LG 40UF671V Kasutusjuhend

Kategooria
LCD-telerid
Tüüp
Kasutusjuhend
Please read this manual carefully before operating your
set and retain it for future reference.
Safety and Reference
OWNER’S MANUAL
www.lg.com
*MFL68702415*
P/NO : MFL68702415(1502-REV01)
Printed in Korea
ENGLISH
Please read these safety precautions carefully before
using the product.
environments:
t A location exposed to direct sunlight
t An area with high humidity such as a bathroom
t Near any heat source such as stoves and other devices that
produce heat
t Near kitchen counters or humidiers where they can easily be
exposed to steam or oil
t An area exposed to rain or wind
t Near containers of water such as vases
Otherwise, this may result in re, electric shock, malfunction or product
deformation.
cause a re hazard.
TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
pin is wet or covered with dust, dry the power plug completely or wipe
dust o. You may be electrocuted due to excess moisture.
e sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
t power cable plug completely into wall socket otherwise if not
secured completely into socket, re ignition may break out.
such as a heater. This may cause a re or an electric shock hazard.
Otherwise, this may result in re or electric shock.
rain from owing in. This may cause water damaged inside the Product
and could give an electric shock.
cabling from rear of TV as to not create possibility of electric shock /
re hazard.
outlet. Otherwise, this may result in re due to over-heating.
ENGLISH
devices. Otherwise, this may result in injury or damage to the product.
Desiccant
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suocation. Keep it out
of the reach of children.
Otherwise, the TV may fall over, which may cause serious injury.
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
danger of combustion/explosion or re due to careless handling of the
inammable substances.
into the product, or inammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, re or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
substance (thinner or benzene). Fire or electric shock accident can
occur.
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
You may be electrocuted.
windows and ventilate. It may cause a re or a burn by a spark.
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
ENGLISH
y of the following occur, unplug the product immediately and
contact your local service centre.
t The product has been impacted by shock
t The product has been damaged
t Foreign objects have entered the product
t The product produced smoke or a strange smell
This may result in re or electric shock.
TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric leakage/shock/re.
lled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
ater enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately . Otherwise ,this may result in electric shock or re.
LG Electronics. Otherwise, this may result in re, electric shock,
malfunction or product deformation.
or electric shock.
oduct where no radio wave occurs.
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
ip over, which may cause injury or damage to the product.
ou install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), x
it carefully so as not to drop.
Only use the attachments / accessories specied by the manufacturer.
technician. If not installed by a qualied technician, this may create a
re hazard or an electric shock hazard.
ENGLISH
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
remote control.
batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open replace and electric heaters .
Do not place non-rechargeable batteries in charging device.
e sure there are no objects between the remote control and its
sensor.
lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting
or darken viewing area.
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
ollow the installation instructions below to prevent the product
from overheating.
t The distance between the product and the wall should be more
than 10cm.
t Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
t Do not install the product on a carpet or cushion.
t Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in re.
for long periods as the ventilation openings may become hot. This does
not aect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
a re hazard.
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
ENGLISH
as nail, pencil or pen, or make a scratch on it, as it may causedamage
to screen.
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
rst and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn o this unit
by SWITCH.
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a re
hazard or cause electric shock.
product is heavy. Otherwise, this may result in injury.
product.
Accumulated dust can cause mechanical failure.
er all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
oduct feels cold to the touch, there may be a small “icker”
when it is turned on. This is normal, there is nothing wrong with
product.
million to six million pixels. You may see tiny black dots and/or brightly
coloured dots (red, blue or green) at a size of 1ppm on the panel. This
does not indicate a malfunction and does not aect the performance
and reliability of the product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
ENGLISH
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
* LG LED TVs are LCD TVs with LED backlighting.
menu, scene from a video game) for a prolonged time may cause
damage to the screen, resulting in retention of the image, which is
known as image sticking. The warranty does not cover the product for
image sticking.
Avoid displaying a xed image on your television’s screen for a
prolonged period (2 or more hours for LCD, 1 or more hours for Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking
may occur on the borders of the panel.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
Generated Sound
“Cracking noise: A cracking noise that occurs when watching or turning
o the TV is generated by plastic thermal contraction due to tempera-
ture and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not aect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
Viewing 3D imaging (Only 3D
models)
Viewing Environment
t Viewing Time
- When watching 3D contents, take 5 to 15 minute breaks every
hour. Viewing 3D contents for a long period of time may cause
headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
t Some users may experience a seizure or other abnormal symptoms
when they are exposed to a ashing light or particular pattern
from 3D contents.
t Do not watch 3D videos if you feel nausea, are pregnant and/ or
have a chronic illness such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
t 3D Contents are not recommended to those who suer from stereo
blindness or stereo anomaly. Double images or discomfort in
viewing may be experienced.
t If you have strabismus (cross-eyed), amblyopia (weak eyesight) or
astigmatism, you may have trouble sensing depth and easily feel
fatigue due to double images. It is advised to take frequent breaks
than the average adult.
t If your eyesight varies between your right and left eye, correct your
eyesight prior to watching 3D contents.
Symptoms which require discontinuation or
refraining from watching 3D contents
t Do not watch 3D contents when you feel fatigue from lack of sleep,
overwork or drinking.
t When these symptoms are experienced, stop using/watching 3D
contents and get enough rest until the symptom subsides.
- Consult your doctor when the symptoms persist. Symptoms may
include headache, eyeball pain, dizziness, nausea, palpitation,
blurriness, discomfort, double image, visual inconvenience or
fatigue.
ENGLISH
Viewing Environment
t Viewing Distance
- Maintain a distance of at least twice the screen diagonal length
when watching 3D contents. If you feel discomfort in viewing 3D
contents, move further away from the TV.
Viewing Age
t Infants/Children
- Usage/ Viewing 3D contents for children under the age of 6 are
prohibited.
- Children under the age of 10 may overreact and become overly
excited because their vision is in development (for example:
trying to touch the screen or trying to jump into it. Special
monitoring and extra attention is required for children watching
3D contents.
- Children have greater binocular disparity of 3D presentations
than adults because the distance between the eyes is
shorter than that of adults. Therefore they will perceive more
stereoscopic depth compared to adults for the same 3D image.
t Teenagers
- Teenagers under the age of 19 may react with sensitivity due
to stimulation from light in 3D contents. Advise them to refrain
from watching 3D contents for a long time when they are tired.
t Elderly
- The elderly may perceive less 3D eect compared to the young.
Do not sit closer to the TV than the recommended distance.
Cautions when using the 3D glasses
t Make sure to use LG 3D glasses. Otherwise, you may not be able to
view 3D videos properly.
t Do not use 3D glasses instead of your normal glasses, sunglasses or
protective goggles.
t Using modied 3D glasses may cause eye strain or image
distortion.
t Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
t The 3D glasses are fragile and are easily scratched. Always use a
soft, clean piece of cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp objects or clean/wipe them
with chemicals.
Preparing
TE
t Image shown may dier from your TV.
t Your TV’s OSD (On Screen Display) may dier slightly from that
shown in this manual.
t The available menus and options may dier from the input source
or product model that you are using.
t New features may be added to this TV in the future.
t The TV can be placed in standby mode in order to reduce the power
consumption. And the TV should be turned o if it will not be
watched for some time, as this will reduce energy consumption.
t The energy consumed during use can be signicantly reduced if the
level of brightness of the picture is reduced, and this will reduce
the overall running cost.
t The items supplied with your product may vary depending on the
model.
t Product specications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
t For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not t into your TV’s USB port.
A
B
A
B
*A
<
=
*B
<
=
t Use a certied cable with the HDMI logo attached.
t If you do not use a certied HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI Cable Types)
- High-Speed HDMI
®
/
TM
cable (3 m or less)
- High-Speed HDMI
®
/
TM
cable with Ethernet (3 m or less)
t Do not use any unapproved items to ensure the safety and product
life span.
t Any damage or injuries caused by using unapproved items are not
covered by the warranty.
t Some models have a thin lm attached on to the screen and this
must not be removed.
t When attaching the stand to the TV set, place the screen facing
down on a cushioned table or at surface to protect the screen
from scratches.
t Make sure that the screws are fastened completely. (If they are
not fastened securely enough, the TV may tilt forward after being
installed.) Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten correctly.
ENGLISH
Separate purchase
Separate purchase items can be changed or modied for quality
improvement without any notication. Contact your dealer to buy
these items. These devices only work with certain models. The model
name or design may be changed depending on the upgrade of product
functions, manufacturer’s circumstances or policies.
(Depending on model)
AG-F***
Cinema 3D glasses
AG-F***DP
Dual play glasses
LG Audio Device
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the
product lifespan.
t Make sure to turn the power o and disconnect the power cord and
all other cables rst.
t When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent possible
damage from lightning or power surges.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and
soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in
clean water or a diluted mild detergent. Then wipe immediately with
a dry cloth.
t Avoid touching the screen at all times, as this may result in damage
to the screen.
t Do not push, rub, or hit the screen surface with your ngernail or a
sharp object, as this may result in scratches and image distortions.
t Do not use any chemicals as this may damage the product.
t Do not spray liquid onto the surface. If water enters the TV, it may
result in re, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
t It is recommended to move the TV in the box or packing material
that the TV originally came in.
t Before moving or lifting the TV, disconnect the power cord and
all cables.
t When holding the TV, the screen should face away from you to
avoid damage.
Hold the top and bottom of the TV frame rmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
When transporting a large TV, there should be at least 2 people.
t When transporting the TV by hand, hold the TV as shown in the
following illustration.
When transporting the TV, do not expose the TV to jolts or
excessive vibration.
t When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
t Do not apply excessive pressure to cause exing /bending of frame
chassis as it may damage screen.
t When handling the TV, be careful not to damage the protruding
joystick button.
t Avoid touching the screen at all times, as this may result in damage
to the screen.
t Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
ENGLISH
(Image shown may dier from your TV.)
You can simply operate the TV functions, pressing or moving the joystick
button up, down, left or right.
Joystick Button
When the TV is turned o, place your
nger on the joystick button and
press it once and release it.
When the TV is turned on, place your
nger on the joystick button and
press it once for a few seconds and
release it. (However, if the Menu
button is on the screen, pressing and
holding the joystick button will let
you exit the Menu.)
Control
If you place your nger over the
joystick button and move it left or
right, you can adjust the volume level
you want.
Control
If you place your nger over the
joystick button and move it up or
down, you can scrolls through the
saved programmes you want.
Adjusting the Menu
When the TV is turned on, press the joystick button one time. You can
adjust the Menu items moving the joystick button up, down, left or
right.
Turns the power o.
Clears on-screen displays and returns to TV viewing.
TE
t When your nger over the joystick button and push it to the up,
down, left or right, be careful not to press the joystick button. If you
press the joystick button rst, you may not be able to adjust the
volume level and saved programmes.
Mounting on a table
(Depending on model)
1 Lift and tilt the TV into its upright position on a table.
t Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
t Do not place the TV near or on sources of heat, as this may result in
re or other damage.
Using the kensington security
system
(This feature is not available for all models.)
t Image shown may dier from your TV.
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit http://www.
kensington.com. Connect the Kensington security system cable between
the TV and a table.
ENGLISH
Securing the TV to a wall
(This feature is not available for all models.)
Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
t If there are bolts inserted at the eye-bolts position, remove the
bolts rst.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the at surface.
t Make sure that children do not climb on or hang on the TV.
TE
t Use a platform or cabinet that is strong and large enough to
support the TV securely.
t Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the oor. When you attach the TV to other building materials, please
contact qualied personnel. LG recommends that wall mounting be
performed by a qualied professional installer. We recommend the
use of LG’s wall mount bracket. When you do not use LG’s wall mount
bracket, please use a wall mount bracket where the device is adequately
secured to the wall with enough space to allow connectivity to external
devices.
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
Model
32LF55**
32LF62**
32/43LF51**
40/43UF67**
40/43LF57**
43LF54**
49/55UF67**
49LF54**
VESA (A x B) 300 x 300
Standard screw M6
Number of screws 4
Wall mount
bracket MSW240
LSW350B
MSW240
Model 49LF51**
42/47/50/55LF56**
42/49/55LF55**
42/49/55LF62**
VESA (A x B) 400 x 400
Standard screw M6
Number of screws 4
Wall mount
bracket
LSW440B
MSW240
Model
VESA (A x B)
Standard screw
Number of screws
Wall mount
bracket
A
B
ENGLISH
t Disconnect the power rst, and then move or install the TV.
Otherwise electric shock may occur.
t Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
t If you install the TV on a ceiling or slanted wall, it may fall and
result in severe injury. Use an authorised LG wall mount and
contact the local dealer or qualied personnel.
t Do not over tighten the screws as this may cause damage to the TV
and void your warranty.
t Use the screws and wall mounts that meet the VESA standard. Any
damages or injuries by misuse or using an improper accessory are
not covered by the warranty.
TE
t Use the screws that are listed on the VESA standard screw
specications.
t The wall mount kit includes an installation manual and necessary
parts.
t The wall mount bracket is not provided. You can obtain additional
accessories from your local dealer.
t The length of screws may dier depending on the wall mount.
Make sure to use the proper length.
t For more information, refer to the manual supplied with the wall
mount.
t When installing the wall mounting bracket, use the adhesive
label provided. The adhesive label will protect the opening from
accumulating dust and dirt. (Only when the label is provided)
When attaching a wall mounting bracket to the TV, insert the wall
mount spacers into the TV wall mount holes to adjust the vertical
angle of the TV. (Only when the item of the following form is
provided)
Provided Item
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external devices
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
TE
t The external device connection may dier from the model.
t Connect external devices to the TV regardless of the order of the
TV port.
t If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
t Refer to the external equipment’s manual for operating
instructions.
t If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
t In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
t In PC mode, some resolution settings may not work properly
depending on the graphics card.
t If ULTRA HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Only UF67**)
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
t Use a signal splitter to use more than 2 TVs.
t If the image quality is poor, install a signal amplier properly to
improve the image quality.
t If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
t An antenna cable and converter are not supplied.
t Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
t For a location that is not supported with Ultra HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly. This TV cannot
receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because
the related standards have not been conrmed. (Only UF67**)
ENGLISH
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
HDMI ULTRA HD deep colour
settings
(Only UF67**)
t SETTINGS
PICTURE HDMI ULTRA HD Deep Colour
HDMI (1/2) ULTRA HD Deep Colour
- On : Support 4 K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4 K @ 50/60 Hz (4:2:0)
t All HDMI ports support the HDCP 2.2.
t 4 K Source is only supported in HDMI input.
t 4 K signal and content are not available in the RF/USB input.
t All HDMI input ports support 4 K @ 50/60 Hz (For details on the
supported specications, refer to the table below.) for high-
denition video. Picture or sound may not be supported depending
on the specications of the external device connected. In that case,
change the settings for HDMI Deep Colour
upport Format
Resolution
Frame rate
(Hz)
Colour Depth /
Chroma Sampling
8 bit 10 bit 12 bit
3840 x 2160p
4096 x 2160p
50.00
59.94
60.00
YCbCr 4:2:0 YCbCr 4:2:0
1
YCbCr 4:2:2
1
YCbCr 4:4:4
1
- -
RGB 4:4:4
1
- -
1 : Only supported when
HDMI ULTRA HD Deep Colour On
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
t Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
t If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
Euro Scart connection
(Depending on model)
Transmits the video and audio signals from an external device to the
TV set. Connect the external device and the TV set with the euro scart
cable.
Type
Current
input mode
AV1
(TV Out
1
)
Digital TV Digital TV
Analogue TV, AV
Analogue TVComponent
HDMI
1 TV Out : Outputs Analogue TV or Digital TV signals.
t Any Euro scart cable used must be signal shielded.
t When watching digital TV in 3D imaging mode, only 2D out signals
can be output through the SCART cable. (Only 3D models)
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
Remote control
(Depending on model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the
and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
t Do not mix old and new batteries, as this may damage the remote
control.
t The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor
on the TV.
ENGLISH
B
1 2
3
(POWER)
alls your preferred subtitle in digital mode.
1
be enabled. (Depending on model)
1
ws programme guide. (Depending on model)
2
es an image. (Depending on model)
2
Changes the input source.
Number buttons
o the previously viewed programme.
B
3
ws programme guide. (Depending on model)
3
es all sounds.
Moves to the previous or next screen.
C
D
4
Teletext buttons ( )
teletext.
screen.
Navigation buttons (up/down/left/right)
or options.
o the previous level.
Clears on-screen displays and returns to TV viewing.
D
4
Selects an AV mode. (Depending on model)
4
By pressing the AD button, audio descriptions function will
be enabled. (Depending on model)
(Only Time Machine
Ready
supported model) (Depending on model)
Control buttons ( )
menus, Time Machine
Ready
control or the SIMPLINK compatible
devices (USB, SIMPLINK or Time Machine
Ready
).
Coloured buttons
(
, reen, lue)
ENGLISH
Licenses
Supported licenses may dier by model. For more information about
licenses, visit www.lg.com.
tured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
testing to ensure it plays DivX® video.
To play purchased DivX movies, rst register your
device at vod.divx.com. Find your registration code in
the DivX VOD section of your device setup menu.
DivX Certied® to play DivX® video up to HD 1080p,
including premium content.
DivX®, DivX Certied® and associated logos are
trademarks of DivX, LLC and are used under license.
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274.
(Only UF67**)
http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks, and DTS 2.0+Digital Out
is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
[email protected]om. This oer is valid for three (3) years from the date
on which you purchased the product.
Settings
Automatically Setting Up Programme
SETTINGS
SETUP Auto Tuning
Automatically tunes the programmes.
t If Input Source is not connected properly, programme registration
may not work.
t Auto Tuning ogrammes that are currently
broadcasting.
t If Lock System -up window will appear asking
for password.
To select Picture Mode
SETTINGS
PICTURE Picture Mode
programme.
t Vivid eightens contrast, brightness and sharpness to display
vivid images.
t Standard isplays images in standard levels of contrast,
brightness and sharpness.
t Eco/APS epending on model]
The Energy Saver feature changes settings on the TV to reduce
power consumption.
t Cinema/Game isplays the optimum picture for movie, game.
t Sport epending on model] Optimizes the video image for
high and dynamic actions by emphasizing primary colours such as
white, grass, or sky blue.
ENGLISH
Expert 1, 2 or adjusting picture quality that
allows experts and amateurs to enjoy the best TV viewing. This
is the adjustment menu provided for ISF-certied picture tuning
professionals. (ISF logo can only be used on ISF-certied TVs.)
ISFccc: Imaging Science Foundation Certied Calibration Control
t Depending on input signal, available range of picture modes may
dier.
t t mode is for picture tuning professionals to control
and ne-tune using a specic image. For normal images, the eects
may not be dramatic.
t The ISF function is only available on some models.
To set advanced control
SETTINGS
PICTURE Picture Mode Advanced Control /
Expert Control
for a special screen. First select a Picture Mode our choice.
t Dynamic Contrast djusts the contrast to the optimal level
according to the brightness of the image.
t Dynamic Colour djusts colours to make the image appear in
more natural colours.
t Skin Colour ets Skin colour spectrum separately to implement
the skin colour as dened by the user.
t Sky Colour olour is set separately.
t Grass Colour tural colour spectrum (meadows, hills, etc.) can
be separately set.
t Gamma ets the gradation curve according to the output of
picture signal in relation to the input signal.
t Colour Gamut
t Edge Enhancer ws clearer and distinctive yet natural edges
of the video.
t Expert Pattern epending on model]
Patterns used for expert adjustment.
t Colour Filter ilters a specic colour spectrum in RGB colours to
ne-tune colour saturation and hue accurately.
t Colour Temperature djusts the overall tone of the screen as
desired. In Expert mode, detailed ne-tuning can be set via Gamma
method, etc.
t Colour Management System This is a system that experts use
when they adjust colour with a test pattern. They can select from six
colour areas (Red / Green / Blue / Cyan / Magenta / Yellow) without
aecting other colours. For normal images, adjustments may not
result in noticeable colour changes.
t Super Resolution epending on model]
Adjusts the resolution to make dim and blurred images clearer.
t Depending on input signal or other picture settings, the range of
detailed items for adjustment may dier.
To set additional picture options
SETTINGS
PICTURE Picture Mode Picture Option
Adjusts detailed setting for images.
t Noise Reduction liminates noise in the picture.
t MPEG Noise Reduction liminates noise generated while
creating digital picture signals.
t Black Level djusts the brightness and contrast of the screen
to suit the black level of the input picture by using the blackness
(black level) of the screen.
t Real Cinema ptimizes the screen for movie viewing.
t Motion Eye Care / Smart Energy Saving epending on
model] Saves power consumption by adjusting the brightness
corresponding to the movement of the image on the screen.
t LED Local Dimming epending on model] Brightens bright
areas and darkens dark areas of the image for maximum contrast
and minimum blur while reducing power consumption.
- Off isables the LED Local Dimming function.
- Low/Medium/High hanges the contrast ratio.
t TruMotion epending on model] Optimizes the image quality
of fast-moving pictures.
- Off :
- Smooth oftens fast-moving pictures.
- Clear es fast-moving pictures clearer.
- User ets De-Judder/De-Blur manually.
De-Judder: Adjusts juddering on the screen.
De-Blur: Reduces the blurring eects of motion.
Auto means Juddering and blurring range that depend on input
video status is controlled by TruMotion mode.
t Depending on input signal or other picture settings, the range of
detailed items for adjustment may dier.
To use Energy Saving feature
SETTINGS
PICTURE Energy Saving
es power consumption by adjusting screen brightness.
t Auto epending on model]
The TV sensor detects the ambient lighting and automatically
adjusts the screen brightness.
t Off Turns o the Energy Saving mode.
t Minimum / Medium / Maximum pplies the pre-set Energy
Saving mode.
t Screen Off creen is turned o and only sound is played. Press
any button except Power button on the remote control to turn the
screen back on.
ENGLISH
To use HDMI ULTRA HD Deep Colour
SETTINGS
PICTURE HDMI ULTRA HD Deep Colour HDMI
(1/2) ULTRA HD Deep Colour
HDMI port provides ULTRA HD Deep Colour, HDMI port provides ULTRA
HD Deep Colour for a clearer picture.
t On TRA HD Deep Colour enabled
t Off TRA HD Deep Colour disabled
To use TV speaker
SETTINGS
AUDIO Sound Out TV Speaker / ernal TV
Speaker
Sound is output through the TV speaker.
To use External Speaker
SETTINGS
AUDIO Sound Out External Speaker (Optical)
/ Audio Out (Optical)
Sound is output through the speaker connected to the optical port.
t SimpLink is supported.
To use Internal TV Speaker + Audio Out (Optical)
SETTINGS
AUDIO Sound Out Internal TV Speaker +
Audio Out (Optical)
Audio is played through the TV’s built-in speakers and the audio device
connected to the digital optical audio output port simultaneously.
To use Digital Sound Out
SETTINGS AUDIO Sound Out External Speaker (Optical)
/ Audio Out (Optical) / Internal TV Speaker + Audio Out (Optical)
Digital Sound Out
Sets up Digital Sound Out.
Audio Input Digital Audio Ouput
Auto
MPEG
Dolby Digital
Dolby Digital Plus
HE-AAC
DTS
PCM
Dolby Digital
Dolby Digital
Dolby Digital
DTS
PCM All PCM
To connect and use LG audio device
SETTINGS AUDIO Sound Out LG Sound Sync (Optical)
Connect LG audio device with the o the optical digital
audio output port. LG audio device allows you to enjoy rich powerful
sound easily.
To use Headphone
SETTINGS AUDIO Sound Out Headphone
Sound is output through the headphone connected to the earphone/
headphone port.
To synchronize audio and video
SETTINGS AUDIO AV Sync. Adjust
Synchronizes video and audio directly when they do not match.
t If you set
AV Sync. Adjust ON ou can adjust the sound output
(TV speakers or SPDIF) to the screen image.
To use SIMPLINK
[Depending on model]
SIMPLINK is a feature that enables you to control and manage various
multimedia devices conveniently via the SIMPLINK menu.
ENGLISH
Connect the TV’s HDMI IN
output terminal using an HDMI cable.
t [Depending on model]
For home theatre units with a SIMPLINK function, connect HDMI
terminals as above, and use an optical cable to connect Optical
Digital Audio Out from the TV to Optical Digital Audio In of the
SIMPLINK device.
2 Select INPUT(OPTION) SIMPLINK
SIMPLINK menu window appears.
3 In SIMPLINK Setting window, set SIMPLINK function to ON
4 In SIMPLINK menu window, selects the device you want to control.
t This function is only compatible with devices with the SIMPLINK
logo.
t To use the SIMPLINK function, you need to use a high-speed HDMI®
cable (with CEC (Consumer Electronics Control) feature added).
High-speed HDMI® cables have the No. 13 pin connected for
information exchange between devices.
t If you switch to another input, the SIMPLINK device will stop.
t If a third-party device with the HDMI-CEC function is also used, the
SIMPLINK device may not work normally.
t [Depending on model]
If you select or play media from a the device with a home theatre
function, the HT Speaker(Speaker) omatically connected.
Be sure to connect with an optical cable (sold separately) to use the
HT Speaker(Speaker) tion.
SIMPLINK function description
t
Direct Play ys the multimedia device on the TV instantly.
t Select multimedia device elects the desired device via the
SIMPLINK menu to control it from the TV screen instantly.
t
Disc playback e with the TV
remote control.
t Power off all devices When you power o the TV, all connected
devices are turned o.
t
Sync Power on When the equipment with SIMPLINK function
connected HDMI terminal starts to play, the TV will automatically
turn on.
t
Speaker epending on model]
Select speaker either on the home theatre unit or the TV.
To set password
SETTINGS LOCK Set Password
The initial password is set to ‘0000’.
t When France is selected for Country, password is not ‘0000’ but
‘1234’.
t When France is selected for Country, password cannot be set to
‘0000’.
To return Factory Reset
SETTINGS OPTION Factory Reset
The TV turns itself o and back on, and all settings are reset.
t When
Lock System e, a pop-up window appears and asks
for password.
t Do not turn o the power during initialization.
To remove the USB device
Q.MENU USB Device
When you see a message that the USB device has been removed,
separate the device from the TV.
t Once a USB device has been selected for removal, it can no longer
be read. Remove the USB storage device and then re-connect it.
Using a USB storage device - warning
t If the USB storage device has a built-in auto recognition program
or uses its own driver, it may not work.
t Some USB storage devices may not work or may work incorrectly.
t Use only USB storage devices formatted with the Windows FAT32
or NTFS File System.
t For external USB HDDs, it is recommended that you use devices
with a rated voltage of less than 5 V and a rated current of less
than 500 mA.
t It is recommended that you use USB memory sticks of 32 GB or less
and USB HDDs of 2 TB or less.
ENGLISH
t If a USB HDD with power-saving function does not work properly,
turn the power o and on. For more information, refer to the user
manual of the USB HDD.
t Data in the USB storage device can be damaged, so be sure to back
up important les to other devices. Data maintenance is the user’s
responsibility and the manufacturer is not responsible for data loss.
My Media supporting le
t Maximum data transfer rate : 20 Mbps (Mega bit per second)
t External supported subtitle formats : *.srt (SubRip), *.smi (SAMI),
*.sub (SubViewer, MicroDVD, DVDsubtitleSystem, SubIdx(Vobsub)),
*.ass/*.ssa (SubStation Alpha), *.txt (TMplayer), *.psb (PowerDivX)
t Internal supported subtitle formats: *.dat/*.mpg/*.mpeg/*.
vob (DVD Subtitle), *.ts/*.tp/*.m2ts/ (DVB Subtitle), *.mp4 (DVD
Subtitle, UTF-8 Plain Text), *.mkv (ASS, SSA, UTF-8 Plain Text,
Universal Subtitle Format, VobSub, DVD Subtitle), *.divx/*.avi
(XSUB
1
, XSUB+)
1 XSUB : Supports internal subtitles generated from DivX6
Supported Video Formats
t Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)
t .asf, .wmv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XViD, H.264/AVC, VC1(WMV3, WVC1), MP43
[Audio] WMA Standard, WMA9(Pro), MP3, AAC, AC3, MP3, 3D WMV
Single Stream.
t divx, .avi
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XViD, H.264/AVC
[Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I, MPEG-1 Layer II,
Dolby Digital, MPEG-1 Layer III (MP3), *DTS
t .ts, .trp, .tp, .mts, .m2ts
[Video] H.264/AVC, MPEG-2, AVS, VC1
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, MPEG-1 Layer III (MP3),
Dolby Digital, Dolby Digital Plus, AAC, HE-AAC, *DTS
t .vob
[Video] MPEG-1, MPEG-2
[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1 Layer II, DVD-LPCM
t .mp4, .m4v, .mov
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XVID, H.264/AVC
[Audio] AAC, MPEG-1 Layer III (MP3), *DTS
t .mkv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XVID, H.264/AVC
[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III (MP3), *DTS, LPCM
t motion JPEG
[Video] MJPEG
[Audio] LPCM, ADPCM
t .mpg, .mpeg, .mpe
[Video] MPEG-1, MPEG-2
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby Digital, LPCM
t dat
[Video] MPEG-1, MPEG-2
[Audio] MP2
t v
[Video] Sorenson H.263, H.264/AVC
[Audio] MP3, AAC, HE-AAC
t *rm, *rmvb
[Video] RV30, RV40
[Audio] Dolby Digital, AAC, HE-AAC, RA6(Cook)
t 3gp, 3gp2
[Video] H.264/AVC, MPEG-4 Part2
[Audio] AAC, AMR(NB/WB)
t *DTS / *rm / *rmvb : Depending on model
Supported Audio Formats
t File type : mp3
[Bit rate] 32 Kbps - 320 Kbps
[Sample freq.] 16 kHz - 48 kHz
[Support] MPEG1, MPEG2, Layer2, Layer3
t File Type : AAC
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] ADIF, ADTS
t File Type : M4A
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] MPEG-4
t File Type : WMA
[Bit rate] 128 Kbps ~ 320 Kbps
[Sample freq.] 8 kHz ~ 48 kHz
[Support] WMA7, WMA8, WMA9 Standard
t File Type : WMA10 Pro
[Bit rate] ~ 768 Kbps
[Channel / Sample freq.]
M0 : up to 2 Channel @ 48 kHz
(Except LBR mode),
M1 : up to 5.1 Channel @ 48 kHz,
M2 : up to 5.1 Channel @ 96 kHz
[Support] WMA10 Pro
t File Type : OGG
[Bit rate] Free Format
[Sample freq.] ~ 48 kHz
[Support] OGG Vorvis
ENGLISH
orted Photo Formats
t Category : 2D (jpeg, jpg, jpe), 3D (jps)
[Available le type] SOF0: Baseline,
SOF1 : Extend Sequential,
SOF2 : Progressive
[Photo size] Minimum : 64 x 64,
Maximum : Normal Type: 15360 (W) x 8640 (H),
Progressive Type : 1920 (W) x 1440 (H)
t Category : BMP
[Photo size] Minimum : 64 x 64, Maximum : 9600 x 6400
t Category : PNG
[Available le type] Interlace, Non-Interlace
[Photo size] Minimum : 64 x 64, Maximum : Interlace : 1200 x 800,
Non-Interlace : 9600 x 6400
t Category : MPO (3D)
[Photo size] 4:3 Size : 3648 x 2736 / 2592 x 1944 / 2048 x 1536,
3:2 Size : 3648 x 2432
t BMP and PNG format les may be slower to display than JPEG.
t The 3D function may dier depending on the model.
To see web manual
To obtain detailed User Guide information, please visit www.lg.com.
External control device
setup
To obtain the external control device setup information, please visit
www.lg.com.
Troubleshooting
Cannot control the TV with the remote control.
t Check the remote control sensor on the product and try again.
t Check if there is any obstacle between the product and the remote
control.
t Check if the batteries are still working and properly installed (
to
, to ).
No image display and no sound is produced.
t Check if the product is turned on.
t Check if the power cord is connected to a wall outlet.
t Check if there is a problem in the wall outlet by connecting other
products.
The TV turns o suddenly.
t Check the power control settings. The power supply may be
interrupted.
t Check if the
Automatic Standby Sleep
Timer Off Time tivated in the TIME .
t If there is no signal while the TV is on, the TV will turn o
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is
displayed.
t Turn the TV o/on using the remote control.
t Reconnect the HDMI cable.
t Restart the PC with the TV on.
1 / 1

LG 40UF671V Kasutusjuhend

Kategooria
LCD-telerid
Tüüp
Kasutusjuhend