Bestway Lay-Z-Spa Omaniku manuaal

EN

PT

ES

DE

FI

NL

IT

FR

EL

RU

PL

HU

SV

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS pg 003

PRE-SETUP CHECK LIST pg 013

INSTALLATION pg 015

SET-UP INSTRUCTION IN WINTER pg 015

USING THE SPA pg 019

MAINTENANCE pg 022

DISASSEMBLY AND STORAGE pg 024

TROUBLESHOOTING pg 026

ERROR CODES pg 027

EN

CONTENTS

VISIT BESTWAY YOUTUBE CHANNEL

FOR INSTRUCTION VIDEOS

PLEASE VISIT:

BESTWAYCORP.COM/SUPPORT

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

spare Parts, Please Visit

bestwaycorp.com/support

V

i

s

i

t

w

.

b

e

s

t

w

a

y

c

o

r

p

.

c

o

m

/

s

u

p

o

r

t

f

o

r

h

e

l

p

2

SAFETY INSTRUCTIONS

Carefully read, understand, and follow all information in this user

manual before installing and using the spa.

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW

ALL INSTRUCTIONS.

WARNING:

• The spa must be supplied through an isolating transformer or

supplied through a residual current device (RCD) having a rated

residual operating current not exceeding 30mA.

• The spa must be connected to a grounded mains supply socket

with a supply cord fitted with a plug and PRCD with a tripping

current of 10mA.

• The pump must be tested before each use, to test follow the

instruction of pump.

• If the supply cord is damaged, it must be replaced by the

manufacturer, service agent or similarly qualified persons in

order to avoid a hazard.

• To reduce the risk of electric shock, do not use extension cord to

connect unit to electric supply; provide a properly located outlet.

• No part of the appliance is to be located above the bath during

use.

• Parts containing live parts, except parts supplied with safety

extra-low voltage not exceeding 12V, must be inaccessible to a

person in spa pool; Parts incorporating electrical components,

except remote control devices, must be located or fixed so that

they cannot fall into the spa pool.

• The spa must be supplied by earthed power source.

• The power source on the wall of building should keep more than

4m away from pool.

• Warning: Always keep plug dry, plug in with wet plug is

definitely forbidden!

• The plug shall be directly connected only to a socket-outlet of

the fixed electrical installation.

• It is necessary to have the plug accessible after installation of

the spa.

CAUTION: In order to avoid a hazard due to inadvertent

IMPORTANT SAFETY INSTRUCTIONS

3

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a timer,

or connected to a circuit that is regularly switched on and off by

the utility.

After using your spa for 3-5 years, you should contact your local

qualified maintenance technician to ensure the safety and

performance of the spa. The main components, such as heating

element, air blower motor and non-return valves within the

electric unit should be checked and replaced (if necessary) by

professional persons.

• TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN

IT IS RAINING,THUNDERING OR LIGHTNING.

• Never wear your contact lenses when in your spa.

• Do not use spa during chemical maintenance.

• Extension cords can’t be used.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

- before cleaning or other maintenance

- if leave it unattended on holidays

• When the appliance will be not used for a long time, such as in

the winter, the spa or pool set should be disassembled and

stored indoor.

• For safety reason, only use the accessories provided or

approved by the spa manufacturer.

• Do not to place the spa on slippery surface , and to make sure

the surface is free of sharp object before installation.

• Never place any electrical supplies or appliance, such as a light,

telephone, radio, or television, within 2m of spa.

• Caution: Read the instruction before using the appliance and

installation or reassemble every time.

• Safekeeping the instruction. If instruction is missed, please

contact with manufacturer or search it in website

www.bestwaycorp.com

• Warning: For electric safety, a PRCD is incorporated in the

power cord, if the leakage current is detected more than

10mA, the device will operate and cut-off the power supply,

in such case, please unplug and stop using the spa at once.

Don’t reset the product by yourself. And you must contact

4

the local service agent to check and repair the product.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. (For EU market)

• Cleaning and user maintenance must be performed by an adult

above18 years old who is familiar with the risk of electric shock.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

(For market other than EU)

• Water attracts children; always attach a spa cover after each

use.

• Do not bury cord. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• DANGER - Risk of Accidental Drowning (especially children

under 5 years). Caution shall be exercised to prevent

unauthorized access to the spa by children. This can be reached

by adult supervisor securing the means of access or installing a

safety protection device to the spa. To avoid accidents during

spa use, ensure that children are kept under constant adult

supervision.

• DANGER - Risk of Injury. The suction fittings in this spa are

sized to match the specific water flow created by the pump.

Should the need arise to replace the suction fittings or the pump,

be sure that the flow rates are compatible. Never operate the

spa if the suction fittings are broken or missing. Never replace a

suction fitting with one rated less than the flow rate marked on

the original suction fitting.

• RISK OF INJURY. Never operate spa if inlet / outlet pipes are

broken or missing. Never attempt to replace the inlet / outlet

pipes. Always consult your local Aftersales centre.

• RISK OF ELECTRIC SHOCK. Install at least 2m from all metal

5

surfaces.

• RISK OF ELECTRIC SHOCK. Never operate any electrical

appliance when in your spa or when your body is wet. Never

place any electric appliance, such as a light, telephone, radio, or

television, within 2m of spa.

• Consider that the comfortable temperature range during use

may be lower than the maximum safe temperature.

• During pregnancy, soaking in hot water may cause damage to

the fetus. Limit use to 10 minutes at a time.

• TO REDUCE THE RISK OF INJURY:

A. The water in a spa should never exceed 40°C (104°F). Water

temperature between 38°C (100°F) and 40°C (104°F) is

considered safe and comfortable for a healthy adult. Lower

water temperatures are recommended for young children and

when spa use exceeds 10 minutes.

B. Since excessive water temperatures have a high potential for

causing fetal damage during the early months of pregnancy,

pregnant or possibly pregnant women should limit spa water

temperature to 38°C (100°F).

C. Before entering a spa, the user should measure the water

temperature with an accurate thermometer since the

tolerance of water temperature regulating device varies.

D. The use of alcohol, drugs, or medication before or during spa

use may lead to unconsciousness with the possibility of

drowning.

E. Obese persons and persons with a history of heart disease,

low or high blood pressure, circulatory system problems, or

diabetes should consult a physician before using a spa.

F. Persons using medication should consult a physician before

using a spa since some medication may induce drowsiness

while other medication may affect heart rate, blood pressure,

and circulation.

G. Avoid putting the head under water at all times.

H. Avoid swallowing spa water.

• TO REDUCE THE RISK OF INJURY: Never pour water with a

temperature higher than 40°C (104°F) into the spa pool directly.

• The use of alcohol, drugs, or medication can greatly increase the

risk of fatal hyperthermia. Hyperthermia occurs when the

6

internal temperature of the body reaches a level that is several

degrees above the normal body temperature of 37°C (98.6°F).

The symptoms of hyperthermia include an increase in the

internal temperature of the body, dizziness, lethargy,

drowsiness, and fainting. The effects of hyperthermia include

failure to perceive heat; failure to recognize the need to exit spa

or hot tub; unawareness of impending hazard; fetal damage in

pregnant women; physical inability to exit the spa or hot tub; and

unconsciousness resulting in the danger of drowning.

• Electric installations should follow national wiring rules, consult a

qualified electrician with any questions.

• These warnings, instructions, and safety guidelines address

some common risks of water recreation, but they cannot cover

all risks and dangers in all cases. Always use caution, common

sense, and good judgment when enjoying any water activity.

Retain this information for future use. In addition, the following

information can be supplied depending on the spa type:

Non Swimmers safety

- Continuous, active, and vigilant supervision of weak swimmers

and non-swimmers especially in exercise spas, by a

competent adult is required at all times (remembering that

children under five years of age are at the highest risk of

drowning).

- Designate a competent adult to supervise the spa each time it

is being used.

- Weak swimmers or non-swimmers should wear personal

protection equipment, especially when using the exercise spa.

- When the spa is not in use, or unsupervised, remove all toys

from the spa and its surrounding area to avoid attracting

children to the spa.

Safety devices

- A safety cover or other safety protection device shall be used,

or all doors and windows (where applicable) shall be secured

to prevent unauthorized access to the spa.

- Barriers, covers, alarms, or similar safety devices are helpful

aids, but they are not substitutes for continuous and competent

adult supervision.

Safety equipment

7

- It is recommended to keep rescue equipment (e.g. a ring buoy)

by the spa (if appropriate).

- Keep a working phone and a list of emergency phone numbers

near the spa.

Safe use of the spa

- Encourage all users especially children to learn how to swim.

- Learn Basic Life Support (Cardiopulmonary Resuscitation -

CPR) and refresh this knowledge regularly. This can make a

life-saving difference in the event of an emergency.

- Instruct all spa users, including children, what to do in case of

an emergency.

- Never dive into any shallow body of water. This can lead to

serious injury or death.

- Do not use the spa when using alcohol or medication that may

impair the bather's ability to safely use the spa.

- When covers are used, remove them completely from the

water surface before entering the spa.

- Protect spa occupants from water related illnesses by advising

them to keep water treated and practicing good hygiene.

Consult the water treatment guidelines in the user's manual.

- Store chemicals out of the reach of children.

- Use the signage provided on the spa or within 2 000 mm of the

spa in a prominent visible position.

- Removable ladders, when removed, shall be stored safely

where children cannot climb on it.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.

CAUTION:

• We strongly recommend not to unfold and inflate the spa if the

ambient temperature is below 15°C(59°F). We suggest inflating

the spa indoors, and then continuing set up outdoors. If the

outdoor temperature is lower than 6°C(42.8°F), the spa heater

must always be on. In this mode, the Freeze Shield™ system

can keep the internal temperature between 6°C(42.8°F) and

10°C(50°F) to prevent damage, such as water freezing in the

pipes or the circulation system.

Important:

If the Freeze Shield™ system isn’t working, alarms

will pop up on the spa. Be sure to check the status of your spa

if the outdoor temperature is below 6°C(42.8°F). In case of a

8

long-term absence from home when there is a risk of

temperatures falling below 6°C(42.8°F), we strongly suggest

disassembling the spa and storing it following the storage

procedure.

• Do not use the spa alone.

• People with infectious diseases should not use a spa.

• Do not use the spa immediately following strenuous exercise.

• Always enter and exit the spa slowly and cautiously. Wet

surfaces are slippery.

• To avoid damage to the pump, the spa must never be operated

unless the spa is filled with water.

• Immediately leave spa if the user feels uncomfortable or

sleepy.

• Whenever the spa is emptied, the filter should be cleaned (and

drained/dried,where applicable).

• Any manual dosing of chemicals shall not be performed while

bathers are present in the spa.

• Never add water to chemicals. Always add chemicals to water

to avoid strong fumes or violent reactions that may result in

hazardous chemical spray.

• Regarding the information pertaining to cleaning, maintenance

of water, and disposal of water, please see section

"MAINTENANCE".

• Regarding the information pertaining to the installation, thanks

to refer to the below paragraph of the manual.

NOTE:

• Please examine equipment before use. Notify Bestway at the

customer service address listed on this manual for any

damaged or missing parts at the time of purchase. Verify that

the equipment components represent the models that you had

intended to purchase.

• This product is not intended for commercial use.

SAVE THESE INSTRUCTIONS

SELECTED LOCATION

Indoor and outdoor & above ground & portable wiring &

9

portable spa

WARNING: The selected location has to be able to support

of supporting the expected load.

WARNING: An adequate drainage system has to be provided

to deal with overflow water for both indoor and outdoor

installations.

• Always keep the spa cover on to minimize heat loss during

heating of the spa between uses (but not while it is being

used). Ensure the cover is fitted tightly, as per instructions

to maximize insulation. It shall be recommended that the

cover, when not in use, should be kept off the ground to

retain its cleanliness (particularly the surface in close

proximity to the water spa water surface). The cover should

be stored in an appropriate location, where it cannot be

damaged, or cause damage.

• Check the set water temperature and consider lowering it

for the times when the spa will typically not be in use.

• Depending on external conditions, consider turning off the

heater entirely if not using the spa for an extended period of

time (where the spa provides this option, but still maintains

residual disinfection/pH-values).

• It is recommended to use an insulating ground cloth

underneath the spa to minimize heat loss through the

bottom of the spa.

• Maintain clean filters to preserve appropriate working

conditions for the pump and avoid unnecessary water

replacement and re-heating.

• Keep the spa away from the rest area to minimize noise

disturbance.

• Recommended to ask a qualified contractor or a structural

engineer to verify if the support material is strong enough to

support the maximum design load of the spa, spa water

and bathers. Read the filled weight information on the

package.

• Please keep at least 1m clearance around the spa.

• Consult your local government authority for water

regulations related to convenient water supply for filling the

spa.

10

• Recommended to consult experts and/or local authorities to

apply local or national laws/regulations relating to childproof

fencing, safety barriers, lighting, and other safety

requirements.

• Do not put the cover on the ground or any other dirty

surface when not in place on the spa.

• When the spa is being used, the cover should be placed in

a clean, dry area, otherwise it can pick up dirt and bacteria.

Covers should not be put on wooden tables or wooden

decking because of the risk of bleaching the wood. A cover

lifter, or similar device, is useful for ensuring that the cover

does not come into contact with the ground. A cover lifter is

strongly recommended for spas in rental settings.

IMPORTANT: Because of the combined weight of the

Lay-Z-Spa, water, and users, it is extremely important that

the base where the Lay-Z-Spa is installed is smooth, flat,

level and capable of uniformly supporting the weight for the

entire time the Lay-Z-Spa is installed (not on the carpet or

other similar material). If the Lay-Z-Spa is placed on a

surface, which does not meet these requirements, any

damage caused by improper support is not covered under

the manufacturer’s warranty. It is the responsibility of the

Lay-Z-Spa owner to assure the integrity of the site at all

times.

1. Indoor Installation:

Be aware of special requirements if you install the spa

indoors.

• Humidity is a natural side effect with Lay-Z-Spa installation.

Determine the effects of airborne moisture on exposed

wood, paper, etc. in the proposed location. To minimize

these effects it is best to provide plenty of ventilation to the

selected area. An architect can help determine if more

ventilation is needed.

• Consult your local government authority for installation

regulations.

• Keep suitable air treatment in the spa chamber (ventilation

and dehumidification) regularly to preserve the bathers’

safety and comfort .

11

• Do not to install the spa on carpet or other floor materials

(e.g. untreated cork, timber or other porous materials) that

promote or harbour moisture and bacteria, or that could be

affected by water treatment chemicals used in the spa.

• Empty the spa before remove it from the chamber or

building.

2. Outdoor Installation:

• During filling, draining or when in use, water may flow out of

the spa. Therefore the Lay-Z-Spa should be installed near a

floor drain.

• Do not leave the spa's surface exposed to direct sunlight for

long periods of time.

• Consult your local professional installers for environmental

conditions, such as ground water and risk of frost.

• Recommended to protecting the spa from direct sunlight

exposure by a cover when not in use.

PRCD WARNING

WARNING: Before inserting plug into a power outlet, make

sure the current rate of the power outlet is suitable for the

pump.

WARNING: Using an extension lead or multi plug adaptor

with the spa heater can cause the plug to overheat, causing

damage to the equipment and surrounding items. The spa is

a class I electrical appliance and must be connected directly

to a grounded socket. It is recommended to only use a

socket which is resistant to humidity and capable of high

power loading. Regularly check the plug and socket for signs

of damage before using the spa – do not use the spa if the

plug or socket is damaged. If you are unsure about the

quality of the electrical supply, please consult a qualified

electrician before use.

WARNING: The PRCD plug must be tested before each use

to avoid risk of electric shock.

WARNING: Do not use the pump if this test fails. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

12

PARTS CHECKS

Please examine equipment before use.

Notify Bestway® customer service of any

damaged or missing parts at the time of

purchase. Verify that the equipment

components represent the model that you

had intended to purchase. For reference

please use the diagrams below.

PRE-SETUP CHECK LIST

HAWAII HYDROJET PRO

S200102 (

60031)

— 1.80 m x 1.80 m x 71 cm / 71" x 71" x 28"

04

P04125

1

10

P05347

1

16

P61727ASS18

1

06

P05343

1

12

P00820

1

03

P05277

1

09

P6575ASS16

2

15

P61726ASS18

1

01

P05274

1

07

/

2

13

P05320

8

02 P05504(EU)/

P05507(NL)/

P05530(NO) 1

08

P05345

1

14

P05525

2

05

P05341

1

11

P00217

1

17

P05528

818

P05346

1

19

P05526

120

P05767

1

4 - 6 1.5-2ºC/h

3-4ºF/h

1,325 L/h

350 gal/h

1.2PSI

0.08Bar

795 L

210 gal

848 kg

1,869 Lb

13

MALDIVES HYDROJET PRO

S200102 (

60033)

— 2.01 m x 2.01 m x 80 cm / 79" x 79" x 31.5"

04

54173GASS18

1

10

P05347

1

06

P05343

1

12

P00820

1

03

P05283

1

09

P6575ASS16

2

15

P61726ASS18

1

01

P05280

1

07

/

2

13

P05320

8

02 P05504(EU)/

P05507(NL)/

P05530(NO)

1

08

P05345

1

14

P05525

2

05

P05503

1

11

P00217

1

16

58471

217

P61750ASS18

2

22

P05526

120

F6A526-02ASS18

6

18

F4C009B-02ASS17

5

23

P61727ASS18

119

P05528

8 24

P05767

121

P05346

1

5 - 7 1-1.5ºC/h

2-3ºF/h

1,325 L/h

350 gal/h

1.2PSI

0.08Bar

1,050 L

277 gal

1,118 kg

2,465 Lb

SANTORINI HYDROJET PRO

S200102 (

60075)

— 2.16 m x 80 cm / 85" x 31.5"

04

54175GASS18

1

10

P05347

1

06

P05343

1

12

P00820

1

03

P06277

1

09

P6575ASS16

2

15

P61726ASS18

1

01

P06274

1

07

/

2

13

P05320

8

02 P05504(EU)/

P05507(NL)/

P05530(NO)

1

08

P05345

1

14

P05525

2

05

P05503

1

11

P00217

1

16

58471

2

20

P05526

121

P61727ASS18

122

P05767

119

P05346

1

18

P05528

10

23

P06279

5

17

F4C009B-02ASS17

1

5 - 7 1-1.5ºC/h

2-3ºF/h

1,325 L/h

350 gal/h

1.2PSI

0.08Bar

1,190 L

314 gal

1,253 kg

2,762 Lb

2

14

123

INSTALLATION

It is important to follow these suggestions if you are setting up the spa during the winter

period. This will prevent damage to the PVC material and extend the life of your product

drastically.

•

If the ambient temperature is below 10°C(50°F), we suggest keeping the package

indoor where the temperature is above 15°C(59°F) for at least 2h before inflation. This

will make the spa liner more flexible and easier to set up.

•

Open the package in the same room where the temperature is above 15°C(59°F), and

inflate the spa using the spa heater.

•

Position the spa liner outdoor in the desired position, connect the spa heater and fill

with water.

Important: The water temperature used to fill the spa must be above 6°C(42.8°F),

otherwise when you begin to operate with the spa heater, the E03 alarm will appear.

Important: If the Freeze Shield™ system isn’t working, alarms will pop up on the spa.

Be sure to check the status of your spa if the outdoor temperature is below 6°C(42.8°F).

In case of a long-term absence from home when there is a risk of temperatures falling

below 6°C(42.8°F), we strongly suggest disassembling the spa and storing it following

the storage procedure. When you assemble the spa, the automatic warm function will

turn on. In this condition, the spa can be used when the temperature is lower than

6°C(42.8°F).

< 10°C(50°F)

> 15°C(59°F)

SET-UP

INSTRUCTION

IN WINTER

15

6

4

3-6 min.

A

B

C

MALDIVES SANTORINI

5.2

5.1.1 5.1.2

16

78

11.1 11.2

SANTORINI

MAX.

MIN.

910

17

RESET

TEST

2

RESET

TEST

4

RESET

TEST

1

3

RESET

TEST

PRCD TEST

SPA PUMP EQUIPOTENTIAL BONDING TERMINAL

It is recommended to arrange for a qualified electrician to connect

the spa pump to an equipotential bonding terminal using a

minimum 2.5mm

2

solid copper conductor.

When inflating, you will notice that air will be expelled

from the area where the air hose connects to the

pump, this is normal for technique requirements.

Important: Don't cover the holes on the base of the

inflation hose. This operation will over inflate the liner

and damage the structure.

Do not use an air compressor to inflate the pool.

Do not drag the pool on rough ground as this may cause damage to the pool liner.

Inflation time for reference only.

18

A. LOCK/UNLOCK BUTTON: The pump has a 5-minute auto-lock, this

light will turn on. To lock or unlock the pump, place a finger over the

lock/unlock button for 3 seconds.

B. POWER-SAVING TIMER BUTTON: Designed to help avoid wasting

power by setting the time and duration of the heating cycle for the spa.

This way, you can enjoy your spa at the time you desire, without needing

to leave the heater on at all times.

A

B

A

C

B

D

CK

B

UT

TO

N

T

he

p

m

p

ha

B

C

D

E

G

I

5

i

t

h

J

F

J

E

G

I

F

H+

-

Adjustment

of Jet Nozzle

STEP 1: Set the heating duration

1. Press the button unit the LED starts to flash.

2. Press the or button to adjust the heating duration (From 1-999 hours).

3. Press the button again to confirm the heating duration.

STEP 2: Set the number of hours FROM NOW when the heater will activate

1. After setting the heating duration, the LED starts to flash.

2. Press the or button to adjust the hours until time of activation (From 0-999 hours).

3. Press button again or simply touch nothing for 10 seconds to confirm the setting. The

LED will light steadily, and the countdown to heater activation will begin.

To modify the timer settings: Press the button and use the or button to adjust.

Cancel the setting: Press the button for 2 seconds.

NOTE: After setting, the screen flashes the current temperature and time alternately.

NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 999 hours;

Reservation time adjustment (the number of hours FROM NOW when the heater will begin to

function) may be set from 0 to 999 hours. If the timer is set at 0 hour, the heating system will

activate immediately.

Note that the timer is one time per use - the user sets the duration of the heating cycle, and

how many hours from now the heating cycle begins. The timer does NOT repeat until reset.

C. HEAT BUTTON: Use this button to activate the heating system. When

the light above the heat button is red, the heating system is activated.

When the light is green, the water is at the set temperature and the

heating system is at rest.

NOTE: If the heating system is activated the filtration system will

automatically start.

NOTE: After turning off the heating system the filtration system will

continue to operate.

NOTE: If the spa heater is on when the water temperature is below

6ºC(42.8°F), the heating system will warm the water until 10ºC(50°F)

automatically.

D. MASSAGE SYSTEM BUTTON: Use this button to activate the

massage system, which has a 30-minute auto-shutoff feature. The light

above the Massage System Button displays red when activated.

IMPORTANT: Do not run the Massage system when the cover is

USING THE SPA

19

NOTE: The WATER HEATER rate may change in the conditions below:

• When the outdoor temperature is below 15°C (59°F).

• If the cover is not in position when the heating function is activated.

NOTE: To display the current water temperature, run the filter system for at least a minute.

The water temperature as tested by an external thermometer may vary from the

temperature as displayed on the spa panel by as much as approximately 2°C.

POWER-SAVING TIMER LED:

This flashing LED means you are setting the heating duration. The light will

be on when the heating function starts to work.

This flashing LED means you are setting the number of hours FROM NOW

when the heater will activate. When the light is on, the Power-Saving

Timer function is set.

J. HYDROJET SYSTEM BUTTON: This button turns the water pump on

and off. The light above the HydroJet system button displays red when

activated.

NOTE: The system will shut off automatically after 1 hour.

NOTE: Do not dry run the HydroJet System.

attached. Air can accumulate inside the spa and cause irreparable

damage to the cover and bodily harm.

NOTE: Heat and massage system work together to create a warm

massage experience.

E/G. TEMPERATURE ADJUSTMENT BUTTONS: Pressing the

Temperature Increase or Decrease buttons will cause the LED to flash.

When it is flashing you can adjust to the desired temperature setting. If

you hold these buttons down the values will rapidly increase or decrease.

The new and desired temperature setting will remain on the LED display

for 3 seconds to confirm the new value.

NOTE: The default temperature is 35°C (95°F).

NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C

(104°F).

F. ON/OFF BUTTON: Press this button for 2 seconds to active the control

panel buttons and the light turns to green. Press this button for 2 seconds

to turn off all currently activated functions.

H. CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed

in either Fahrenheit or Celsius.

I. WATER FILTER BUTTON: This button turns the filter pump on and off.

The light above the Water Filter Button displays red when activated.

WINTER USE INSTRUCTIONS

20

Leht laadib ...

Bestway Lay-Z-Spa Omaniku manuaal

Bestway Lay-Z-Spa Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid