Samsung VR30T80313W Kasutusjuhend

Jet Bot

User manual

VR30T80**** series

• For full manual, Scan QR code or access online at https://www.samsung.com

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

2

04

01

07

02

06

05

03

04

08

09

04

03

02

01

06

08

05

09

04

07

03

01

02

Top

01

Obstacle Sensor

02

Power switch

03

LiDAR Sensor

04

Dustbin

05

Start/stop button

06

Docking (Recharging)

button

07

Status Indicator

08

Docking Sensor Window

09

Upper Cover

Bottom

01

Charging Pin

02

Brush

03

Brush Cover

04

Cliff Sensor

05

Roller

06

Battery Cover

07

Driving Wheel

08

Spin Brush

09

Brush Cover Lock

Docking Station

01

Charging Terminal

02

Charging Signal

Transmitter

03

Power cord groove

Docking Station Pre-motor Filter: 2 units

(Inside the product: 1 unit,

Spare: 1 unit)

Spin Brush: 2 units

(Inside the product: 1 unit,

Spare: 1 unit)

Battery Charger/

Power cord

Boundary Markers User Manual

Accessories may differ depending on the models.

• For the normal use of the Jet Bot’s functions,

the SmartThings connection is required.

3

1 2

0.5 m

1 m

3

A

4

B-1

12

B-2

1 2

3

1

4

B

ONOFF

5

C

1 2

3 4

5 6

7 8

C-1

24H

6

C

C-2

1 2

3 4

C-3

7

C-5

C-4

2

1

C

English

English8

Operation and maintenance

A. Installation

NOTE

• Install the Docking Station in a place where

the floor and wall are level.

• If the Battery Charger cord is too long for

the installation environment, coil the power

cord around the cable management post,

then put it in the fixing groove at the rear

of the Docking Station.

B. Using the Jet Bot

B-1 Charging the Jet Bot

Charging

• Open the upper cover of the Jet Bot and

remove the white gasket.

• Remove the yellow gasket attached to the

power switch at the side of the Jet Bot and

press the power switch to turn the Jet Bot

on.

• Place the Jet Bot on the Docking Station

manually to start charging.

- Make sure the charging terminals on

the Jet Bot and the Docking Station are

aligned.

• Check the charging status.

- When charging starts, the Status Indicator

of the Jet Bot turns on (red, orange, or

yellow depending on charging progress),

it rises gradually, and changes to green

when the charging is complete.

Docking (Recharging)

• You can return the Jet Bot to the Docking

Station while cleaning to recharge.

- Press the [ ] on the Jet Bot or use the

SmartThings App to select the recharging

function.

B-2 Starting cleaning

• Press the [ ] on the Jet Bot to start

cleaning in Auto Clean.

• Press the [ ] on the Jet Bot to stop

operation while cleaning.

- When pressing the [ ], the Jet Bot

returns to the Docking Station and starts

charging.

C. Cleaning the Jet Bot

Before maintenance work, you should turn off

the power switch at the side of the Jet Bot.

C-1 Emptying and cleaning the Dustbin

• Remove the dust on the filter and the

Dustbin, clean them with water, and dry

completely in the shade.

C-2 Cleaning the brush

C-3 Cleaning the Sensor Window

• Wipe the Sensor Window with a soft cloth.

C-4 Cleaning the Driving Wheel

C-5 Cleaning the Spin Brush

• If curl or deformation occurs, cover the

Spin Brush with a hot steamed cloth for 10

seconds, then wipe the Spin Brush.

• For detailed methods of use

and cleaning, refer to the QR

code.

English

English 9

Safety information

• Before operating the appliance, please read

this manual thoroughly and retain it for

your reference.

• Because the following operating

instructions cover various models, the

characteristics of your vacuum cleaner may

differ slightly from those described in this

manual.

Caution/Warning symbols used

WARNING

Indicates that a danger of death or serious

injury exists.

CAUTION

Indicates that a risk of personal injury or

material damage exists.

Other symbols used

NOTE

Indicates that the following text contains

additional important information.

Failure to meet these requirements could

cause damage to the internal parts of the

vacuum and void your warranty.

General

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Use only as described in this manual.

• Do not operate the Jet Bot or the Docking

Station if it has been damaged in any way.

• If the vacuum cleaner is not working as it

should, has been dropped, damaged, left

outdoors, or dropped in water, return it to a

customer care center.

• Do not handle the Docking Station or the

Jet Bot if your hands are wet.

• Use only on dry, indoor surfaces.

• This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children should not

play with the appliance. Children should

not clean or perform maintenance on the

vacuum without adult supervision.

• Move the cords of other appliances so they

are not in the area that is to be cleaned.

• Do not operate the vacuum in a room

where an infant or child is sleeping.

• Do not operate the vacuum in an area

where there are lit candles or fragile

objects on the floor.

• Do not operate the vacuum in a room that

has lit candles on furniture that the vacuum

may accidentally hit or bump into.

• Do not allow children to sit on the vacuum.

• Do not use the vacuum on a wet surface.

• If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in

order to avoid a hazard.

• For information on Samsung’s

environmental commitments and product

specific regulatory obligations e.g. REACH

(WEEE, Batteries) visit: samsung.com/

uk/aboutsamsung/samsungelectronics/

corporatecitizenship/data_corner.html

Docking Station

• Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

• Do not use outdoors or on wet surfaces.

• Unplug the Docking Station from the outlet

when not in use and before servicing.

• Use only the Docking Station supplied by

the manufacturer to recharge.

• Do not use with a damaged cord or a plug

or a loose power outlet.

English

English10

• Do not pull or carry by the cord, use the

cord as a handle, close the door on the

cord, or pull the cord around sharp edges

or corners. Keep the cord away from heated

surfaces.

• Do not use extension cords or outlets with

inadequate current carrying capacity.

• Do not unplug by pulling on the cord. To

unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as

they will explode at high temperatures.

• Do not attempt to open the Docking Station.

Repairs should only be carried out by a

qualified customer care center.

• Do not expose the Docking Station to high

temperatures or allow moisture or humidity

of any kind to come into contact with the

Docking Station.

• Do not charge the non-rechargeable

batteries with the Docking Station.

Jet Bot

• Do not pick up hard or sharp objects such

as glass, nails, screws, coins, and etc.

• Do not use without a filter in place. When

servicing the unit, never put fingers or

other objects into the fan chamber in case

the unit accidentally turns on.

• Do not put any objects into openings.

Do not use with any openings blocked;

keep openings free of dust, lint, hair, and

anything that may reduce air flow.

• Do not pick up toxic materials (chlorine

bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning or

smoking, such as cigarettes, matches, or hot

ashes.

• Do not use to pick up flammable or

combustible liquids such as gasoline or use

in areas where they may be present.

• Also do not use in:

- Locations with candles or desk lamps on

the floor.

- Locations with unattended fires (fire or

embers).

- Locations with distilled alcohol, thinner,

ashtrays with burning cigarettes, etc.

• Do not use the Jet Bot in an enclosed

space filled with vapors given off by oil

based paint, paint thinner, moth proofing

substances, flammable dust, or other

explosive or toxic vapors.

• Leaks from battery cells can occur under

extreme usage or temperature conditions.

If the liquid gets on the skin, wash quickly

with water. If the liquid gets into the eyes,

flush them immediately with clean water

for a minimum of 10 minutes. Seek medical

attention.

Power related

WARNING

• Please prevent any risk of electric shock or

fire.

- Do not damage the power cord.

- Do not pull the power cord too hard or

touch the power plug with wet hands.

- Do not use a power source other than

rated volatge of the charger and also do

not use a multi-outlet to supply power to

a number of devices at the same time. (Do

not leave the cord carelessly on the floor.)

- Do not use a damaged power plug, a

power cord or a loose power outlet.

• Clean dust or any foreign matter on the pin

and the contact part of the power plug.

- There is a risk of electric shock or

malfunction.

Safety information

English

English 11

Before use

WARNING

• Do not use the Jet Bot near a heater or

combustible materials.

- Do not use the Jet Bot near fire or flame

such as a movable heater, a candlelight,

a desk lamp, a fireplace, etc. or in a place

where combustible materials such as

gasoline, alcohol, thinner, etc. exist.

• Make sure there are no dangerous objects

around the Jet Bot’s cleaning area to

prevent collision and unplug any electric

heaters or fans.

- The Jet Bot can be damaged or

malfunction.

• The Jet Bot is intended for household

use therefore do not use it in an attic,

basement, storage, an industrial building,

out of indoor space, places with moisture

(such as a bathroom, a laundry room), on

the table or shelves.

- The Jet Bot can be damaged or

malfunction.

• Attach the Boundary Markers to a place

where the Jet Bot may fall such as a stair

or a banister to prevent product damage

and injury.

- Please keep the Cliff Sensor clean all the

time for safety.

• Be sure the Jet Bot does not suck in or

touch any kind of liquids (water, beverage,

filth, etc.).

- The Jet Bot can be severely damaged

and it may contaminate other areas if the

wheels pass through liquid.

• Do not spill any liquids on the Docking

Station.

- There is a risk of fire or electric shock.

• Do not use the Docking Station for anything

other than its intended purposes.

- There is a risk of fire or severe damage to

the Docking Station.

• Always keep the Cliff Sensor clean for your

safety.

• As this wireless installation may cause

radio interference, it cannot provide a

service related with human safety.

CAUTION

• Insert the Dustbin before using the Jet Bot.

• When installing the Docking Station, do not

leave the cord carelessly on the floor since

the Jet Bot may get tangled by it.

• To clean all areas of your house, open all

rooms and set the No-go Zones with the

SmartThing App or attach the Boundary

Markers to the places where the Jet Bot

may get damaged such as a front door, a

veranda, a bathroom, and stairs for safety.

• Follow these recommendations for proper

automatic recharging.

- Always turn on the power of the Docking

Station.

- Install the Docking Station where the Jet

Bot can easily find.

- Do not leave any objects in front of the

Docking Station.

• Do not use the Jet Bot on black colored

floors.

- The Jet Bot may not be able to operate

normally.

• Do not place any objects within 0.5 m of

either side of the Docking Station or within

1 m of the front of the Docking Station.

• Make sure the Docking Station’s charging

contact is not damaged or have any foreign

matter on it.

• For the very low areas where the Jet Bot

may get stuck, set the No-go Zones with

the SmartThing App or attach the Boundary

Markers to prevent the Jet Bot from getting

in.

• Do not install the Docking Station in an area

with a dark floor.

- If the floor around the Docking Station is

dark, recharging is hindered.

• Move any obstacles that may disturb the

Jet Bot’s movement (such as children’s

indoor swing or slides) before cleaning.

Safety information

English

English12

• Do not use the Jet Bot in a place which is

narrower than its turning radius 0.5 m or

less.

• Before operating the Jet Bot, remove the

objects which could break such as glass, a

frame, a mirror, and porcelain items so that

the Jet Bot works without interruption.

• If a brush or a brush cover is not assembled

correctly, scratches may occur on the floor,

or product malfunction may occur.

• Use both hands to carry the product.

• Do not place the Docking Station in a

place where people pass by frequently, in

entrance way or narrow passage.

- People may trip over it and be injured, or

product damage may occur.

• Do not push the Docking Station.

In use

WARNING

• If any abnormal sounds, smells or smoke

come from the Jet Bot, immediately shut

off the power switch of the Jet Bot and

contact a service center.

CAUTION

• Using the Jet Bot on a thick carpet may

damage both the Jet Bot and the carpet.

- The Jet Bot cannot pass over a carpet

with fiber longer than 2 cm.

• Do not use the Jet Bot on tables or other

high surfaces.

- There is a risk of damage if it falls.

• The Jet Bot may bump into chairs or desk

legs, therefore move them away for faster

and efficient cleaning.

• When the Jet Bot is operating, do not lift it

up or carry it to another area.

• Do not hold by Driving Wheels of the Jet

Bot when carrying it to another area.

• Do not put any objects on top of the Jet Bot

since it may cause malfunction of the LiDAR

sensor or the Jet Bot.

• Remove any large papers or plastic bags

immediately when using the Jet Bot since

they may block the intake.

• Do not lie down around the Jet Bot that is

running.

- Your hair may be caught in the brush,

resulting in physical injury.

• Do not allow children to play with the Jet

Bot.

• Make sure hair, fingers, clothes do not get

caught in a spin brush or Driving Wheels.

• Do not allow children to sit on the Jet Bot

and do not place an object on the Jet Bot.

• Leave over 3 cm space from the inner

doorstep placed in the entrance. Otherwise,

the robot vacuum can ride on it and go

outside.

Cleaning and maintenance

WARNING

• When the power cord is damaged, contact

a service center to get it replaced by a

certified repairman.

- There is a risk of fire or electric shock.

• Please check with a SAMSUNG Electronics

service center when replacing batteries.

- Using batteries from other products can

cause malfunction.

• Be careful not to put your finger into the

revolving LiDAR sensor. Otherwise, your

finger may get injured.

CAUTION

• Prevent any damage to the Jet Bot by

complying with the following.

- Do not clean the Jet Bot by spraying

water directly onto it or use a volatile

substance such as benzene, thinner, or

alcohol to clean it.

• Do not disassemble or repair the Jet Bot.

This should only be done by a certified

repairman.

Safety information

English

English 13

Safety information

• Always keep the Obstacle Sensor Window

and the Cliff Sensor Window clear.

- If foreign matter accumulates, sensors

may malfunction.

• Do not store the Jet Bot in a car.

• Be careful that the LiDAR sensor is not

exposed to a direct light such as sun light,

infrared light, etc.

- The direct light can affect the performance

of the LiDAR sensor.

• When carrying the Jet Bot, be careful not to

let it drop.

- The impact from the drop can affect the

operation or performance of the LiDAR

sensor.

• Do not look at the transmitting part (a

laser) of the revolving LiDAR sensor

horizontally.

• Be careful not to insert a tool such as a

chopstick into the revolving LiDAR sensor.

Otherwise, the LiDAR sensor may work

abnormally or malfunction.

• Before cleaning, remove objects which are

less than 9 cm height and are lightly on the

floor as the Jet Bot can push along them,

or the objects can be caught in the Jet Bot’s

spin brush or driving wheels. (Fixed objects

can be detected by the Jet Bot when its

bumper is pressed and will avoid them.)

• If oil such as cooking oil is on the floor, the

Jet Bot may become stationary because the

floor is slippery. Remove the oil first before

cleaning with the Jet Bot.

English

English14

Installation

NOTE

• If the cleaning area is wooden floors, it is

best to install the Docking Station along the

grain of wooden floors.

• If the power switch is off, the Jet Bot will

not charge even if it is docked on the

Docking Station.

• Always keep the Docking Station on.

- If power is not supplied to the Docking

Station, the Jet Bot cannot find it and

cannot automatically recharge.

- If the Jet Bot is left detached from the

Docking Station, the battery will drain

naturally.

• Do not attach the Boundary Markers as

(-----) shape.

- The Jet Bot may not detect it and cross

the boundary.

Charging

NOTE

• If the battery overheats during charging, it

may take longer to charge.

• When auto charging is not working, do the

following:

- Turn the power switch (at the side the Jet

Bot) off and on again.

- Unplug the Docking Station’s power plug

and then plug it back on.

- Unplug the Docking Station, and then

check whether there is any foreign matter

on the charging pins and clean charging

pins of the Jet Bot and the Docking

Station with a dry cloth or rag.

- Check for any obstacles such as reflective

objects, chairs, etc. near the Docking

Station.

• If the Jet Bot is left detached from the

Docking Station, the battery will drain

naturally.

- Try to keep the Jet Bot being charged on

the Docking Station. (However, turn off

the power switch and leave the Docking

Station unplugged when planning to leave

the house for long periods of time by

going on a business trip or vacation, etc.)

Using

NOTE

• The Jet Bot may get caught on thresholds

of entrance door or veranda, etc. during

cleaning.

- To restart operation, shut off the power

switch, move the Jet Bot to an area where

it can move easily, and then turn on the

power again.

• In a dark area, the Jet Bot may not

recognize an object.

- Before cleaning, remove obstacles on the

floor.

• The Jet Bot cannot completely clean areas

which it cannot enter, such as small space

between the corner, between the sofas or

walls, etc.

- Please use another cleaning tool to clean

them regularly.

• The Jet Bot cannot vacuum clumps of dirt,

so some may remain on the floor after

cleaning.

- Please use another cleaning tool to clean

them regularly.

• After turning the Jet Bot off, wait for a

while and then turn it on for a normal

rebooting.

Notes and cautions

English

English 15

Cleaning and maintenance

NOTE

• If you washed the Dustbin and filter with

water

- Dustbin: Completely wipe out the water.

- Filter: Completely dry it in the shade

before use.

CAUTION

• Watch your fingers when attaching or

detaching the filter, since they may get

stuck in the Dustbin’s intake.

• To avoid blockages by foreign matter, do

not let the Jet Bot vacuum up toothpicks,

cotton swabs, etc.

• If it is difficult to remove foreign matter

from the brush, contact an authorized

SAMSUNG service center.

• Since the brush sweeps dirt up from the

floor during cleaning, foreign matter such

as a thin and long thread, long hair, etc.

may get caught in it. For the best cleaning

results, check and clean it regularly.

• Turn off the Jet Bot before cleaning or

maintenance work.

• If a brush or a brush cover is not assembled

correctly after the maintenance work,

scratches may occur on the floor, or

product malfunction may occur. Therefore,

assemble them correctly by checking the

maintenance method.

Battery usage

NOTE

• When you purchase a battery, check the

SAMSUNG logo ( ) attached on the

battery and the model name, then contact a

service center.

• This battery is exclusively for the SAMSUNG

Electronics Jet Bot. Do not use it for any

other products or purposes.

• Do not disassemble or modify the battery.

• Do not throw the battery out in fire or heat

it.

• Do not connect any metallic object to the

charging contacts (+, -).

• Store the battery indoors (at 0 °C~40 °C).

• If the battery malfunctions, do not

disassemble it yourself. Contact your

nearest SAMSUNG service center.

• As the battery is used over a length of time,

the battery charging time and usage time

decreases. In this case, contact a service

center and replace it with a new battery.

• Do not disassemble the battery yourself

and make sure short circuit of +, - poles

does not occur.

• When battery leak occurs, make sure it

does not touch your skin or eyes.

Notes and cautions

English

English16

The SmartThings App is only compatible with

models that have a Wi-Fi function.

If you do not have a Wi-Fi router, you cannot

use the SmartThings App.

Downloading the SmartThings App

• Download and install the SmartThings

App from the markets (Google Play Store,

Apple App Store, or SAMSUNG Galaxy

Store). To find the app, use the keyword

“SmartThings”.

NOTE

• SmartThings is incompatible with some

tablets and some mobile devices.

• Some iPads and some mobile devices may

not be supported.

• Visit Play Store or App Store to see if

your mobile device is compatible with

SmartThings.

• The supporting software version of the

SmartThings app is subject to change

according to the OS supporting policy the

manufacturer provides. In addition, as

for the SmartThings app or the functions

that the app supports, the new application

update policy on the existing OS version

can be suspended due to usability or

security reasons.

• The SmartThings app is subject to change

without notice to improve usability

or performance. As the mobile phone

OS version is updated every year, the

SmartThings is also updated continually

according to the latest OS.

• If you have enquiries regarding the items

mentioned above, please contact us on

[email protected].

Setting up a SAMSUNG account

• You must sign in to a SAMSUNG account

before using the SmartThings App.

• To set up a SAMSUNG account, you can

follow the directions provided by the

SmartThings App.

• Or, if you have a SAMSUNG smartphone,

you can add your SAMSUNG account in the

setting app of your smartphone. Then, it

will automatically sign in to your SAMSUNG

account and you can use the SmartThings App.

Registering a device to the SmartThings App

1 Connect your smartphone to your wireless

router.

- If the smartphone is not connected, turn

on the Wi-Fi in the Settings App and

select a wireless router you want to

connect to.

- Set your smartphone to use Wi-Fi only

and connect a device.

2 Launch the SmartThings App on your

smartphone.

3 If a pop-up saying that a new device has

been found appears, tap ADD NOW.

- If the pop-up does not appear, add a

device by selecting the ‘Home appliances’

category ‘Robot cleaner’ and the Jet

Bot to connect.

- If you scan the SmartThings QR code

attached on the Jet Bot, you can connect

to the Jet Bot more easily.

4 [Android] The connection to your device

will be progressed automatically.

- [iOS] Open the setting app, and select

[vacuum]_E30AJT** in the Wi-Fi list.

5 Provide the authentication when you are

directed to do so.

6 [Android] The connection to your wireless

router will be progressed automatically.

- [iOS] Open the setting app, and select the

wireless router in the Wi-Fi list.

7 When the product registration is complete,

the Jet Bot device card is added.

NOTE

• Setting Wi-Fi On/Off: Hold the [ ] button

down for 7 seconds to switch the Wi-Fi

off or on to use again while the vacuum

cleaner is on standby or charging.

SmartThings App

English

English 17

SmartThings App

Functions of the SmartThings App

Classification Functions Explanation

Monitoring Cleaning Report • You can check the result of the last cleaning.

• You can check the histories of last 50 cleanings.

Control

Dock • You can stop cleaning and have the Jet Bot return to

the Docking Station.

Pause • You can stop cleaning or restart cleaning.

Cleaning Mode • You can set the cleaning mode you want.

Cleaning Functions

• You can set various cleaning functions.

- For some functions, you need to create a map

first.

- For Room Clean and Spot Clean, you can choose

only one of them, and the default setting is ‘All’

(All Rooms).

• When the Jet Bot is in the Room Clean or the Spot

Clean, it may pass an unselected area to go to the

cleaning place or to recharge.

Schedule

• You can start designated cleaning at the scheduled time.

Setting

Sound Mode • You can set the voice guide to [Voice], [Sound Effect],

or [Mute].

Language • The Jet Bot supports 14 languages.

Volume • You can control the volume of the voice guide.

Downtime

• At the designated time, the Jet Bot stops cleaning

and returns to the Docking Station.

- You may start cleaning during Downtime.

Find Robot Vacuum • The Jet Bot makes a sound so that a user can find it.

Child Lock

• The Jet Bot locks its buttons so that they do not

function. To unlock the buttons, turn the Jet Bot off

and then on again.

Notice

Cleaning completed • When cleaning is complete, you can receive cleaning

completion notice.

Check Notice • If the Jet Bot needs to be checked, you can receive a

notice.

Manage maps

No-go Zones

• You can set a zone where you do not want the Jet

Bot to clean.

- You can create maximum 15 zones.

Edit Map • You can divide or combine rooms on the created map.

• You can change the name of a room.

Reset Map • Reset the saved map.

English

English18

Troubleshooting

Symptom Checklist

The Jet Bot is not

working at all.

• Check if the power switch is on.

• Check if the Status Indicator is on.

• Check if the Jet Bot's battery is depleted.

- When the Jet Bot’s Status Indicator turns red and stays red, place

the Jet Bot manually on the Docking Station to charge it.

• When you manually charge the Jet Bot due to complete discharge of

its battery, the buttons on the Jet Bot do not work. When charging is

partially complete (about 10-20 minutes later), the Status Indicator is

on and the buttons work again.

The Jet Bot has

stopped during

cleaning.

• When the Jet Bot’s Status Indicator turns red and stays red, place the

Jet Bot manually on the Docking Station to charge it.

• When the Jet Bot is immobilized by an obstacle such as a cord,

obstacles, threshold, a raised spot, etc., pick it up and move it away

from the obstacle.

- If any fabric or string is caught in a Driving Wheel, turn off the

power switch and remove the fabric or string before using it

again.

• Check whether the No-go Zones are set.

Suction power is weak.

• When there’s too much dust in the Dustbin, suction power may get

weakened. Turn off the power switch and empty the Dustbin.

• If the brush at the bottom of the Jet Bot is blocked by foreign matter,

turn off the power switch and remove foreign matter from the brush.

• When noise suddenly increases, turn off the power switch and empty

the Dustbin.

The Jet Bot cannot find

the Docking Station.

• Check if there’s a power failure or whether the power plug is

unplugged.

• Remove any obstacles around the Docking Station that may prevent

the Jet Bot from returning to the Docking Station.

• When there’s foreign matter on the charging terminals, charging can

be affected. Clean the foreign matter off the terminals.

The Jet Bot does not

detect the Boundary

Marker and crosses the

boundary.

• Make sure the Boundary Markers are attached as ( ) shape at

15 cm before the locations where the Jet Bot should not cross.

English

English 19

Product specification

[Unit : mm]

Classification Items VR30T80**** series

Mechanical

specications

Weight 3.4 kg

Cleaning method LiDAR location recognition

Button method of the Jet Bot Touch type

Electrical

specications

Power consumption of

the Jet Bot 60 W (Spot Clean)

Battery specication Lithium-ion 21.9 V / 52.56 Wh

Cleaning part

Charging type Auto charging / Manual charging

Cleaning Functions Auto Clean, Room Clean, Spot Clean

Additional functions Energy-Saving Mode, Downtime Mode,

Scheduled Cleaning, No-go Zones setting

Charging time About 240 minutes

Cleaning time

(Based on a

wooden oor)

Max About 60 minutes

Smart About 60-90 minutes

Normal About 90 minutes

Wi-Fi

Frequency range 2412 - 2472 MHz

Transmitter power(Max) 20 dBm

• Hereby, Samsung Electronics, declares that the radio equipment type appliance is in

compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is

available at the following internet address: The official Declaration of conformity may be

found at http://www.samsung.com, go to Support > Search Product Support and enter the

model name.

• Charging and cleaning time may differ depending on the conditions of use.

• You can set the Downtime, the Scheduled Cleaning, the No-go Zones at the SmartThings App.

Height 99.8

Width 350

Depth 350

Height 105

Width 154

Depth 186

English

English20

Open Source Announcement

The software included in this product contains open source software.

To obtain the source code covered under licenses which have the obligation of publishing source

code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model

name.

It is also possible to obtain the complete corresponding source code in a physical medium such

as a CD-ROM; a minimal charge will be required.

The following URL http://opensource.samsung.com/opensource/VR9500_0/seq/0 leads to open

source license information as related to this product. This offer is valid to anyone in receipt of

this information.

Leht laadib ...

Samsung VR30T80313W Kasutusjuhend

Samsung VR30T80313W Kasutusjuhend

teistes keeltes