LG 65UF776V Kasutusjuhend

Please read this manual carefully before operating your set and

retain it for future reference.

Safety and Reference

OWNER’S MANUAL

LED TV*

* LG LED TV applies LCD screen with LED backlights.

www.lg.com

*MFL68931015*

P/NO : MFL68931015(1511-REV03)

Printed in Korea

2

ENGLISH

Safety instructions

Please read these safety precautions carefully before

using the product.

WARNING

Do not place the TV and/or remote control in the following

environments:

t A location exposed to direct sunlight

t An area with high humidity such as a bathroom

t Near any heat source such as stoves and other devices that

produce heat

t Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

t An area exposed to rain or wind

t Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

Do not place the product where it might be exposed to dust. This may

cause a re hazard.

Mains Plug is the TV connecting/disconnecting device to AC mains

electric supply. This plug must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands. Additionally, if the cord

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

Make sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

Insert power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

Ensure the power cord does not come into contact with hot objects

such as a heater. This may cause a re or an electric shock hazard.

Do not place a heavy object, or the product itself, on power cables.

Otherwise, this may result in re or electric shock.

Bend antenna cable between inside and outside building to prevent

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

When mounting TV onto wall make sure to neatly install and isolate

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a single multiple electrical

outlet. Otherwise, this may result in re due to over-heating.

ENGLISH

3

Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out

of the reach of children.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury.

Dispose of used batteries carefully to ensure that a small child does not

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

Do not put or store inammable substances near the product. There is a

danger of combustion/explosion or re due to careless handling of the

inammable substances.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

Do not spray water on the product or scrub with an inammable

substance (thinner or benzene). Fire or electric shock accident can

occur.

Do not allow any impact, shock or any objects to fall into the unit,

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there is leakage of gas, open the

windows and ventilate. It may cause a re or a burn by a spark.

Do not disassemble, repair or modify the product at your own

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

4

ENGLISH

If any of the following occur, unplug the product immediately and

contact your local service centre.

t The product has been impacted by shock

t The product has been damaged

t Foreign objects have entered the product

t The product produced smoke or a strange smell

This may result in re or electric shock.

Unplug the TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

If water enters or comes into contact with TV, AC adapter or power

cord please disconnect the power cord and contact service centre

immediately. Otherwise, this may result in electric shock or re.

Only use an authorized AC adapter and power cord approved by

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction or product deformation.

Never Disassemble the AC adapter or power cord. This may result in re

or electric shock.

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an outside antenna and

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as unstable shelves or inclined

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

Only use the attachments / accessories specied by the manufacturer.

When installing the antenna, consult with a qualied service

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

ENGLISH

5

We recommend that you maintain a distance of at least 2 to 7 times

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could cause damage to the

remote control.

Do not mix new batteries with old batteries. This may cause the

batteries to overheat and leak.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight, open replace and electric heaters.

Do not place non-rechargeable batteries in charging device.

Make sure there are no objects between the remote control and its

sensor.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

Do not turn the product On/O by plugging-in or unplugging the power

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

Please follow the installation instructions below to prevent the product

from overheating.

t The distance between the product and the wall should be more

than 10cm.

t Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

t Do not install the product on a carpet or cushion.

t Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings when watching the TV

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

Prevent dust collecting on the power plug pins or outlet. This may cause

a re hazard.

Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

6

ENGLISH

Do not press strongly upon the panel with a hand or sharp object such

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

Avoid touching the screen or holding your nger(s) against it for long

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

When cleaning the product and its components, unplug the power

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(Deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

When unplugging the cable, grab the plug and unplug it, by pulling at

the plug.

Don’t pull at the cord to unplug the power cord from the power board,

as this could be hazardous.

When moving the product, make sure you turn the power o rst. Then,

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

When moving or unpacking the product, work in pairs because the

product is heavy. Otherwise, this may result in injury.

Contact the service centre once a year to clean the internal parts of the

product.

Accumulated dust can cause mechanical failure.

Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

The panel is a high technology display product with resolution of two

million to six million pixels. You may see tiny black dots and/or brightly

coloured dots (red, blue or green) at a size of 1ppm on the panel. This

does not indicate a malfunction and does not aect the performance

and reliability of the product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

ENGLISH

7

You may nd dierent brightness and color of the panel depending on

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

Displaying a still image for a prolonged period of time may cause image

sticking. Avoid displaying a xed image on the TV screen for a long

period of time.

Generated Sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV (e.g. electric

mosquito-swatter). This may result in product malfunction.

Viewing 3D imaging (Only 3D

models)

WARNING

Viewing Environment

t Viewing Time

- When watching 3D contents, take 5 to 15 minute breaks every

hour. Viewing 3D contents for a long period of time may cause

headache, dizziness, fatigue or eye strain.

Those that have a photosensitive seizure or

chronic illness

t Some users may experience a seizure or other abnormal symptoms

when they are exposed to a ashing light or particular pattern

from 3D contents.

t Do not watch 3D videos if you feel nausea, are pregnant and/ or

have a chronic illness such as epilepsy, cardiac disorder, or blood

pressure disease, etc.

t 3D Contents are not recommended to those who suer from stereo

blindness or stereo anomaly. Double images or discomfort in

viewing may be experienced.

t If you have strabismus (cross-eyed), amblyopia (weak eyesight) or

astigmatism, you may have trouble sensing depth and easily feel

fatigue due to double images. It is advised to take frequent breaks

than the average adult.

t If your eyesight varies between your right and left eye, correct your

eyesight prior to watching 3D contents.

Symptoms which require discontinuation or

refraining from watching 3D contents

t Do not watch 3D contents when you feel fatigue from lack of sleep,

overwork or drinking.

t When these symptoms are experienced, stop using/watching 3D

contents and get enough rest until the symptom subsides.

- Consult your doctor when the symptoms persist. Symptoms may

include headache, eyeball pain, dizziness, nausea, palpitation,

blurriness, discomfort, double image, visual inconvenience or

fatigue.

8

ENGLISH

CAUTION

Viewing Environment

t Viewing Distance

- Maintain a distance of at least twice the screen diagonal length

when watching 3D contents. If you feel discomfort in viewing 3D

contents, move further away from the TV.

Viewing Age

t Infants/Children

- Usage/ Viewing 3D contents for children under the age of 6 are

prohibited.

- Children under the age of 10 may overreact and become overly

excited because their vision is in development (for example:

trying to touch the screen or trying to jump into it). Special

monitoring and extra attention is required for children watching

3D contents.

- Children have greater binocular disparity of 3D presentations

than adults because the distance between the eyes is

shorter than that of adults. Therefore they will perceive more

stereoscopic depth compared to adults for the same 3D image.

t Teenagers

- Teenagers under the age of 19 may react with sensitivity due

to stimulation from light in 3D contents. Advise them to refrain

from watching 3D contents for a long time when they are tired.

t Elderly

- The elderly may perceive less 3D eect compared to the young.

Do not sit closer to the TV than the recommended distance.

Cautions when using the 3D glasses

t Make sure to use LG 3D glasses. Otherwise, you may not be able to

view 3D videos properly.

t Do not use 3D glasses instead of your normal glasses, sunglasses or

protective goggles.

t Using modied 3D glasses may cause eye strain or image

distortion.

t Do not keep your 3D glasses in extremely high or low

temperatures. It will cause deformation.

t The 3D glasses are fragile and are easily scratched. Always use a

soft, clean piece of cloth when wiping the lenses. Do not scratch

the lenses of the 3D glasses with sharp objects or clean/wipe them

with chemicals.

Preparing

NOTE

t If the TV is turned on for the rst time after it was shipped from the

factory, initialization of the TV may take a few minutes.

t Image shown may dier from your TV.

t Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

t The available menus and options may dier from the input source

or product model that you are using.

t New features may be added to this TV in the future.

t The TV can be placed in standby mode in order to reduce the power

consumption. And the TV should be turned o if it will not be

watched for some time, as this will reduce energy consumption.

t The energy consumed during use can be signicantly reduced if the

level of brightness of the picture is reduced, and this will reduce

the overall running cost.

t The items supplied with your product may vary depending on the

model.

t Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

t For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

t Use a certied cable with the HDMI logo attached.

t If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur. (Recommended HDMI Cable Types)

- High-Speed HDMI

®

/

TM

cable (3 m or less)

- High-Speed HDMI

®

/

TM

cable with Ethernet (3 m or less)

ENGLISH

9

CAUTION

t Do not use any unapproved items to ensure the safety and product

life span.

t Any damage or injuries caused by using unapproved items are not

covered by the warranty.

t Some models have a thin lm attached on to the screen and this

must not be removed.

t When attaching the stand to the TV set, place the screen facing

down on a cushioned table or at surface to protect the screen

from scratches.

t Make sure that the screws are inserted correctly and fastened

securely. (If they are not fastened securely enough, the TV may tilt

forward after being installed.) Do not use too much force and over

tighten the screws; otherwise screw may be damaged and not

tighten correctly.

t Do not remove the panel with your ngers or any tools. Doing so

may damage the product. (Only UF84**)

Separate purchase

Separate purchase items can be changed or modied for quality

improvement without any notication. Contact your dealer to buy these

items. These devices only work with certain models.

The model name or design may be changed depending on the upgrade

of product functions, manufacturer’s circumstances or policies.

(Depending on model)

AG-F***

Cinema 3D Glasses

AN-MR600

Magic Remote

AG-F***DP

Dual Play Glasses

AN-VC550

Smart camera LG Audio Device

AN-WF500

Wi-Fi/Bluetooth

Dongle

* Some models require Wi-Fi/Bluetooth Dongle for using Magic

Remote or LG Audio Device.

* Supporting device of Wi-Fi/Bluetooth Dongle is a dierent in accord-

ance with model.

Maintenance

Cleaning your TV

Clean your TV regularly to keep the best performance and to extend the

product lifespan.

t Make sure to turn the power o and disconnect the power cord and

all other cables rst.

t When the TV is left unattended and unused for a long time,

disconnect the power cord from the wall outlet to prevent possible

damage from lightning or power surges.

Screen, frame, cabinet and stand

To remove dust or light dirt, wipe the surface with a dry, clean, and

soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in

clean water or a diluted mild detergent. Then wipe immediately with

a dry cloth.

t Avoid touching the screen at all times, as this may result in damage

to the screen.

t Do not push, rub, or hit the screen surface with your ngernail or a

sharp object, as this may result in scratches and image distortions.

t Do not use any chemicals as this may damage the product.

t Do not spray liquid onto the surface. If water enters the TV, it may

result in re, electric shock, or malfunction.

Power cord

Remove the accumulated dust or dirt on the power cord regularly.

10

ENGLISH

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

t It is recommended to move the TV in the box or packing material

that the TV originally came in.

t Before moving or lifting the TV, disconnect the power cord and

all cables.

t When holding the TV, the screen should face away from you to

avoid damage.

t Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

t When transporting a large TV, there should be at least 2 people.

t When transporting the TV by hand, hold the TV as shown in the

following illustration.

t When transporting the TV, do not expose the TV to jolts or

excessive vibration.

t When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

t Do not apply excessive pressure to cause exing /bending of frame

chassis as it may damage screen.

t When handling the TV, be careful not to damage the protruding

joystick button.

CAUTION

t Avoid touching the screen at all times, as this may result in damage

to the screen.

t Do not move the TV by holding the cable holders, as the cable

holders may break, and injuries and damage to the TV may occur.

Using the joystick button

(Image shown may dier from your TV.)

You can simply operate the TV functions, pressing or moving the joystick

button up, down, left or right.

NOTE

t UF64 series does not have a Joystick button but has only a power

On/O button.

Joystick Button

Basic functions

Power On

When the TV is turned o, place your

nger on the joystick button and

press it once and release it.

Power O

When the TV is turned on, place

your nger on the joystick button

and press it once for a few seconds

and release it. All running apps will

close, and any recording in progress

will stop.

Volume

Control

If you place your nger over the

joystick button and move it left or

right, you can adjust the volume level

you want.

Programmes

Control

If you place your nger over the

joystick button and move it up or

down, you can scrolls through the

saved programmes you want.

ENGLISH

11

Adjusting the menu

When the TV is turned on, press the joystick button one time. You can

adjust the Menu items moving the joystick button up, down, left or

right.

Turns the power o.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

Accesses the Quick Settings.

NOTE

t When your nger over the joystick button and push it to the up,

down, left or right, be careful not to press the joystick button. If you

press the joystick button rst, you may not be able to adjust the

volume level and saved programmes.

Mounting on a table

(Image shown may dier from your TV.)

1 Lift and tilt the TV into its upright position on a table.

t Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

t Do not place the TV near or on sources of heat, as this may result in

re or other damage.

Using the kensington security

system

(This feature is not available for all models.)

t Image shown may dier from your TV.

The Kensington security system connector is located at the rear of the

TV. For more information of installation and using, refer to the manual

provided with the Kensington security system or visit http://www.

kensington.com. Connect the Kensington security system cable between

the TV and a table.

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

t If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

CAUTION

t Make sure that children do not climb on or hang on the TV.

NOTE

t Use a platform or cabinet that is strong and large enough to

support the TV securely.

t Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

12

ENGLISH

Mounting on a wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the use

of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with

cables connected. When you do not use LG’s wall mount bracket, please

use a wall mount bracket where the device is adequately secured to the

wall with enough space to allow connectivity to external devices. It is

advised to connect all the cables before installing xed wall mounts.

10 cm

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Separate purchase(Wall mounting bracket)

Model

43UF64**

43UF68**

40/43UF77**

49UF64**

49/55UF68**

49/55UF77**

50UF83**

49/55UF84**

VESA (mm) (A x B) 200 x 200 300 x 300

Standard screw M6 M6

Number of screws 4 4

Wall mount bracket

LSW240B

MSW240

LSW350B

MSW240

Model

65UF68**

60/65UF77**

58UF83**

70/79UF77**

VESA (mm) (A x B) 300 x 300 600 x 400

Standard screw M6 M8

Number of screws 4 4

Wall mount bracket LSW350B LSW640B

A

B

CAUTION

t Disconnect the power rst, and then move or install the TV.

Otherwise electric shock may occur.

t Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

t If you install the TV on a ceiling or slanted wall, it may fall and

result in severe injury. Use an authorised LG wall mount and

contact the local dealer or qualied personnel.

t Do not over tighten the screws as this may cause damage to the TV

and void your warranty.

t Use the screws and wall mounts that meet the VESA standard. Any

damages or injuries by misuse or using an improper accessory are

not covered by the warranty.

NOTE

t Use the screws that are listed on the VESA standard screw

specications.

t The wall mount kit includes an installation manual and necessary

parts.

t The wall mount bracket is not provided. You can obtain additional

accessories from your local dealer.

t The length of screws may dier depending on the wall mount.

Make sure to use the proper length.

t For more information, refer to the manual supplied with the wall

mount.

t When installing the wall mounting bracket, use the adhesive label

or protective cover provided. The adhesive label or protective cover

will protect the opening from accumulating dust and dirt. (Only

when the label or cover is provided)

Provided item

Adhesive label

ENGLISH

13

Provided item

Protective cover

t When attaching a wall mounting bracket to the TV, insert the wall

mount spacers into the TV wall mount holes to adjust the vertical

angle of the TV. (Only when the item of the following form is

provided)

Provided Item

Wall Mount Spacer

t Depending on the shape of the stand, use a at tool to remove the

stand cover as illustrated below. (e.g., a at screwdriver)

(Only when the item of the following form is provided)

Flat tool

Connections (notications)

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

NOTE

t The external device connection may dier from the model.

t Connect external devices to the TV regardless of the order of the

TV port.

t If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

t Refer to the external equipment’s manual for operating

instructions.

t If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

t In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

t In PC mode, some resolution settings may not work properly

depending on the graphics card.

t If ULTRA HD content is played on your PC, video or audio may

become disrupted intermittently depending on your PC’s

performance. (Depending on model)

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

t Use a signal splitter to use more than 2 TVs.

t If the image quality is poor, install a signal amplier properly to

improve the image quality.

t If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

t An antenna cable and converter are not supplied.

t Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,

HE-AAC

t For a location that is not supported with ULTRA HD broadcasting,

this TV cannot receive ULTRA HD broadcasts directly. (Depending

on model)

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω).

14

ENGLISH

Euro scart connection

(Depending on model)

Transmits the video and audio signals from an external device to the

TV set. Connect the external device and the TV set with the euro scart

cable.

Output Type

Current

input mode

AV1

(TV Out

1

)

Digital TV Digital TV

Analogue TV, AV

Analogue TVComponent

HDMI

1 TV Out : Outputs Analogue TV or Digital TV signals.

t Any Euro scart cable used must be signal shielded.

t When watching digital TV in 3D imaging mode, only 2D out signals

can be output through the SCART cable. (Only 3D models)

t If you use the Time Machine function on digital TV, TV out signals

cannot be output through the SCART cable.

CI module connection

(Depending on model)

View the encrypted (pay) services in digital TV mode.

t Check if the CI module is inserted into the PCMCIA card slot in the

right direction. If the module is not inserted properly, this can

cause damage to the TV and the PCMCIA card slot.

t If the TV does not display any video and audio when CI+ CAM is

connected, please contact to the Terrestrial/Cable/Satellite Service

Operator.

USB connection

Some USB Hubs may not work. If a USB device connected using a USB

Hub is not detected, connect it to the USB port on the TV directly.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

t

Picture HDMI ULTRA HD Deep

Colour

- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)

- Off : Support 4K @ 50/60 Hz (4:2:0)

If the device connected to Input Port also supports ULTRA HD Deep

Colour, your picture may be clearer. However, if the device doesn’t

support it, it may not work properly. In that case, connect the device

to a dierent HDMI port or change the TV’s HDMI ULTRA HD Deep

Colour setting to Off.

(This feature is available on certain models which are supported

ULTRA HD Deep Colour only.)

NOTE

t Supported HDMI Audio format :

Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),

DTS (44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

(Depending on model)

Remote control

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the

and ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

CAUTION

t Do not mix old and new batteries, as this may damage the remote

control.

t The remote control will not be included for all sales market.

Make sure to point the remote control toward the remote control sensor

on the TV.

ENGLISH

15

(Depending on model)

A

B

A

(POWER) Turns the TV on or o.

Selects Radio, TV and DTV programme.

Changes the input source.

/ (Q. Settings) Accesses the Quick Settings.

Resizes an image.

Recalls your preferred subtitle in digital mode.

Number buttons Enters numbers.

Shows programme guide.

(Space) Opens an empty space on the screen keyboard.

Returns to the previously viewed programme.

B

Accesses your favourite programme list.

Views the information of the current programme and

screen.

Mutes all sounds.

Adjusts the volume level.

 Scrolls through the saved programmes.

 Moves to the previous or next screen.

C

D

2

1

C

1

Selects the MHP TV menu source. (Depending on model)

1

Shows the previous history. (Depending on model)

(HOME) Accesses the Home menu.

Shows the list of Apps.

Teletext buttons ( ) These buttons are used for

teletext.

Navigation buttons (up/down/left/right) Scrolls through menus

or options.

Selects menus or options and conrms your input.

Returns to the previous level.

Clears on-screen displays and returns to TV viewing.

D

By pressing the AD button, audio descriptions function will be

enabled.

2

Accesses the saved programme list. (Depending on model)

2

Starts to record and displays record menu.

(Only Time Machine

Ready

supported model) (Depending on model)

Control buttons ( ) Controls the Premium

contents, Time Machine

Ready

or SmartShare menus or the SIMPLINK

compatible devices (USB or SIMPLINK or Time Machine

Ready

).

Coloured buttons These access special functions in some menus.

( : Red, : Green, : Yellow, : Blue)

16

ENGLISH

(Depending on model)

B

A

P

A

G

E

FAV

MUTE

1

.,;@

2

abc

3

def

4

ghi

5

jkl

6

mno

7

pqrs

8

tuv

0

9

wxyz

GUIDE

Q.VIEW

RATIO

INFO

A

(POWER) Turns the TV on or o.

Changes the input source.

/ (Q. Settings) Accesses the Quick Settings.

Resizes an image.

(User Guide) Sees user- guide.

Number buttons Enters numbers.

(Space) Opens an empty space on the screen keyboard.

Shows programme guide.

Returns to the previously viewed programme.

B

Adjusts the volume level.

Accesses your favourite programme list.

Views the information of the current programme and screen.

Mutes all sounds.

 Scrolls through the saved programmes.

 Moves to the previous or next screen.

C

D

EXIT

OK

LIVE MENU

MY APPS

LIVE TV

REC/

TEXT

T.OPT

APP/

AD

BACK

TV/RAD

RECENT

SUBTITLE

C

Shows the previous history.

(HOME) Accesses the Home menu.

Shows the list of Apps.

Navigation buttons (up/down/left/right) Scrolls through menus

or options.

Selects menus or options and conrms your input.

Returns to the previous level.

Shows the list of Recommended, Programmes, Search

and Recorded. (Depending on model)

Clears on-screen displays and returns to TV viewing.

D

Coloured buttons These access special functions in some menus.

(

: Red, : Green, : Yellow, : Blue)

Teletext buttons ( ) These buttons are used for

teletext.

Selects the MHP TV menu source. (Depending on model)

Returns to LIVE TV.

Control buttons ( ) Controls the Premium

contents, Time Machine

Ready

or SmartShare menus or the SIMPLINK

compatible devices (USB or SIMPLINK or Time Machine

Ready

).

Starts to record and displays record menu. (Only Time

Machine

Ready

supported model) (Depending on model)

Recalls your preferred subtitle in digital mode.

By Pressing AD button, audio descriptions function will be

enabled.

Selects Radio, TV and DTV programme.

ENGLISH

17

Magic remote functions

(Depending on model)

When the message “Magic remote battery is low. Change the battery.”

is displayed, replace the battery.

To replace batteries, open the battery cover, replace batteries (1.5 V AA)

matching the

and ends to the label inside the compartment,

and close the battery cover. Be sure to point the magic remote toward

the remote control sensor on the TV. To remove the batteries, perform

the installation actions in reverse.

CAUTION

t Do not mix old and new batteries, as this may damage the remote

control.

6

mno

9

wxyz

3

def

2

abc

1

. @

4

ghi

8

tuv

7

pqrs

0

5

jkl

LIST

INFO

EXIT

A

B

A

(POWER) Turns the TV on or o.

(INPUT) Changes the input source.

* Pressing and holding the

button displays all the lists of exter-

nal inputs.

Number buttons Enters numbers.

Accesses the saved programmes list.

Views the information of the current programmes and screen.

B

Adjusts the volume level.

Scrolls through the saved programmes.

(MUTE) Mutes all sounds.

* By Pressing and holding the button, video/audio descriptions

function will be enabled. (Depending on model)

(HOME) Accesses the Home menu.

(BACK) Returns to the previous screen.

Clears on-screen displays and returns to Last Input viewing.

GUIDE

EXIT

TEXT

T.OPT

SUBT.

C

D

C

Wheel (OK) Press the center of the Wheel button to select a

menu. You can change programmes by using the Wheel button.

(up/down/left/right) Press the up, down, left or

right button to scroll the menu. If you press buttons

while the pointer is in use, the pointer will disappear from the screen

and Magic Remote will operate like a general remote control. To

display the pointer on the screen again, shake Magic Remote to the

left and right.

Shows programme guide.

(Screen Remote) Displays the Screen Remote.

* Accesses the Universal Control Menu. (Depending on model)

18

ENGLISH

D

Used for viewing 3D video. (Only 3D models)

(Voice recognition)

(Depending on model)

Network connection is required to use the voice recognition function.

1 Press the voice recognition button.

2 Speak when the voice display window appears on the TV screen.

t Use the Magic Remote no further than 10 cm from your face.

t The voice recognition may fail when you speak too fast or too

slowly.

t The recognition rate may vary depending on the user’s

characteristics (voice, pronunciation, intonation, and speed) and

the environment (noise and TV volume).

(Q. Settings) Accesses the Quick Settings.

* Pressing and holding the button displays the Advanced

menu.

Coloured buttons These access special functions in some menus.

( : Red, : Green, : Yellow, : Blue)

Teletext buttons ( , )

These buttons are used for

teletext.

Recalls your preferred subtitle in digital mode.

Registering magic remote

How to register the magic remote

To use the Magic Remote, rst pair it with your TV.

1 Put batteries into the Magic Remote and turn the TV on.

2 Point the Magic Remote at your TV and press the Wheel (OK) on

the remote control.

* If the TV fails to register the Magic Remote, try again after turning

the TV off and back on.

How to deregister the magic remote

Press the (BACK) and (HOME) buttons at the same time, for

ve seconds, to unpair the Magic Remote with your TV.

* Pressing and holding the button will let you cancel and re-reg-

ister Magic Remote at once.

How to use magic remote

t Shake the Magic Remote slightly to the right and left or press

(HOME), (INPUT), buttons to make the pointer

appear on the screen.

(In some TV models, the pointer will appear when you turn the

Wheel (OK) button.)

t If the pointer has not been used for a certain period of time or

Magic Remote is placed on a at surface, then the pointer will

disappear.

t If the pointer is not responding smoothly, you can reset the pointer

by moving it to the edge of the screen.

t The Magic Remote depletes batteries faster than a normal remote

due to the additional features.

Precautions to take when using the

magic remote

t Use the remote control within the specied range (within 10 m).

You may experience communication failures when using the device

outside the coverage area or if there are obstacles within the

coverage area.

t You may experience communication failures depending on the

accessories.

Devices such as a microwave oven and wireless LAN operate in the

same frequency band (2.4 GHz) as the Magic Remote. This may

cause communication failures.

t The Magic Remote may not work properly if a wireless router (AP)

is within 1 meter of the TV.

Your wireless router should be more than 1 m away from the TV.

t Do not disassemble or heat the battery.

t Do not drop the battery. Avoid extreme shocks to the battery.

t Inserting the battery in the wrong way may result in explosion.

ENGLISH

19

Licenses

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

Open source software

notice information

To obtain the source code under GPL, LGPL, MPL and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

External control device

setup

To obtain the external control device setup information, please visit

www.lg.com.

Troubleshooting

Cannot control the TV with the remote control.

t Check the remote control sensor on the product and try again.

t Check if there is any obstacle between the product and the remote

control.

t Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

t Check if the product is turned on.

t Check if the power cord is connected to a wall outlet.

t Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

t Check the power control settings. The power supply may be

interrupted.

t Check if the

Automatic Standby(Depending on model) / Sleep

Timer / Timer Power Off is activated in the TIMERS settings.

t If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is

displayed.

t Turn the TV o/on using the remote control.

t Reconnect the HDMI cable.

t Restart the PC with the TV on.

20

ENGLISH

Specications

Wireless module

specification

t Because band channel used by the country could be dierent, the

user can not change or adjust the operating frequency and this

product is set for the regional frequency table.

t This device should be installed and operated with minimum

distance 20 cm between the device and your body. And this phrase

is for the general statement for consideration of user environment.

0197

(Only UF68**, UF77**, UF83**, UF84**)

Wireless module (LGSBW41) specification

Wireless LAN Bluetooth

Standard IEEE 802.11a/b/g/n Standard

Bluetooth

Version 4.0

Frequency

Range

2400 to 2483.5 MHz

5150 to 5250 MHz

5725 to 5850 MHz (for

Non EU)

Frequency

Range

2400 to

2483.5 MHz

Output

Power

(Max.)

802.11a: 13 dBm

802.11b: 15 dBm

802.11g: 14 dBm

802.11n - 2.4 GHz: 16 dBm

802.11n - 5 GHz: 16 dBm

Output

Power

(Max.)

10 dBm or

Lower

(Only UF64**)

Wireless LAN module (TWFM-B006D) specification

Standard IEEE 802.11a/b/g/n

Frequency Range

2400 to 2483.5 MHz

5150 to 5250 MHz

5725 to 5850 MHz (for Non EU)

Output Power (Max.)

802.11a: 11 dBm

802.11b: 14 dBm

802.11g: 10.5 dBm

802.11n - 2.4 GHz: 11 dBm

802.11n - 5 GHz: 12.5 dBm

Leht laadib ...

LG 65UF776V Kasutusjuhend

LG 65UF776V Kasutusjuhend

teistes keeltes

Seotud paberid