Leht laaditakse ...
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80014293 Rev -
030670-00 (1200A)
030671-00 & 030685-00 (2200A)
030672-00 & 030686-00 (3200A)
030673-00 (6200A)
Copyright © 2015. Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA
en - English
ar -
da - Dansk
es - Español
fi - Suomi
fr - Français
hu - Magyar
nl - Nederlands
no - Norsk
pl - Polski
ru -
sv - Svenska
sw - Kiswahili
2 BRIGGSandSTRATTON.COM
C
A
Q
F
B
J
1
K
L
2
A
3
FUEL
TANK
C
B
A
4
D
H
M
N
P
G
E
3
Safety and Control Symbols ................... 3
Equipment Description........................ 3
Features and Controls ........................ 3
Operation................................... 4
Maintenance ................................ 6
Storage .................................... 7
Troubleshooting ............................. 8
Specifications ............................... 8
Warranty ................................... 9
The safety alert symbol indicates a potential personal
injury hazard. A safety symbol may be used to represent
the type of hazard. WARNING indicates a hazard which,
if not avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided, could
result in minor or moderate injury. NOTICE address
practices not related to personal injury.
The outdoor generator is an engine-driven, revolving
field, alternating current (AC) generator equipped with a
voltage regulator. The voltage regulator is designed to
automatically maintain output voltage level. It is designed
to supply electrical power for operating compatible
electrical lighting, appliances, tools and motor loads.
This machine is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use,
ask dealer or contact authorized service center. This
equipment is designed to be used with Briggs & Stratton
Power Products authorized parts ONLY.
The generator has a system ground that connects the
generator frame components to the ground terminals
on the AC output receptacles. The generator neutral
is floating, which means that the AC stator winding
is isolated from the grounding fastener and the AC
receptacle ground pins. Electrical devices, such as RCD,
requiring a grounded neutral may not operate properly
from this generator.
There may be regulations, local codes, or ordinances
that apply to the intended use of the generator. Please
consult a qualified electrician, electrical inspector, or the
local agency having jurisdiction.
This generator is not intended to be used at a
construction site.
Figure
1
A Fuel Tank J Oil Drain Plug
B Engine Switch K Air Filter
C Circuit Breaker L Choke Lever
D Main Breaker (6200A
ONLY)
M Recoil Starter
E 230 Volt AC, 16 Amp,
Shuko Receptacle
N Fuel Valve
F Grounding Fastener P Identification Label
G Engine Identification Q Spark Arrester Muffler
H Oil Fill Cap/Dipstick
Fire
Explosion
Toxic Fumes
Hot Surface
Electrical Shock
Safety Alert
Symbol
Instruction Manual
Oil Level
Carbon
Monoxide Alarm
Circuit Breaker
On
Ground Terminal
Floating
Neutral
Off
Fuel
Engine Control
!
Do Not Start
Engine
Choke
Run
Suffication
Suffication
Oil
4 BRIGGSandSTRATTON.COM
Before starting the portable generator there are two
equally important safety concerns regarding carbon
monoxide poisoning and fire that must be addressed.
THE RISK OF CARBON MONOXIDE POISONING
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas. Operate this product
only outdoors far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from
accumulating and potentially being drawn towards
occupied spaces. Install battery-operated carbon
monoxide alarms or plug-in carbon monoxide alarms with
battery back-up according to the manufacturer’s
instructions. Smoke alarms cannot detect carbon
monoxide gas. Do not run this product inside homes,
garages, basements, crawlspaces, sheds, or other
partially-enclosed spaces even if using fans or opening
doors and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off. Always place this
product downwind and point the engine exhaust away
from occupied spaces. If you start to feel sick, dizzy, or
weak while using this product, get to fresh air right away.
See a doctor. You may have carbon monoxide
poisoning.
REDUCE THE RISK OF FIRE
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
Portable generator must be at least 1.5 m (5 ft.) from any
structure, overhang, trees, windows, doors, any wall
opening, shrubs, or vegetation over 30.5 cm (12 in.) in
height. Do not place portable generator under a deck or
other type of structure that may confine airflow. Smoke
alarm(s) must be installed and maintained indoors
according to the manufacturer’s instructions/
recommendations. Carbon monoxide alarms cannot detect
smoke. Do not place portable generator in manner other
than shown.
1.5 m
(5 ft.) min.
1.5 m (5 ft.) min.
MUFFLER
Install carbon monoxide alarms
inside your home. Without working
carbon monoxide alarms, you will
not realize you are getting sick
and dying from carbon monoxide.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER
MUFFLER
from home
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
CARBON MONOXIDE
ALARM(S)
Install carbon monoxide alarms
inside your home. Without working
carbon monoxide alarms, you will not
realize you are getting sick and dying
from carbon monoxide poisoning.
5
Figure
2
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF
or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
1
3
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure generator is on a level surface.
2. Clean area around oil fill (1,H) and remove oil fill
cap/dipstick.
3. Verify oil is at Full mark (3,A) on dipstick.
4. If needed, slowly pour oil into oil fill opening to Full
mark on dipstick. Do not overfill.
5. Replace and tighten oil fill cap/dipstick.
NOTICE Do not attempt to crank or start engine before
before it has been properly serviced with recommended
oil. This could result in an engine failure.
CAUTION Avoid prolonged or repeated skin contact
with used motor oil. Used motor oil has been shown to
cause skin cancer in certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON’T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel Figure
4
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline with a minimum of
87 octane.
• Gasoline with up to 10% ethanol content is acceptable.
NOTICE Do not mix oil in gasoline or modify engine to
run on alternate fuels. Do not use unapproved gasoline
such as E15 and E85. Use of unapproved fuels could
damage pressure washer and voids warranty.
See High Altitude for 1,524 m (5,000 ft.) and above.
WARNING! Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury. Do not
refuel during operation. Turn engine off and let it cool at
least 2 minutes before removing fuel cap. Fill fuel tank
outdoors. Do not spill fuel. If fuel spills, wait until it
evaporates before starting engine. Keep fuel away from
sparks, open flames, pilot lights, heat, and other ignition
sources. Check fuel lines, tank, cap and fittings
frequently for cracks or leaks. Replace if necessary. Do
not light a cigarette or smoke.
1. Slowly remove fuel cap to relieve pressure in tank.
2. Slowly add unleaded fuel (A) to fuel tank (B). Be
careful not to fill above lip (C). This allows adequate
space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
At altitudes over 1524 m (5,000 ft.), a minimum 85 octane
fuel is acceptable. To remain emissions compliant, high
altitude adjustment is required. Operation without this
adjustment will cause decreased performance, increased
fuel consumption, and increased emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the engine
at altitudes below 762 m (2,500 ft.) with the high altitude
kit is not recommended.
When transporting equipment with a vehicle or trailer,
turn fuel shutoff valve to OFF (0) position. Do not tip
engine or equipment at angle which causes fuel to spill.
1
Disconnect all electrical loads from the generator. Use
the following start instructions:
1. Make sure unit is outdoors on a level surface.
NOTICE Failure to operate the unit on a level surface
may cause the unit to shut down.
2. Rotate fuel valve (N) to ON (I) position.
3. Move choke lever (L) to CHOKE ( ) position.
NOTICE For a warm engine, be sure choke lever is in
RUN ( ) position.
4. Set engine switch (B) to ON (I) position.
5. Grasp recoil handle and pull slowly until slight
resistance is felt. Then pull rapidly to start engine.
6. As engine warms up, slowly move choke lever to
RUN ( ) position
NOTICE This unit is equipped with a low oil protection
device. Oil must be at proper level for engine to run. If
the engine oil drops below a preset level, an oil switch
will stop the engine. Check oil level with dipstick.
6 BRIGGSandSTRATTON.COM
1
Use only high quality, well-insulated extension cables in
accordance with IEC 245-4 with the generator’s 230 Volt
AC outlets. Inspect extension cables before each use.
Check that all extension cables are suitably rated and
are not damaged. When using extension cords under 40°
C, the total length of cords for a cross section of 1.5 mm²
should not exceed 50 m or for a cross section of 2.5 mm²
should not exceed 80 m.
WARNING! Damaged or overloaded extension
cords could overheat, arc, and burn resulting in
death or serious injury. Electrical equipment,
including cables and plug connections, should not be
defective.
NOTICE Ensure main breaker (D) (6200A ONLY) is in
ON (I) position. Connect electrical loads in off position
then turn on for operation.
Use receptacle (E) to operate 230 Volt AC, single-phase,
50 Hz electrical loads. The receptacle is protected
against overload by a push-to-reset circuit breaker (C).
Protection of electrical components depends on circuit
breakers specifically matched to the generator. Replace
circuit breaker with identical rating and performance
characteristics.
WARNING! Generator voltage could cause
electrical shock or burn resulting in death or
serious injury. Use a residual-current device
(RCD) in any damp or highly conductive area, such as
metal decking or steel work. Do not touch bare wires or
receptacles. Do not use generator with electrical cords
which are worn, frayed, bare or otherwise damaged. Do
not operate generator in the rain or wet weather. Do not
handle generator or electrical cords while standing in
water, while barefoot, or while hands or feet are wet. Do
not allow unqualified persons or children to operate or
service generator. Keep children a safe distance from
generator.
1. Turn off and unplug all electrical loads from generator
panel receptacles. Never stop engine with electrical
devices plugged in and turned on.
2. Let engine run at no-load for one minute to stabilize
internal temperatures of engine and generator.
3. Push engine switch to OFF (0) position.
4. Rotate fuel valve to OFF (0) position.
Follow hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions.
1
Service more often under dirty or dusty conditions.
Regular maintenance will improve performance and
extend the life of the outdoor generator. See any Briggs
& Stratton Authorized Service Dealer for service.
Installation and major repair work should only be
performed by specifically trained personnel.
The generator’s warranty does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the generator as instructed in this manual.
All service and adjustments should be made at least
once each season. A new spark plug and clean air filter
assure proper fuel-air mixture and help your engine
run better and last longer. Follow requirements in
Maintenance Schedule.
WARNING To ensure machine safety, use only
original spare parts from the manufacturer or approved
by the manufacturer. Should you have questions about
replacing components on your generator, please visit our
website at BRIGGSandSTRATTON.COM.
• Change engine oil
Every 8 Hours or Daily
• Clean debris
• Check engine oil level
Every 25 Hours or Yearly
• Clean engine air filter
1
Every 50 Hours or Yearly
• Change engine oil
1
Yearly
• Replace engine air filter
1
• Service fuel valve
• Service spark plug
• Inspect muffler and spark arrester
• Clean cooling system
1
7
Cleaning
Daily or before use, look around and underneath
generator for signs of oil or fuel leaks. Clean any
accumulated debris. Keep area around muffler free from
any debris.
• Use a soft bristle brush to loosen caked on dirt or
oil.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of generator could
damage it and shorten its life. Do not expose generator to
excessive moisture, dust, dirt, or corrosive vapors. Do not
insert any objects through cooling slots.
The engine exhaust muffler has a spark arrester screen.
Inspect the muffler for cracks, corrosion, or other
damage. Inspect spark arrester screen for damage or
carbon blockage. Clean if carbon blockage is found using
brush and commercial solvent or replace if damaged. If
damage is found, contact an authorized service dealer.
WARNING! Exhaust heat/gases could
ignite combustibles, structures or damage
fuel tank causing a fire, resulting in death
or serious injury. Contact with muffler area could cause
burns resulting in serious injury. Pay attention to the
warnings on the generator. Do not touch hot parts and
avoid hot exhaust gases.
If storing the unit for more than 30 days, use the following
guidelines to prepare it for storage.
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts. To keep fuel
fresh, use Briggs & Stratton® Advanced Formula Fuel
Treatment & Stabilizer, available wherever Briggs &
Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine outdoors for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine outdoors until it stops from lack of fuel.
The use of a fuel stabilizer in the storage container is
recommended to maintain freshness.
WARNING! Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury. When
storing fuel or equipment with fuel in tank, store away
from furnaces, stoves, water heaters, clothes dryers or
other appliances that have pilot light or other ignition
source because they could ignite fuel vapors. When
draining fuel, turn generator engine off and let it cool at
least 2 minutes before removing fuel cap. Loosen cap
slowly to relieve pressure in tank. Drain fuel tank
outdoors. Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources. Check fuel lines,
tank, cap and fittings frequently for cracks or leaks.
Replace if necessary.
Change Engine Oil
While engine is still warm, drain oil from crankcase. Refill
with recommended grade.
1. Clean the generator as outlined in Cleaning.
2. Store generator in clean, dry area and cover with a
suitable protective cover that does not retain moisture.
WARNING! Storage covers could cause a fire
resulting in death or serious injury. Do not place
a storage cover over a hot generator.Let
equipment cool for a sufficient time before placing the
cover on the equipment.
8 BRIGGSandSTRATTON.COM
Problem Cause
1. One of the circuit breakers is open.
2. Poor connection or defective cord set.
3. Connected device is bad.
1. Reset circuit breaker.
2. Check and repair.
3. Connect another device that is in
good condition.
1. Generator is overloaded.
1. Remove loads from generator.
down when running.
1. Engine switch set to OFF (0) position.
2. Fuel valve is in OFF (0) position.
3. Low oil level.
4. Dirty air cleaner.
5. Out of fuel.
6. Spark plug wire not connected to
spark plug.
7. Flooded with fuel.
1. Set switch to ON (I) position.
2. Turn fuel valve to ON (I) position.
3. Fill crankcase to proper level or
place generator on level surface.
4. Clean or replace air cleaner.
5. Fill fuel tank.
6. Connect wire to spark plug.
7. Wait 5 minutes and re-crank engine.
Model 1200A
Starting Surge ........................ 1,125 Watts
Wattage* ...............................900 Watts
AC Voltage at 230 Volts .................. 3.9 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . 50 Hz at 3600 rpm
Phase .............................. Single Phase
Displacement ..................79.8 cc (4.87 cu. in.)
Spark Plug Gap .................0.76 mm (0.030 in.)
Fuel Capacity ............5.7 Liters (1.5 U.S. Gallons)
Oil Capacity ...............0.35 Liters (11.8 Ounces)
Model 2200A
Starting Surge ........................ 2,125 Watts
Wattage* ............................. 1,700 Watts
AC Voltage at 230 Volts .................. 7.4 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . 50 Hz at 3600 rpm
Phase .............................. Single Phase
Displacement ..................196 cc (11.96 cu. in.)
Spark Plug Gap .................0.76 mm (0.030 in.)
Fuel Capacity .............11.4 Liters (3 U.S. Gallons)
Oil Capacity ..................0.6 Liters (20 Ounces)
Model 3200A
Starting Surge ........................ 3,125 Watts
Wattage* ............................. 2,500 Watts
AC Voltage at 230 Volts ................. 10.9 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . 50 Hz at 3600 rpm
Phase .............................. Single Phase
Displacement ..................196 cc (11.96 cu. in.)
Spark Plug Gap .................0.76 mm (0.030 in.)
Fuel Capacity .............11.4 Liters (3 U.S. Gallons)
Oil Capacity ..................0.6 Liters (20 Ounces)
Model 6200A
Starting Surge ........................ 6,125 Watts
Wattage* ............................. 4,900 Watts
AC Voltage at 230 Volts ................. 21.3 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . 50 Hz at 3600 rpm
Phase .............................. Single Phase
Displacement ..................389 cc (23.73 cu. in.)
Spark Plug Gap .................0.76 mm (0.030 in.)
Fuel Capacity .............18.9 Liters (5 U.S. Gallons)
Oil Capacity ..................1.1 Liters (37 Ounces)
The net torque rating for individual gasoline engine models is labeled in accordance with SAE (Society of
Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1349.
Net torque values are derived at 3600 RPM and are taken with exhaust and air cleaner installed. Given the wide array of conditions
in which they are placed, the gasoline engine may not develop the rated net torque when used in a given piece of power equipment.
This difference is due to a variety of factors including, but not limited to, the variety of application limitations, ambient operating
conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs
& Stratton may substitute an engine of higher rated torque for this engine.
* Generator per ISO 8528 Performance class G1 Reciprocating internal combustion engine driven alternating current generating sets.
Engine Oil Bottle ...............100005E or 100007E
Synthetic Oil Bottle ...................... 100007W
Fuel Stabilizer ...................992380 or 992381
For a full list of parts and diagrams, please visit BRIGGSandSTRATTON.COM.
9
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for
warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or
abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the
Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial
number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage
or water/chemical corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and
serviced or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by
warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when
normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine
brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine
or equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
- This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for
primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
80007708EN, Rev- ,
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WI, USA
WARRANTY PERIOD
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a
retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or mail the
complete registration card (if provided), or call 1-800-743-4115 (in USA).
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is
effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator
map at www.briggsandstratton.com. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service
Dealer for inspection and testing.
Liability for incidental or consequential damages are excluded to the extent exclusion is
permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state or country to country.**
Consumer Use Commercial Use
24 months None
BRIGGS & STRATTON PRODUCTS WARRANTY POLICY January 2014
3 . . . . . . . . . . . . . . . . . . . . . . . .
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 . . . . . . . . . . . . . . . . . . . . . . . . . .
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 . . . . . . . . . . . . . . . . . . . . . . . . .
8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Briggs & Stratton
1
A
J
B
L
C
K
D
6200A)
N
E
230 Shuko
16
M
F
P
G
Q
H
!
3
BRIGGSandSTRATTON.COM 2
5
2
2
Briggs & Stratton
SF
40
4
*
SAE 30
80
27
**
10W30
3
1
8
.1
H
1
.2
A3
.3
.4
.5
4
87
•
10%
•
.E85
E15
5000
1524
.1
B
A
.2
C
.3
5000
1524
85
Briggs & Stratton
2500
762
0
1
3
.1
I
N
.2
( )
L
.3
( )
I
B
.4
.5
( )
.6
BRIGGSandSTRATTON.COM 4
1
1.5
5
12 30.5
1.5
5
5 1.5
Install carbon monoxide alarms
inside your home. Without working
carbon monoxide alarms, you will
not realize you are getting sick
and dying from carbon monoxide.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER
7
•
•
30
30
Briggs & Stratton®
2
.1
.2
BRIGGSandSTRATTON.COM 6
1
4
IEC
230
245-4
40
50
²
1.5
²
2.5
80
6200A
D
I
16
230
Schuko
230
E
50
C
(RCD)
5
.1
.2
0
.3
0
.4
1
Briggs & Stratton
.BRIGGSandSTRATTON.COM
5
•
8
•
•
25
1
•
50
1
•
1
•
•
•
•
1
•
9
Briggs & Stratton
-
Briggs & Stratton
-
.
-
-
E15 E85
-
80007708AR, Rev- ,
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WI, USA
3
12
**
1300 274 447
BRIGGSandSTRATTON.COM
.Briggs &
;
Stratton Australia Pty Ltd
,
1 Moorebank Avenue
,
NSW
,
Australia
,
2170
www.onlineproductregistration.com
1-800-743-4115
.Briggs & Stratton
Briggs & Stratton
www.briggsandstratton.com
24
2014
BRIGGS & STRATTON
BRIGGSandSTRATTON.COM 8
.1
.2
.3
.1
.2
.3
.1
.1
0
.1
0
.2
.3
.4
.5
.6
.7
I
.1
I
.2
.3
.4
.5
.6
5
.7
1200A
1125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
900. . . . . . . . . . . . . . . . . . . . . . . . . . . *
3.9 . . . . . . . . . . . . . . .
230
360050 . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.87
79.8 . . . . . . . . . . . . . . . . . . .
0.030
0.76 . . . . . . . . . . . . . . . . . .
1.5
5.7 . . . . . . . . . . . . . . . . . . . . .
11.8
0.35 . . . . . . . . . . . . . . . . . . . . . . . . . .
2200A
2125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1700 . . . . . . . . . . . . . . . . . . . . . . . . . *
7.4 . . . . . . . . . . . . . . .
230
3600
50 . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.96
196 . . . . . . . . . . . . . . . . . .
0.030
0.76 . . . . . . . . . . . . . . . . . .
3
11.4 . . . . . . . . . . . . . . . . . . . . .
20
0.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3200A
3125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2500 . . . . . . . . . . . . . . . . . . . . . . . . . *
10.9 . . . . . . . . . . . . . .
230
3600
50 . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
196 . . . . . . . . . . . . . . . . . .
0.030
0.76 . . . . . . . . . . . . . . . . . .
3
11.4 . . . . . . . . . . . . . . . . . . . . .
20
0.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6200A
6125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4900 . . . . . . . . . . . . . . . . . . . . . . . . . *
21.3 . . . . . . . . . . . . . .
230
360050 . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.73
389 . . . . . . . . . . . . . . . . . .
0.030
0.76 . . . . . . . . . . . . . . . . . .
5
18.9 . . . . . . . . . . . . . . . . . . . . .
37
1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J1940
3600
J1349
SAE
Briggs & Stratton
G1
ISO 8528
*
100007E
100005E . . . . . . . . . . . . . . . . .
100007W . . . . . . . . . . . . . . . . . . . . . . . . .
992381
992380 . . . . . . . . . . . . . . . . . . . . . . . . .
.BRIGGSandSTRATTON.COM
3 BRIGGSandSTRATTON.COM
........... 3
.................. 3
...................... 3
.............................. 4
..................... 6
................................7
..............8
.............................. 8
.................................. 9
може
би могла
ВАЖНО
ВАЖНО
Briggs & Stratton Power Products.
1
A
J
B
K
C L
D
M
E 230 V AC, 16 A, Shuko
N
F
P
G
Q
H
!
4
Install carbon monoxide alarms
inside your home. Without working
carbon monoxide alarms, you will
not realize you are getting sick
and dying from carbon monoxide.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER
5 BRIGGSandSTRATTON.COM
2
1
3
1,H
3,A
ВАЖНО
4
ВАЖНО
Голяма надморска височина
A
(BC
1
ВАЖНО
N
L
(
).
ВАЖНО
).
B
)
ВАЖНО
/