Sanyo SAP-KRV123EH Technical & Service Manual

TECHNICAL & SERVICE MANUAL

SAP-KRV93EH + SAP-CRV93EHN

SAP-KRV123EH + SAP-CRV123EHN

DC INVERTER SPLIT SYSTEM AIR CONDITIONER

SAP-CRV93EHN

SAP-CRV123EHN

AIR CO

N

DITIONER

IMPORTANT

These air conditioners employ new

refrigerant R410A.

Pay special attention when

servicing the unit.

SAP-KRV93EH

SAP-KRV123EH

FILE NO.

REFERENCE NO. SM700598-01

Indoor Unit Outdoor Unit

Indoor Model No. Product Code No.

SAP-KRV93EH 1 852 089 81

SAP-KRV123EH 1 852 089 80

Outdoor Model No. Product Code No.

SAP-CRV93EHN 1 852 094 27

SAP-CRV123EHN 1 852 094 26

Destination: Nothen Europe

(Norway / Sweden / Finland / Denmark)

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

2

IMPORTANT!

Please Read Before Starting

This air conditioning system meets strict safety and oper-

ating standards. As the installer or service person, it is an

important part of your job to install or service the system

so it operates safely and efficiently.

For safe installation and trouble-free operation, you

must:

●

Carefully read this instruction booklet before beginning.

●

Follow each installation or repair step exactly as

shown.

●

Observe all local, state, and national electrical codes.

●

Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a haz-

ard or unsafe practice which

can result in severe personal

injury or death.

This symbol refers to a hazard

or unsafe practice which can

result in personal injury or

product or property damage.

If Necessary, Get Help

These instructions are all you need for most installation

sites and maintenance conditions. If you require help for

a special problem, contact our sales/service outlet or

your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for

improper installation or maintenance service, including

failure to follow the instructions in this document.

SPECIAL PRECAUTIONS

When Wiring

ELECTRICAL SHOCK CAN CAUSE SEVERE PER-

SONAL INJURY OR DEATH. ONLY A

QUALIFIED, EXPERIENCED ELECTRI-

CIAN SHOULD ATTEMPT TO WIRE THIS

SYSTEM.

• Do not supply power to the unit until all wiring and tub-

ing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this

system. Carefully refer to the wiring diagram and

these instructions when wiring. Improper connections

and inadequate grounding can cause accidental

injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause

overheating at connection points and a possible fire

hazard.

When Transporting

Be careful when picking up and moving the indoor and

outdoor units. Get a partner to help, and bend your

knees when lifting to reduce strain on your back. Sharp

edges or thin aluminum fins on the air conditioner can

cut your fingers.

When Installing…

…In a Ceiling or Wall

Make sure the ceiling/wall is strong enough to hold the

unit’s weight. It may be necessary to construct a strong

wood or metal frame to provide added support.

…In a Room

Properly insulate any tubing run inside a room to prevent

“sweating” that can cause dripping and water damage to

walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to provide

a solid, level foundation for the outdoor unit. This pre-

vents water damage and abnormal vibration.

…In an Area with High Winds

Securely anchor the outdoor unit down with bolts and a

metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is higher

than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of

the flare and union tubes before connecting them,

then tighten the nut with a torque wrench for a leak-

free connection.

• Check carefully for leaks before starting the test run.

When Servicing

• Turn the power OFF at the main power box (mains)

before opening the unit to check or repair electrical

parts and wiring.

• Keep your fingers and clothing away from any moving

parts.

• Clean up the site after you finish, remembering to

check that no metal scraps or bits of wiring have been

left inside the unit being serviced.

Others

• Ventilate any enclosed areas when installing or testing

the refrigeration system. Escaped refrigerant gas, on

contact with fire or heat, can produce dangerously

toxic gas.

• Confirm upon completing installation that no refriger-

ant gas is leaking. If escaped gas comes in contact

with a stove, gas water heater, electric room heater or

other heat source, it can produce dangerously toxic

gas.

WARNING

CAUTION

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

3

Table of Contents

Page

1. OPERATING RANGE................................................................................................................ 4

2. SPECIFICATIONS

2-1. Unit Specifications............................................................................................................ 5

2-2. Major Component Specifications...................................................................................... 7

2-3. Other Component Specifications...................................................................................... 11

3. DIMENSIONAL DATA................................................................................................................ 12

4. REFRIGERANT FLOW DIAGRAM

4-1. Refrigerant Flow Diagram................................................................................................. 14

5. PERFORMANCE DATA

5-1. Temperature Charts..........................................................................................................15

5-2. Air Throw Distance Charts ............................................................................................... 17

5-3. Operating Frequency Charts............................................................................................ 19

6. ELECTRICAL DATA

6-1. Electrical Characteristics..................................................................................................23

6-2. Electric Wiring Diagrams.................................................................................................. 24

7. INSTALLATION INSTRUCTIONS

7-1. Installation Site Selection .................................................................................................26

7-2. Recommended Wire Length and Diameter...................................................................... 28

7-3. Remote Control Unit Installation Position......................................................................... 29

7-4. How to Test Run the Air Conditioner ................................................................................ 30

7-5. Remove the Grille to Install the Indoor Unit...................................................................... 31

8. MAINTENANCE

8-1. Address Setting of the Remote Control Unit .................................................................... 32

8-2. Disconnecting and Connecting Positive Connector for Outdoor Unit ............................... 33

9. FUNCTIONS

9-1. Operation Functions.........................................................................................................34

9-2. Protective Functions......................................................................................................... 36

10. TROUBLESHOOTING............................................................................................................... 38

11. CHECKING ELECTRICAL COMPONENTS

11-1. Measurement of Insulation Resistance ............................................................................ 43

11-2. Checking Continuity of Fuse on PCB Ass’y...................................................................... 44

12. REFRIGERANT R410A:

SPECIAL PRECAUTIONS WHEN SERVICING UNIT............................................................... 45

INSTRUCTION MANUAL....................................................................................... 52

APPENDIX

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

4

1. OPERATING RANGE

Temperature Indoor Air Intake Temp. Outdoor Air Intake Temp.

Cooling

Maximum 32°C D.B. / 23°C W.B. 43°C D.B.

Minimum 19°C D.B. / 14°C W.B. 19°C D.B.

Heating

Maximum 27°C D.B. 24°C D.B. / 18°C W.B.

Minimum 16°C D.B. –20°C D.B. / –20°C W.B.

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

5

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Heating: Indoor air temperature 20°C D.B.

Outdoor air temperature 7°C D.B. / 6°C W.B.

2. SPECIFICATIONS

2-1. Unit Specifications

Indoor Unit SAP-KRV93EH

Outdoor Unit SAP-CRV93EHN

Power Source 220 – 240V Single-phase 50Hz

Performance Cooling Heating

Capacity kW 2.65 (0.9 – 3.2) 3.60 (0.9 – 5.0)

BTU/h 9,000 (3,100 – 10,900) 12,300 (3,100 – 17,100)

Air circulation (High) m

3

/h 480 530

Moisture removal (High) Liters/h 1.6 —

Electrical Rating Cooling Heating

Available voltage range V 198 – 264

Running amperes A 3.86 (1.28 – 5.88) 4.81 (1.21 – 6.47)

Power input W 755 (250 – 1,150) 995 (250 – 1,515)

Power factor % 85 90

C.O.P. W/W 3.51 3.62

Compressor locked rotor amperes A 15

Features

Controls / Temperature control Microprocessor / I.C. thermistor

Control unit Wireless remote control unit

Timer ON / OFF 24 hours & Daily program, 1-hour OFF

Fan speeds Indoor / Outdoor 3 and Auto / 1 (Hi)

Airflow direction (Indoor) Horizontal Manual

Vertical Auto

Air filter Washable, Anti-Mold

Compressor Rotary (DC inverter)

Refrigerant / Amount charged at shipment g R410A / 950

Refrigerant control Electric expansion valve

Operation sound Indoor: Hi/Me/Lo/Qt* dB-A 34 / 31 / 28 / 23 34 / 31 / 28 / 23

(*Qt=Quiet mode) Outdoor: Hi dB-A 46 47

Refrigerant tubing connections Flare type

Max allowable tubing length at shipment m 7.5

Refrigerant Narrow tube mm (in.) 6.35 (1/4)

tube diameter Wide tube mm (in.) 9.52 (3/8)

Refrigerant tube kit / Accessories Optional / Air clean filter

Voltage Rating 230V

Dimensions & Weight Indoor Unit Outdoor Unit

Unit dimensions Height mm 285 548

Width mm 825 720

Depth mm 189 265

Package dimensions Height mm 350 600

Width mm 900 856

Depth mm 255 362

Weight Net kg 9.0 34.0

Shipping kg 11.0 36.0

Shipping volume m

3

0.080 0.186

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

6

Indoor Unit SAP-KRV123EH

Outdoor Unit SAP-CRV123EHN

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Heating: Indoor air temperature 20°C D.B.

Outdoor air temperature 7°C D.B. / 6°C W.B.

Power Source 220 – 240V Single-phase 50Hz

Performance Cooling Heating

Capacity kW 3.50 (0.9 – 3.8) 4.20 (0.9 – 5.8)

BTU/h 11,900 (3,100 – 13,000) 14,300 (3,100 – 19,800)

Air circulation (High) m

3

/h 500 530

Moisture removal (High) Liters/h 2.0 —

Electrical Rating Cooling Heating

Available voltage range V 198 – 264

Running amperes A 5.21 (1.19 – 6.21) 5.48 (1.18 – 7.09)

Power input W 1,090 (250 – 1,300) 1,165 (250 – 1,690)

Power factor % 91 92

C.O.P. W/W 3.21 3.61

Compressor locked rotor amperes A 15

Features

Controls / Temperature control Microprocessor / I.C. thermostat

Control unit Wireless remote control unit

Timer ON / OFF 24 hours & Daily program, 1-hour OFF

Fan speeds Indoor / Outdoor 3 and Auto / 1 (Hi)

Airflow direction (Indoor) Horizontal Manual

Vertical Auto

Air filter Washable, Anti-Mold

Compressor Rotary (DC inverter)

Refrigerant / Amount charged at shipment g R410A / 1,100

Refrigerant control Electric expansion valve

Operation sound Indoor: Hi/Me/Lo/Qt* dB-A 36 / 33 / 29 / 25 34 / 31 / 29 / 25

(*Qt=Quiet mode) Outdoor: Hi dB-A 47 49

Refrigerant tubing connections Flare type

Max allowable tubing length at shipment m 7.5

Refrigerant Narrow tube mm (in.) 6.35 (1/4)

tube diameter Wide tube mm (in.) 9.52 (3/8)

Refrigerant tube kit / Accessories Optional / Air clean filter

Voltage Rating 230V

Dimensions & Weight Indoor Unit Outdoor Unit

Unit dimensions Height mm 285 548

Width mm 825 720

Depth mm 189 265

Package dimensions Height mm 350 600

Width mm 900 856

Depth mm 255 362

Weight Net kg 9.0 35.0

Shipping kg 11.0 37.0

Shipping volume m

3

0.080 0.186

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

7

2-2. Major Component Specifications

2-2-1. Indoor Unit

Indoor Unit SAP–KRV93EH

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Control PCB

Part No. CB-KRV93EH (POW-KRV93GJH)

Controls Microprocessor

Control circuit fuse 250V 3.15A

Flap Motor and Louver Motor

Type Stepping motor

Model MP24Z3-12V

Rating DC 12V

Coil resistance (Ambient temp. 25°C) Ω Each pair of terminals: 400 ± 7%

Heat Exchanger Coil

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.3

Face area m

2

0.188

Fan & Fan Motor

Type Fan / Fan motor Cross-flow / AC motor

Q’ty … Dia. and length mm 1 … D92 / L634

Fan motor model … Q’ty IBH-884-066 … 1

No. of poles … Rough measure rpm (Cool / Heat) 4 … 1,200 / 1,250

Nominal output W 30

Coil resistance (Ambient temp. 20°C) Ω BRN – WHT: 234

PNK (RED) – WHT: 209

— : —

Safety devices Type Thermal fuse

Operating temp. Open °C 130

Close Automatic reclosing

Run capacitor µF 1.2

VAC 440

Remote Control Unit RCS-3HVPSS4E

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

8

Indoor Unit SAP–KRV123EH

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Control PCB

Part No. CB-KRV123EH (POW-KRV93GJH)

Controls Microprocessor

Control circuit fuse 250V 3.15A

Flap Motor and Louver Motor

Type Stepping motor

Model MP24Z3-12V

Rating DC 12V

Coil resistance (Ambient temp. 25°C) Ω Each pair of terminals: 400 ± 7%

Heat Exchanger Coil

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.3

Face area m

2

0.188

Fan & Fan Motor

Type Fan / Fan motor Cross-flow / AC motor

Q’ty … Dia. and length mm 1 … D92 / L634

Fan motor model … Q’ty IBH-884-066 … 1

No. of poles … Rough measure rpm (Cool / Heat) 4 … 1,250 / 1,250

Nominal output W 30

Coil resistance (Ambient temp. 20°C) Ω BRN – WHT: 234

PNK (RED) – WHT: 209

— : —

Safety devices Type Thermal fuse

Operating temp. Open °C 130

Close Automatic reclosing

Run capacitor µF 1.2

VAC 440

Remote Control Unit RCS-3HVPSS4E

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

9

2-2-2. Outdoor Unit

Outdoor Unit SAP–CRV93EHN

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Compressor

Type DC Rotary (Hermetic)

Compressor model / Nominal output G4C090LU1ER / 600W

Compressor oil … Amount cc FV50S … 320

Coil resistance (Ambient temp. 20°C) Ω U – V: 0.81

V – W: 0.81

W – U: 0.81

Safety devices

CT (Peak current cut-off control) YES

Compressor discharge temp. control YES

Operation cut-off control in abnormal ambient temp. YES

Run capacitor µF —

VAC —

Crankcase heater —

Fan & Fan Motor

Type … Fan / Fan motor Propeller / AC motor

Q’ty … Dia. mm 1 … 400

Fan motor model … Q’ty IB-976-501 … 1

No. of poles … Rough measure rpm (Cool / Heat) 6 … 700 / 700

Nominal output W 20

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN: 213

RED (PNK) – WHT: 168

— : —

Safety devices Type Thermal fuse

Operating temp. Open °C 150

Close °C Automatic reclosing

Run capacitor on control PCB (A) µF 2.0

VAC 440

Heat Exchanger Coil

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.4

Face area m

2

0.288

External Finish Acrylic baked-on enamel finish

Control PCB

Part No. CB-CRV93EHN (POW-CRV93GJH)

Controls Microprocessor

Control circuit fuse 250V, 20A

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

10

Outdoor Unit SAP–CRV123EHN

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Fan & Fan Motor

Type … Fan / Fan Motor Propeller / DC Motor

Q’ty … Dia. mm 1 … 400

Fan motor model … Q’ty DAJ12-55J71-C … 1

No. of poles … Rough measure rpm (Cool / Heat) 8 … 750 / 750

Nominal output W 50

Coil resistance (Ambient temp. 20°C) Ω —

—

Safety devices Type —

Operating temp. Open °C —

Close °C —

Run capacitor on control PCB (A) µF —

VAC —

Heat Exchanger Coil

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.4

Face area m

2

0.367

External Finish Acrylic baked-on enamel finish

Control PCB

Part No. CB-CRV123EHN (POW-CRV123GJH)

Controls Microprocessor

Control circuit fuse 250V, 20A

Compressor

Type DC Rotary (Hermetic)

Compressor model / Nominal output G4C090LU1ER / 600W

Compressor oil … Amount cc FV50S … 320

Coil resistance (Ambient temp. 20°C) Ω U – V: 0.81

V – W: 0.81

W – U: 0.81

Safety devices

CT (Peak current cut-off control) YES

Compressor discharge temp. control YES

Operation cut-off control in abnormal ambient temp. YES

Run capacitor µF —

VAC —

Crankcase heater —

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

11

2-3. Other Component Specifications

Indoor Unit SAP–KRV93EH

SAP–KRV123EH

Outdoor Unit SAP–CRV93EHN

SAP–CRV123EHN

0

0 102030405060708090

40

60

80

100

120

140

160

180

200

20

10

1

2

3

4

5

6

7

8

9

10

15 20 25 30 35 40

• Indoor air temp sensor

• Indoor heat exchanger sensor

• Compressor temp sensor

Resistance (kΩ)

Temperature (°C)

• Outdoor air temp sensor

• Outdoor heat exchanger sensor

40

35

30

25

20

15

10

5

0

–20 –15 –10 –5 0 5 10 15 20

Temperature (°C)

Resistance (kΩ)

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

12

5 5815

825

285

567

189 3

45

24.5 56

815

56 79.5

40

450187.5

178.9

Wide tube ø9.52(3/8")

Drain hose ø18

Narrow tube ø6.35(1/4")

187.5

178.9

86.5

86.5 45

360

(ø65)

308

187.5187.5

92.5122.5

70

825

450

45

285

40

(ø65)

24.5

40

196

46.5 27.4

70

32

133.8

52 23

3. DIMENSIONAL DATA

Indoor Unit SAP-KRV93EH

SAP-KRV123EH

Unit: mm

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

13

Outdoor Unit SAP-CRV93EHN

SAP-CRV123EHN

720 72

Wide tube service valve

ø9.52 (3/8")

2-ø12 holes

Narrow tube service valve

ø6.35 (1/4")

548

16

109 55

155

2

91

265

91

290

316

538

275

AIR DISCHARGE

(12 class only)

AIR INTAKE

12

ID:2-ø23.6

ID:ø18

Unit: mm

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

14

4. REFRIGERANT FLOW DIAGRAM

4-1. Refrigerant Flow Diagram

Indoor Unit SAP-KRV93EH Outdoor Unit SAP-CRV93EHN

SAP-CRV123EH SAP-CRV123EHN

Compressor

4-way

valve

Accumulator

Wide tube

service

valve

Wide tube

O.D.

ø9.52 mm

(3/8 ")

Narrow

tube

service

valve

Narrow tube

O.D.

ø6.35 mm

(1/4")

Heat exchanger

Muffler

Capillary

tube for

split flow

Cooling cycle

(Defrosting cycle)

Heating cycle

Indoor unit Outdoor unit

Electric

expansion

valve

Modulator

(12 class only)

Strainer

(9 class only)

Muffler

(12 class only)

M

Insulation of Refrigerant Tubing

Because capillary tubing is used in the outdoor unit, both the

wide and narrow tubes of this air conditioner become cold. To

prevent heat loss and wet floors due to dripping of

condensation, both tubes must be well insulated with a

proper insulation material. The thickness of the insulation

should be a min. 8 mm.

After a tube has been insulated,

never try to bend it into a narrow

curve because it can cause the tube

to break or crack.

IMPORTANT

Wide tube

Thickness:

Min. 8 mm

Insulation

Narrow tube

Thickness:

Min. 8 mm

IMPORTANT

CAUTION

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

15

5. PERFORMANCE DATA

5-1. Temperature Charts

Indoor Unit SAP-KRV93EH

Outdoor Unit SAP-CRV93EHN

■ Cooling Characteristics ■ Heating Characteristics

25 30 35 40

17

16

15

14

13

12

11

10

–5 0 5 10 15 20 25

3

2

8

9

6

7

4

5

–5 0 5 10 15 20 25

60

55

50

45

40

35

30

25

Outdoor inlet air D.B. temp.(˚C)

Outdoor inlet air D.B. temp.(˚C) Outdoor inlet air D.B. temp.(˚C)

Operating current (A)

Indoor discharge air temperature (˚C)

–5 0 5 10 15 20 25

Outdoor inlet air D.B. temp.(˚C)

25 30 35 40

4

5

3

2

1.2

(11.2)

1.3

(12.2)

1.1

(10.2)

1.0

(9.2)

3.5

(34.7)

3.0

(29.6)

2.5

(24.5)

2.0

(19.4)

Low pressure at wide tube service valve

MPa (kgf/cm

2

G)

High pressure at wide tube service valve

MPa (kgf/cm

2

G)

27

°C

24

°C

Indoor Air Temp.30

°C

24

°C

27

°C

Indoor Air Temp.30

°C

27

°C

24

°C

Indoor Air Temp.30

°C

20

°C

17

°C

Indoor Air Temp.23°C

20

°C

17

°C

Indoor Air Temp.23

°C

20

°C

17

°C

Indoor Air Temp.23

°C

· Check each performance value in test-run mode. Electrical performance values represent a combined indoor/outdoor value.

· Overload prevention operates to protect the air conditioner when outdoor ambient temperature becomes extremely high in

heating mode. (Refer to “9-2. Overload prevention during heating.”)

● … Points of rating condition

Indoor air temperature 27°C D.B. / 19°C W.B. Heating: Indoor air temperature 20°C D.B.rating condition

Outdoor air temperature 35°C D.B. / 24°C W.B. Outdoor air temperature 7°C D.B. / 6°C W.B.

NOTE

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

16

Indoor Unit SAP-KRV123EH

Outdoor Unit SAP-CRV123EHN

■ Cooling Characteristics ■ Heating Characteristics

Low pressure at wide tube service valve

MPa (kgf/cm

2

G)

High pressure at wide tube service valve

MPa (kgf/cm

2

G)

Outdoor inlet air D.B. temp.(˚C) Outdoor inlet air D.B. temp.(˚C)

Operating current (A)

Indoor discharge air temperature (˚C)

25

1.3

(12.2)

1.0

(9.2)

1.1

(10.2)

30 35 40

1.2

(11.2)

Outdoor fan speed

HighLow

25

4

6

8

9

3

2

5

7

30 35 40

Outdoor fan speed

HighLow

25

8

10

12

14

16

18

30 35 40

Outdoor fan speed

HighLow

–5 0 5 10 15 20 25

2.0

(19.4)

2.5

(24.5)

3.0

(29.6)

3.5

(34.7)

–5 0 5

4

6

8

9

3

2

5

7

10 15 20 25

–5 0 5 10

30

6

25

35

40

45

50

55

20

60

15 20 25

27

°C

24

°C

Indoor Air Temp.30

°C

20

°C

17

°C

Indoor Air Temp.23

°C

Indoor Air Temp.23°C

17

°C

20

°C

Indoor Air Tem

p.30°C

24

°C

27

°C

17

°C

Indoor Air Temp.23

°C

20

°C

27

°C

24

°C

Indoor Air Temp.30°C

· Check each performance value in test-run mode. Electrical performance values represent a combined indoor/outdoor value.

· Overload prevention operates to protect the air conditioner when outdoor ambient temperature becomes extremely high in

heating mode. (Refer to “9-2. Overload prevention during heating.”)

● … Points of rating condition

Indoor air temperature 27°C D.B. / 19°C W.B. Heating: Indoor air temperature 20°C D.B.rating condition

Outdoor air temperature 35°C D.B. / 24°C W.B. Outdoor air temperature 7°C D.B. / 6°C W.B.

NOTE

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

17

5-2. Air Throw Distance Charts

Horizontal distance (m)

Axis air velocity (m/s)

Vertical distance (m)

Room air temp. : 20°C

Fan speed : High

Heating

Horizontal distance (m)

Axis air velocity (m/s)

Vertical distance (m)

Room air temp. : 27°C

Fan speed : High

Cooling

1

2

3

4

123456789

: Flap angle 0° , : Axis air velocity 0°

: Flap angle 30°, : Axis air velocity 30°

1

2

3

4

123456789

: Flap angle 45° , : Axis air velocity 45°

: Flap angle 60° , : Axis air velocity 60°

Indoor Unit SAP–KRV93EH

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

18

Horizontal distance (m)

Axis air velocity (m/s)

Vertical distance (m)

Room air temp. : 20°C

Fan speed : High

Heating

Horizontal distance (m)

Axis air velocity (m/s)

Vertical distance (m)

Room air temp. : 27°C

Fan speed : High

Cooling

1

2

3

4

123456789

: Flap angle 0° , : Axis air velocity 0°

: Flap angle 30°, : Axis air velocity 30°

1

2

3

4

123456789

: Flap angle 45° , : Axis air velocity 45°

: Flap angle 60° , : Axis air velocity 60°

Indoor Unit SAP–KRV123EH

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

19

5-3. Operating Frequency Charts

0

1

2

3

4

5

0 1020304050607080

Operating Freqency (Hz)

Cooling Capacity (kW)

54

Min.

Center

Max.

0

200

400

600

800

1000

1200

0 1020304050607080

Operating Freqency (Hz)

Power Input (W)

54

Min.

Center

Max.

755

2.65

Indoor Unit SAP–KRV93EH

Outdoor Unit SAP–CRV93EHN

230V Single-phase 50Hz

NOTE

1) Rating conditions in cooling are:

Indoor: 27°C D.B. / 19°C W.B.

Outdoor: 35°C D.B. / 24°C W.B.

2) Fan speed: High

■ Cooling

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

20

0

1

2

3

4

5

0 20406080100120

Operating Freqency (Hz)

Heating Capacity (kW)

3.6

Min.

Center

Max.

75

0

200

400

600

800

1000

1200

1400

1600

0 20406080100120

Operating Freqency (Hz)

Power Input (W)

995

Min.

Center

Max.

75

230V Single-phase 50Hz

NOTE

1) Rating conditions in heating are:

Indoor: 20°C D.B.

Outdoor: 7°C D.B. / 6°C W.B.

2) Fan speed: High

■ Heating

Sanyo ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

Leht laadib ...

Sanyo SAP-KRV123EH Technical & Service Manual

See käsiraamat sobib ka

Sanyo SAP-KRV123EH Technical & Service Manual

teistes keeltes

Muud dokumendid