© MuxLab Inc. 94-000672-A SE-000672-B
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com URL: www.muxlab.com
Specifications
Environment
HDMI 1.3a
Devices
DVD, plasma, projectors, monitors, TV, PC, laptops, servers
supporting HDMI.
Transmission
Transparent to the user
Bandwidth
340 MHz
Signals
HDMI 1.3a protocol
Connectors
One (1) HDMI receptacle.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
3.5mm jacks for IR emitter and sensor
Note: HDMI cables not included.
Maximum Distance
Based on a maximum
length of 6.6 ft (2 m) of
HDMI cable per end.
480i/p: Cat 5e/6: 330 ft (100 m)
720p, 1080i: Cat 5e/6: 330 ft (100 m)
1080p: Cat 5e/6: 330 ft (100 m)
1080p Deep Color: Cat 5e/6: 330 ft (100 m)
Note: When installed in an electrically noisy environment, an STP
cable must be used. Also, cross-connection reduces the effective
distance depending on the grade of twisted cable used.
RJ45 Pin
Configuration
Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight-
through wiring.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable
One (1) Cat 5e/6 or better twisted pair cables required
Power Supply
Two (2) 110-240V/5VDC power supplies with interchangeable blades
Power Consumption
Transmitter: 3.0 Watt Receiver: 5.0 Watt
Temperature
Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Enclosure
Aluminum
Dimensions
4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)
Weight
2.6 lb (1.2 kg)
Compliance
Regulatory: FCC, CE, RoHS Flammability: 94V0
Warranty
2 years
Order Information
500450 HDMI Mono Extender Kit
HDMI Mono Extender Kit
500450
Quick Installation Guide
Overview
The HDMI Mono Extender Kit (500450) allows HDMI equipment to be connected up
to 330 ft (110 m) @ 1080p Deep Color via one (1) Cat 5e/6 unshielded twisted pair
cables in a point-to-point configuration. The kit comes with one (1) Transmitter and one
(1) Receiver as well as an IR Emitter (500998) and IR Sensor (500999) for remote
control applications.
Applications
Applications include commercial and residential AV systems, classroom projector
systems, digital signage, boardroom systems, collaborative PC systems, and medical
information systems.
Installation
1. Identify the connectors on the Transmitter and Receiver as indicated on the product
labels.
© MuxLab Inc. 2012
2. Verify that the distance between the HDMI Transmitter and Receiver is within
MuxLab specifications (see Specifications table).
3. To install the Transmitter:
3a. Connect the Transmitter to the HDMI video source with an HDMI compliant
cable.
3b. Connect one (1) lengths of Cat 5e/6 (or higher) grade UTP cables to
RJ45 LINK connectors on the Transmitter.
4. To install the Receiver:
4a. Connect the Receiver to the HDMI display equipment with an HDMI compliant
cable.
4b. Connect the one (1) Cat 5e/6 cables to RJ45 LINK connectors on the Receiver.
5. Connect the 5 VDC power supply to the Receiver first, and then plug the power
supply into an AC power outlet. Connect the 5 VDC power supply to the
Transmitter first, and then plug the power supply into an AC power outlet. If power
is present, the green power LED of the Transmitter and the Receiver will be ON.
Note: Power the HDMI Mono Extender Balun only after all connections are made.
6. Power the HDMI equipment and verify the image quality.
7. If infrared remote control is needed, connect the IR Sensor to the 3.5mm Stereo
Jack of the receiver and the IR Emitter to the 3.5mm Mono Jack of the Transmitter.
Note: You can differentiate the IR Sensor and the IR Emitter by looking at the
3.5 mm plug. The IR Sensor is using a Stereo Plug (3 Contacts) and the IR
Emitter a mono plug (2 Contacts).
8. Position the IR Sensor so that it is directed to the hand-held remote control. For a
clear IR signal reception, aim the hand-held remote control to the top of the IR
Sensor enclosure.
9. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD
player). For a clear IR signal reception, the IR Emitter can be glued on the source’s
IR Sensor. The IR Emitter’s signal is transmitted from the side of the enclosure.
10. The following diagram shows the final configuration.
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
in respect to the installation of the HDMI Mono Extender Kit:
Symptom
Tx LEDs
Rx LEDs
Probable
Cause
Possible
Solutions
Power
HDMI
RJ45
Power
HDMI
RJ45
No Image
OFF
OFF
OFF
OFF
OFF
OFF
No power
• Check power
connections
No Image
ON
OFF
OFF
ON
OFF
OFF
UTP Cable
• Check the UTP
cables.
No Image
ON
OFF
ON
ON
OFF
ON
HDMI Cable
• Check the HDMI
Cable.
No Image
ON
ON
ON
ON
ON
ON
Synchronization
• Check cable length.
Flickering
Image
ON
ON
ON
ON
ON
ON
Synchronization
• Check cable length
• Check the HDMI
Cable Quality.
Choppy sound
ON
ON
ON
ON
ON
ON
Synchronization
• Check cable length
• Check the HDMI
Cable Quality.
Green or pink
hue
ON
ON
ON
ON
ON
ON
DDC
communication
• Cycle power of the
HDMI Extender.
• Check UTP cables
and replace.
Image flickers
when powering
up nearby
equipment
ON
ON
ON
ON
ON
ON
Interference
• Use STP cables
IR not
functioning
ON
ON
ON
ON
ON
ON
Remote control
not directed to
the IR Sensor or
IR Emitter not
directed to the
source.
• Make sure the IR
Sensor is directed
towards the remote
and the IR Emitter
to the equipment
IR not
functioning
ON
ON
ON
ON
ON
ON
Interference
from sunlight,
Fluorescent,
Neon or
Halogen lights
• Place the IR
equipment away for
the interfering light
IR not
functioning
ON
OFF
OFF
ON
OFF
OFF
Interference
from RF
radiation from
the TV
• Place the IR
equipment away for
the RF radiation
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
-
1
-
2
teistes keeltes
- English: MuxLab 500450 Installation guide
Seotud paberid
-
MuxLab HDMI Extender Kit Long-Reach paigaldusjuhend
-
MuxLab HDMI Extender Kit, HDBaseT Lite, UHD-4K, PoE paigaldusjuhend
-
MuxLab HDMI Extender Kit, HDBT, UHD-4K paigaldusjuhend
-
MuxLab HDMI/RS232 Extender Kit, HDBT, 4K/60 paigaldusjuhend
-
MuxLab HDMI/RS232 Extender Kit paigaldusjuhend
-
MuxLab HDMI Extender Pair, HD Kasutusjuhend
-
MuxLab HDMI / USB 2.0 Extender Kit, HDBT, 4K60 paigaldusjuhend
-
MuxLab 100504 paigaldusjuhend
-
MuxLab DVI / USB2.0 HDBaseT Extender Kit paigaldusjuhend
