Hilti TE 3000-AVR Kasutusjuhend

TE 3000-AVR

English 1

Français 11

Dansk 23

Svenska 33

Norsk 43

Suomi 53

Eesti 64

Latviešu 74

Lietuvių 84

Русский 95

Українська 107

Қазақ 119

Türkçe 131

ﻋﺮﺑﻲ 142

日本語 153

한국어 163

繁體中文 173

中文 182

1

2

3

4

5

6

7

8

TE 3000-AVR

en Originaloperatinginstructions....................................... 1

fr Moded'emploioriginal........................................... 11

da Originalbrugsanvisning .......................................... 23

sv Originalbruksanvisning........................................... 33

no Originalbruksanvisning .......................................... 43

fi Alkuperäisetohjeet ............................................. 53

et Originaalkasutusjuhend .......................................... 64

lv Oriģinālālietošanasinstrukcija ..................................... 74

lt Originalinaudojimoinstrukcija...................................... 84

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 95

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

tr Orijinalkullanımkılavuzu ......................................... 131

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 142

ja オリジナル取扱説明書 ............................................ 153

ko 오리지널사용설명서............................................. 163

zh 原始操作說明.................................................. 173

cn 原版操作说明.................................................. 182

*2228669* 2228669 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbers in illustrations refer to important work steps or to components important for the

work steps. In the text, the corresponding numbers draw attention to these work steps or compo-

nents, e.g. (3).

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

This symbol is intended to draw your special attention to certain points for handling the product.

2 English 2228669 *2228669*

1.3 Symbols on the product

1.3.1 Symbols on the product

The following symbols can be used on the product:

Protection class II (double-insulated)

Transport by crane is not permissible

Wireless data transfer

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Breaker TE 3000AVR

Generation 03

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

*2228669* 2228669 English 3

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

2.2 Hammer safety warnings

Safety instructions for all operations

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

▶Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power tool "live" and could give the operator an electric

shock.

4 English 2228669 *2228669*

2.3 Additional safety instructions

Personal safety

▶Use the product only when it is in technically faultless condition.

▶Never tamper with or modify the product in any way.

▶Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶Check that the side handle is fitted correctly and tightened securely. Always hold the tool with both

hands on the grips provided. Keep the grips dry, clean and free from oil and grease.

▶For this product, use only Hilti chisels with the TE-H connection end.

▶Change the chisel only when the power tool is in the horizontal position, never when it is vertical.

▶Push the chisel into the tool holder until it engages with an audible click and the yellow warning ring is

no longer visible.

▶Check that the chisel is correctly engaged. ATTENTION: A chisel not securely engaged in the chuck can

unexpectedly lead to dangerous situations!

▶Start this product only when it is in the working position, not in a transport position!

▶Take breaks between working and do physical exercises to improve the blood circulation in your fingers.

Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous

system in the fingers, hands and wrists.

▶The product is not intended for use by children, by debilitated persons or by persons who have received

no instruction or training.

▶Keep the power tool out of reach of children.

▶Before starting work, check the hazard class of the dust that will be produced when working. Use an

industrial vacuum cleaner with an officially approved protection classification in compliance with locally

applicable dust protection regulations.

▶Use a dust removal system and suitable mobile dust extractor whenever possible. Dust from materials

such as lead-based paint, certain types of wood and concrete/masonry/stone containing quartz, minerals

or metal can be harmful to health.

▶Make sure that the workplace is well ventilated and, where necessary, wear a dust mask appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust, such as oak and beech

dust, are classified as carcinogenic, especially in conjunction with additives for treating wood (chromate,

wood preservative). Only specialists are permitted to handle material containing asbestos.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the power tool can become live, presenting a risk of electric shock, if you

accidentally damage an electric cable.

▶Check the supply cord of this product at regular intervals and have it replaced by a qualified specialist

if found to be damaged. If the power tool’s supply cord is damaged it must be replaced with a

specially-prepared and approved supply cord available from Hilti Customer Service. Check extension

cords at regular intervals and replace them if found to be damaged. Do not touch the supply cord or

extension cord if it is damaged while working. Unplug the supply cord from the power outlet. Damaged

supply cords or extension cords present a risk of electric shock.

▶Dirty or dusty power tools that have been used frequently for work on conductive materials should

be checked at regular intervals by Hilti Service. Dust (especially dust from conductive materials) or

dampness adhering to the surface of the tool may, under unfavorable conditions, lead to electric shock.

▶Switch the power tool off and unplug the supply cord in the event of a power failure or interruption in the

electricity supply. This will prevent accidental restarting when power returns.

*2228669* 2228669 English 5

3 Description

3.1 Product overview 1

@Grip with on/off switch

;Service indicator

=Carrying handle

%Grip

&Supply cord connector

(Supply cord with keyed plug connector

)Air vents

+Tool holder

3.2 Overview of the transport trolley 2

@Grip

;Load retainer

=Locking bar

%Holder for accessory tools (chisels)

&Wheels

(Wheel securing parts (washer, retaining pin)

)Power tool locating pin

+Carrying handle

3.3 Intended use

The product described is a hand-held electric breaker with 28 mm hex tool holder. It is designed for chiseling

work on concrete, masonry and asphalt. Excavation and compacting are further possible applications.

▶Operation is permissible only when connected to a power source providing a voltage and frequency in

compliance with the information given on the type identification plate.

3.4 Possible misuse

This product is not suitable for working on hazardous materials.

This product is not suitable for working in a damp environment.

3.5 Service indicator

The breaker is equipped with a service indicator LED.

Status Meaning

The service indicator lights red. • End of service interval – servicing is due. Bring

the product to Hilti Service.

• The product is faulty. Bring the product to Hilti

Service.

Service indicator flashes red. • Temporary fault. Wait 10 seconds for the

flashing to stop.

• If the flashing does not stop within 10 seconds,

unplug the supply cord from the power supply

and wait for 2 minutes.

• If the flashing does not stop, bring the product

to Hilti Service.

6 English 2228669 *2228669*

Status Meaning

"Ready for operation" indicator flashes green. • The overheating prevention cut-out has been

activated.

• Allow the product to cool down.

"Ready for operation" indicator shows green. Product is ready for use.

Bring the product to Hilti Service in good time. This will help to ensure that it’s always ready for use.

3.6 Active Vibration Reduction

The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.

3.7 Items supplied

Electric breaker, operating instructions, grease.

The transport trolley is available as an accessory.

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

4 Technical data

For details of the rated voltage, current, frequency and/or input power, please refer to the power tool’s

country-specific type identification plate.

When powered by a generator or transformer, the generator or transformer’s power output must be at least

twice the rated input power shown on the rating plate of the power tool. The operating voltage of the

transformer or generator must always be within +5% and -15% of the rated voltage of the power tool.

Rated current input 9 A

Weight in accordance with EPTA procedure 01 27.1 kg

Single impact energy in accordance with EPTA procedure 85 J

Storage temperature −20 ℃ … 70 ℃

Ambient temperature for operation −20 ℃ … 55 ℃

4.1 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the power tool is switched

off, or when it is running but not actually being used for a job. This can significantly reduce exposure over

the total working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise information

TE 3000AVR

Sound power level (LWA)106 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A)

Sound pressure level (LpA)95 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A)

*2228669* 2228669 English 7

Vibration information

TE 3000AVR

Chiseling (ah, Cheq)6.3 m/s²

Uncertainty (K) 1.5 m/s²

4.2 Using extension cords

WARNING

A damaged supply cord presents a hazard! Do not touch the supply cord or extension cord if damaged

while working. Disconnect the supply cord plug from the power outlet.

▶Check the appliance’s supply cord at regular intervals and have it replaced by a qualified specialist if

found to be damaged.

• Use only extension cords of a type approved for the application and with conductors of adequate gauge

(cross section). The power tool may otherwise suffer a drop in performance and the extension cord may

overheat.

• Check the extension cord for damage at regular intervals.

• Replace damaged extension cords.

• When working outdoors, use only extension cords that are approved and correspondingly marked for

this application.

Information on recommended minimum conductor cross-sections and cable lengths is accessible via a link,

in the form of a QR code, at the end of this document.

5 Preparations at the workplace

CAUTION

Risk of injury! Inadvertent starting of the product.

▶Unplug the supply cord before making adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Accessory tool 3

For this product, use only Hilti chisels with the TE-H connection end.

Other chisels cannot be engaged correctly in the chuck and the yellow warning ring on the tool lock

remains visible. It indicates that the accessory tool is not suitable for the breaker!

▶Before each use, check that the yellow warning ring on the tool lock is no longer visible.

5.2 Inserting the accessory tool 4

Check the accessory tool for damage or uneven wear each time before use and replace it if necessary.

1. Apply a little grease to the connection end of the accessory tool.

2. Push the chisel with the TE-H connection end into the tool holder until it engages with an audible click

and the yellow warning ring is no longer visible.

3. Check that the chisel has engaged correctly by gripping and pulling it.

Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage

to the product.

8 English 2228669 *2228669*

5.3 Connecting the detachable supply cord 5

CAUTION

Risk of injury! Due to leakage current as a result of dirty contacts.

▶Connect the detachable electric connector to the electric tool only when it is clean and dry and when the

supply cord is unplugged from the power outlet.

1. Push the keyed, detachable electric plug connector into the socket as far as it will go, until it is heard to

engage.

2. Plug the supply cord into the power outlet.

Hilti recommends always leaving the detachable supply cord connected to the power tool. The

detachable supply cord should be disconnected only in the event of breakage/damage.

6 Operation

WARNING

Damaged power cords are a safety hazard! If the supply cord or extension cord is damaged while work

is in progress, immediately disconnect the device and the cord from the electricity supply. Do not touch the

damaged part of the cord.

▶Regularly check all supply cords. Replace defective extension cords. Have damaged power cords

replaced by a qualified specialist.

Use of a ground fault circuit interrupter (residual current device, RCD) with a maximum tripping current of

30 mA is recommended.

6.1 Starting breaker 6

1. Fully depress both the grip and the on/off switch at the same time.

▶The breaker starts.

2. Keep the on/off switch depressed while work is in progress.

▶In addition, you can control the performance of the machine by varying the extent to which the grip

is depressed.

If operation is paused for longer than 1 minute, the machine resets to its initial setting. To restart

the machine you have to fully depress both the grip and the on/off switch at the same time.

6.2 Chiseling 7

The chisel can be adjusted to 6 different positions (in 60° increments). This ensures that flat chisels

and shaped chisels can always be set to the optimum working position.

1. Plug the supply cord into the power outlet.

2. Bring the chisel into contact with the workpiece about 80 -100 mm (3¹⁄₈" - 4") from its edge.

3. Fully depress both the grip and the on/off switch.

4. Start with the chisel held at an angle of 90 ° to the concrete surface and face the chisel toward the edge

of the workpiece. Then change the angle to 70 ° to 80 ° and chisel the material away.

▶When working close to reinforcing bars, always guide the tip of the chisel toward the edge of the

workpiece, not toward a reinforcing bar.

Working at low temperatures:

The hammering mechanism works only when the power tool has reached a minimum operating

temperature. Bring the chisel into contact with the workpiece and allow the power tool to run

under no load until the required temperature is reached. If necessary, repeat this procedure until

the hammering mechanism begins to operate.

*2228669* 2228669 English 9

6.3 Removing the accessory tool 8

WARNING

Risk of injury! The accessory tool gets hot during use and may also have sharp edges.

▶Wear protective gloves when changing the tool.

1. Unplug the supply cord from the power outlet.

2. Pull the tool lock back as far as it will go.

3. Remove the accessory tool.

4. ATTENTION: Do not lay the hot accessory tool down on highly inflammable materials.

6.4 Disconnecting the detachable supply cord

1. Unplug the supply cord from the power outlet.

2. Press the release button and pull the keyed, detachable electric plug connector out of the socket.

3. Pull the supply cord connector out of the power tool.

Hilti recommends always leaving the detachable supply cord connected to the power tool. The

detachable supply cord should be disconnected only in the event of breakage/damage.

7 Care and maintenance

WARNING

Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet

can lead to severe injury and burns.

▶Always unplug the supply cord before carrying out care and maintenance tasks.

Care

• Carefully remove stubborn dirt from the tool.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

they can attack the plastic parts.

Maintenance

WARNING

Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including

burns.

▶Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical

specialists.

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

8 Transport and storage

Transport

▶Do not transport this product with an accessory tool installed.

▶Make sure that the equipment is held securely throughout all transport operations.

▶After transporting, always check all visible parts and controls for signs of damage and make sure that

they all function correctly.

Storage

▶Always store this product with the electric supply cable unplugged from the electricity supply.

10 English 2228669 *2228669*

▶Store this product in a dry place, where it cannot be accessed by children or unauthorized persons.

▶After a long period of storage, always check all visible parts and controls for signs of damage and make

sure that they all function correctly.

8.1 Transport using the transport trolley

WARNING

Risk of injury due to high weight The breaker is heavy.

▶Use the transport trolley whenever possible. If no transport trolley is available for use, the breaker should

always be transported by two persons.

Do not park the transport trolley on an incline.

Take care to ensure that the transport trolley stands in a steady, secure position.

Take care to use only safe transport routes.

1. Place the breaker on the locating pin on the transport trolley.

2. Secure the breaker during transport by closing the locking bar.

3. Push the chisel into the accessory tool holder until it engages.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The breaker doesn’t start. Electronics initialization in progress

(takes up to 4 seconds after plug-

ging in).

▶Switch the power tool off and

then on again.

Interruption in the electricity supply ▶Plug in another electric tool or

appliance and check whether it

works.

The electronic restart interlock is

activated after an interruption in

the electricity supply.

▶Switch the power tool off and

then on again.

Generator in sleep mode ▶Apply a load to the generator

by connecting a second power

consumer (e.g. worklight).

Switch the tool off and then on

again.

The detachable supply cord is not

plugged in correctly

▶Fit the detachable supply cord

to the power tool correctly.

The service indicator lights

red. The tool is faulty or servicing is due ▶Have the product repaired only

by Hilti Service.

Service indicator flashes red. Temporary fault ▶Wait 10 seconds for the flashing

to stop.

▶If the flashing does not stop

within 10 seconds, unplug the

supply cord from the power

supply and wait for 2 minutes.

▶If the flashing does not stop,

bring the product to Hilti

Service.

The voltage provided by the elec-

tric supply is too high.

▶Use a different power outlet.

Check the electric supply.

*2228669* 2228669 Français 11

Trouble or fault Possible cause Action to be taken

"Ready for operation" indica-

tor flashes green. Protection against overheating ▶Allow the product to cool down.

▶Clean the air vents. Running

under no load is still possible.

No hammering action. The power tool is too cold ▶Bring the tip of the accessory

tool into contact with the

working surface, switch the

power tool on and allow it to

run. If necessary, repeat the

procedure until the hammering

mechanism begins to operate.

Breaker hammers at severely

reduced frequency. No-contact stroke (chisel does not

impact on hard material)

▶Release the switch and restart

the machine, or:

▶With the switch pressed, also

fully depress the grip.

The breaker doesn’t start or

cuts out during operation. The extension cord is too long or

the conductor cross-section is

inadequate

▶Use an extension cord of an

approved length and / or of

adequate conductor cross-

section.

10 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances: qr.hilti.com/r11668382.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

12 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

Mode d'emploi original

1 Indications relatives au mode d'emploi

1.1 À propos de ce mode d'emploi

• Avant de mettre l'appareil en marche, lire impérativement ce mode d'emploi. C'est la condition

préalablement requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements du présent mode d'emploi ainsi que celles

figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement transmettre le produit à des

tiers accompagné de ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

12 Français 2228669 *2228669*

DANGER

DANGER !

▶Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

ATTENTION

ATTENTION !

▶Pour une situation potentiellement dangereuse pouvant entraîner des blessures corporelles ou des

dégâts matériels.

1.2.2 Symboles dans le manuel d'utilisation

Les symboles suivants sont utilisés dans le présent manuel d'utilisation :

Respecter le manuel d'utilisation

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du présent manuel d'utilisation.

La numérotation dans les illustrations indique les étapes de travail importantes ou les composants

importants pour les étapes de travail. Dans le texte, ces étapes de travail ou composants sont mis

en évidence avec les numéros correspondants, par ex. (3).

Les numéros de position sont utilisés dans l'illustration Vue d’ensemble et renvoient aux numé-

ros des légendes dans la section Vue d'ensemble du produit.

Ce signe doit inviter à manier le produit en faisant particulièrement attention.

1.3 Symboles sur le produit

1.3.1 Symboles sur le produit

Les symboles suivants peuvent être utilisés sur le produit :

Classe de protection II (double isolation)

Transport par pont roulant ou grue interdit

Transmission de données sans fil

1.4 Informations produit

Les produits sont destinés aux professionnels et ne doivent être utilisés, entretenus et réparés

que par un personnel autorisé et formé. Ce personnel doit être spécialement instruit quant aux dangers

inhérents à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont

utilisés de manière incorrecte par un personnel non qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque signalétique.

*2228669* 2228669 Français 13

▶Inscrivez le numéro de série dans le tableau suivant. Les informations produit vous seront demandées

lorsque vous contactez nos revendeurs ou services après-vente.

Caractéristiques produit

Burineur TE 3000AVR

Génération 03

N° de série

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit décrit ici est conforme aux

directives et normes en vigueur. Une copie de la Déclaration de conformité se trouve en fin de la présente

documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sécurité

2.1 Indications générales de sécurité pour les appareils électriques

AVERTISSEMENT Lire toutes les consignes de sécurité et instructions, illustrations et caractéris-

tiques techniques, qui accompagnent cet outil électroportatif. Tout manquement à l'observation des

instructions suivantes risque de provoquer une électrocution, un incendie et/ou de graves blessures.

Les consignes de sécurité et instructions doivent être intégralement conservées pour les utilisations

futures.

La notion d'« outil électroportatif » mentionnée dans les consignes de sécurité se rapporte à des outils

électriques raccordés au secteur (avec câble d'alimentation) et à des outils électriques sur accu (sans câble

d'alimentation).

Sécurité sur le lieu de travail

▶Conserver la zone de travail propre et bien éclairée. Un lieu de travail en désordre ou mal éclairé

augmente le risque d'accidents.

▶Ne pas faire fonctionner les outils électriques en atmosphère explosive et où se trouvent des

liquides, des gaz ou poussières inflammables. Les outils électriques produisent des étincelles qui

peuvent enflammer les poussières ou les fumées.

▶Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil électro-

portatif. En cas d'inattention il y a risque de perdre le contrôle de l'appareil.

Sécurité relative au système électrique

▶La fiche de secteur de l'outil électroportatif doit être adaptée à la prise de courant. Ne jamais

modifier la fiche de quelque façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils

électriques à branchement de terre. Des fiches non modifiées et des prises de courant adaptées

réduiront le risque de choc électrique.

▶Éviter le contact physique avec des surfaces mises à la terre tels que tuyaux, radiateurs, cuisinières

et réfrigérateurs. Il y a un risque élevé de choc électrique au cas où votre corps serait relié à la terre.

▶Ne pas exposer les outils électroportatifs à la pluie ou à l'humidité. La pénétration d'eau à l'intérieur

d'un outil électroportatif augmentera le risque d'un choc électrique.

▶Ne jamais utiliser le câble de raccordement à d'autres fins que celles prévues, telles que pour

porter, accrocher ou débrancher l'outil électroportatif de la prise de courant. Maintenir le câble

de raccordement à l'écart de la chaleur, des parties grasses, des bords tranchants ou des parties

en mouvement. Des câbles de raccordement endommagés ou emmêlés augmentent le risque de choc

électrique.

▶Si l'outil électroportatif est utilisé à l'extérieur, utiliser uniquement des câbles de rallonge

homologués pour les applications extérieures. L’utilisation d’un câble de rallonge homologué

pour les applications extérieures réduit le risque d’un choc électrique.

▶Si l'utilisation de l'outil électrique dans un environnement humide ne peut pas être évitée, utiliser

un interrupteur de protection contre les courants de court-circuit. L'utilisation d'un tel interrupteur

de protection réduit le risque d'une décharge électrique.

Sécurité des personnes

▶Rester vigilant, surveiller ce que l'on fait. Faire preuve de bon sens en utilisant l'outil électroportatif.

Ne pas utiliser l'outil électroportatif en étant fatigué ou sous l'emprise de l'alcool, de drogues ou

14 Français 2228669 *2228669*

de médicaments. Un moment d'inattention lors de l'utilisation de l'outil électroportatif peut entraîner

des blessures graves.

▶Utiliser un équipement de protection personnel et toujours porter une protection pour les

yeux. Les équipements de protection personnels tels que masque antipoussière, chaussures de

sécurité antidérapantes, casque de protection ou protection acoustique suivant l'utilisation de l'outil

électroportatif, réduiront le risque de blessures des personnes.

▶Éviter une mise en service par mégarde. S'assurer que l'outil électroportatif est arrêté avant de le

brancher à la source de courant et/ou à l'accu, de le prendre ou de le porter. Le fait de porter l'outil

électroportatif avec le doigt sur l'interrupteur ou de brancher l'appareil sur la source de courant lorsque

l'interrupteur est en position de fonctionnement peut entraîner des accidents.

▶Retirer tout outil de réglage ou toute clé avant de mettre l'outil électroportatif en fonctionnement.

Une clé ou un outil se trouvant sur une partie en rotation peut causer des blessures.

▶Adopter une bonne posture. Veiller à toujours garder une position stable et équilibrée. Cela permet

un meilleur contrôle de l'outil électroportatif dans des situations inattendues.

▶S'habiller de manière adaptée. Ne pas porter de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à distance des parties en mouvement. Des vêtements amples,

des bijoux ou des cheveux longs peuvent être happés par des parties en mouvement.

▶Si des dispositifs servant à aspirer ou à recueillir les poussières doivent être utilisés, s'assurer

qu'ils sont effectivement raccordés et correctement utilisés. L'utilisation d'un dispositif d'aspiration

de la poussière peut réduire les risques dus aux poussières.

▶Ne pas sous-estimer les mesures de sécurité à prendre et ne pas ignorer sciemment les règles

de sécurité applicables aux outils électriques, même si l'on est utilisateur chevronné après de

fréquentes utilisations de l'outil électroportatif. Un manque d'attention peut conduire à de graves

blessures en quelques fractions de seconde.

Utilisation et maniement de l'outil électroportatif

▶Ne pas forcer l'appareil. Utiliser l'outil électroportatif adapté au travail à effectuer. Un outil

électroportatif approprié réalisera mieux le travail et de manière plus sûre au régime pour lequel il a été

conçu.

▶Ne pas utiliser d'outil électroportatif dont l'interrupteur est défectueux. Tout outil électroportatif qui

ne peut plus être mis en ou hors fonctionnement est dangereux et doit être réparé.

▶Débrancher la fiche de la prise de courant et/ou l'accu amovible avant d'effectuer des réglages sur

l'appareil, de changer les accessoires, ou de ranger l'appareil. Cette mesure de précaution empêche

une mise en fonctionnement par mégarde de l'outil électroportatif.

▶Conserver les outils électroportatifs non utilisés hors de portée des enfants. Ne permettre

l'utilisation de l'appareil à aucune personne qui ne soit pas familiarisée avec celui-ci ou qui n'a

pas lu ces instructions. Les outils électroportatifs sont dangereux lorsqu'ils sont entre les mains de

personnes non initiées.

▶Prendre soin des outils électroportatifs et des accessoires. Vérifier que les parties en mouvement

fonctionnent correctement et qu'elles ne sont pas coincées, et contrôler si des parties sont

cassées ou endommagées de sorte que le bon fonctionnement de l'outil électroportatif s'en trouve

entravé. Faire réparer les parties endommagées avant d'utiliser l'appareil. De nombreux accidents

sont dus à des outils électroportatifs mal entretenus.

▶Garder les outils de coupe affûtés et propres. Des outils destinés à couper correctement entretenus

avec des arêtes de coupe tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler.

▶L'outil électroportatif, les accessoires, les outils amovibles, etc. doivent être utilisés conformément

à ces instructions. Tenir également compte des conditions de travail et du travail à réaliser.

L'utilisation des outils électroportatifs à d'autres fins que celles prévues peut entraîner des situations

dangereuses.

▶Veiller à ce que les poignées et surfaces de préhension soient toujours être sèches, propres et

exemptes de traces de graisse ou d'huile. Avec des poignées et surfaces de préhension glissantes, la

sécurité et le contrôle de l'outil électroportatif ne peuvent être assurés dans des situations inopinées.

Service

▶L'outil électroportatif doit uniquement être réparé par un personnel qualifié, utilisant exclusivement

des pièces de rechange d'origine. Ceci permet d'assurer la sécurité de l'outil électroportatif.

2.2 Indications générales de sécurité applicables aux burineurs

Consignes de sécurité pour tous les travaux

▶Porter un casque antibruit. Le bruit peut entraîner des pertes auditives.

▶Utiliser la poignée supplémentaire livrée avec l'appareil. La perte de contrôle peut entraîner des

blessures.

Leht laadib ...

Hilti TE 3000-AVR Kasutusjuhend

Hilti TE 3000-AVR Kasutusjuhend

teistes keeltes

Seotud paberid