavage (de 1 à 24 heures).
2. Confirmer son choix à laide de la touche MARCHE/PAUSE, le
symbole cesse de clignoter, le compte à rebours commence et le
message Démarrage...saffiche, le retard sélectionné clignote et
la touche MARCHE/PAUSE cesse de flasher (lumière fixe).
3. A lexpiration du délai dattente, un bip prolongé retentit, le
voyant du DÉPART DIFFÉRÉ séteint et le programme démarre.
Pour désactiver un DÉPART DIFFÉRÉ, appuyer sur la touche
DÉPART DIFFÉRÉ jusquà affichage de OFF.
Aucune sélection de Départ différé nest plus possible
en cours de cycle.
ATTENTION
Le programme de lavage AUTO-NETTOYAGE doit être
effectué à vide et avec des produits dentretien
spéciaux lave-vaisselle monodose (se conformer aux
instructions reportées sur lemballage).
A B C D E F
Tableau des
options
Départ
différé
Demi-
charge
Pastilles
Multifonction
Séchage
Super
Short
Time
Good
Night
Super lavage
Oui
Oui
Oui
Oui
Oui
Non
Normal
Oui
Oui
Oui
Oui
Oui
Oui
Quotidien A 60
Oui
Oui
Oui
Non
Non
Non
Trempage
Oui
Oui
Non
Non
Non
Non
Eco 50°C
Oui
Oui
Oui
Oui
Non
Oui
Rapide 25
Oui
Non
Oui
Non
Non
Non
Cristal
Oui
Oui
Oui
Oui
Non
Non
Duo Wash
Oui
Non
Oui
Oui
Oui
Non
Intensive
Oui
Oui
Oui
Oui
Non
Non
Special Invité
Oui
Oui
Non
Oui
Non
Non
Cycle Bébé
Oui
Non
Non
Non
Non
Non
Auto-Nettoyage
Oui
Non
Non
Non
Non
Non
- Pour réduire sa consommation d'énergie, la
machine s'éteint automatiquement dans certaines
conditions de non-utilisation.
.4
20
Programmes
En cas de vaisselle peu sale ou précédemment rincée à leau, réduire considérablement la quantité de produit de lavage.
Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.
Remarques:
Pour obtenir des performances optimales avec les programmes "Quotidien et Rapide 25" il est conseillé de respecter le nombre de
couverts indiqué.
* Le programme Eco est conforme à la norme EN-50242. Il a une durée de lavage plus longue que les autres programmes mais
cest aussi celui qui consomme le moins dénergie et qui respecte le plus lenvironnement.
Note pour les laboratoires d'essai: pour toutes informations détaillées sur les conditions d'essai comparatif EN, s'adresser à :
Pour simplifier le dosage du produit de lavage, prendre note que:
1 cuillère à soupe = 15 gr. de poudre = 15 ml de liquide environ - 1 cuillère à café = 5 gr. de poudre = 5 ml de liquide environ
Produit de lavage
(A) = bac A
(B) = bac B
Indications sur le choix des
programmes
Programme
Poudre Liquide Pastilles
Programmes
prévoyant le
séchage
Options
Durée du
programme
(tolérance
±10% Hrs. Min
Vaisselle et casseroles très sales
(déconseillé pour la vaisselle
fragile).
Super
Lavage
35 g (A)
35 ml (A)
1 (A)
Oui
A-B-C-D-
E
2:25
Vaisselle et casseroles
normalement sales. Programme
standard quotidien.
Normal
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A) Oui
A-B-C-D-
E-F
1:50
Vaisselle du jour en quantité
réduite. (4 couverts + 1 casserole +
1 poêle).
Quotidien 60
25 g (A)
25 ml (A)
1 (A)
Non
A-B-C
1:00
Lavage préalable dans lattente de
compléter le chargement au repas
suivant.
Trempage
Non
Non
Non
Non
A - B 0:08
Lavage écologique à faible
consommation d’électricité pour
vaisselle et casseroles.
Eco
* 50°C
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Oui
A-B-C-D-
F
2:55
Cycle économique et rapide pour
vaisselle peu sale, tout de suite
après lusage. (2 assiettes +2
verres +4 couverts +1 casserole +
1 petite poêle)
Rapide 25
25 g (A)
25 ml (A)
1 (A)
Non
A - C
0:25
Cycle économique et rapide pour
vaisselle fragile ne supportant pas
les hautes températures, tout de
suite après lusage. (verres à pied
panier supérieur + assiettes fragiles
panier inférieur).
Cristal
35 g (A)
35 ml (A)
1 (A)
Oui
A-B-C-D
1:30
Lavage différencié dans les deux
paniers : délicat dans celui du haut
pour verres et cristal, énergique
dans celui du bas pour les
casseroles.
Duo Wash
35 g (A)
35 ml (A)
1 (A)
Oui
A-C-D-E
1:45
Casseroles extrêmement sales ou
avec incrustations daliments.
Ultra Intensif
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
1 (fond de
cuve)
Oui
A-B-C-D
2:35
Cycle de rinçage et de séchage
pour vaisselle peu utilisée; à
dépoussiérer seulement.
Special Invité
Non
Non
Non
Oui
A-B-D
0:32
Cycle de lavage pour lhygiène des
biberons, bagues, tétines, lavés en
même temps quassiettes, tasses,
verres et couverts. Charger
uniquement le panier du haut.
Cycle Bébé
20 g (A)
20 ml (A)
Non
Oui
A
1:20
Cycle de lavage spécial pour
lhygiène intérieure du lave-
vaisselle à utiliser à VIDE avec
des produits dentretien
spéciaux lave-vaisselle.
Auto
Nettoyage
Non
Non
Non
Non
A
0:40
1 / 1

Hotpoint LDF 12314E Omaniku manuaal

Kategooria
Nõudepesumasinad
Tüüp
Omaniku manuaal
See käsiraamat sobib ka