Abit IB9 Omaniku manuaal

Bränd: Abit

Mudel: IB9

Kategooria: Emaplaadid

Tüüp: Omaniku manuaal

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IB9

Motherboard

Socket 775

Intel Core 2 Duo,

Pentium Extreme Editon,

Pentium D, Pentium 4

 Intel P965 / ICH8

 FSB1066

 Dual DDR2 800

 PCI Express

 Gigabit LAN

 4x SATA 3Gb/s

 7.1 Channel HD Audio

ii IB9

IB9

User’s Manual

English + Multilingual QIG

Edition, October 2006

The information in this document is subject to change without notice and does not represent a

commitment on part of the vendor, who assumes no liability or responsibility for any errors that may

appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality,

accuracy or fitness for any particular part of this document. In no event shall the manufacturer be

liable for direct, indirect, special, incidental or consequential damages arising from any defect or

error in this manual or product.

Product names appearing in this manual are for identification purpose only and trademarks and

product names or brand names appearing in this document are the property of their respective

owners.

No part of this manual may be reproduced, transmitted or transcribed without the expressed written

permission of the manufacturer and authors of this manual.

If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail,

we cannot guarantee any responsibility.

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IB9 iii

Contents

1. Hardware Setup ............................................................... 1-1

1.1 Specifications ..............................................................................1-1

1.2 Motherboard Layout.....................................................................1-2

1.3 Choosing a Computer Chassis.......................................................1-3

1.4 Installing Motherboard.................................................................1-3

1.5 Checking Jumper Settings ............................................................1-4

1.5.1 CMOS Memory Clearing Header and Backup Battery ..............1-4

1.5.2 Wake-up Header .................................................................1-6

1.6 Connecting Chassis Components...................................................1-7

1.6.1 ATX Power Connectors ........................................................1-7

1.6.2 Front Panel Switches & Indicators Headers............................1-8

1.6.3 FAN Power Connectors ........................................................1-9

1.7 Installing Hardware....................................................................1-10

1.7.1 CPU Socket 775 ................................................................1-10

1.7.2 DDR2 Memory Slots ..........................................................1-12

1.8 Connecting Peripheral Devices ....................................................1-13

1.8.1 Floppy and IDE Disk Drive Connectors ................................1-13

1.8.2 Serial ATA Connectors .......................................................1-14

1.8.3 Additional USB 2.0 Port Headers.........................................1-15

1.8.4 Internal Audio Connectors..................................................1-16

1.8.5 Front Panel Audio Connection Header.................................1-16

1.8.6 PCI and PCI Express X16, X1 Slots .....................................1-18

1.9 Onboard Status Display..............................................................1-19

1.9.1 Power Source Indicators ....................................................1-19

1.10 Connecting Rear Panel I/O Devices ...........................................1-20

2. BIOS Setup....................................................................... 2-1

2.1 SoftMenu Setup...........................................................................2-2

2.2 Standard CMOS Features..............................................................2-4

2.3 Advanced BIOS Features..............................................................2-7

2.4 Advanced Chipset Features.........................................................2-10

2.5 Integrated Peripherals................................................................2-12

2.6 Power Management Setup..........................................................2-15

2.7 PnP/PCI Configurations ..............................................................2-17

2.8 PC Health Status........................................................................2-18

2.9 Load Fail-Safe Defaults ..............................................................2-20

2.10 Load Optimized Defaults...........................................................2-20

2.11 Set Password...........................................................................2-20

2.12 Save & Exit Setup ....................................................................2-20

2.13 Exit Without Saving..................................................................2-20

3. Driver & Utility ................................................................. 3-1

3.1 Intel Chipset Software Installation Utility .......................................3-2

iv IB9

3.2 Audio Driver................................................................................3-2

3.3 LAN Driver ..................................................................................3-2

3.4 iTE IDE Controller Driver ..............................................................3-3

3.5 USB 2.0 Driver.............................................................................3-3

3.6 ABIT EQ (The Hardware Doctor Utility)..........................................3-4

3.7 FlashMenu (BIOS Update Utility)...................................................3-5

3.8 Build A Driver Disk Under Windows Environment............................3-6

3.9 Build A Driver Disk Under DOS Environment ..................................3-7

4. Multilingual Quick Installation Guide .............................. 4-1

4.1 French//Guide d'Installation Rapide...............................................4-1

4.2 German//Kurze Installationsanleitung............................................4-3

4.3 Italian//Guida all’installazione rapida .............................................4-5

4.4 Spanish//Guía rápida de instalación...............................................4-7

4.5 Portuguese//Guia de instalação rápida ..........................................4-9

4.6 Russian//Краткое руководство по установке .............................4-11

4.7 Estonian//Kiirpaigaldusjuhend.....................................................4-13

4.8 Latvian//Ātrās instalēšanas instrukcija .........................................4-15

4.9 Lithuanian//Trumpas instaliavimo vadovas...................................4-17

4.10 Polish//Instrukcja szybkiej instalacji...........................................4-19

4.11 Hungarian//Gyorstelepítési útmutató .........................................4-21

4.12 Turkish//Hızlı Kurulum Kılavuzu.................................................4-23

4.13 Arabic// .........................................................4-25

4.14 Persian// ....................................................4-27

4.15 Japanese//クイックインストールガイド ...................................4-29

4.16 Korean//빠른 설치 가이드 .......................................................4-31

4.17 Malay//Panduan Pemasangan Ringkas.......................................4-33

4.18 Thai//!!........................................................4-35

4.19 繁體中文 ................................................................................4-37

4.19.1 規格 ..............................................................................4-37

4.19.2 快速安裝指南 .................................................................4-38

4.20 简体中文 ................................................................................4-40

4.20.1 规格 ..............................................................................4-40

4.20.2 快速安装指南 .................................................................4-41

5. Appendix .......................................................................... 5-1

5.1 Troubleshooting (How to Get Technical Support?)..........................5-1

5.1.1 Q & A.................................................................................5-1

5.1.2 Technical Support Form ......................................................5-4

5.1.3 Contact Information ............................................................5-5

Hardware Setup

IB9 1-1

1. Hardware Setup

1.1 Specifications

CPU

• Support Intel Core 2 Duo, Pentium

Extreme Edition, Pentium D, Pentium 4

Processor with 1066/800MHz FSB

Chipset

• Intel P965 / ICH8

Memory

• 4x 240-pin DIMM slots support

maximum memory capacity up to 8GB

• Supports Dual Channel DDR2

800/667/533 Un-buffered Non-ECC

memory

LAN

• Onboard 10/100/1000M PCI controller

Audio

• Onboard 7.1 CH HD Audio CODEC

Serial ATA

• 4x SATA 3Gb/s

Expansion Slots

• 1x PCI-E X16 slot

• 3x PCI-E X1 slots

• 2x PCI slots

Internal I/O Connectors

• 1x Floppy port

• 2x ATA 100 IDE connectors

• 4x SATA 3Gb/s connectors

• 3x USB 2.0 headers

• 1x FP-Audio header

• 1x CD-In connector

Rear Panel I/O

• 1x PS/2 Keyboard connector

• 1x PS/2 Mouse connector

• 1x S/PDIF Out

• 1x 7.1CH Audio Connector

• 4x USB 2.0 connectors

• 1x RJ-45 Gigabit LAN connector

ABIT Engineered

• ABIT SoftMenu

™

Technology

RoHS

• 100% Lead-free process and RoHS

compliant

Miscellaneous

• ATX form factor (305mm x 245mm)

※ Specifications and information contained herein are subject to change without

notice.

1-2 IB9

1.2 Motherboard Layout

Hardware Setup

IB9 1-3

1.3 Choosing a Computer Chassis

• Choose a chassis big enough to install this motherboard.

• As some features for this motherboard are implemented by cabling connectors on the

motherboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is possibility of adopting some more hard drives, make sure your chassis has

sufficient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port configuration of this motherboard. You can find

an I/O shield specifically designed for this motherboard in its package.

1.4 Installing Motherboard

Most computer chassis have a base with many

mounting holes to allow the motherboard to be

securely attached, and at the same time, prevent

the system from short circuits. There are two

ways to attach the motherboard to the chassis

base: (1) with studs, or (2) with spacers.

Basically, the best way to attach the board is

with studs. Only if you are unable to do this

should you attach the board with spacers. Line

up the holes on the board with the mounting holes on the chassis. If the holes line up and there

are screw holes, you can attach the board with studs. If the holes line up and there are only

slots, you can only attach with spacers. Take the tip of the spacers and insert them into the

slots. After doing this to all the slots, you can slide the board into position aligned with slots.

After the board has been positioned, check to make sure everything is OK before putting the

chassis back on.

※ Always power off the computer and unplug the AC power cord before adding or

removing any peripheral or component. Failing to so may cause severe damage

to your motherboard and/or peripherals. Plug in the AC power cord only after

you have carefully checked everything.

To install this motherboard:

1. Locate all the screw holes on the

motherboard and the chassis base.

2. Place all the studs or spacers needed on

the chassis base and have them tightened.

3. Face the motherboard’s I/O ports toward

the chassis’s rear panel.

4. Line up all the motherboard’s screw holes

with those studs or spacers on the chassis.

5. Install the motherboard with screws and

have them tightened.

※ To prevent shorting the PCB circuit,

please REMOVE the metal studs or

spacers if they are already fastened

on the chassis base and are without

mounting-holes on the motherboard

to align with.

Face the chassis’s rear panel.

1-4 IB9

1.5 Checking Jumper Settings

• For a 2-pin jumper, plug the

jumper cap on both pins will

make it CLOSE (SHORT).

Remove the jumper cap, or

plug it on either pin

(reserved for future use) will

leave it at OPEN position.

SHORT

OPEN

• For 3-pin jumper, pin 1~2 or pin 2~3 can be

shorted by plugging the jumper cap in.

Pin 1~2 SHORT

Pin 2~3 SHORT

1.5.1 CMOS Memory Clearing Header and Backup Battery

The time to clear the CMOS memory occurs when (a)

the CMOS data becomes corrupted, (b) you forgot

the supervisor or user password preset in the BIOS

menu, (c) you are unable to boot-up the system

because the CPU ratio/clock was incorrectly set in the

BIOS menu, or (d) whenever there is modification on

the CPU or memory modules.

This header uses a jumper cap to clear the CMOS

memory and have it reconfigured to the default

values stored in BIOS.

• Pins 1 and 2 shorted

(Default): Normal

operation.

• Pins 2 and 3 shorted:

Clear CMOS memory.

To clear the CMOS memory and load in the default values:

1. Power off the system.

2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper

cap back to its default settings --- pin 1 and pin 2 shorted.

3. Power on the system.

4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS

setup menu right after powering on system.

5. Set the CPU operating speed back to its default or an appropriate value.

6. Save and exit the BIOS setup menu.

Hardware Setup

IB9 1-5

CMOS Backup Battery:

An onboard battery saves the CMOS memory to keep the BIOS information stays on even after

disconnected your system with power source. Nevertheless, this backup battery exhausts after

some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS

checksum error” displays on monitor, this backup battery is no longer functional and has to

be renewed.

To renew the backup battery:

1. Power off the system and disconnect with AC power source.

2. Remove the exhausted battery.

3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its

positive polarity.

4. Connect AC power source and power on the system.

5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.

CAUTION:

※ Danger of explosion may arise if the battery is incorrectly renewed.

※ Renew only with the same or equivalent type recommended by the battery

manufacturer.

※ Dispose of used batteries according to the battery manufacturer’s instructions.

1-6 IB9

1.5.2 Wake-up Header

These headers use a jumper cap to enable/disable the wake-up function.

• USB-PWR1:

Pin 1-2 shorted (Default): Disable wake-up function support at USB1 port.

Pin 2-3 shorted: Enable wake-up function support at USB1 port.

• USB-PWR2:

Pin 1-2 shorted (Default): Disable wake-up function support at USB2 port.

Pin 2-3 shorted: Enable wake-up function support at USB2 port

Hardware Setup

IB9 1-7

1.6 Connecting Chassis Components

1.6.1 ATX Power Connectors

These connectors provide the connection from an ATX power supply. As the plugs from the

power supply fit in only one orientation, find the correct one and push firmly down into these

connectors.

ATX 24-Pin Power Connector:

The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector.

Connect from pin-1 for either type. However, a 20-pin power supply may cause the system

unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W

or higher is recommended.

ATX 12V 4-Pin Power Connector:

This connector supplies power to CPU. The system will not start without connecting power to

this one.

1-8 IB9

1.6.2 Front Panel Switches & Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel.

Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure

below stands for positive polarity for the LED connection. Please pay attention when connecting

these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection

of the switches could cause system malfunction.

• HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis front panel.

• RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis front panel.

• SPKR (Pin 13, 15, 17, 19):

Connects to the System Speaker cable of chassis.

• SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there is one) of chassis front panel.

• PWR (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

• PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

Hardware Setup

IB9 1-9

1.6.3 FAN Power Connectors

These connectors each provide power to the cooling fans installed in your system.

• CPUFAN1: CPU Fan Power Connector

• SYSFAN1: System Fan Power Connector

• AUXFAN1~2: Auxiliary Fan Power Connector

※ These fan connectors are not jumpers. DO NOT place jumper caps on these

connectors.

1-10 IB9

1.7 Installing Hardware

※ DO NOT scratch the motherboard when installing hardware. An accidentally

scratch of a tiny surface-mount component may seriously damage the

motherboard.

※ In order to protect the contact pins, please pay attention to these notices:

1. A maximum 20 cycles of CPU installation is recommended.

2. Never touch the contact pins with fingers or any object.

3. Always put on the cap when the CPU is not in use.

1.7.1 CPU Socket 775

※ The installation procedures vary with different types of CPU fan-and-heatsink

assembly. The one shown here is served for demo only. For detailed

information on how to install the one you bought, refer to its installation

guidelines.

1. Place the board so as to let the

lever-hook of the socket is on your left side.

Use your left thumb and forefinger to hold

the lever hook, pull it away from the retention

tab. Rotate the lever to fully open position.

2. Use your right-thumb to raise the load

plate. Lift it up to fully open position.

3. Use your right thumb and forefinger to

grasp the CPU package. Be sure to grasp on

the edge of the substrate, and face the Pin-1

indicator toward the bottom-left side. Aim at

the socket and place the CPU package

vertical down into the socket.

4. Visually inspect if the CPU is seated well

into the socket. The alignment key must be

located in the notch of package.

Hardware Setup

IB9 1-11

5. Use your left hand to hold the load plate,

and use your right thumb to peel the cap off.

The cap plays an important role in

protecting contact pins. In order to

prevent bent pin, PUT ON the cap after

operation or testing.

6. Lower the plate onto the CPU package.

Engage the load lever while gently pressing

down the load plate.

7. Secure the lever with the hook under

retention tab.

8. Place the heatsink and fan assembly onto

the socket. Align the four fasteners toward

the four mounting holes on the motherboard.

9. Press each of the four fasteners down

into the mounting holes. Rotate the fastener

clock-wise to lock the heatsink and fan

assembly into position.

10. Attach the four-pin power plug from the

heatsink and fan assembly to the CPU FAN

connector.

※ A higher fan speed will be helpful for better airflow and heat-dissipation.

Nevertheless, stay alert to touch any heatsink since the high temperature

generated by the working system is still possible.

1-12 IB9

1.7.2 DDR2 Memory Slots

• To reach the optimum performance in dual-channel configurations, install identical DDR2

DIMM pairs for each channel.

• Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain

memory modules from the same vendor.

※ Usually there is no hardware or BIOS setup required after adding or removing

memory modules, but you will have to clear the CMOS memory first if any

memory module related problem occurs.

To install system memory:

1. Power off the computer and unplug the

AC power cord before installing or

removing memory modules.

2. Locate the DIMM slot on the board.

3. Hold two edges of the DIMM module

carefully, keep away from touching its

connectors.

4. Align the notch key on the module with

the rib on the slot.

5. Firmly press the module into the slots until the ejector tabs at both sides of the slot

automatically snap into the mounting notch. Do not force the DIMM module in with extra

force as the DIMM module only fits in one direction.

6. To remove the DIMM modules, push the two ejector tabs on the slot outward

simultaneously, and then pull out the DIMM module.

※ Static electricity can damage the electronic components of the computer or

optional boards. Before starting these procedures, ensure that you are

discharged of static electricity by touching a grounded metal object briefly.

Hardware Setup

IB9 1-13

1.8 Connecting Peripheral Devices

1.8.1 Floppy and IDE Disk Drive Connectors

The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.

Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two

connectors on the other end to the floppy disk drives connector. Generally you need only one

floppy disk drive in your system.

※ The red line on the ribbon cable must be aligned with pin-1 on both the FDC1

port and the floppy connector.

Each of the IDE port connects up to two IDE drives

at Ultra ATA/100 mode by one 40-pin, 80-conductor,

and 3-connector Ultra ATA/66 ribbon cables.

Connect the sin

le end (blue connector) at the lon

length of ribbon cable to the IDE port of this board,

the other two ends (gray and black connector) at the

shorter length of the ribbon cable to the connectors

of your hard drives.

※ Make sure to configure the “Master” and “Slave” relation before connecting

two drives by one single ribbon cable. The red line on the ribbon cable must be

aligned with pin-1 on both the IDE port and the hard-drive connector.

※ You will have to install the “iTE IDE Controller Driver” first to enable the IDE1

and IDE2 connections.

1-14 IB9

1.8.2 Serial ATA Connectors

Each SATA connector serves as one single channel to connect one SATA device by SATA cable.

To connect SATA device:

1. Attach either end of the signal cable

to the SATA connector on

motherboard. Attach the other end to

SATA device.

2. Attach the SATA power cable to the

SATA device and connect the other

end from the power supply.

※ The motherboard in this illustration is served for DEMO only, may not be the

same type or model as the one described in this user’s manual.

Hardware Setup

IB9 1-15

1.8.3 Additional USB 2.0 Port Headers

Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O

panel or the front-mounted USB ports of your chassis.

Pin Pin Assignment Pin Pin Assignment

1 VCC 2 VCC

3 Data0 - 4 Data1 -

5 Data0 + 6 Data1 +

7 Ground 8 Ground

10 NC

※ Make sure the connecting cable bears the same pin assignment.

1-16 IB9

1.8.4 Internal Audio Connectors

This connector connects to the audio output of internal CD-ROM drive or add-on card.

1.8.5 Front Panel Audio Connection Header

This header provides the front panel connection for HD (High Definition)

Audio, yet for AC’97 Audio CODEC connection, you must carefully check

the pin assignment before connecting from the front panel module. An

incorrect connection may cause malfunction or even damage the

motherboard.

※ Please do not connect the “Ground” cable or “USB VCC” cable

from the front panel module to the Pin 4 “AVCC” of this

header.

Pin Assignment

(HD AUDIO)

Pin Assignment

(AC’97 AUDIO)

1 MIC2 L 1 MIC In

2 AGND 2 GND

3 MIC2 R 3 MIC Power

4 AVCC 4NC

5 FRO-R 5 Line Out (R)

6 MIC2_JD 6 NC

7 F_IO_SEN 7 NC

9 FRO-L 9 Line Out (L)

10 LINE2_JD 10 NC

Leht laadib ...

Abit IB9 Omaniku manuaal

Bränd: Abit

Mudel: IB9

Kategooria: Emaplaadid

Tüüp: Omaniku manuaal

Laadige alla PDF

aruanne

teistes keeltes

italiano: Abit IB9 Manuale del proprietario
English: Abit IB9 Owner's manual

Abit IB9 Omaniku manuaal

Abit IB9 Omaniku manuaal

teistes keeltes

Muud dokumendid