Silvercrest KH 6522 Operating Instructions Manual

Bränd: Silvercrest

Mudel: KH 6522

Kategooria: DVD-mängijad

Tüüp: Operating Instructions Manual

See käsiraamat sobib ka

KH 6521

KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH6521/22 - 07/09-V4

DVD PLAYER

KH 6522

KH 6521

3AB

DVD Player

Operating instructions

DVD-soitin

Käyttöohje

DVD-Player

Οδηγίες χρήσης

DVD-spelare

Bruksanvisning

CV_KH6521_22_33138_39_LB3AB 26.08.2009 14:46 Uhr Seite 1

qweruyt

KH 6521 / 6522

fg hjk

l;2@2#

as d

2)2!

;

CV_KH6521_22_33138_39_LB3AB 26.08.2009 14:46 Uhr Seite 4

- 1 -

INDEX PAGE

1. Technical Data 2

2. Intended use 2

3. Package contents 2

4. Operating components 2

5. Setting up of the DVD player 3

6. Safety instructions 3

7. Remote control 4

7.1 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

7.2 Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

7.3 Replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

8. Connecting the DVD player to a television 4

8.1 Connecting to a television via ScartCable/RGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

8.2 Connecting to a television via S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

8.3 Connection to a television via video input (Composite Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

8.4 Connecting via component signal (YPbPr/YUV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

8.5 Connecting to a television via HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

9. Connecting audio components to the DVD player 6

9.1 Requirements for the connection of a HiFi system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

9.2 Connecting digital audio components via digital cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

9.3 Connecting audio components via an analogue cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

9.4 Connecting the headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

10. OSD menu settings 8

10.1 Using the OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

10.2 Setup menu GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

10.3 Setup menu AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

10.4 Setup menu DOLBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

10.5 Setup menu VIDEO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

10.6 Setup menu PREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

11. Initial operation of the DVD player 12

11.1 Inserting the DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

11.2 Inserting memory cards/USB memory sticks with MP3/WMA/ MPEG4/JPEG data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

11.3 Removing memory cards/USB memory sticks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

12. Playing back DVDs, VCDs or S-VCDs 13

12.1 Features during playback of a DVD, VCD or S-VCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

13. Playback of JPEG-Photo CD/WMA/MP3/MPEG4 18

14. CD Ripping function 19

15. Cleaning of the DVD player 20

16. Disposal 20

17. Troubleshooting 20

18. Glossary / Key Word Index 21

19. Warranty and Service 23

20. Importer 23

Read these operating instructions carefully before using the device for the first time and preserve this manual for later reference.

Pass this manual on to whoever might acquire the device at a future date.

- 2 -

DVD-PLAYER KH6521/22

1. Technical Data

This device complies in regards to conformance with the basic requirements

and other relevent regulations of the EMV directive 2004/108/EC, as well

as the directive for low voltage devices 2006/95/EC.

Power supply: AC 220 V - 240 V

50 Hz

Power consumption: 20 Watt

Power consumption:

Standby: < 1 W

Protection class: II /

TV standard: PAL/NTSC

Operating temperature: +5

+40°C

Humidity: 5

90% (no condensation)

Measurements

(L x W x H): 220 x 430 x 44 mm

Weight : 1,6 kg approx.

Laser class: 1

Video Output

Format: 4:3 / 16:9

Decoder: MPEG 2

D/A converter: 12 Bit

Audio Output

Decoder: MPEG Dolby Digital (AC-3)

DTS only possible with additional external decoder

D/A converter: 24 Bit / 96 kHz

USB port

Readable

USB memory sticks: USB1.1 and 2.0 up to a capacity of 4 GB

Max. current output: 100 mA

Memory card slot

Readable memory cards: SD (2 GB no SDHC), MS/MSPro (4 GB),

MMC (4 GB)

Headphones output

Jackplug: 3,5 mm

Maximum

output voltage: approx. 25 mV

Playable mediums/formats

VIDEO: DVD, DVD+R, DVD+RW, DVD-R, DVD-RW,

DVD-R DL, DVD+R DL, VCD, S-VCD

Audio: CD, CD-R, CD-RW, Audio-DVD, MP3, WMA,

OGG Vorbis

Additional formats: AVI, MPEG 4, Xvid, JPEG (Foto-CD)

Regional code: or

2. Intended use

The SilverCrest KH 6521/22 DVD player is intended exclusively for stationary

use in enclosed spaces. The device is intended exclusively for private,

non-commercial use.

The device is intended for use as a home entertainment device.

No liability/guarantee will be assumed for damage that results from use other

than that for which the device was intended!

3. Package contents

- DVD-Player

- Infrared remote control

- 2 Batteries for remote control, type AAA/ (Micro cells)

- RGB Scart cable

- Audio/Video RCA Cinch cable

- HDMI cable

- Operating manual

4. Operating components

A. DVD player front panel

Disc tray

Display (with standby LED (green) and IR sensor for remote control)

OPEN/CLOSE button

PLAY/PAUSEbutton

STOP  button

STANDBY button

Headphones output for 3,5 mm jackplug

USB port

Memory card slot for SD/MMC/MS and MSPro cards

B. DVD player rear panel

Power cable

POWER switch

VIDEO: Composite video output

Y, U/Pb, V/Pr: Component video outputs

SCART: Scart/RGB output

FL/FR: Output for front, left and right audio channels

SL/SR: Output for rear, left and right audio channels

SW: Output for bass audio channel

CEN: Output for front and centre audio channels

;

COAXIAL: Coaxial audio output

MIX L/R: Left and right audio outputs

HDMI: HDMI output

OPTICAL: optical digital audio output

S-VIDEO: S-Video output

IB_KH6521_22_33138_39_LB3AB.qxd 23.07.2009 15:12 Uhr Seite 2

- 3 -

C. Remote control

OPEN/CLOSE : Open/Close the disc tray

Number buttons

PLAY/PAUSE : Start/Suspend playback

MUTE : Switch the sound on/off

V-MODE: Set the video output

DIMMER: Adjust the display brightness

DISPLAY: Superimpose disc information

SKIP FWD

VOL +/- : Raise/lower the sound level

SKIP BWD

SUBTITLE: Set the subtitle

ENTER: Confirm input

Control buttons 

MENU/RIPPING: Access disc menu/ripping function

SLOW: Slow motion function

RETURN: Set the playback mode

ZOOM: Set the image enlargement

STOP: Stop playback

;

A-B: Repeat sequence

Battery compartment (on the rear panel)

REPEAT: Set the repeat function

USB: Change between disc playback and USB/card playback

STEP: Individual frame playback

L/R/ST: Set the audio channel

AUDIO: Set the audio language

TITLE: Access the title menu

FAST RWD: Fast search backwards

FAST FWD: Fast search forward

PROG: Access the programme function

PBC: PBC function activate/deactivate (VCD, SVCD only)

ANGLE: Change the camera perspective

SETUP: Access the OSD menu

GOTO:Access titles, chapters and time direct select menus

STANDBY : Switch the device to standby mode

5. Setting up of the DVD player

1. Carefully remove the DVD player and the supplied accessories from

the packing.

2. Remove the protective foil from the display.

3. Place the DVD player on a flat, even and firm base. Do not subject the

device to any external heat or moisture source. Make sure that the device

has sufficient ventilation on all sides. Do not place any television directly

on top of the DVD player.

Attention!

Do not plug the DVD player into an electrical outlet at this time.

Wait until you have connected the DVD player to a television set.

In the event that you wish to change the type of video or audio connection

you must first pull the power plug from the power socket! Otherwise the

DVD player and possibly equipment connected to it could become

irreparably damaged through voltage peak strikes!

6. Safety instructions

• This device is not intended for use by individuals (including children)

with restricted physical, physiological or intellectual abilities or deficiences

in experience and/or knowledge unless they are supervised by a person

responsible for their safety or receive from this person instruction in how

the device is to be used.

• Children should be supervised to ensure that they do not play with the

device.

• To avoid unintentionally switching on the device pull the power cord

from the mains supply after use and before cleaning.

• Check the device and all parts for visible damages. The safety concept

can work only if the device is in a faultless condition.

• The power plug must always be easily accessible, so that the device can

be quickly disconnected from the mains in the event of an emergency.

Risk of electrical shocks!

• Connect the device only to correctly installed and earthed mains sockets.

Ensure that the rating of the local power supply tallies completely with

the details given on the rating plate of the device.

• Arrange for defective power plugs and/or cables to be replaced at

once by qualified technicians or our Customer Service Department.

• Arrange for customer service to repair or replace connecting cables

and/or devices that are not functioning properly or have been damaged.

• Never immerse the device in water. Wipe it only with a slightly damp

cloth.

• Do not expose the device to rain and never use it in a humid or wet

environment.

• Ensure that the power cable never becomes wet during operation.

• You must not open the housing or repair the device yourself.

Should you do so, device safety can no longer be assured and the

warranty will become void.

• Protect the device against drip and spray water. Do not place any

water-filled vessels (e.g. flower vases) on the device.

Risk of fire!

• Do not use the device in the vicinity of hot surfaces.

• Do not locate the device in places exposed to direct sunlight.

If you do, it may overheat and become irreparably damaged.

• Do not leave the device unattended when in use.

• Never cover the ventilation slots of the device while it is being used.

• Do not place any open sources of fire, like candles, on the device.

Injury hazard!

• Keep children away from the connecting cable and the device.

Children frequently underestimate the dangers of electrical equipment.

• Ensure that the device stands with a safe and secure positioning.

• Do not operate the device if it has sustained a fall or is damaged.

Arrange for the device to be checked and/or repaired by qualified

technicians.

• Batteries/ battery cells are potentially fatal if swallowed. Store batteries

out of the reach of children. If a battery is swallowed medical assistance

must be sought immediately.

• Also, store the packaging foils well away from children. There is a risk

of suffocation.

- 4 -

Danger! Laser radiation!

This device is fitted with a „Class 1 Laser“.

• Never open the device.

• Never attempt to repair the device.

• There is invisible laser radiation inside the device.

Do not expose yourself to the laser beam.

Note:

Some aggressive furniture finishes can have a destructive influence on the

device's rubber feet. If necessary, place the device on a nonslip pad.

Thunderstorms!

Equipment connected to a power supply can be damaged during a

thunderstorm. You should therefore always pull the power plug from the

power socket when there is a storm.

Notice regarding electrical power surges

(EFT / electrical fast transient) and electrostatic discharges:

In the case of malfunction due to an electrical fast transient (power surge)

and/or electrostatic discharge, the device must be returned to default

settings in order to re-establish normal operation. The power supply may

have to be disconnected and then reconnected. The batteries (if present)

must be removed and then reinserted.

Notice regarding disconnection from mains-power

The POWER switch does not completely disconnect the device from

the power network. Additionally, the device consumes power when in

standby-mode. To completely disconnect the device from mains-power,

the power plug MUST be removed from the wall socket.

Information regarding the handling of batteries

The remote control is operated by batteries.

For the safe handling of batteries please observe the following safety

information:

Danger exists from uses other than those intended!

• Do not throw the batteries into a fire.

• Do not short circuit the batteries.

• Do not attempt to recharge the batteries.

• Regularly check the condition of the battery. Leaking battery acid can

cause permanent damage to the device. When handling a damaged or

leaking battery special care should be taken. Danger from acid burns!

Wear protective gloves.

• Clean the battery compartment and the battery contacts with a dry cloth.

• Store batteries out of reach of children. When swallowed seek immediate

medical attention.

• Remove the batteries from the device if you do not intend to use the device

for an extended period of time.

• Never open batteries, never solder or weld batteries.

The risk of explosions and injuries exists!

Attention!

No liability/warranty will be considered for damage to the DVD player

caused by the effects of moisture, water penetration or overheating!

7. Remote control

7.1 Inserting the batteries

1. Open the battery compartment on the rear of the remote control.

2. Place the two supplied batteries type AAA (micro cells) into the battery

compartment. Make sure that the batteries are inserted in accordance

with the correct polarity.

3. Replace the battery compartment cover.

7.2 Using the remote control

In order to guarantee faultless operation when using the remote control…

• Always point the remote control, during use, directely at the DVD player

• Make sure that there are no obstructions between the remote control

and the DVD player that will hinder reception.

• When using the remote control place yourself not more than 5 metres

from the DVD player

otherwise interferences can occur during operation of the DVD player functions

with the remote control.

7.3 Replacing the batteries

If the operation of the DVD player via the remote control does not function

properly or does not function at all the batteries must be replaced

• Always renew all batteries in order to return the remote control to its full

performance ability.

8. Connecting the DVD player to a television

After setting up the DVD player, you can now connect it to a television.

The DVD player can be connected to televisions which operate with the PAL

and NTSC standards.

If you want to use the DVD player on a television with the NTSC standard

you must change the video setting in the DVD players "OSD menu". There

PAL is set as the television standard at the factory. Depending on the televisions

equipment there are different methods of connecting the DVD player to it,

these are explained as follows.

• For playback select the matching channel on your television Check with

the television's instruction manual on how you can set the AV channel.

• In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/OFF .

On this subject see also chapter 10 "Settings in the OSD menu".

8.3 Connection to a television via video input

(Composite Video)

For this connection variant the television must be equipped with Audio/Video

cinch sockets (Composite Video).

In order to connect the DVD player to a television via Composite Video you

will need

• an audio/video RCA cinch cable (supplied)

• Connect the yellow marked video socket with the yellow

VIDEO socket on

the television.

• Connect the audio output sockets

MIX L/R on the rear panel of the DVD

player to the corresponding audio inputs on the television. Make sure

that the colour markings yellow, red and white correspond.

• For playback select the matching channel on your television Check with

the television's instruction manual on how you can set the AV channel.

• In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/OFF.

On this subject see also chapter 10 "Settings in the OSD menu".

8.4 Connecting via component signal (YPbPr/YUV)

This connection variant is only possible with very high grade televisions,

LCD/Plasma screens or Video projectors.

Check with the instruction manual of the corresponding playback device to

see if this connections variant is available. It is possible that additional playback

device settings may have to be implemented.

The so called "Component signal" is put out via the YPbPr socket of the DVD

player. Component signals are available in the form of the so called "YUV"

signal (Half image) as well as in the form of the so called "YPbPr" signal

(Full image/Progressive scan).

On this topic, please refer to Section 18. "Glossary / KeyWord Index".

The cable connections are the same in both cases; YPbPr-signal for Progressive

Scan however can only be used if the television (or Video projector), to which

you want to connect the DVD player, is capable of Progressive Scan. If you

are not sure whether the television (or Video projector), to which you want to

connect the DVD player is capable of Progressive Scan and has cinch sockets

available then you can check this by consulting the television's (or Video

projectors's) instruction manual.

For both variations – "YPbPr" and "YUV"– you will need

• an audio cinch cable (not supplied)

• an YUV cable (not supplied) These can be obtained from your dealer.

- 5 -

8.1 Connecting to a television via ScartCable/RGB

Note:

Connecting the DVD player to a television with a Scart cable via the RGB input

offers a high quality connection. Select this connection variation in the case of

televisions equipped with an RGB input. If you are not sure if the television is

equipped with an RGB input then you can check this by consulting the television's

instruction manual.

• Connect the jack inscribed with

SCART to a television Scart socket by

using the supplied Scart cable.

• For playback select the matching channel on your television Check with

the television's instruction manual on how you can set the AV channel.

• In the OSD menu select under the VIDEO/VIDEO OUTPUT/RGB or

OFF menus.

The menu option VIDEO OUTPUT is only selectable when the HDMI output

is deactivated. On this subject see also chapter 10 "Settings in the OSD

menu".

8.2 Connecting to a television via S-Video

Note:

For this type of connection the television must have available an S-VIdeo input

and two audio "IN" cinch sockets. If you are not sure if the television is equipped

with S-Video and/or cinch sockets you can check this by consulting the television's

instruction manual.

For this connection variant you will need:

• an audio cinch cable (not supplied)

• an S-video cable (not supplied) These can be obtained from your dealer.

To connect the DVD player to a television via S-video:

• Connect the jack inscribed with S-VIDEO to a television S-Video socket

using an S-Video cable.

• Connect the audio output sockets

MIX L/R on the rear panel of the DVD

player via an audio cinch cable to the corresponding audio inputs on

the television. Make sure that the red and white colour markings

correspond.

- 6 -

On the rear panel of the DVD player you will find the connection sockets

Y, U/Pb and V/Pr.

Connecting the DVD player via component signal:

• Connect the sockets Y (green), U/Pb (blue) and V/Pr (red) with the corres-

ponding sockets on the television.

• Connect the audio output sockets

MIX L/R on the rear panel of the DVD

player to the corresponding audio inputs on the television with an audio

cinch cable.

Make sure that the red and white colour markings correspond.

• For playback select the matching channel on your television Check with

the television's instruction manual on how you can set the AV channel.

• In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/YUV.

On this subject see also chapter 10 "Settings in the OSD menu".

8.5 Connecting to a television via HDMI

This connection variant is only possible with very high grade televisions,

LCD/Plasma screens or Video projectors

Check with the instruction manual of the corresponding playback device to

see if this connections variant is available. It is possible that additional play-

back device settings may have to be implemented. For this type of connection

you will need the HDMI cable (supplied);

Connecting the DVD player via HDMI:

• Connect the jack inscribed with "HDMI" using a HDMI cable to the

corresponding socket on the television.

• For playback select the matching channel on your television Check with

the television's instruction manual on how you can set the AV channel.

• In the OSD menu select the menu option VIDEO/HDMI Setup/ON.

On this subject see also chapter 10 "Settings in the OSD menu".

9. Connecting audio components to the

DVD player

Besides sound playback of DVDs, VCDs/S-VCDs and audio and MP3-CDs

via the speaker of the television, to which the DVD player is connected,

sound can also be played back via external audio components such as

a HiFi system, Dolby digital/DTS receiver or a surround sound system.

9.1 Requirements for the connection of a HiFi system

In order to enjoy a full sound experience when playing DVDs with the DVD

player you can connect a HiFi system to the player. Before connecting check

with the HiFi system's instruction manual to verify...

• if the HiFi system is suitable for connection to a DVD player.

• if the HiFi system is equipped with cinch sockets; if yes, you can connect

the HiFi system to the DVD player via cinch cables.

Connecting a HiFi system:

• Connect the audio output sockets MIX L/R on the rear panel of the DVD

player to the corresponding audio inputs on the HiFi system with an audio

cinch cable. Make sure that the red and white colour markings correspond.

• Check with the instruction manual which settings on the HiFi system may

be necessary in order to reproduce sound via the HiFi system during the

playback of a DVD, VCD/S-VCD, audio or MP3-CD from the DVD player.

Note:

For an optimal sound experience place your HiFi system's loud speakers to

the left and to the right of the television, on which you connected the DVD

player.

If you connected the DVD player to the television via a Scart cable the audio

signal will be transmitted via the cinch cable to your HiFi system as well as

via the Scart cable to the television. In this case, set the volume of the television

to the lowest value.

9.2 Connecting digital audio components via digital cables

In order to enjoy sound playback throughout the room from correspondingly

equipped DVDs (recognizable by the Dolby Digital or DTS logos), you can

connect the DVD player to a digital audio component, for example, a Dolby

Digital or DTS receiver or a suitable surround sound system.

The cables necessary for the following described connection variations can

be obtained from your dealer.

Firstly check with the digital component’s instruction manual to see if it allows

for connection to the DVD player...

• via a coaxial cable

• or via an optical cable.

- 7 -

Connection via coaxial cable

To connect the DVD player to a digital audio component with a digital coaxial

cable:

• Connect the "COAXIAL" inscribed plug to the corresponding socket on

the digital audio component.

Connecting via optical cable

To connect the DVD player to a digital audio component with an optical cable:

• Remove the protective plug from the "OPTICAL" inscribed socket on the

rear panel of the DVD player and insert the optical cable plug.

• Insert the plug at the other end of the optical cable in the corresponding

socket of the digital audio component.

Note:

The optical cable is a glass fibre cable and must not be bent during installation.

Otherwise the glass fibre contained in the cable could break and the cable

would become unusable.

Note:

Make sure that no dirt can enter into the optical cable socket. This could cause

signal interference. Always insert the protective plug into the socket if no optical

cable is connected.

9.3 Connecting audio components via an analogue cable

If a digital input is not available on the audio component you can connect

the DVD player to it via conventional analogue cinch cables.

To connect the DVD player with analogue cables:

• Plug a cinch cable into each of the sockets

FL (front left channel),

FR (front right channel), SL (rear left channel), SR (rear right channel),

CEN (front centre channel) and SW (Bass) on the rear panel of the DVD player.

• Insert the cinch cables into the corresponding analogue inputs of the

audio component.

9.4 Connecting the headphones

The headphones output is located on the front panel of the DVD player.

• Plug the 3.5 mm headphones jackplug into the headphones output.

Attention!

Listening to music with headphones for long periods and at high

volume levels can lead to hearing damage!

- 8 -

10. OSD menu settings

All of the DVD player's settings can be made with the remote control via

the so called "On Screen Display" menu ("OSD menu" for short). The OSD

Menu will be superimposed on the television screen.

Note:

In these instructions the English OSD menu is described. At any time you can

set the menu to your country's language as described in "GENERAL > OSD

LANGUAGE".

Before you use the DVD player for the first time for playback of DVDs,

VCDs/S-VCDs or audio/MP3-CDs you must implement a few settings via the

OSD Menu. These settings are dependent amongst others on...

• the language, in which you want the OSD menu to be displayed

• which TV standard corresponds to the television, to which you want to

connect the DVD player

• Which image format your television can display

Administering settings via the OSD menu

• First insert the connector plug of the DVD player's power cord into

a power socket.

• To switch the DVD player on activate the

POWER switch on the rear panel

of the DVD player. If the DVD player is already switched on but is in

standby mode, press the button

STANDBY on the remote control to

switch the DVD player on. Standby mode is identified by the green LED

in the display on the front panel of the device.

The device will check to see if a disc is inserted. The SilverCrest logo appears

on the television screen:

If no disc is inserted the notification NO DISC appears on the television

screen and in the display.

• Firstly please familiarize yourself with the OSD Menu's operation by

means of the following brief introduction.

10.1 Using the OSD Menu

• To access the DVD players OSD menu press the SETUP button on the remote

control. The OSD Menu with its menu options will appear on the television

screen:

The following menu options can be selected:

GENERAL, AUDIO, DOLBY, VIDEO and PREFERENCE.

• With the control buttons

 and the ENTER button you can carry

out all the settings in the menu.

• With the control buttons  you can select a menu by moving the yellow

marking onto the corresponding menu symbol.

• With the control buttons  you select an input in a menu by moving

the green bar over an input.

• With the control button you change an input in the sub menu and with

the control button  you move back to the previous menu level.

• To confirm a selection press the

ENTER button.

All navigation possibilities in a current menu are displayed at the lower

edge of the menu.

• To exit the OSD menu press the

SETUP button again.

10.2 Setup menu GENERAL

In this menu you can, for example, set the image presentation or the language

of the OSD menu.

TV DISPLAY

Note:

The menu option TV DISPLAY is only selectable when the HDMI output

is deactivated.

-4:3/PANSCAN Select this setting to display broadcasts in the usual 4:3

format on a 4:3 television set. Broadcasts in the 16:9 format

will be displayed in full screen without the distracting bars

although the side edges of the image will be trimmed.

-4:3/LETTERBOX Display of a film in 16:9 format on a traditional 4:3 format

television. The image is displayed with black bars on the

lower and upper edges of the screen.

-16:9 This setting is recommended when using a wide screen

television in 16:9 format. An image in 4:3 format will be

adapted horizontally to the image width.

-Wide Squeeze An image in 4:3 format will be presented with black bars

on the right and left edges.

-3D SURROUND Select this setting to produce a virtual surround effect from

a stereo or multi channel sound.

-5.1 CH Select this setting to activate the analogue 5.1 outputs.

FRONT SPEAKER, CENTER SPEAKER, REAR SPEAKER and SUBWOOFER

In these menu inputs you can activate/deactivate the individual speaker types

and set the size.

-Large Select this setting if the diameter of the speaker membrane

is greater than 12 cm.

-Small Select this setting for smaller speakers.

-OFF Deactivate sound output for these types of speakers

Note:

The menu input FRONT SPEAKER can not be deactivated since the sound

output for the front speakers always remains switched on.

DIALOG In this menu input you can set the dialogue volume (0-20).

D.R.C. (Dynamic Range Control)

-ON Function activated

-OFF Function deactivated.

-AUTO Function (if available) is automatically activated

DIGITAL AUDIO

DIGITAL OUTPUT

In this menu input you can set the SPDIF output signal.

-SPDIF / OFF No digital audio signal is being put out at the sockets

COAXIAL or OPTICAL.

-SPDIF / RAW The crude data of the Dolby Digital sound is put out.

-SPDIF /PCM Select the setting PCM (Pulse Code Modulation) when there

is a connection to a digital amplifier/receiver. Your DVD

player transmits, through the PCM signal, the same audio

formats that are rendered on the disc. In addition an audio

signal will be put out via the sockets

FL and FR.

LPCM OUTPUT Select this input to set the sampling frequency for the

processing of the crude data.

-48K: Default setting.

-96K: Only for DVDs with the corresponding sampling frequency.

Note:

The LPCM OUTPUT function is only available if you have set the SPDIF audio

output signal to PCM.

CHANNEL DELAY

Select this menu input to set the channel delay of the individual speakers.

With optimal settings the sound reaches your ears simultaneously from all

directions.

With the control button  go to the graphics field beside the input.

With the control buttons  or  select the speaker.

With the control buttons  you increase/decrease the value in increments

of 10 cm. The maximum setable deviation for the CENTER speaker is 170 cm.

The maximum setable deviation for the SUBWOOFER and the rear speakers

is 510 cm.

Confirm your entry by pressing the

ENTER button.

Note:

The channel delay is determined by the front speakers therefore these are not

selectable.

- 9 -

ANGLE MARK

-ON If scenes are recorded on a DVD in different perspectives

this will automatically be signified by a camera symbol

displayed on the television screen. Press the

ANGLE button

on the remote control to display the various perspectives.

-OFF Deactivate function. No symbol appears on the television

screen.

OSD LANGUAGE

Here you set the language, in which the OSD Menu will be shown on the

display.

CLOSED CAPTIONS

-ON Select this setting if by every playback of a DVD the subtitle

(if present) is to be automatically displayed on the television

screen.

-OFF Select this setting to manually activate the subtitle.

The subtitles can also be set, during playback, with the

SUBTITLE button.

SCREEN SAVER

-ON Screen saver activated. The screen saver will now switch

on when the playback is stopped and no activity takes

place for several minutes.

-OFF Deactivate function.

LAST MEMORY

-ON Select this setting to playback a disc from the previously

halted position after removal and re-insertion.

-OFF Deactivate function. The disc playback starts back at the

begining after removing and then reinserting.

Note:

If the DVD player is turned off with the POWER switch the saved position will not

be preserved.

10.3 Setup menu AUDIO

In this OSD menu you can, for example, carry out settings for the analogue

as well as the digital audio outputs.

ANALOG AUDIO

DOWNMIX

If you use the analogue 5.1 output in this menu you can carry out the

appropriate settings.

-LT/RT Only the left and right channels at the sockets

FL and FR

will put out signals.

-STEREO A stereo sound will be put out. Select this setting if you are

not using the analogue 5.1 outputs. The menu options

CENTER SPEAKER and REAR SPEAKER are then not requi-

red and therefore inactive.

- 10 -

EQUALIZER

-SOUND MODE Select this menu input if, when playing back sound, you

want to use one of the preset equalizer levels ROCK, POP,

LIVE, DANCE, TECHNO, CLASSIC or SOFT. To deactivate

this function select the input OFF.

-BASS BOOST Select the setting ON if you want to boost the playback of

the base tone. To deactivate this function select the input OFF.

-SUPER BASS Select the setting ON to use the super base sound effect.

In addition playback of the base tone will be boosted.

To deactivate this function select the input OFF.

-TREBLE BOOST Select the setting ON if you want to boost playback of the

treble sounds. To deactivate this function select the input OFF.

3D PROCESSING

Select this menu input if you want to activate/deactivate the Pro Logic II process.

Note:

The menu option PRO LOGIC II can only be selected if the analogue

5.1 outputs are activated.

-PRO LOGIC II Select the setting ON if the process is to be activated all

the time.

Select the setting AUTO if the process is only to be activated

when Dolby Pro Logic II encoded content is located on the

playback medium.

To deactivate this function select the input OFF.

-MODE In this menu you can set the Pro Logic II

process mode.

MUSIC: Sound is played back through the speakers

without delay.

MOVIE: Sound is played back with a delay of 10 ms

through the rear speakers.

PRO

LOGIC: Earlier version of the DOLBY PRO LOGIC processes.

AUTO: Automatic setting of the processes (depending on

the contents of the playback medium).

Note:

The menu inputs PANORAMA, DIMENSION and CENTER WIDTH serve to

fine tune the sound and are only available if you have set the process mode

MUSIC.

-PANORAMA Select the setting ON to activate this sound enhancement.

To deactivate this function select the input OFF.

-DIMENSION Select one of the settings SIZE -3 to SIZE 3 to activate this

sound enhancement.

-CENTER WIDTH Select one of the settings LEVEL 0-7 to receive a corresponding

sound enhancement.

REVERB MODE Select this menu input if you want to use, for sound playback,

one of the preset reverbs CONCERT, LIVING ROOM, HALL,

BATHROOM, CAVE, ARENA, or CHURCH. To deactivate

this function select the input OFF.

10.4 Setup menu DOLBY

In this OSD menu you can carry out settings for the Dolby-Digital output.

DUAL MONO Select this menu input to set the Dolby-Digital output to either

STEREO, L-MONO, R-MONO or MIX-MONO.

DYNAMIC Select this menu input to enable an optimal sound playback

with reduced volume. In the setting FULL the louder passages

will be surpressed and the softer passages will be played

back louder.

Note:

This function is only possible when using a digital audio component.

10.5 Setup menu VIDEO

In this menu you can, for example, carry out settings for the video output,

resolution or colour.

VIDEO OUTPUT

-OFF The video signal will be put out via the S-video output and

the composite video output.

-YUV The video signal will be put out in YUV colour format via

the component video outputs Y, U/Pb, V/Pr.

-RGB The video signal will be put out in RGB colour format via

the SCART connection.

Note:

This setting is only active if the HDMI setup is deactivated.

The composite video output on the DVD player is always activated. If the selected

setting deviates from the actual connection variation (apart from composite video)

it is possible that no image or a poor image will be displayed on the television

screen. In this event press, when playback is stopped, several times the

V-MODE

button on the remote control until the image is displayed properly.

- 11 -

RESOLUTION In this menu input you can set the different resolutions

(480i/576i/720p/1080i/1080p

)

for the HDMI

output/component video output.

Note:

Be aware that for the TV standard PAL a setting with 50 Hz and for the TV

standard NTSC a setting with 60 Hz must be selected.

COLOR SETTING

In this menu input you can implement the settings, for example, for the brightness,

contrast or hue.

-SHARPNESS Select this menu input to set one of the predefined sharpness

values (HIGH, MEDIUM or LOW).

-BRIGHTNESS With the help of the control buttons

set the brightness

from -20 to +20. Subsequently press the

ENTER button to

continue.

-CONTRAST With the help of the control buttons

set the contrast

from -16 to +16. Subsequently press the

ENTER button to

continue.

-GAMMA Select this menu to set one of the predefined gamma values

(HIGH, MEDIUM, LOW or NONE).

-HUE With the help of the control buttons

set the hue from -

9 to +9. Subsequently press the

ENTER button to continue.

-SATURATION With the help of the control buttons

set the saturation

level from -9 to +9. Subsequently press the

ENTER button to

continue.

-LUMA DELAY Select this menu input to set one of the predefined gamma

values (0 T or 1 T).

HDMI Setup

-ON Select this menu input to activate the HDMI output.

-OFF Select this menu input to deactivate the HDMI output.

Xvid SUBTITLE In this menu input you can set the Xvid subtitle language

that is to be the standard used when playing back films.

10.6 Setup menu PREFERENCE

In this menu you can, for example, carry out the settings for the video output,

activate/deactivate the child lock or change the password.

Note:

The menu option PREFERENCE is only selectable when playback is

completely finished.

TV TYPE

-PAL PAL television standard

-NTSC NTSC television standard.

AUDIO In this menu input you can set the language that is to be

the standard used when playing back films.

SUBTITLE In this menu input you can set the subtitle language that is

to be the standard used when playing back films.

DISC MENU In this menu input you can set the disc menu language that

is to be the standard used when playing back films.

PARENTAL In this menu input you can determine the age restrictions.

Note:

Only a few DVDs have a technical age restriction available. If there is no technical

age restriction on the DVD your DVD players child lock feature can not

be activated. The child lock can only function if it is activated on the DVD player

and a corresponding code is available on the inserted DVD.

If you insert a DVD which, according to the child lock, may not be played back

a window appears on the screen, in which you must enter your password and

confirm with

ENTER. Some DVDs and CDs are encoded with encryption signals.

In this way DVDs can be divided into eight different approval classes.

Select one of the following approval classes to protect the playback of

this media class with a password request:

1 KID SAFE: also suitable for young children

2 G: for all age groups

3 PG: adult supervision recommended;

4 PG 13: adult supervision strongly recommended; some scenes are

not suitable for children under 12

5 PGR: for children under 16; adult supervision recommended

6 R: for children under 16; adult supervision strongly recommended

7 NC 17: not for teenagers under 18 years of age

8 ADULT: for adults only

Example

If a DVD was encoded with, for example, approval class 7 or 8 and you have

an approval class setting between 1 and 6 then a message follows and the

password must be entered. Also only parts of the DVD, that is to say certain

film scenes, may be encoded with an approval class or various approval classes.

• To activate the approval class you must select, in the PARENTAL menu,

the desired approval class and enter the password (136900).

Confirm your entry by pressing the

ENTER button.

PASSWORD In this menu input you can change the factory default

password (136900) and assign your own password.

Only the numbers 0-9 can be used.

Note:

In the event that you forget your new password you can use the factory preset

password (136900).

DEFAULT In this menu input you can restore the DVD players factory

defaults.

- 12 -

11. Initial operation of the DVD player

After you have …

• placed the DVD player in a suitable location

• connected the DVD player to a television by one of the designated

connection options

• connected the DVD player, if desired, to a HiFi or Surround system

(analogue/digital) for example a Dolby Digital or DTS receiver

• made the remote control ready for operation by inserting the batteries

• and know how to activate and operate the OSD menu with the remote

control

… the DVD player is ready for operation.

11.1 Inserting the DVD

To play a disc with the DVD player:

• Switch on your television.

• Make sure that the DVD player is ready for operation.

If the television, the DVD player and possibly other connected devices (i.e. an

audio component) are ready for operation and are switched on and the DVD

player is connected correctly to the television you will now see the Silvercrest

logo on the TV screen

If no disc is inserted into the DVD player's disc tray:

The message NO DISC is displayed on the television screen.

• Open the disc tray by pressing the button

OPEN/CLOSE on the remote con-

trol or on the front panel of the DVD player. OPEN is displayed on the

television screen.

• Insert the disc in the disc tray with the inscribed/labled side up.

For two-sided discs: The side you would like to play must face down.

• After you have inserted the disc press the button

OPEN/CLOSE on the re-

mote control or on the front panel of the DVD player again to close the

disc tray.

• The contents of the disc will now be loaded; this may take a few seconds.

In the meantime LOADING is displayed on the television screen.

11.2 Inserting memory cards/USB memory sticks with

MP3/WMA/ MPEG4/JPEG data.

Note:

The DVD-Player always starts in DVD mode. To read memory cards/USB memory

sticks press the

USB button on the remote control. The DVD player recognizes

the data formats JPEG, MP3, WMA and MPEG4.

In order to insert memory cards of the types SD, MS/MSPro and MMC into

the DVD player:

• Switch on your television.

• Make sure that the DVD player is ready for operation.

If the television, the DVD player and possibly other connected devices (i.e. an

audio component) are ready for operation and are switched on and the DVD

player is connected correctly to the television you will now see the Silvercrest

logo on the TV screen

If no disc is inserted into the DVD player's disc tray: The message NO DISC is

displayed on the television screen.

• Slide the memory card into the memory card slot.

Then proceed with the following steps depending on the type of memory

card that you want the device to read.

Warning!

Always make sure that you insert memory cards into the memory card slot as

described hereafter! Under no circumstances bend or buckle the memory

card when inserting into the memory card slot! Slide the memory card up to

the stop in the memory card slot, with a light pressure.

Allow the memory card to slide in without force:

• Check to make sure that the memory card is one that the DVD player is

capable of reading.

Do not attempt to insert memory cards of another type in the memory

card slot!

• Make sure that you have inserted the memory card into the memory

card slot in the correct manner.

• Under no circumstances attempt to force the memory card into the memory

card slot!

Otherwise the DVD player, memory card and the data on the memory card

could be damaged!

Supported memory card types and capacities

Memory cards of the types SD (2 GB not SDHC), MS/MSPro (4 GB), MMC

(4 GB) can be played back.

Note:

Your DVD player can only read storage mediums with several data formats if

each folder contains only one data format.

MultiMediaCard- /SecureDigital memory cards (MMC/SD)

Insert the MMC/SD memory cards with the contacts forward and slide them

straight into the memory card slot.

With this the side of the memory card, on which the contacts are located

must face downwards with the chamfered corner facing to the right.

MemoryStick/memory cards (MS/MSPro)

Slide the MS memory card into the memory card slot, level and with the

contacts facing forward.

With this the side of the memory card, on which the contacts are located

must face downwards with the chamfered corner facing to the left.

- 13 -

USB memory sticks (USB)

The DVD player supports USB memory sticks 1.1 and 2.0 up to a capacity

of 4GB.

USB memory sticks must be inserted into the USB port.

• Press the

USB button on the remote control. If several memory mediums

(USB and memory card) are inserted press, repeatedly, the USB button

until the contents of the USB memory stick is displayed. This procedure

also applies to particular memory cards.

11.3 Removing memory cards/USB memory sticks

Memory cards/USB Memory sticks should only be removed after the memory

card slot is deactivated. Thus avoiding the possibility of damage or data loss.

• Press the

USB button on the remote control to return to the DVD mode.

For this a disc must be inserted into the DVD player.

• You can now remove the memory card/USB memory stick from the memory

card slot/USB port.

12. Playing back DVDs, VCDs or S-VCDs

To play back a DVD/VCD/S-VCD with the DVD player...

• Switch on your television.

• Make sure that the DVD player is ready for operation.

If the television, the DVD player and possibly other connected devices (i.e. an

audio component) are ready for operation and are switched on and the DVD

player is connected correctly to the television you will now see the "Silvercrest"

logo on the TV screen

• Open the disc tray on the front panel of the DVD player by pressing the

OPEN/CLOSE button.

OOPPEENN

now appears in the display on the front panel of the DVD player and

on the television screen.

• Insert a DVD/VCD/S-VCD disc in the disc tray with the inscribed/labled

side up.

• Press the

OPEN/CLOSE button again to close the disc tray.

CLOSE will appear in the display on the front panel of the DVD player and

on the television screen while the disc tray is closing.

• The contents of the inserted DVD/VCD/S-VCD will now be loaded; this

may take a few seconds. In the meantime LOADING blinks in the display

on the front panel of the DVD player and on the television screen.

• Playback of the inserted DVD/VCD/S-VCD starts automatically.

Note:

DVDs, VCDs and S-VCDs that you want to playback with the DVD player

may possibly have a country code which is printed on the DVD's jacket.

The DVD player can only playback DVDs/VCDs/S-VCDs with the country code .

If no country code is printed on the cover of a DVD/VCD/S-VCD...

• but instead the symbol , then the DVD/VCD/S-VCD can be

played back with the DVD player

• then the DVD/VCD/S-VCD can possibly not be played back with the

DVD player. You can check this by attempting to play back the DVD.

Depending on the inserted DVD/VCD/S-VCD it is possible that the contents

of the DVD/VCD/S-VCD will not playback immediately, rather first a selection

menu appears on the television screen.

In this event select the menu option, which will start the playback of the film,

with the control buttons on the remote control.

• To start playback of the film press the

ENTER button on the remote control

or press the

PLAY/PAUSEbutton.

- 14 -

In the display on the front panel of the DVD player, the following notices

appear:

With DVDs:

•"DVD"

• the number of the currently playing chapter

• the played back so far time of the currently playing DVD in minutes and

seconds

With VCDs/S-VCDs:

• "VCD" or "S-VCD"

• the number of the currently playing title

• the played back so far time of the currently playing VCD/S-VCD in

minutes and seconds

12.1Features during playback of a DVD, VCD or S-VCD

During the playback of a DVD/VCD/S-VCD you can use the following DVD

player features...

Pause playback

To pause the playback of the inserted DVD/VCD/S-VCD...

• During playback press the

PLAY/PAUSEbutton

 will now appear in the display on the front panel of the DVD player and

on the television screen.

On the television screen you will see a freeze frame of the scene that has just

been halted.

• To contnue playback of the film press the

PLAY/PAUSEbutton.

Stop playback (STOP)

To stop playback of the film on the inserted DVD/VCD/S-VCD press the

STOP button.

With resume function

If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing

the

STOP button once the DVD player automatically saves the position

where playback was interrupted. This function is called the "resume function".

PRESS PLAY KEY TO CONTINUE appears on the television screen. As

soon as you press the

PLAY/PAUSEbutton again playback will continue

from the saved position.

Without resume function

If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing

the

STOP button once and you press the STOP button a second time the

saved position, at which you interrupted the playback, will be cleared.

When you press the

PLAY/PAUSEbutton again playback of the inserted

DVD/VCD/S-VCD starts from the beginning.

Access the DVD menu (MENU)

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

With many films on DVDs there is a main menu on the disc which, apart from

the option of playing back the main film, allows you to select from the following

contents:

• the subtitle and film dialogue languages

• direct chapter selection

• to playback the films bonus material (Background information,

"Making of" etc.)

If such a menu is present on the DVD inserted in the DVD player you can access

it during playback by pressing the

MENU button on the remote control.

You can select particular menu options by pressing the control buttons

on the remote control.

To confirm the selected menu option press the

PLAY/PAUSEbutton or the

ENTER button on the remote control.

To return to playback press the

MENU button on the remote control again.

Note:

If you cancel playback by pressing the STOP button twice (Playback stop without

resume function) access to the disc's main menu is no longer possible.

Playback Control (PBC) with VCDs/S-VCDs

Many VCDs/S-VCDs have Playback Control (in short "PBC"). Playback Control

indicates a main menu that allows operation of several functions of the

VCD/S-VCD.

If PCB is available on a VCD/S-VCD inserted in the DVD player you must first

activate it in order to be able to superimpose the menu.

• During playback or when playback is stopped press the

MENU button.

The message PBC: OFF appears in the display.

• Press the

MENU button again. The message PBC: ON appears in the display.

PBC is now switched on the discs main menu can be accessed with the

MENU or TITLE buttons.

Note:

If you switch on PBC during playback then it is possible that playback will

stop and start again from the beginning and/or with the main menu.

Skip to start of chapter (Skip)

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

With the buttons

SKIP FWD and SKIP BWD you can, during playback,

within the film on the inserted DVD/VCD/S-VCD …

• skip forward to the beginning of the next chapter or

• skip backward to the preceeding chapter

The respectively selected chapter will playback immediately without having

to press the

PLAY/PAUSE button. The number of the respectively selected

chapter will be displayed on the front panel of the DVD player to the left of

the played back so far time.

- 15 -

Title number input via the number buttons

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

Instead of using the Skip function you can also enter the title from within the

film on the inserted DVD/VCD/S-VCD direct by entering the title number via

the number buttons on the remote control.

• For this, during playback or when playback is stopped, press the number

buttons on the remote control corresponding to the title number, for

example, the

3 button for the third title.

• Playback of the entered title number will now start automatically.

Direct chapter or time selection via the Search function (GOTO)

Note:

This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt

to carry out functions that are not available the symbol will be displayed

on the television screen.

Entry of the time position via search function DVD, VCD and SVCD:

• During playback press the GOTO button on the remote control. The time

menu is superimposed on the television screen:

• The entry field TITLE is automatically selected first. Press the

ENTER button

and enter, with the number buttons, the desired title. On DVDs title 01 is

most often the main film.

• Press the navigation button  to select the entry field

CHAPTER. Press the

ENTER button and enter, with the number buttons, the desired chapter.

• Press the navigation button  to select the entry field AUDIO. Press the

ENTER button and select, with the navigation buttons , an audio language.

• Press the navigation button  to select the entry field SUBTITLE. Press the

ENTER button and select, with the navigation buttons , a subtitle language.

• Press the navigation button  to select the entry field ANGLE. Press the

ENTER button and select, with the navigation buttons , another camera

perspective (if available).

• Press the navigation button  to select the entry field TT TIME. Press the

ENTER button and enter, with the number buttons, the desired title time.

• Press the navigation button  to select the entry field CH TIME. Press the

ENTER button and enter, with the number buttons, the desired chapter time.

• Press the navigation button  to select the entry field REPEAT. Press the

ENTER button and select, with the navigation buttons , a repeat function

(see also repeat functions).

• Press the navigation button  to select the entry field TIME DISP. Press

the

ENTER button and select, with the navigation buttons , a time

presentation (see also superimpose disc information).

• To fade the menu out press the

GOTO button again.

Audio CD

• During playback press repeatedly the GOTO button on the remote control.

The following notices appear, one after the other, in which you can enter

a time position with the number buttons:

DISC GOTO: Enter here a time position on the disc from where playback

should start.

TRACK GOTO: Enter here a time position for the currently playing back

title from where playback should start.

GOTO TRACK: Enter here a title number from where playback should start.

MPEG CD

SELECT: Enter here a title number on the disc from where playback

should start.

GOTO: Enter here a time position for the currently playing back

title from where playback should start.

Fast scan forward/backward

With fast scan you can select designated passages from the inserted

DVD/VCD/S-VCD during playback.

• For fast scan forwards/backwards press the 

FAST FWD and/or  FAST RWD

button repeatedly to set the following fast scan speeds:

Note:

During fast scan no sound will be played back.

• To continue playback of the film at the selected place in normal

speed press, during fast scan the

PLAY/PAUSE button.

Slow playback forward (Slow motion)

To playback the contents of the inserted DVD/VCD/S-VCD in slow motion …

• For slow playback forwards press the

SLOW button repeatedly to set the

following playback speeds:

Note:

During slow motion playback no sound will be played.

• To continue playback from a selected position in normal speed, during

slow motion playback press the

PLAY/PAUSE button.

- 16 -

Image enlargement (Zoom)

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

During the playback of an inserted DVD/VCD/S-VCD you can enlarge the

image on the television screen in three levels. For this press the

ZOOM button

on the remote control to set the following enlargement levels:

With the control buttons sections of the enlargement can be

suspended.

To switch off the enlargement function and return to the normal image

size press repeatedly the

ZOOM button.

Change camera aspect (Angle)

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

Many films on DVD/VCD/S-VCD contain chapters which were recorded

simultaneously from various camera perspectives. With films that have such

chapters available you can view the same chapter from different perspectives.

For this press the

ANGLE button on the remote control during playback of an in-

serted DVD/VCD/S-VCD. Each press of the

ANGLE button will switch to one of

the available camera perspectives.

Superimpose/fade out subtitles

Note:

This function may not be available on all DVDs! If you attempt to execute

a function that is not available, the symbol is displayed on the television

screen.

If the film on the inserted DVD/VCD/S-VCD has subtitles available you can

superimpose these on the television screen during playback by pressing the

SUBTITLE button on the remote control.

With the first press of the SUBTITLE button the subtitle of the first available

language will be superimposed on the television screen. With each further

press of the SUBTITLE button the subtitles of other available languages will be

superimposed successively on the television screen.

The number of the currently superimposed subtitle language will be superimposed

on the television screen ( i.e. 1/10 for the first of ten available subtitle languages).

When the last of the available subtitle languages is superimposed (i.e. 10/10

for the tenth of ten available subtitle languages) you can switch off the subtitle

function by pressing the

SUBTITLE button again. OFF is superimposed on the te-

levision screen.

Change playback language

Note:

This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt

to execute a function that is not available, the symbol is displayed on the

television screen.

With many films on DVD/VCD/S-VCD you can, during playback, select another

playback language by pressing the

AUDIO button on the remote control.

The first press of the

AUDIO button switches to the first available playback language.

With each further press of the

AUDIO button other available playback languages,

one after the other, are switched on.

The currently switched on playback language will be superimposed on the

television screen.

- 17 -

Programmed playback (PROG)

Note:

This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt

to execute a function that is not available, the symbol is displayed on the

television screen.

With the "Programme" function you can put together your own film programme

in so far as you can select only certain chapters of an inserted DVD/VCD/S-VCD

for playback. In this way you can determine for yourself the sequence, in which

the chapters are played back. You can compile a maximum of 20 chapters

of a film for programmed play.

• Press the

PROG button on the remote control during playback or when

playback is stopped.

The Programme menu will be displayed on the television screen.

Programme window

First are listed the programme positions 1-10, programme position 1 is

highlighted.

1. With the number buttons enter the number of the title that is to be played

back first. The highlight changes to chapter entry (CH:).

2. With the number buttons enter the number of the chapter that is to be

played back. The highlighting moves to the programme position 2.

3. Select, with the navigation buttons , further programme positions

and enter title and chapter numbers for the programme positions.

• To display the next 10 programme positions select, with the navigation

buttons , the field  and press the

ENTER button.

You can allocate up to 20 programme positions.

• To delete entries in a programme position select the programme position

and press the

ENTER button.

• To stop the programme function select the field EXIT and press the

ENTER

button. All allocated programme positions are deleted.

4. You start playback of the programme positions by selecting the field

START and press the

ENTER button.

During the programmed playback the notice PROGRAM appears in the display.

To delete the programmed playback press twice, during playback, the

STOP

button on the front panel of the DVD player or on the remote control.

Note:

If you are not sure what number a title and/or chapter to be programmed has

then select the corresponding chapter, during playback of the film, with the

buttons

SKIP FWD and SKIP BWD and susequently press the DISPLAY button

on the remote control to superimpose all information from the inserted DVD/VCD/

S-VCD onto the television screen. Here you will find, amongst others, the current

title and chapter numbers.

On this topic see also the section "Superimpose disc information".

Superimpose disc information

Note:

This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt

to execute a function that is not available, the symbol is displayed on the

television screen.

With this function you can superimpose all the available information from

a DVD/VCD/S-VCD inserted into the DVD player onto the television screen

during playback.

• For this, during playback, press the

DISPLAY button on the remote control.

On the television screen will be superimposed:

With DVDs:

• the current title number/the total number of titles

• the current chapter number/the total number of chapters

• the played back so far time in hours, minutes and seconds (TITLE ELAPSED)

• the time to the end of the film in hours, seconds and minutes (TITLE REMAIN)

• the played back so far time of the chapter in hours, minutes and seconds

(CHAPTER ELAPSED)

• the time to the end of the chapter in hours, seconds and minutes

(CHAPTER REMAIN)

With VCDs/S-VCDs:

• the current title number/the total number of titles

• the played so far time of the current playback title on the VCD/SVCD in

hours, minutes and seconds (SINGLE ELAPSED)

• the time to the end of the current playback title in hours, seconds and minutes

(SINGLE REMAIN)

To stop display of the disc information press repeatedly the

DISPLAY button

until the notice DISPLAY OFF appears on the television screen.

Repeat function for DVDs, VCDs, S-VCDs and audio CDs

With the repeat function you can…

... in the case of DVDs, selectively repeat title, chapter or the entire DVD.

... in the case of VCDs/S-VCDs individual titles and/or the entire VCD/S-VCD

repeatedly playback.

... in the case of audio CDs, playback repeatedly a particular track and/or

the entire CD.

To switch on repeat playback...

• Press the

REPEAT button several times during playback.

The repeat symbol appears in the display with one of the following

notifications:

CHAPTER Select CHAPTER to continuously repeat the currently playing

back chapter until repeat playback is switched off or play-

back is cancelled by pressing the

STOP  button twice.

TITLE Select TITLE to continuously repeat the currently playing

back title until repeat playback is switched off or playback

is cancelled by pressing the

STOP  button twice.

ALL Select ALL to continuously repeat all available titles on the

disc, thus the entire disc, until playback repeat is switched

off or playback is cancelled by pressing the

STOP button

twice.

To switch off repeat playback press the

REPEAT button repeatedly, during play-

back, until no more notifications appear on the television screen.

- 18 -

Repeat function with MP3/WMA/MPEG/ JPEG/Xvid discs

During playback press the REPEAT button several times to apply the following

repeat functions (the set function appears in the display):

RANDOM

Random playback of the titles on the disc and/or the data carrier.

SINGLE

One time playback of the current title/image.

REPEAT ONE

Endless repeat of the current title/image.

REPEAT FOLDER

Repeat the current folder.

REPEAT ALL

Repeat all titles on the disc and/or data carrier.

Repeat sequence (A–B)

With this function you can repeat playback of a favourite sequence within

a chapter of the current playback disc.

To do this …

• During playback press the A – B button on the remote control as soon as the

desired sequence starts to playback. A appears on the television screen.

• Press the A – B button again as soon as the end of the desired sequence is

played back. Pay careful attention to the fact that the start and finish of

the sequence must be located within a chapter.

AB appears on the television screen.

Repeat playback of the selected sequence begins immediately without you

having to press the

PLAY/PAUSE button. The sequence will continuously re-

peat until you press the A – B button again in order to switch off the function.

Setting playback volume

Press the VOL + button on the remote control during playback to increase play-

back volume or the

VOL – button to reduce playback volume.

Dimmer

Press the DIMMER button on the remote control to change the DVD player's

display brightness in three levels.

To switch playback sound to mute (MUTE)

To switch the playback sound to mute press the (MUTE) button on the remote

control during playback of DVDs, VCDs/S-VCDs, audio CDs and CD-Rs/CD-RWs

with MP3 or WMA data. MUTE is displayed on the television screen.

When you want to switch the playback sound back on press the (

MUTE) button

again or the

VOL + and VOL – buttons. MUTE OFF or the corresponding volume

level is displayed on the television screen.

Switching off the DVD player

To switch off the DVD player:

• In the event that a disc inserted into the DVD player is playing back, first

cancel playback by pressing the

STOP button on the front panel of the

DVD player or on the remote control twice.

• Open the disc tray to remove a currently inserted disc from the DVD

player by pressing the

OPEN/CLOSE button on the front panel of the

DVD player or on the remote control. Subsequently close the disc tray

by pressing the

OPEN/CLOSE button again.

• Press the

STANDBY button on the remote control. The DVD player now

switches to the

STANDBY mode. To switch the DVD player back on press

the

STANDBY button again.

• To switch the DVD player off completely activate the

POWER switch on

the rear panel of the DVD player.

13. Playback of JPEG-Photo

CD/WMA/MP3/MPEG4

Insert a storage medium into the DVD player. If you use a memory card or

USB stick press repeatedly the

USB button until the desired playback source

is depicted.

The contents of the data carrier (CD, DVD, USB memory stick or memory card)

will be displayed on the television:

Display of MP3 data

Display of JPEG data

Display of AVI and MPEG data

• The data is listed on the left (Data window). Folders will be depicted with

the symbol .

Leht laadib ...

Silvercrest KH 6522 Operating Instructions Manual

Bränd: Silvercrest

Mudel: KH 6522

Kategooria: DVD-mängijad

Tüüp: Operating Instructions Manual

See käsiraamat sobib ka

KH 6521

Laadige alla PDF

aruanne

teistes keeltes

svenska: Silvercrest KH 6522

Silvercrest KH 6522 Operating Instructions Manual

See käsiraamat sobib ka

Silvercrest KH 6522 Operating Instructions Manual

teistes keeltes

Seotud paberid

Muud dokumendid