Sony SU-WL450 Installation Information

E-600-100-11(2)

SU-WL450

Wall-Mount

Bracket

Installation Information

GB

Informations d’installation

FR

Información de instalación

ES

Installationsinformationen

DE

Installatie-informatie

NL

Informazioni sull’installazione

IT

Installationsinformation

SE

Informacje dotyczące instalacji

PL

Informações de instalação

PT

Oplysninger om montering

DK

Asennustiedot

FI

Installasjonsveiledning

NO

Πληροφορίες εγκατάστασης

GR

Montaj Bilgileri

TR

Szerelési információk

HU

Instalační informace

CZ

Informácie týkajúce sa montáže

SK

Informaţii de instalare

RO

Информация за монтаж

BG

Информация по установке

RU

Інформація про встановлення

UA

Paigaldusteave

EE

Uzstādīšanas informācija

LV

Montavimo informacija

LT

Navodila za uporabo

SI

Informacije za instalaciju

HR

Орнату ақпараты

KZ

Informacije za montažu

SR

הנקתה תוארוה

HE

− 2 (GB) −

Installation Information for

Using Sony Wall-Mount Bracket (SU-WL450)

Supported models*:

KD-85XH95xx / 49XH95xx

KE-85XH95xx / 49XH95xx

* In the actual model names, the “xx” indicates numbers and/or characters specific to each model.

To Customers

For product protection and safety reasons, Sony strongly recommends that installation of your TV

be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony Dealers and Contractors

Provide full attention to safety during the installation, periodic maintenance and examination of this

product.

Sufficient expertise is required for installing this product, especially to determine the

strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment

of this product to the wall to Sony dealers or licensed contractors and pay adequate

attention to safety during the installation. Sony is not liable for any damage or injury

caused by mishandling or improper installation.

For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV Setup

Guide and the directions in this manual.

− 3 (GB) −

GB

Wall-Mount Bracket

On Safety

Thank you for purchasing this product.

To Customers

Installing the TV to the Wall

WARNING

PROFESSIONAL INSTALLATION

REQUIRED

This product should only be installed by

a professional installer who is trained to

determine the strength of the wall for

withstanding the TV’s weight. If it is not

properly secured during installation, the

TV may fall and cause serious injury.

Sony is not liable for any damage or

injury caused by mishandling or

improper installation, or installing any

other than the specified product. Your

Statutory Rights (if any) are not affected.

To Sony dealers

Sufficient expertise is required for

installing this product. Be sure to read

this instruction manual thoroughly to do

the installation work safely. Sony is not

liable for any damages or injury caused

by mishandling or improper installation.

Please give this manual to the customer

after installation.

This instruction manual shows the correct

handling of the product and important

precautions necessary to prevent accidents.

It is your responsibility to read, thoroughly

understand, and follow all instructions in this

instruction manual. Failure to do so may

result in serious personal injury or property

damage, and may void the warranty. Keep

this manual available for future reference.

Products by Sony are designed with safety in

mind. If the products are used incorrectly,

however, it may result in a serious injury

through fire, electric shock, the product

toppling over, or the product dropping. Be

sure to observe the precautions for safety to

prevent such accidents.

CAUTION

Specified products

This Wall-Mount Bracket is designed for use

with the products specified TVs. For TVs,

refer to their Reference Guide to verify that

the Wall-Mount Bracket can be used.

To Customers

WARNING

If the following precautions are not

observed, serious injury or death

through fire, electric shock, or the

product dropping can result.

Be sure to subcontract

the installation to

licensed contractors and

keep small children away

during the installation.

If the Wall-Mount Bracket or the TV is not

installed correctly, the following accidents

may occur. Be sure licensed contractors carry

out installation.



The TV may fall and cause a serious injury

such as a bruise or a fracture.



If the wall on which the Wall-Mount

Bracket is installed is unstable, uneven, or

not perpendicular to the floor, the unit

may fall and cause injury or property

damage. The wall should be capable of

supporting a weight of at least four times

the TV weight.

(Refer to your TV’s Reference Guide for its

weight.)



If the installation of the Wall-Mount

Bracket on the wall is not sufficiently

sturdy, the unit may fall and cause injury or

property damage.

Be sure to subcontract

moving or dismounting

of the TV to licensed

contractors.

If persons other than licensed contractors

transport or dismount the TV, it may fall and

cause injury or property damage. Be sure

that two or more persons (three or more

persons for 75 inches and above TV set) carry

or dismount the TV.

Do not remove screws,

etc., after mounting the

TV.

If you do so, the TV may fall and cause injury

or property damage.

Do not make alterations

to the parts of the Wall-

Mount Bracket.

If you do so, the Wall-Mount Bracket may fall

and cause injury or property damage.

Do not mount any

equipment other than

the specified product.

This Wall-Mount Bracket is designed for use

with the specified product only. If you mount

equipment other than specified, it may fall or

break, and cause injury or property damage.

Do not apply any load

other than the TV on the

Wall-Mount Bracket.

Do not shake the TV left/

right, up/down.

If you do so, the TV may fall and cause injury

or property damage.

Do not lean on or hang

from the TV.

Do not lean on or hang from the TV as it may

fall on you and cause serious injury.

CAUTION

If the following precautions are not

observed, injury or property damage

may occur.



Be sure to store the unused parts in a safe

place for future use.

Keep them away from children.

Do not handle the

product with excessive

force during cleaning or

maintenance.

Do not apply excessive force on the topside

of the TV. If you do so, the TV may fall and

cause injury or property damage.

Precautions



If you use the TV installed on the

Wall-Mount Bracket for a long time, the

wall behind or above the TV may become

discolored or the wallpaper may come

unstuck, depending on the material of the

wall.



If the Wall-Mount Bracket is removed after

installing it on the wall, the screw holes are

left.



Do not use the Wall-Mount Bracket in a

place where it is subjected to mechanical

vibrations.

Installing the Wall-

Mount Bracket

To Sony Dealers

WARNING

The following instructions are for Sony

dealers only. Be sure to read safety

precautions described above and pay

special attention to safety during the

installation, maintenance and checking

of this product.

− 4 (GB) −

Do not install the Wall-

Mount Bracket on wall

surfaces where the

corners or the sides of

the TV protrude away

from the wall surface.

Do not install the Wall-Mount Bracket on wall

surfaces such as a pillar, where the corners

or the sides of the TV protrude away from

the wall surface. If a person or object

happens to hit the protruded corner or side

of the TV, it may cause injury or property

damage.

Do not install the TV over

or under an air-

conditioner.

If the TV is exposed to water leaks or air

current from an air conditioner for a long

time, it may cause a fire, an electric shock or

a malfunction of the TV.

Be sure to install the

Wall-Mount Bracket

securely to the wall

following the instructions

in this instruction

manual.

If any of the screws are loose or fall out, the

Wall-Mount Bracket may fall and cause injury

or property damage. Be sure to use the

appropriate screws for the material of the

wall and install the unit securely using four

or more screws of 8 mm diameter (or

equivalent).

Be sure to use the

supplied screws and

attachment parts

properly following the

instructions given in

this instruction

manual. If you use

substitute items, the

TV may fall and cause

bodily injury to

someone or damage to

the TV.

Be sure to assemble the

bracket properly

following the instructed

procedure explained in

this instruction manual.

If any of the screws are loose or fall out, the

TV may fall and cause bodily injury to

someone or damage to the TV.

Be sure to tighten the

screws securely in the

designated position.

If you fail to do so, the TV may fall and cause

bodily injury to someone or damage to the

TV.

Be careful not to subject

the TV to shock during

installation.

If the TV is exposed to shock, it may fall or

break apart. This may cause injury.

Be sure to install the TV

on a wall that is both

perpendicular and flat.

If you fail to do so, the TV may fall and cause

injury.

After proper installation

of the TV, secure the

cables properly.

If people or objects get tangled with cables,

this may result in injury or damage to the TV.

Do not allow the mains

lead or the connecting

cable to be pinched.

If the mains lead or the connecting cable is

pinched between the unit and the wall or is

bent or twisted by force, the internal

conductors may become exposed and cause

a short circuit or an electrical break. This may

cause a fire or an electric shock.

The screws needed to

secure the Wall-Mount

Bracket to the wall are

not supplied.

Use the appropriate screws for the wall

material and structure when mounting the

Wall-Mount Bracket.

− 5 (GB) −

GB

Before getting started

Firstly, check the type of the wall to install the TV.

What is your wall made of?

Dry wall with studs

Precautions



Maximum dry wall thickness:

16 mm.



Ensure that the inner wood stud size is at

least 51 x 102 mm for common or

38 x 89 mm for nominal.

Solid Concrete or Concrete Block

Precautions



Mount the Wall-Mount Bracket directly

onto the solid concrete wall.



Ensure that the thickness of solid concrete

wall is at least 203 mm.



Ensure that the size of each concrete block

is at least 203 x 203 x 406 mm.

− 6 (GB) −

Preparing for installation



Have the TV’s Reference Guide and Setup

Guide at hand before installation.



Confirm the installing position of your TV.



Prepare four or more screws of 8 mm

diameter and one screw of 5 mm or

equivalent (not supplied). Select screws

suitable for the material of the wall.

Checking the parts

Supplied with SU-WL450



Verify that all the parts are included.

 Base (20) (1)  Pulley (2)

 PSW 6x20 (4)  Spacer (20) (2)

 Belt (1)  Base Adaptor (2)

 PSW 4x10 (8)  Spacer (60) (2)

 PSW 6x50 (2)



These parts may not be used for your

model.

 PSW 4x20 with

Bush (2)

 Bush (20) (M4) (2)

 PSW 4x20 (2)  Bush (M4) (2)

 PSW 4x50 (2)

Table of Contents

What is your wall made of? ............................. 5

Preparing for installation ................................. 6

Checking the parts ........................................... 6

Installing the Wall-Mount Bracket to the

wall ................................................................... 8

Preparing for the installation of the TV .......... 11

KD-85XH95xx, KE-85XH95xx ............................... 11

KD-49XH95xx, KE-49XH95xx ...............................12

Installing the TV on the wall ........................... 13

KD-85XH95xx, KE-85XH95xx ...............................13

KD-49XH95xx, KE-49XH95xx .............................. 16

Confirming the completion of the

installation ......................................................19

Other information ............................................... 19

Specifications ..................................................19

− 7 (GB) −

GB

Tools needed

*1

5.5 mm 10 mm

*2

1.5 N·m

{15 kgf·cm}

*3

1.5 N·m

{15 kgf·cm}

(4)

*2

8 mm x 60 mm

(4)

*4

5 mm

*1 Only for dry wall with studs

*2 Only for solid concrete or concrete block

*3 Depending on models

*4 Only for TV above 75”

− 8 (GB) −

Installing the Wall-Mount Bracket to the wall

1 Decide on the installation location.

Make sure that the wall has enough space for the TV and is capable of supporting a weight of at

least four times that of the TV.

Refer to the following table on installing the TV to the wall. Refer to your TV’s Reference Guide

for the TV’s weight.

f

Screen centre point

Standard mounting Slim mounting

(mm)

Model Name

f

KD-85XH95xx

KE-85XH95xx

1,910 1,099 211 764 136 94

KD-49XH95xx

KE-49XH95xx

1,093 629 163 480 132 90

Note



Figures in the table may differ slightly depending on

the installation.



When your TV is installed on the wall, the upper side

of the TV slightly leans forward.



We recommend you to check the position of TV in the

viewing environment.

− 9 (GB) −

GB

2 Select Wall mounting style. It is

selectable as shown below.

2-a Standard mount

2-b Slim mount

Refer to the table of step 1.

WARNING



When 2-b is selected, rear terminal access is limited.

2-a 2-b

3 Refer to the below table about

the Base Adaptor fitting

location. In case of selecting

2-b, then skip this step.

Model Name Hook location

KD-85XH95xx

a

KE-85XH95xx

KD-49XH95xx

c

KE-49XH95xx

a

d

b

c

Fit Base Adaptor  by using

Screw (PSW 4x10)  to Base

(20)  when selecting 2-a.









4 Decide the positions of the

screws for installing the Base

(20) .

Refer to the specifications on page 19.

When selecting 2-a, please use the hole

positions of Base Adaptor .

WARNING



Determine the strength of the wall the TV will be

mounted on. Reinforce the wall sufficiently, if

necessary.



The wall that the TV will be mounted on should be

able to support a weight of at least four times that of

the TV (Refer to your TV’s Reference Guide for its

weight.).

2-a





2-b



− 10 (GB) −

5 Drill pilot holes on the marks.

Make sure the location on the wall to drill

the holes are strong enough to support a

weight of at least four times that of the TV.

Dry wall with studs

75 mm

5.5 mm

Stud or Reinforcement

Note



Pilot holes must be drilled to a depth of 75 mm, using

a 5.5 mm diameter drill bit.

Solid Concrete or Concrete Block

10 mm

75 mm

6 Install the Base (20)  on the

wall using suitable screws (not

supplied).

Note



Use four or more screws of 8 mm diameter or

equivalent (not supplied).



Use a level to check whether the Base (20)  is level.



Fit four screws to the holes of Base Adaptor 

with Base (20)  (2-a only).

2-a





2-b



− 11 (GB) −

GB

Preparing for the installation

of the TV

Make sure to attach the Table-Top Stand

before installing the TV to the wall by referring

to the Setup Guide.

KD-85XH95xx,

KE-85XH95xx

1 Mark the installation location on

the wall.



Use masking tape, etc. (not supplied) to

mark the location of the TV near the

Base or Base Adaptor. Refer to the

following table.

Screen centre point

Masking tape

(1,000)

(300)

(mm)

Model Name

KD-85XH95xx

KE-85XH95xx

1,910 644 200 211

2 Remove the screws from the

rear of the TV.

Note



Be sure to store the removed screws and unused

parts in a safe place, keeping them away from

children.

3 Attach the Attachment parts for

Wall-Mount Bracket. Check the

Attachment parts by referring to

“Supplied with SU-WL450” in

“Checking the parts” on page

6.

Note



Firmly secure the Attachment parts using screws.



When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Standard mounting (2-a)

Belt 

Spacer

(60 mm) 

Screw (+PSW 6 x 50) 

Pulley 

Screw

(+PSW 6 x 20) 

Slim mounting (2-b)

Belt 

Screw (+PSW 6 x 20) 

Pulley 

Spacer (20 mm)



− 12 (GB) −

4 Connect the necessary cable(s)

to the TV.

Make sure to connect the cables before

installing the TV on the wall. You will be

unable to connect the cables when the TV

is installed.

Note



Subcontract the cable routing in the wall to a licensed

contractor.



Bundle the connecting cables to prevent stepping on

them before wall mounting.

5 Detach the Table-Top Stand

from the TV.

Note



Be careful when lifting the TV as the Table-Top Stand

is detached, the Table-Top Stand may topple over

and cause personal injury.



Take care when removing the Table-Top Stand from

the TV to prevent it from falling over and damaging

the surface that the TV is sitting on.



Be sure to store the removed screws and unused

parts in a safe place, keeping them away from

children.

KD-49XH95xx,

KE-49XH95xx

1 Remove the screws from the

rear of the TV.

Note



Be sure to store the removed screws and unused

parts in a safe place, keeping them away from

children.

2 Attach the Attachment parts for

Wall-Mount Bracket. Check the

Attachment parts by referring to

“Supplied with SU-WL450” in

“Checking the parts” on page

6.

Note



Firmly secure the Attachment parts using screws.



When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Standard mounting (2-a)

Belt 

Spacer

(60 mm) 

Screw (+PSW 6 x 50) 

Pulley 

Screw

(+PSW 6 x 20) 

Slim mounting (2-b)

Belt 

Screw (+PSW 6 x 20) 

Pulley 

Spacer (20 mm)



3 Connect the necessary cable(s)

to the TV.

Make sure to connect the cables before

installing the TV on the wall. You will be

unable to connect the cables when the TV

is installed.

Note



Subcontract the cable routing in the wall to a licensed

contractor.



Bundle the connecting cables to prevent stepping on

them before wall mounting.

− 13 (GB) −

GB

4 Detach the Table-Top Stand

from the TV.

Note



Be careful when lifting the TV as the Table-Top Stand

is detached, the Table-Top Stand may topple over

and cause personal injury.



Take care when removing the Table-Top Stand from

the TV to prevent it from falling over and damaging

the surface that the TV is sitting on.



Be sure to store the removed screws and unused

parts in a safe place, keeping them away from

children.

Installing the TV on the wall

KD-85XH95xx,

KE-85XH95xx

WARNING



Be sure that two or more persons (three or more

persons for 75 inches and above TV set) hold the TV

when carrying it.

1 Lift the TV.



For the location of the Pulleys  to the

hang on the Base or Base Adaptor, refer

to the table of step 3 in “Installing the

Wall-Mount Bracket to the wall” on page

9.



Make sure that the rear of the TV

touches the Base or Base Adaptor when

holding the TV.

Note



Hold the TV securely with both hands and make sure

the Belt  and the bottom of the TV align with the

masking tape.



Carry the TV with three people and the person who is

in front of the TV leads the others to adjust the

position.

− 14 (GB) −



Take great care when installing the TV to the wall

especially for the person who is supporting the TV

from below, the television set may fall, causing

serious bodily injury or even death.





2 Install the TV onto the Base or

Base Adaptor.



Gently slide down the TV and hang the

Pulleys  attached to the rear of the TV

to the Base or Base Adaptor, making

sure to confirm the shape of the holes.



After installing the TV on the wall,

confirm the Pulleys  are firmly latched

into the Base or Base Adaptor.



Release both hands slowly to ensure

that the TV does not fall.



After installing the TV on the wall,

remove the masking tape, etc. from the

wall.

− 15 (GB) −

GB

2-a







2-b







− 16 (GB) −

3 Preventing the bottom of the TV

from shifting.



Take up the slack of Belt  and attach it

to the wall tightly.

2-a 2-b

 



Use a 5 mm diameter screw or

equivalent (not supplied).

Note



Try to pull the bottom of the TV towards yourself

slightly, to make sure that it does not move forward.

If there is any movement, it is not fixed correctly, and

the Belt  should be secured firmly again.

KD-49XH95xx,

KE-49XH95xx

WARNING



Be sure that two or more persons (three or more

persons for 75 inches and above TV set) hold the TV

when carrying it.

1 Lift the TV.



For the location of the Pulleys  to the

hang on the Base or Base Adaptor, refer

to the table of step 3 in “Installing the

Wall-Mount Bracket to the wall” on page

9.



Make sure that the rear of the TV

touches the Base or Base Adaptor when

holding the TV.



Note



Hold the TV securely with both hands.

2 Install the TV onto the Base or

Base Adaptor.



Gently slide down the TV and hang the

Pulleys  attached to the rear of the TV

to the Base or Base Adaptor, making

sure to confirm the shape of the holes.



After installing the TV on the wall,

confirm the Pulleys  are firmly latched

into the Base or Base Adaptor.



Release both hands slowly to ensure

that the TV does not fall.

− 17 (GB) −

GB

2-a







2-b







− 18 (GB) −

3 Preventing the bottom of the TV

from shifting.



Take up the slack of Belt  and attach it

to the wall tightly.

2-a 2-b

 



Use a 5 mm diameter screw or

equivalent (not supplied).

Note



Try to pull the bottom of the TV towards yourself

slightly, to make sure that it does not move forward.

If there is any movement, it is not fixed correctly, and

the Belt  should be secured firmly again.

− 19 (GB) −

GB

Confirming the completion of

the installation

Check the following points.



The Pulleys  are firmly hung onto the Base

or Base Adaptor.



The cord and the cable are not twisted or

pinched.



The Belt  is tight with no slack.

WARNING



Improper placement of the mains lead, etc., may cause

fire or electric shock through a short circuit. Be sure to

confirm the completion of the installation for safety.

Other information

When removing the TV, reverse the previous

installation procedure.

WARNING



Be sure that two or more persons (three or more persons

for 75 inches and above TV set) hold the TV when

removing it.

Specifications

f

c

d

b

a

g

e

h2h1

Dimensions: (Approx.) [mm]

a : 400

b : 300

c : 200

d : 100

e : 80

f : 480

g : 100

h1 : 20 (case 2-b)

h2 : 60 (case 2-a)

Mass (base only): (Approx.) [kg]

0.8

Design and specifications are subject to change without

notice.

− 2 (FR) −

Informations d’installation pour l’utilisation

du Support de fixation murale Sony

(SU-WL450)

Modèles pris en charge* :

KD-85XH95xx / 49XH95xx

KE-85XH95xx / 49XH95xx

* Dans les noms de modèles réels, le « xx » indique des numéros et/ou des caractères spécifiques à

chaque modèle.

À l’attention des clients

Pour des raisons de protection du produit et de sécurité, Sony recommande vivement que

l’installation de votre téléviseur soit effectuée par un revendeur Sony ou un installateur agréé.

N’essayez pas de l’installer vous-même.

A l’attention des revendeurs et installateurs Sony

Soyez particulièrement attentif à la sécurité pendant l’installation, l’entretien périodique et l’examen

du produit.

Une certaine expérience est requise pour installer ce produit, en particulier pour

déterminer la résistance du mur qui devra supporter le poids du téléviseur. Veillez à

confier la fixation de ce produit au mur à un revendeur Sony ou un installateur agréé et

apportez une attention suffisante à la sécurité pendant l’installation. Sony n’est

responsable d’aucun dégât ou blessure provoqué par une erreur de manipulation ou

installation incorrecte.

Pour la sécurité et une installation correcte, suivez le Mode d’emploi du Support de fixation murale,

le Guide d’installation du téléviseur et les consignes de ce manuel.

Leht laaditakse ...

Sony SU-WL450 Installation Information

See juhend sobib ka

Sony SU-WL450 Installation Information

teistes keeltes

Seotud paberid

Muud dokumendid