Hotpoint LDF 12314E Omaniku manuaal

Kaubamärk: Hotpoint

Mudel: LDF 12314E

Kategooria: Nõudepesumasinad

Tüüp: Omaniku manuaal

See juhend sobib ka

Operating instructions

Contents

Installation, 2-3

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Description of the appliance, 4

Overall view

Control panel

Loading the racks, 5

Lower rack

Cutlery basket

Upper rack

Start-up and use, 6-7

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 8

Table of wash cycles

Rinse aid and refined salt, 9

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 10

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Precautions, advice and Assistance,11

General safety

Disposal

Saving energy and respecting the environment

Assistance

Troubleshooting, 12

English,1

LDF 12314E

DISHWASHER

Français, 13

Español, 49

Deutsch, 25

Português, 61

Polski, 73

Nederland, 37

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved,

please ensure the manual is kept with the machine, so that the

new owner may benefit from the advice contained within it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

This appliance is intended to be used in household and

similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check that it

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with the

wall. This appliance can also be recessed under a single

worktop

* (see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be adjusted

until it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move or

cause vibrations and noise while it is operating.

* Adjust the height of the rear foot from the front of the

appliance* on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an

anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should

only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity supply

cable may be positioned towards the right or the left in order

to achieve the best possible installation.

Connecting the water inlet hose

 To a suitable cold water connection point: before attaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded connection.

 To a suitable hot water connection point: your dishwasher

may be supplied with hot water from the mains supply (if

you have a central heating system with radiators) provided

that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician (see Assistance).

The water pressure must be within the values indicated in

the Technical data table (see adjacent information).

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to

80 cm from the floor / surface where the dishwasher

rests (A).

Before connecting the water outlet hose to the sink

drain, remove the plastic plug (B).

* Only available in selected models.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate located on

the inside of the door (see chapter entitled Description of

the appliance).

 The power supply voltage falls within the values indicated

on the data plate on the inside of the door.

 The socket is compatible with the plug of the appliance. If

this is not the case, ask an authorised technician to replace

the plug (see Assistance); do not use extension cables or

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards. (See Assistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add only then approximately 1 kg of salt (see

chapter entitled Rinse aid and refined salt). The water may

overflow: this is normal and is not a cause for concern. Select

the water hardness value (see chapter entitled Rinse aid and

refined salt).

- After the salt has been poured into the

machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener and the

heating element may be damaged as a result.

* Only available in selected models.

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity 14 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2005/32/EC (Comm. Reg.

1275/2008) (Ecodesign)

-97/17/EC (Labelling)

-2002/96/EC Waste Electrical

and Electronic Equipment

(WEEE)

Overall view

Description of the

appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel

***

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

Low rinse aid

indicator light

ON/OFF/Reset

button

Half load button

Delayed start button

Extra Dry button

Wash cycle name

indicator light

ON/OFF

indicator light

Low salt

indicator light

Select wash

cycle button

Multi-functional tablets

indicator light

Short Time option

indicator light

Good Night option

indicator light

Extra Dry indicator light

Half load upper and

lower rack indicator

lights

Time remaining

light-up display

Start/Pause

button and

indicator light

Multi-functional

tablets button

Option button

Short Time

Good Night

option button

Delayed start

indicator light

Loading the racks

Before loading the racks, remove all food residues from

the crockery and empty liquids from glasses and cups.

After loading the appliance, check that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, plates, salad bowls,

cutlery, etc. as seen in the Loading examples.

Plates and large covers should be placed at the sides of the

rack, ensuring that they do not block the rotation of the upper

sprayer arm.

Some dishwasher

models are fitted

with tip-up

sections

*, which

can be used in a

vertical position

when arranging plates or in a horizontal position when

arranging pans and salad bowls.

Cutlery basket

The type of cutlery basket may vary according to the

dishwasher model: it may be modular, non-modular or a sliding

version. The non-modular basket must only be positioned at

the front of the lower rack.

The modular basket

may be separated into

two parts, a solution

which is recommended

when performing a half

load wash (only in models offering this option), is available in a

sliding version (positioned at any point on the lower rack by

sliding it between the fixed or tip-up inserts.

- Both versions are fitted with a collapsible sliding system which

means the cutlery can be arranged in the best possible way.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards, or they

must be positioned horizontally in the tip-up compartments on

the upper rack.

Cutlery basket positioning examples

Upper rack

Load this rack with delicate and lightweight crockery:

glasses, tea and coffee cups, saucers, small salad bowls,

saucepans and small saucepans which are not too soiled,

using the Loading examples as a guide.

 Mugs and cups, long sharp knives and serving utensils:

place these on the tip-up compartments

**.

Tip-up compartments with adjustable tilt*

- The tilt feature can be used to increase the space in the upper

rack, to position wine glasses with different stem lengths safely

and to improve drying performance.

- Lift the tip-up compartment, slide it gently and position it in the

desired tilt angle.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper

rack may be moved to a higher or lower level.

(in models which offer the Baby cycle, the upper rack must be

placed in its lower position when the appliance is being loaded).

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

Never lift or lower the rack on one side only.

Open the left and right guide rail stops

and pull out the rack; position it higher or

lower as required, slide it along the guide

rails until the front wheels are in place and

close the stops (see figure).

If the rack is fitted with Dual Space

handles

* (see figure), pull out the upper

rack until it reaches its stop point, grip the

handles at the sides of the rack and move it

upwards or downwards, then slowly let it

fall back into place.

Loading examples for the upper/lower rack

Baby Tip-up compartments

For dishwasher models with a Baby Cycle,

tip-up compartments suitable for washing

bottles, rings and teats are provided. (see

the instruction sheet)

Items which should not be washed in the

dishwasher

 Wooden items, objects with wooden or horn handles or glued-

on parts.

 Items made from aluminium, copper, brass, pewter or tin.

 Items made from plastic material which is not heat-resistant.

 Antique or hand-painted porcelain.

 Antique silver. Silver which is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other metals.

We recommend the use of crockery which is dishwasher safe.

* Only available in selected models.

** The number and position may vary.

Tilt A Tilt B Tilt C

Start-up and use

* Only available in selected models.

Switching the appliance on for the first time

Selecting the language

Press the ON/OFF symbol; you will hear a short beep and the

display will show the set language.

Use the DELAYED START button to scroll forwards, or the HALF

LOAD button to scroll backwards through the list until you reach

the desired language. Press the P button to confirm the selection;

you will then automatically enter the list of wash cycles.

Every time the dishwasher is switched on subsequently, the list

of wash cycles will be displayed.

The language may also be changed at a later date, by pressing

the P button and the DELAYED START button simultaneously for

a few seconds.

Starting the dishwasher

1. Turn the water tap on.

2. Press the ON/OFF button: you will hear a short beep and

the display will light up.

3. Open the door and pour in a suitable amount of detergent

(see below).

4. Load the racks (see Loading the racks) and shut the door.

5. Select the wash cycle in accordance with the type of

crockery and its soil level (see Table of wash cycles) by

pressing the P button.

6. Select the wash options (see adjacent information).

7. Start the cycle by pressing the Start button: a long beep

signals the start of the wash cycle; the name of the selected

cycle is displayed, along with the time remaining until the end

of the cycle.

8. Two short beeps and one long one indicate the end of the

wash cycle and the text CYCLE END appears on the

display. Switch off the appliance by pressing the ON/OFF

button, shut off the water valve and unplug the appliance from

the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

AUTO WASH CYCLES

*: this model of dishwasher is

equipped with a special sensor which can be used to assess

the level of soiling and automatically select the most efficient

and economic wash cycle accordingly.

The duration of the auto wash cycles may vary due to the

operation of the sensor.

If the crockery is only lightly soiled or if it has been

rinsed with water before being placed in the dishwasher,

reduce the amount of detergent used accordingly.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it has

only just begun: once the wash cycle has started, switch off

the machine by pressing and holding the ON/OFF/Reset

button. Switch it back on using the same button and select the

desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding indicator light

will flash). Open the door, taking care to avoid the escaping

steam, and place the crockery inside the appliance. Press the

Start/Pause button (fixed light): the cycle will restart after a

prolonged beep is emitted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start function (if

selected) is interrupted.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

Measuring out the detergent

A good wash result also depends on the correct amount

of detergent being used; exceeding the stated amount

does not result in a more effective wash and increases

environmental pollution.

Only use detergent which has been specifically

designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle has

ended.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid liquid

and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button D.

2. Pour in the detergent after consulting

the Table of wash cycles:

 For powder detergent use

compartments A and B.

 For detergent in tablet form: when the

cycle requires 1 tablet, place it in

compartment A and close the cover;

when it requires 2, place the second

tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Wash options*

The OPTIONS may only be set, modified or reset after the

wash cycle has been selected and before the Start/

Pause button has been pressed.

Only the options which are compatible with the type of wash

cycle set may be selected. If an option is not compatible with the

selected wash cycle (see Table of wash cycles), the correspond-

ing LED flashes rapidly 3 times and 2 short beeps will sound.

If an option is selected which is incompatible with another (previ-

ously selected) option, the indicator light corresponding to the

option selected first will flash 3 times, 3 beeps will sound and it will

be deselected, while the most recently selected option will remain

active.

To deselect an option which has been set by mistake, press the

corresponding button again.

* Only available in selected models.

Half load using the upper or lower rack

If there are not many dishes to be washed, a half load cycle

may be used in order to save water, electricity and detergent.

Select the wash cycle and press the HALF LOAD button

repeatedly: the triangle corresponding to the selected load will

illuminate and the wash cycle will take place only using the

upper or lower rack. If the button is pressed again, the option

will be deselected.

The Half Load option is not compatible with the Good

Night and Short Time options.

Remember to load the upper or lower rack only, and to

reduce the amount of detergent accordingly.

It is better to use powder detergent in this case.

This option is incompatible with the following wash

cycle: Speed wash and Baby cycle.

Delayed start

It is possible to delay the start time of the cycle for a period of

time between 1 and 24 hours.

1. After selecting the desired wash cycle and any other options,

press the DELAYED START button. The Delayed Start symbol

will begin to flash. Use the same button to select the time at which

you wish the wash cycle to begin (after a period of 1 to 24

hours).

2. Confirm the selection using the STAR/PAUSE button; the

symbol will stop flashing and the countdown will begin. The

text Start in will be displayed, the selected delay time

will flash and the START/PAUSE button will remain lit in a

fixed manner.

3. When the set time has elapsed, a long beep sounds,

the DELAYED START indicator light switches off and the

wash cycle begins.

To deselect the DLEAYED START option, press the DELAYED

START button repeatedly until the text OFF appears.

The Delayed Start function cannot be set once a wash

cycle has been started.

Short Time option

This option can be used to reduce the duration of the main wash

cycles while maintaining the same washing and drying perfor-

mance levels.

After selecting the wash cycle, press the Short Time option but-

ton; the illumination of the corresponding indicator light followed

by a short beep indicates its selection.

To deselect the option, press the same button again.

Good Night option

This option reduces the amount of noise made by the machine

and lengthens the wash cycles. It is a useful option because it

enables users to benefit from the night-time energy rate.

After selecting the wash cycle, press the Good Night option

button; the illumination of the corresponding indicator light fol-

lowed by a short beep indicates its selection.

To deselect the option, press the same button again.

Multi-functional tablets

This option optimises washing and drying results.

When using multi-functional tablets, press the MULTI-

FUNCTIONAL TABLETS button; the corresponding indicator

light will illuminate. If the button is pressed again the option will

be deselected.

The Multi-functional tablets option results in the

lengthening of the wash cycle.

The MULTI-FUNCTIONAL TABLETS option remains set

for subsequent wash cycles if it is not deselected.

The use of tablets is only recommended when the

MULTI-FUNCTIONAL TABLETS option is available.

This option is not recommended for use with wash cycles

which do not specify the use of multi-functional tablets

(see Table of options).

The Short Time and Good Night options are not

compatible with each other.

The Short Time and Good Night options are not

compatible with the HALF LOAD option.

Extra drying

To improve the dryness level of the crockery, press the

EXTRA DRYING button; the indicator light will illuminate. If it is

pressed again the option will be deselected.

The EXTRA DRYING option increases the duration of

the wash cycle.

SELFCARE WASH CYCLE

This disinfecting wash cycle deep cleans the inside of the

dishwasher, thereby reducing the formation of bad odours.

WARNING

The SELFCARE wash cycle should be performed as part of

your dishwasher maintenance routine, using special single-

dose products (follow the instructions on the packaging)

while the dishwasher is EMPTY.

A B C D E F

Table of

options

Delayed

Start

Half

Load

Tabs

Extra

Dry

Short

Time

Good

Night

Auto Super wash

Yes

Normal

Yes

Daily A 60’

Yes

Soaking

Yes

Eco 50°C

Yes

Speed 25’

Yes

Crystals

Yes

Auto Duo Wash

Yes

Ultra Intensive

Yes

Special Guest

Yes

Baby Cycle

Yes

Self Care

Yes

- The machine will switch off automatically

during certain periods of inactivity, in order to

minimise electricity consumption.

Wash cycles

For available OPTIONS please refer to the Table of options on the Start-up and use page.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Notes:

Optimum performance levels when using the "Daily A 60 and "Speed 25  cycles can be achieved by observing the maximum amounts

of crockery specified.

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5 ml of liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less energy

and is les harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following

address: [email protected]

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle selection instructions Wash cycle

Powder Liquid Tablets

Wash

cycles

which

include

drying

Options

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Heavily soiled dishes and pans (not to be

used for delicate items).

Auto

Super Wash

35 g (A)

35 ml (A)

1 (A)

Yes

A-B-C-D-E

2:25’

Normally soiled pans and dishes. Standard

daily wash cycle.

Normal

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A-B-C-D-

E-F

1:50’

Limited quantity of daily soiling. (4 place

settings + 1 saucepan +1 frying pan).

Daily A 60’

25 g (A)

25 ml (A)

1 (A)

A-B-C

1:00’

Pre-wash for dishes while awaiting

completion of the load with the dishes from

the next meal.

Soaking

A – B

0:08’

Environmentally-friendly wash cycle with low

energy consumption levels, suitable for pans

and dishes.

Eco

* 50° C

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A–B-C-D-F

2:55’

Economic and fast wash to be used for lightly

soiled dishes. (Run cycle immediately after

use) (2 plates + 2 glasses + 4 pieces of

cutlery + 1 saucepan + 1 small frying pan).

Speed 25’

25 g (A)

25 ml (A)

1 (A)

A - C

0:25’

Economic and fast wash for delicate items

which are sensitive to high temperatures.

(Run cycle immediately after use) (glasses,

upper rack + delicate plates, lower rack ).

Crystals

35 g (A)

35 ml (A)

1 (A)

Yes

A–B–C-D

1:30’

Wash spread over the two racks: delicate for

crystal and glasses on the upper rack and

heavy duty for the pans on the lower rack.

Auto

Duo Wash

35 g (A)

35 ml (A)

1 (A)

Yes

A–C–D-E

1:45’

Heavily soiled saucepans or pans with

residual dried-on food.

Ultra

Intensive

35 g (A)

5 g (B)

35 ml (A)

5 ml (B)

1 (A)

1 (bottom

of the

appliance)

Yes

A–B–C-D

2:35'

Rinse and drying cycle for dishes that are

seldom used and are only dusty.

Special

Guest

Yes

A–B – D

0:32’

Disinfecting wash cycle suitable for washing

bottles, rings and teats together with plates,

cups, glasses and cutlery. The crockery

should only be loaded on the upper rack.

Baby Cycle

20 g (A)

20 ml (A)

Yes

1:20'

Disinfecting cycle for cleaning the inside of

the dishwasher, to be carried out only when

the dishwasher is EMPTY using specific

detergents designed for dishwasher

maintenance.

SelfCare

0:40'

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard

or very hard. Follow the instructions given on the

packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 When the LOW RINSE AID* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure it

does not overflow from the

dispenser. If this happens, clean the

spill immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results,

you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster (F) to one of the 6

pre-set positions (the default position is set to 4):

 If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

 If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Switch on the appliance by pressing the ON/OFF button.

- Press the P button and hold for a few seconds; two short

beeps will sound, The text "WATER HARDNESS" will appear

on the display and the set hardness number will also flash

slowly on the display (the water softening system is set by

default to number 3).

- Press the DELAYED START button (levels 1 to 5) or the

HALF LOAD button (levels 5 to 1) repeatedly, until the

desired hardness level has been reached (1-2-3-4-5

*, see

hardness table). You will be able to scroll through a maximum

of 5 levels. Press the P button to confirm.

To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty.

Refined salt removes limescale from the water, thus

avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (see Description) and should be filled:

 When the green float

* cannot be seen by simply looking at

the cap of the salt dispenser.

 When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew

the container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

* (see figure) and

fill the salt container right up to its edge

(this should hold approximately 1 kg); it is not unusual for a

little water to leak out.

4. Remove the funnel* and wipe any salt residue away from

the opening; rinse the cap under running water and then

screw it on, the head facing downwards so as to let the

water flow out of the four cracks which are arranged in a

star shape on the lower part of the cap. (the container cap

with the green float

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no

detergent can get into the container during the wash cycle

(this could damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

Water Hardness Table

°dH °fH mmol/l level

0 6 0 10 0 1 1

6 11 11 20 1.1 2 2

12 17 21 30 2.1 3 3

17 34 31 60 3.1 6 4

34 50 61 90 6.1 9

For values between 0°f and 10°f, we do not

recommend the use of salt.

* this setting may cause a slight increase in the

duration of the cycle.

Care and maintenance

Shutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle to avoid

leaks.

 Always unplug the appliance when cleaning it and

when performing maintenance work.

Cleaning the dishwasher

 The external surfaces of the machine and the control

panel may be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

 Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a

little vinegar.

Preventing unpleasant odours

 Always keep the door of the appliance ajar in order to

avoid moisture from forming and being trapped inside

the machine.

 Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This will

avoid food becoming trapped in the seals, which is

the main cause behind the formation of unpleasant

odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer

arms and block the holes used to spray the water. It is

therefore recommended that the arms are checked from

time to time and cleaned with a small non-metallic

brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in

an anti-clockwise direction.

The upper sprayer arm should

be replaced with the holes

facing upwards.

The lower sprayer arm can be

removed by pressing on the

side tabs and pulling it

upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it

is clear and free of impurities before performing the

necessary connections. If this precaution is not taken,

the water inlet could become blocked and damage the

dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter

and clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the

water. They should be cleaned if you wish to achieve the

best results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if the

filter is loose.

 After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using a

non-metallic brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2. Remove the cup filter B by exerting a slight pressure on

the side flaps (fig. 2).

3. Slide out the stainless steel plate filter A (fig. 3).

4. Inspect the trap and remove any food residue.

NEVER REMOVE the wash cycle pump (black detail)

(fig. 4).

After cleaning the filters, replace the filter assembly and fix it

in position correctly; this is essential for maintaining the

efficient operation of the dishwasher.

Leaving the machine unused for extended

periods

 Disconnect the appliance from the electricity supply and

shut off the water tap.

 Leave the door of the appliance ajar.

 When you return, run a wash cycle when the dishwasher is

empty.

* Only available in selected models.

Precautions, advice

and Assistance

This appliance was designed and manufactured in

compliance with current international safety standards. The

following information has been provided for safety reasons

and should therefore be read carefully.

General safety

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

 Children should be supervised to ensure that they do not

play with the appliance.

 The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

 The appliance must be used by adults only, to wash

domestic crockery in accordance with the instructions in

this manual.

 The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

machine exposed to rain and storms.

 Do not touch the appliance when barefoot.

 When unplugging the appliance always pull the plug from

the mains socket, do not pull on the cable.

 The water supply tap must be shut off and the plug should

be removed from the electrical socket before cleaning the

appliance or carrying out any maintenance work.

 If the appliance breaks down, do not under any

circumstances touch the internal parts in an attempt to

perform the repair work yourself.

 Never touch the heating element.

 Do not lean or sit on the open door of the appliance: this

may cause the appliance to overturn.

 The door should not be left open as it may create a

dangerous obstacle.

 Keep detergent and rinse aid out of reach of children.

 The packaging material should not be used as a toy.

Disposal

 Disposal of packaging materials: observe local legislation

so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using the

normal solid urban waste cycle. Exhausted appliances

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

For further information relating to the correct disposal of

household appliances, owners may contact the relevant

public authority or the local appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

 Only begin a wash cycle when the dishwasher is full. While

waiting for the dishwasher to be filled, prevent unpleasant

odours using the Soak cycle (see Wash cycles).

 Select a wash cycle which is suited to the type of crockery

and to the soil level of the crockery using the Table of wash

cycles:

- For dishes with a normal soil level, use the Eco wash

cycle, which guarantees low energy and water

consumption levels.

- If the load is smaller than usual activate the Half load

option

* (see Start-up and use).

 If your electricity supply contract gives details of electricity

saving time bands, run wash cycles during the periods

when a lower tariff is applied. The Delayed start

* button

(see Start-up and use) helps you organise the wash cycles

accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

 We strongly recommend that you use detergents that do

not contain phosphates or chlorine, as these products are

harmful to the environment.

 Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result detergents

containing enzymes can be used in conjunction with low-

temperature wash cycles in order to achieve the same

results as a normal 65°C wash cycle.

 To avoid wasting detergent, use the product in appropriate

quantities based on the manufacturers recommendations,

the hardness of the water and the soil level and quantity of

crockery to be washed. Even if they are biodegradable,

detergents contain substances which may alter the balance

of nature.

Assistance

Before contacting Assistance:

 Check whether the problem can be resolved using the

Troubleshooting guide (see Troubleshooting).

 Restart the programme to check whether the problem has

ceased to exist.

 If the problem persists, contact the Authorised Technical

Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

 The type of malfunction.

 The appliance model (Mod.).

 The serial number (S/N).

This information can be found on the appliance data plate

(see Description of the appliance).

* Only available in selected models.

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

Problem: Possible causes / Solutions:

The dishwasher does not start or

cannot be controlled

• Switch off the appliance by pressing the ON/OFF button, switch it back on after

approximately one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close • The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to the

hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying program has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and

salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean. • The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take any

water in - Tap shut-off alarm

(the ON/OFF indicator light flashes and

the following message appears on the

display: No water. Open tap. After a

few seconds, A:6 will appear).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when the

beeps sounded.

Switch off the appliance using the ON/OFF button, turn on the tap and switch

the appliance back on after 20 seconds by pressing the same button. Re-

program the appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet

filter blocked

(the ON/OFF indicator light flashes and

the display shows A:7).

• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap

to eliminate the risk of flooding and remove the plug from the electrical socket.

Make sure the water inlet filter has not become blocked by impurities (see “Care

and maintenance” chapter).

Mode demploi

Sommaire

Installation, 14-15

Mise en place et mise à niveau

Raccordements eau et électricité

Conseils pour le premier lavage

Caractéristiques techniques

Description de lappareil, 16

Vue densemble

Tableau de bord

Charger les paniers, 17

Panier inférieur

Panier à couverts

Panier supérieur

Mise en marche et utilisation,18-19

Mettre en marche le lave-vaisselle

Charger le produit de lavage

Options de lavage

Programmes, 20

Tableau des programmes

Produit de rinçage et sel régénérant, 21

Charger le produit de rinçage

Charger le sel régénérant

Entretien et soin, 22

Coupure de larrivée deau et de courant

Nettoyer le lave-vaisselle

Eviter les mauvaises odeurs

Nettoyer les bras de lavage

Nettoyage du filtre dentrée deau

Nettoyer les filtres

En cas dabsence pendant de longues périodes

Précautions conseils et Service, 23

Sécurité générale

Mise au rebut

Economies et respect de lenvironnement

Service

Anomalies et remèdes, 24

Français, 13

LDF 12314E

LAVE-VAISSELLE

Installation

Conserver ce mode demploi pour pouvoir le consulter à

tout moment. En cas de vente, de cession ou de

déménagement, sassurer quil accompagne bien lappareil.

Lire attentivement les instructions: elles contiennent des

conseils importants sur linstallation, lutilisation

et la sécurité de lappareil.

En cas de déménagement, transporter lappareil

verticalement; si besoin est, lincliner sur le dos.

Cet appareil est conçu pour un usage domestique ou

autres applications similaires, telles que:

- lieux aménagés en espace cuisine pour le personnel de

magasins, bureaux et autres lieux de travail;

- fermes;

- utilisation par les clients d'hôtels, de motels ou autres locaux

de type résidentiel;

- chambres d'hôtes.

Mise en place et mise à niveau

1. Déballer lappareil et sassurer quil na pas été endommagé

pendant le transport.

Sil est abîmé, ne pas le raccorder et contacter le revendeur.

2. Installer le lave-vaisselle de manière à ce que les côtés et la

paroi arrière touchent aux meubles adjacents ou au mur.

Lappareil peut être encastré sous un plan de travail continu

(voir feuille de Montage).

3. Installer le lave-vaisselle sur un sol plat et rigide.

Compenser les irrégularités en vissant ou en dévissant les

pieds avant jusquà ce que lhorizontalité de lappareil soit

parfaite. Une bonne horizontalité garantit la stabilité de

lappareil et supprime tout risque de vibrations, bruits et

déplacements.

*. Pour régler la hauteur du pied arrière, agir sur la douille

rouge à six pans située dans la partie avant du lave-vaisselle,

en bas et au milieu, à laide dune clé mâle à six pans,

ouverture 8 mm. Tourner dans le sens des aiguilles dune

montre pour augmenter la hauteur et dans le sens inverse

pour la diminuer. (consulter la notice dinstructions encastré

jointe à la documentation)

Raccordements eau et électricité

Ladaptation des installations électriques et les travaux de

plomberie de linstallation doivent être effectués par du

personnel qualifié.

Le lave-vaisselle ne doit pas écraser les tuyaux ou le

câble dalimentation électrique.

Utiliser des tuyaux neufs pour effectuer le raccordement

de lappareil au réseau de distribution de leau.

Ne pas réutiliser les anciens tuyaux.

Les tuyaux damenée et dévacuation de leau et le câble

dalimentation électrique peuvent être orientés vers la droite ou

vers la gauche pour simplifier linstallation

Raccord du tuyau damenée de leau

 A une prise deau froide: bien visser le tuyau damenée à un

robinet à embout fileté 3/4 gaz; avant de visser, faire couler

leau jusquà ce quelle devienne limpide et dépourvue

dimpuretés qui pourraient engorger lappareil.

 A une prise deau chaude: en cas dinstallation de

chauffage centralisé (radiateurs), le lave-vaisselle peut être

alimenté avec de leau chaude de réseau ne dépassant

pas 60°C.

Visser le tuyau au robinet en procédant comme pour la

prise deau froide.

Si la longueur du tuyau damenée ne suffit pas,

sadresser à un magasin spécialisé ou à un technicien agréé

(voir Assistance).

La pression de leau doit être comprise entre les valeurs

reportées dans le tableau des Caractéristiques techniques (voir

ci-contre).

Faire attention à ce que le tuyau ne soit ni plié ni écrasé.

Raccordement du tuyau d'évacuation de l'eau

raccorder le tuyau d'évacuation, sans le plier, à une

conduite d'évacuation ayant au moins 4 cm de

diamètre.

Le tuyau d'évacuation doit être placé entre 40 et 80 cm

au-dessus du sol ou du plan d'appui du lave-vaisselle

(A).

Avant de raccorder le tuyau d'évacuation de l'eau au

siphon de l'évier, retirer le bouchon en plastique (B).

* Présent uniquement sur certains modèles.

Sécurité anti-fuite

Pour éviter tout risque dinondation, le lave-vaisselle:

- est équipé dun dispositif qui coupe larrivée de leau en cas

danomalie ou de fuite à lintérieur de lappareil.

Quelques modèles sont équipés dun dispositif de sécurité

supplémentaire New Acqua Stop

* qui garantit contre tout

risque dinondation même en cas de rupture du tuyau

damenée de leau.

ATTENTION: TENSION DANGEREUSE!

Il ne faut en aucun cas couper le tuyau damenée de leau car il

contient des parties sous tension.

Raccordement électrique

Avant de brancher la fiche dans la prise de courant, sassurer

que:

 la prise dispose de mise à la terre et est conforme aux

normes;

 la prise est bien apte à supporter la puissance maximale

de lappareil reportée sur la plaque signalétique fixée à la

contre-porte (voir paragraphe Description du lave-

vaisselle);

 la tension dalimentation est bien comprise entre les valeurs

figurant sur la plaque signalétique de la contre-porte;

 la prise est bien compatible avec la fiche de lappareil.

Autrement, faire remplacer la fiche par un technicien agréé

(voir Assistance); nutiliser ni rallonges ni prises multiples.

Après installation de lappareil, le câble dalimentation

électrique et la prise de courant doivent être facilement

accessibles.

Le câble ne doit être ni plié ni trop écrasé.

Afin déviter tout danger, faire changer le cordon dalimen-

tation abîmé, par le fabricant ou par son service après-vente.

(Voir Assistance)

Nous déclinons toute responsabilité en cas de non-

respect des normes énumérées ci-dessus.

Ruban anti-condensation*

Après avoir encastré le lave-vaisselle, ouvrir la porte et coller

le ruban adhésif transparent sous le plan en bois pour le

protéger contre la formation de condensation.

Conseils pour le premier lavage

Une fois linstallation terminée et tout de suite avant le premier

lavage, remplir complètement deau le réservoir à sel et ajouter

environ 1 kg de sel (voir Produit de rinçage et sel régénérant)

: il est tout à fait normal que de leau déborde. Sélectionner le

degré de dureté de leau (voir Produit de rinçage et sel

régénérant). - Après remplissage du réservoir à sel, le voyant

SEL

* s'éteint.

Le manque de remplissage du réservoir à sel, peut

endommager l'adoucisseur d'eau et l'élément chauffant.

* Présent uniquement sur certains modèles.

Caractéristiques techniques

Dimensions

largeur 60 cm

hauteur 85 cm

profondeur 60 cm

Capacité 14 couverts standard

Pression eau

d’alimentation

0,05 ÷ 1 MPa (0,5 ÷ 10 bar)

7,25 – 145 psi

Tension

d’alimentation

Voir étiquette des caractéristiques

Puissance totale

absorbée

Voir étiquette des caractéristiques

Fusible Voir étiquette des caractéristiques

Cet appareil est conforme aux

Directives Communautaires

suivantes:

- 2006/95/EC (Basse Tension)

- 2004/108/EC (Compatibilité

Electromagnétique)

-2005/32/EC (Comm. Reg.

1275/2008) (Ecodesign)

-97/17/EC (Etiquetage)

-2002/96/EC (DEEE)

Vue densemble

Description de

lappareil

1. Panier supérieur

2. Bras de lavage supérieur

3. Clayettes rabattables

4. Réglage hauteur du panier

5. Panier inférieur

6. Bras de lavage inférieur

7. Panier à couverts

8. Filtre lavage

9. Réservoir à sel

10. Bacs produit de lavage et réservoir à

produit de rinçage

11. Plaque signalétique

12. Tableau de bord

***

*** Uniquement pour modèles tout intégrables.

* Présent uniquement sur certains modèles.

Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.

Tableau de bord

Touche Sélection de programme

Touche Pastilles

multifonction

Touche

Départ différé

Voyant

Demi-charge Supérieur/inférieur

Voyant ON-OFF

Voyant

Manque de sel

Voyant Manque de

produit de rinçage

Touche option

GoodNight

Touche et voyant

Marche/Arret

Indicateur lumineux du temps restant

Touche

ON-OFF/RESET

Touche

Demi-charge

Voyant pastilles

multifonction

Voyant

Départ différé

Voyant option GoodNight

Touche

Séchage Super

Voyant Séchage Super

Touche option

Short Time

Voyant option Short Time

Indicateur lumineux du

nom du programme

Charger les paniers

Avant de charger les paniers, débarrasser la vaisselle des

déchets plus importants et vider les verres et les coupes.

Après avoir chargé le lave-vaisselle, sassurer que les bras

de lavage tournent librement.

Panier du bas

Le panier du bas peut contenir des casseroles, des

couvercles, des assiettes, des saladiers, des couverts

etc.selon les Exemples de chargement.

Ranger de préférence sur les côtés du panier les plats de

service et les grands couvercles sans toutefois bloquer la

rotation du bras de lavage supérieur.

Certains modèles de

lave-vaisselle sont

pourvus de secteurs

rabattables

* qui

peuvent être placés

à la verticale pour ranger des assiettes ou à lhorizontale pour

ranger des casseroles et des saladiers.

Panier à couverts

Le panier à couverts peut varier selon le modèle de lave-

vaisselle : séparable, non séparable, coulissant. Le panier à

couverts non séparable doit être placé obligatoirement dans

la partie avant du panier inférieur.

Le panier séparable

se détache en deux

parties, solution

pratique en cas de

lavage d'une demi-

charge (si cette

option est prévue pour le modèle de lave-vaisselle), il peut

coulisser parmi les accessoires fixes ou rabattables pour aller

se placer dans n'importe quel coin du panier du bas.

- Ils sont équipés tous deux de rabats coulissants qui

permettent de mieux ranger les couverts.

Ranger les couteaux et les ustensiles de cuisine pointus et

coupants dans le panier à couverts, pointes tournées vers le

bas, ou, à plat, sur les clayettes rabattables du panier

supérieur.

Exemples de rangement dans le panier à couverts

Panier du haut

Y ranger la vaisselle fragile et légère : verres, tasses à thé et à

café, soucoupes, saladiers bas, casseroles basses peu sales,

en suivant les Exemples de chargement.

 Tasses et tasses à café, couteaux longs et pointus, couverts

de service: les placer sur les étagères rabattables

**.

Etagères rabattables à inclinaison variable*

- L'inclinaison permet de gagner de la place dans le panier

supérieur, de ranger des verres à pied de longueur différente

et d'améliorer les performances de séchage.

- Soulever l'étagère rabattable, la faire glisser légèrement et la

placer selon l'inclinaison désirée.

Régler la hauteur du panier supérieur

Pour optimiser le rangement de la vaisselle, possibilité de régler le

panier supérieur en position haute ou basse:

(pour les modèles équipés de cycle Baby, placer le panier

supérieur en position basse pour procéder à des chargements

Baby).

Régler de préférence la hauteur du panier quand ce

dernier est VIDE.

Ne jamais soulever ou abaisser le panier dun seul côté.

Ouvrir les butées des glissières du

panier à droite et à gauche et sortir le

panier. Positionner le panier en position

haute ou basse, le faire glisser le long

des glissières jusquà ce que les roues

avant entrent elles aussi et refermer les

butées (voir figure).

Si le panier est équipé de poignées

Espace double

* (voir figure), sortir le

panier du haut en fin de corse, saisir les

poignées sur les côtés du panier et

déplacer vers le haut ou vers le bas;

laisser retomber le panier sans le lâcher.

Exemples de chargement du panier supérieur/

inférieur

Etagères rabattables Baby

Les modèles de lave-vaisselle avec Cycle

Baby sont fournis équipés détagères

rabattables spéciales pour le lavage de

biberons, bagues et tétines. (voir feuille

d'instructions jointe à la documentation)

Vaisselle nallant pas au lave-vaisselle

 Objets en bois, avec des manches en bois ou en corne ou

ayant des parties collées.

 Objets en aluminium, cuivre, laiton ou étain.

 Vaisselle en plastique thermorésistant.

 Porcelaines anciennes ou peintes à la main.

 Argenterie ancienne. Les pièces dargenterie non ancienne

peuvent par contre être lavées avec un programme délicat

après sêtre assuré quelles ne touchent pas à dautres métaux.

Nous conseillons dutiliser de la vaisselle lavable au lave-

vaisselle.

* Présent uniquement sur certains modèles.

** Leur nombre et leur position varient.

Inclinaison A Inclinaison B Inclinaison C

Mise en marche et

utilisation

Charger le produit de lavage

Un bon résultat de lavage dépend aussi dun bon dosage

du produit de lavage. Un excès de produit de lavage ne

lave pas mieux et pollue lenvironnement.

Nutiliser que du produit de lavage spécial lave-

vaisselle.

NE PAS UTILISER de produits pour laver la vaisselle à

la main.

Une utilisation excessive de produit de lavage peut

laisser des résidus de mousse en fin de cycle.

L'utilisation de pastilles n'est conseillée que pour les

modèles qui prévoient l'option PASTILLES

MULTIFONCTION.

Pour obtenir des performances de lavage et de

séchage optimales, utiliser des produits de lavage en

poudre, du liquide de rinçage et du sel.

bac A: Produit de lavage

bac B: Produit de prélavage

1. Appuyer sur la touche D pour

ouvrir le couvercle C.

2. Pour doser le produit de lavage se

reporter au Tableau des

programmes:

 en poudre : bacs A et B.

 pastilles: si le programme en

prévoit 1, placer cette dernière dans

le bac A et fermer le couvercle; sil en

prévoit 2, mettre la deuxième dans le fond de la cuve.

3. Eliminer les résidus de produit de lavage sur les bords du

bac et fermer le couvercle jusquau déclic.

* Présent uniquement sur certains modèles.

Première mise en service

Choisir la langue

Appuyer sur ON/OFF, un bip bref retentit et la langue sélectionnée

saffiche.

Faire défiler la liste des langues, à laide de la touche DÉPART

DIFFÉRÉ pour avancer et celle de DEMI-CHARGE pour revenir

en arrière, jusquà la langue voulue. Appuyer sur la touche P

pour confirmer et entrer automatiquement dans la liste des

programmes de lavage.

A chaque allumage qui suit la première mise en service, le lave-

vaisselle affiche la liste des programmes.

Pour modifier le choix de la langue après la première mise en

service, il suffit dappuyer simultanément pendant quelques

secondes sur la touche P et sur la touche de DÉPART DIFFÉRÉ.

Mettre en marche le lave-vaisselle

1. Ouvrir larrivée deau.

2. Appuyer sur la touche ON-OFF : un bip court retentit, le

voyant ON/OFF et lafficheur sallument.

3. Ouvrir la porte et doser le produit de lavage (voir plus bas).

4. Charger les paniers (voir Charger les paniers) et fermer la

porte.

5. Pour sélectionner le programme selon le type de vaisselle et

son degré de salissure (voir tableau des programmes)

appuyer sur la touche P.

6. Sélectionner les options de lavage (voir ci-contre).

7. Appuyer sur la touche Marche pour faire démarrer le lavage :

un bip prolongé signale le démarrage du programme et le nom

du programme sélectionné ainsi que le temps de lavage restant

saffichent.

8. A la fin, deux bips courts et un bip prolongé annoncent la fin

du programme et le message FIN DE CYCLE saffiche à lécran.

Eteindre lappareil par pression sur la touche ON-OFF, fermer

le robinet de leau et débrancher la fiche de la prise de courant.

9. Attendre quelques minutes avant de sortir la vaisselle pour

éviter de se brûler. Décharger les paniers en commençant par

celui du bas.

PROGRAMMES AUTO

*: grâce à un capteur spécial, ce

modèle de lave-vaisselle peut évaluer le degré de salissure et

sélectionner le lavage le plus efficace et le plus économique.

La durée des programmes automatiques peut varier du fait de

lintervention du capteur.

En cas de vaisselle peu sale ou précédemment rincée à

leau, réduire considérablement la quantité de produit de

lavage.

Modifier un programme en cours

En cas derreur de sélection dun programme, il est possible de

le modifier, à condition quil vienne tout juste de démarrer : pour

changer un cycle de lavage en cours, éteindre puis rallumer

lappareil par une pression prolongée sur la touche ON/OFF,

sélectionner ensuite le nouveau programme et les options

désirées.

Introduire de la vaisselle en cours de lavage

Appuyer sur la touche Marche/Pause, (la touche se met à

clignoter). Ouvrir la porte en faisant attention à la vapeur

chaude qui séchappe et introduire la vaisselle. Appuyer sur la

touche Marche/Pause (lumière fixe): le cycle repart après un

bip prolongé.

Appuyer sur la touche Marche/Pause pour mettre lappareil

en pause, le programme et le départ différé éventuellement

sélectionné sont stoppés.

Pendant cette phase, aucun changement de programme nest

possible.

Interruptions accidentelles

En cas douverture de la porte en cours de lavage ou de

coupure de courant, le programme sarrête. Il redémarre du

point où il a été interrompu dès que le courant revient ou que la

porte est refermée.

Options de lavage*

La sélection, la modification ou lannulation des OPTIONS nest

possible quaprès avoir choisi le programme de lavage et

avant dappuyer sur la touche Marche/Pause.

Seules les options compatibles avec le programme choisi peuvent

être sélectionnées. Si une option nest pas compatible avec le

programme sélectionné, (voir tableau programmes) la led

correspondante clignote 3 fois de suite et 2 bips courts

retentissent.

En cas de sélection dune option incompatible avec une option

précédemment sélectionnée, celle-ci clignote 3 fois de suite, 3

bips retentissent puis elle séteint, tandis que la dernière sélection

effectuée reste allumée.

Pour désactiver une option sélectionnée par erreur, appuyer à

nouveau sur la touche correspondante.

* Présent uniquement sur certains modèles.

Pastilles Multifonction

Cette option permet doptimiser le résultat de lavage et de

séchage.

En cas dutilisation de pastilles multifonction, appuyer sur la

touche PASTILLLES MULTIFONCTION qui sallume. Pour

désactiver cette option appuyer à nouveau sur la touche.

Loption Pastilles Multifonction prolonge la durée du

programme.

Loption pastilles multifonction reste mémorisée lors

des allumages suivants de lappareil à moins quelle nait

été désactivée.

Lutilisation de pastilles nest conseillée quen

présence de loption PASTILLES MULTIFONCTION.

Cette option est déconseillée pour les programmes qui

ne prévoient pas lutilisation de pastilles multifonction

(voir tableau des options).

Option Short Time

Cette option permet de réduire la durée des principaux

programmes tout en assurant les mêmes performances de

lavage et de séchage

Après avoir sélectionné le programme, appuyer sur la

touche Option Short Time, lallumage du voyant et un bip

court annoncent que la sélection a eu lieu.

Pour désactiver cette option, appuyer à nouveau sur la

même touche.

Les Options Short Time et Good Night ne sont

pas compatibles entre elles.

Les Options Short Time et Good Night ne sont

pas compatibles avec loption DEMI-CHARGE.

Option Good Night

Cette option permet un fonctionnement encore plus silencieux

en prolongeant la durée des programmes, idéale car elle permet

de profiter du tarif électricité nocturne.

Après avoir sélectionné le programme, appuyer sur la touche

Option Good Night, lallumage du voyant et un bip court

annoncent que la sélection a eu lieu.

Pour désactiver cette option, appuyer à nouveau sur la même

touche.

Séchage super

Pour améliorer le séchage de la vaisselle, appuyer sur la touche

SÉCHAGE SUPER qui sallume. Pour désactiver loption

appuyer une nouvelle fois.

Loption SÉCHAGE SUPER prolonge la durée du

programme.

PROGRAMME AUTO-NETTOYAGE

Ce programme de lavage spécial pour lhygiène intérieure du

lave-vaisselle permet de le laver à fond et de réduire ainsi la

formation de mauvaises odeurs.

Demi-charge panier supérieur ou inférieur

Le programme demi-charge permet de laver une petite

vaisselle et de faire des économies deau, délectricité et de

produit de lavage. Sélectionner le programme, appuyer sur la

touche DEMI-CHARGE: le triangle correspondant à la charge

choisie sallume et le lavage nest lancé que dans le panier

supérieur ou que dans le panier inférieur. Pour désactiver

cette option appuyer à nouveau sur la touche.

La demi-charge nest pas compatible avec lOption Good

Night et avec lOption Short Time.

Penser à ne ranger la vaisselle que dans le panier

supérieur ou inférieur et à réduire de moitié la quantité de

produit de lavage.

Mieux vaut utiliser un produit de lavage en poudre.

Cette option nest pas utilisable avec le programme:

Rapide.

Départ différé

Possibilité de différer le départ du programme de 1 à 24 heures:

1. après avoir sélectionné le programme de lavage et toute autre

option possible, appuyer sur la touche DÉPART DIFFÉRÉ: le

symbole du Départ différé se mettra à clignoter. Sélectionner à

laide de la même touche à quel moment on veut faire démarrer

le cycle de lavage (de 1 à 24 heures).

2. Confirmer son choix à laide de la touche MARCHE/PAUSE, le

symbole cesse de clignoter, le compte à rebours commence et le

message Démarrage...saffiche, le retard sélectionné clignote et

la touche MARCHE/PAUSE cesse de flasher (lumière fixe).

3. A lexpiration du délai dattente, un bip prolongé retentit, le

voyant du DÉPART DIFFÉRÉ séteint et le programme démarre.

Pour désactiver un DÉPART DIFFÉRÉ, appuyer sur la touche

DÉPART DIFFÉRÉ jusquà affichage de OFF.

Aucune sélection de Départ différé nest plus possible

en cours de cycle.

ATTENTION

Le programme de lavage AUTO-NETTOYAGE doit être

effectué à vide et avec des produits dentretien

spéciaux lave-vaisselle monodose (se conformer aux

instructions reportées sur lemballage).

A B C D E F

Tableau des

options

Départ

différé

Demi-

charge

Pastilles

Multifonction

Séchage

Super

Short

Time

Good

Night

Super lavage

Oui

Non

Normal

Oui

Quotidien A 60’

Oui

Non

Trempage

Oui

Non

Eco 50°C

Oui

Non

Oui

Rapide 25’

Oui

Non

Oui

Non

Cristal

Oui

Non

Duo Wash

Oui

Non

Oui

Non

Intensive

Oui

Non

Special Invité

Oui

Non

Oui

Non

Cycle Bébé

Oui

Non

Auto-Nettoyage

Oui

Non

- Pour réduire sa consommation d'énergie, la

machine s'éteint automatiquement dans certaines

conditions de non-utilisation.

Programmes

En cas de vaisselle peu sale ou précédemment rincée à leau, réduire considérablement la quantité de produit de lavage.

Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.

Remarques:

Pour obtenir des performances optimales avec les programmes "Quotidien et Rapide 25" il est conseillé de respecter le nombre de

couverts indiqué.

* Le programme Eco est conforme à la norme EN-50242. Il a une durée de lavage plus longue que les autres programmes mais

cest aussi celui qui consomme le moins dénergie et qui respecte le plus lenvironnement.

Note pour les laboratoires d'essai: pour toutes informations détaillées sur les conditions d'essai comparatif EN, s'adresser à :

[email protected]

Pour simplifier le dosage du produit de lavage, prendre note que:

1 cuillère à soupe = 15 gr. de poudre = 15 ml de liquide environ - 1 cuillère à café = 5 gr. de poudre = 5 ml de liquide environ

Produit de lavage

(A) = bac A

(B) = bac B

Indications sur le choix des

programmes

Programme

Poudre Liquide Pastilles

Programmes

prévoyant le

séchage

Options

Durée du

programme

(tolérance

±10% Hrs. Min

Vaisselle et casseroles très sales

(déconseillé pour la vaisselle

fragile).

Super

Lavage

35 g (A)

35 ml (A)

1 (A)

Oui

A-B-C-D-

2:25’

Vaisselle et casseroles

normalement sales. Programme

standard quotidien.

Normal

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A) Oui

A-B-C-D-

E-F

1:50’

Vaisselle du jour en quantité

réduite. (4 couverts + 1 casserole +

1 poêle).

Quotidien 60’

25 g (A)

25 ml (A)

1 (A)

Non

A-B-C

1:00’

Lavage préalable dans l’attente de

compléter le chargement au repas

suivant.

Trempage

Non

A - B 0:08’

Lavage écologique à faible

consommation d’électricité pour

vaisselle et casseroles.

Eco

* 50°C

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Oui

A-B-C-D-

2:55’

Cycle économique et rapide pour

vaisselle peu sale, tout de suite

après l’usage. (2 assiettes +2

verres +4 couverts +1 casserole +

1 petite poêle)

Rapide 25’

25 g (A)

25 ml (A)

1 (A)

Non

A - C

0:25’

Cycle économique et rapide pour

vaisselle fragile ne supportant pas

les hautes températures, tout de

suite après l’usage. (verres à pied

panier supérieur + assiettes fragiles

panier inférieur).

Cristal

35 g (A)

35 ml (A)

1 (A)

Oui

A-B-C-D

1:30’

Lavage différencié dans les deux

paniers : délicat dans celui du haut

pour verres et cristal, énergique

dans celui du bas pour les

casseroles.

Duo Wash

35 g (A)

35 ml (A)

1 (A)

Oui

A-C-D-E

1:45’

Casseroles extrêmement sales ou

avec incrustations d’aliments.

Ultra Intensif

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

1 (fond de

cuve)

Oui

A-B-C-D

2:35’

Cycle de rinçage et de séchage

pour vaisselle peu utilisée; à

dépoussiérer seulement.

Special Invité

Non

Oui

A-B-D

0:32’

Cycle de lavage pour l’hygiène des

biberons, bagues, tétines, lavés en

même temps qu’assiettes, tasses,

verres et couverts. Charger

uniquement le panier du haut.

Cycle Bébé

20 g (A)

20 ml (A)

Non

Oui

1:20’

Cycle de lavage spécial pour

l’hygiène intérieure du lave-

vaisselle à utiliser à VIDE avec

des produits d’entretien

spéciaux lave-vaisselle.

Auto

Nettoyage

Non

0:40’

Leht laaditakse ...

Hotpoint LDF 12314E Omaniku manuaal

Kaubamärk: Hotpoint

Mudel: LDF 12314E

Kategooria: Nõudepesumasinad

Tüüp: Omaniku manuaal

See juhend sobib ka

Laadige alla PDF

aruanne

teistes keeltes

Deutsch: Hotpoint LDF 12314E Bedienungsanleitung
español: Hotpoint LDF 12314E El manual del propietario
português: Hotpoint LDF 12314E Manual do proprietário
français: Hotpoint LDF 12314E Le manuel du propriétaire
English: Hotpoint LDF 12314E Owner's manual
dansk: Hotpoint LDF 12314E Brugervejledning
Nederlands: Hotpoint LDF 12314E de handleiding

Hotpoint LDF 12314E Omaniku manuaal

See juhend sobib ka

Hotpoint LDF 12314E Omaniku manuaal

teistes keeltes

Muud dokumendid